ZLZhou-Long Li

Zhou-Long Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zhou-Long Li has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Smooth Joint Motion Planning for Robot Polishing by Redundancy Optimization

    by Hanqian Wu, Zhoulong Li, Rui Wang, Zhonghe Luo, Limin Zhu

  • An Accurate Method for Determining Cutter-Workpiece Engagements in Five-Axis Milling With a General Tool Considering Cutter Runout

    by Zhou-Long Li, Li-Min Zhu

    Cutter runout is universal and inevitable in milling process and has a direct impact on the shape of the in-process geometry. However, most of the works on the cutter-workpiece engagement (CWE) extraction neglect the cutter runout impact, which will result in a loss of precision. In this paper, an accurate method is presented to obtain CWE boundaries in five-axis milling with a general tool integrating the cutter runout impact. First, each flute's rotary surface is analytically derived. Then, by intersecting the section circle corresponding to the current flute with each of the rotary surface formed by previous flutes, a set of candidate feasible contact arcs (CFCAs) are obtained, and the valid feasible contact arc (VFCA) is defined as the common intersection of these CFCAs. Next, by intersecting the VFCA with the workpiece surfaces, the partial arc which locates inside the workpiece volume is extracted as the engagement arc. Finally, the CWE map is plotted by mapping a set of engagement arcs to a 2D space. To validate the proposed method, the CWE maps with/without integrating the cutter runout impact in five-axis milling of an axial compressor blisk are extracted and compared. The results reveal that the shape of CWE boundaries is changed a lot owing to the cutter runout impact. A cutting force comparison experiment has been carried out to show that the proposed method will lead to higher prediction accuracy especially in the finish milling process with low immersion angle.


  • Mechanistic Modeling of Five-Axis Machining With a Flat End Mill Considering Bottom Edge Cutting Effect

    by Zhou-Long Li, Li-Min Zhu

    In five-axis milling, the bottom edge of a flat end mill is probably involved in cutting when the lead angle of tool axis changes to negative. The mechanistic model will lose accuracy if the bottom edge cutting effect is neglected. In this paper, an improved mechanistic model of five-axis machining with a flat end mill is presented to accurately predict cutting forces by combining the cutting effects of both side and bottom edges. Based on the kinematic analysis of the radial line located at the tool bottom part, the feasible contact radial line (FCRL) is analytically extracted. Then, boundaries of the bottom cutter-workpiece engagements (CWEs) are obtained by intersecting the FCRL with workpiece surfaces and identifying the inclusion relation of its endpoints with the workpiece volume. Next, an analytical method is proposed to calculate the cutting width and the chip area by considering five-axis motions of the tool. Finally, the method of calibrating bottom-cutting force coefficients by conducting a series of plunge milling tests at various feedrates is proposed, and the improved mechanistic model is then applied to predict cutting forces. The five-axis milling with a negative lead angle and the rough machining of an aircraft engine blisk are carried out to test the effectiveness and practicability of the proposed model. The results indicate that it is essential to take into account the bottom edge cutting effect for accurate prediction of cutting forces at tool path zones where the tool bottom part engages with the workpiece.


  • Envelope Surface Modeling and Tool Path Optimization for Five-Axis Flank Milling Considering Cutter Runout

    by Zhou-Long Li, Li-Min Zhu

    Cutter runout is a common and inevitable phenomenon impacting the geometry accuracy in the milling process. However, most of the works on tool path planning neglect the cutter runout effect. In this paper, a new approach is presented to integrate the cutter runout effect into envelope surface modeling and tool path optimization for five-axis flank milling with a conical cutter. Based on the geometry model of cutter runout which consists of cutter axis and cutter tilt, an analytic expression of cutter edge combined with four runout parameters is derived. Then the envelope surface formed by each cutter edge is constructed using the envelope theory of sphere congruence. Due to the cutter runout effect, the envelope surfaces formed by the cutter edges are different from each other, and the valid envelope surface is the combination of these envelope surfaces which contribute to the final machined surface. To measure the machining errors, the geometry deviations between the valid envelope surface and the design surface are calculated with the distance function. On the basis of the differential property of the distance function, tool path optimization considering cutter runout is modeled as a mixed-integer linear programming (MILP) problem, which can be solved by the branch-and-bound method. Finally, numerical examples are given to confirm the validity and efficiency of the proposed approach. The results show that the geometry errors induced by runout can be reduced significantly using the proposed method.


  • Constrained Ruled Surface Reconstruction for 5-Axis NC Machining of Aero-Structure

    by Qing Zhen Bi, Yao An Lu, Zhou Long Li, Li Min Zhu, Han Ding, Gang Liu

    We proposed a constrained ruled surface approximation algorithm for 5-axis machining of aero structure. Ruled surface is widely used in the design of aero structure. In practical model process, the regular ruled surface is usually split into some small fragmentary surfaces. The segmentation of the original surface mainly comes from some iterative boolean operations on the ruled surface. The segmentation destroys original parameter lines and leads into complex curved boundaries. Furthermore, the obtained fragmentary surfaces deviate from the original ruled surface because of the accuracy loss in the boolean operations of 3D CAD software. Some gaps between the small surfaces often appear. In manufacturing process, it is difficult to generating high-quality tool path for the surface with disordered parameter lines, curved boundaries and gaps. The proposed ruled surface approximation algorithm provides an effective way to reconstruct the smooth ruled surface. The constraints of boundary and smoothness are both considered. The ruled surface for simultaneous 5-axis machining is finally obtained. This algorithm have been integrated into CATIA V5 system and applied in practical manufacturing planning of aero-structures.