Peter Pira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Peter Pira has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Libor Juha
Department of Radiation and Chemical Physics, Institute of Physics, Czech Academy of Sciences 2 , Na Slovance 2, 18221 Prague
7 shared publications - Jan Wild
Charles University
6 shared publications - Luděk Vyšín
Department of Radiation and Chemical Physics, Institute of Physics, Czech Academy of Sciences 1 , Na Slovance 2, 18200 Prague 8
5 shared publications - Tomas Burian
Department of Radiation and Chemical Physics, Institute of Physics, Czech Academy of Sciences 1 , Na Slovance 2, 18200 Prague 8
5 shared publications Jakub Dlabka
Faculty of Safety Engineering, VŠB-Technical University of Ostrava, Lumírova 13, Ostrava-Výškovice, CZ 700 30, Czech Republic
3 shared publications- Michal Dostál
Faculty of Safety Engineering, VSB–Technical University of Ostrava, Lumírova 630/13, 700 30 Ostrava, Czech Republic
3 shared publications
Latest Publications
- Open Access
- 23 October 2020
- Published by Walter de Gruyter GmbH in Nukleonika
- Vol. 65 (4) , 205-210
Ablation of single-crystalline cesium iodide by extreme ultraviolet capillary-discharge laser
Extreme ultraviolet (XUV) capillary-discharge lasers (CDLs) are a suitable source for the efficient, clean ablation of ionic crystals, which are obviously difficult to ablate with conventional, long-wavelength lasers. In the present study, a single crystal of cesium iodide (CsI) was irradiated by multiple, focused 1.5-ns pulses of 46.9-nm radiation delivered from a compact XUV-CDL device operated at either 2-Hz or 3-Hz repetition rates. The ablation rates were determined from the depth of the craters produced by the accumulation of laser pulses. Langmuir probes were used to diagnose the plasma plume produced by the focused XUV-CDL beam. Both the electron density and electron temperature were sufficiently high to confirm that ablation was the key process in the observed CsI removal. Moreover, a CsI thin film on MgO substrate was prepared by XUV pulsed laser deposition; a fraction of the film was detected by X-ray photoelectron spectroscopy.
- 23 October 2020
- Published by Walter de Gruyter GmbH in Nukleonika
- Vol. 65 (4) , 205-210
Open AccessAblation of single-crystalline cesium iodide by extreme ultraviolet capillary-discharge laser
Extreme ultraviolet (XUV) capillary-discharge lasers (CDLs) are a suitable source for the efficient, clean ablation of ionic crystals, which are obviously difficult to ablate with conventional, long-wavelength lasers. In the present study, a single crystal of cesium iodide (CsI) was irradiated by multiple, focused 1.5-ns pulses of 46.9-nm radiation delivered from a compact XUV-CDL device operated at either 2-Hz or 3-Hz repetition rates. The ablation rates were determined from the depth of the craters produced by the accumulation of laser pulses. Langmuir probes were used to diagnose the plasma plume produced by the focused XUV-CDL beam. Both the electron density and electron temperature were sufficiently high to confirm that ablation was the key process in the observed CsI removal. Moreover, a CsI thin film on MgO substrate was prepared by XUV pulsed laser deposition; a fraction of the film was detected by X-ray photoelectron spectroscopy.
- Open Access
- 1 June 2016
- Published by Walter de Gruyter GmbH in Nukleonika
- Vol. 61 (2) , 131-138
Desorption/ablation of lithium fluoride induced by extreme ultraviolet laser radiation
The availability of reliable modeling tools and input data required for the prediction of surface removal rate from the lithium fluoride targets irradiated by the intense photon beams is essential for many practical aspects. This study is motivated by the practical implementation of soft X-ray (SXR) or extreme ultraviolet (XUV) lasers for the pulsed ablation and thin film deposition. Specifically, it is focused on quantitative description of XUV laser-induced desorption/ablation from lithium fluoride, which is a reference large band-gap dielectric material with ionic crystalline structure. Computational framework was proposed and employed here for the reconstruction of plume expansion dynamics induced by the irradiation of lithium fluoride targets. The morphology of experimentally observed desorption/ablation craters were reproduced using idealized representation (two-zone approximation) of the laser fluence profile. The calculation of desorption/ablation rate was performed using one-dimensional thermomechanic model (XUV-ABLATOR code) taking into account laser heating and surface evaporation of the lithium fluoride target occurring on a nanosecond timescale. This step was followed by the application of two-dimensional hydrodynamic solver for description of laser-produced plasma plume expansion dynamics. The calculated plume lengths determined by numerical simulations were compared with a simple adiabatic expansion (blast-wave) model.
- 1 June 2016
- Published by Walter de Gruyter GmbH in Nukleonika
- Vol. 61 (2) , 131-138
Open AccessDesorption/ablation of lithium fluoride induced by extreme ultraviolet laser radiation
The availability of reliable modeling tools and input data required for the prediction of surface removal rate from the lithium fluoride targets irradiated by the intense photon beams is essential for many practical aspects. This study is motivated by the practical implementation of soft X-ray (SXR) or extreme ultraviolet (XUV) lasers for the pulsed ablation and thin film deposition. Specifically, it is focused on quantitative description of XUV laser-induced desorption/ablation from lithium fluoride, which is a reference large band-gap dielectric material with ionic crystalline structure. Computational framework was proposed and employed here for the reconstruction of plume expansion dynamics induced by the irradiation of lithium fluoride targets. The morphology of experimentally observed desorption/ablation craters were reproduced using idealized representation (two-zone approximation) of the laser fluence profile. The calculation of desorption/ablation rate was performed using one-dimensional thermomechanic model (XUV-ABLATOR code) taking into account laser heating and surface evaporation of the lithium fluoride target occurring on a nanosecond timescale. This step was followed by the application of two-dimensional hydrodynamic solver for description of laser-produced plasma plume expansion dynamics. The calculated plume lengths determined by numerical simulations were compared with a simple adiabatic expansion (blast-wave) model.
- 12 May 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9511, 95110K-95110K-9
Material properties of lithium fluoride for predicting XUV laser ablation rate and threshold fluence
- 12 May 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9511, 95110K-95110K-9
Material properties of lithium fluoride for predicting XUV laser ablation rate and threshold fluence
- 5 September 2014
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 47 (40)
Langmuir probe measurement of the bismuth plasma plume formed by an extreme-ultraviolet pulsed laser
- 5 September 2014
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 47 (40)
Langmuir probe measurement of the bismuth plasma plume formed by an extreme-ultraviolet pulsed laser
- 3 May 2013
- Published by SPIE-Intl Soc Optical Eng
- p. 87770C-87770C-8
Global sensitivity analysis of the XUV-ABLATOR code
- 3 May 2013
- Published by SPIE-Intl Soc Optical Eng
- p. 87770C-87770C-8
Global sensitivity analysis of the XUV-ABLATOR code
- 5 May 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8077, 807719
Ablation of ionic crystals induced by capillary-discharge XUV laser
Single crystals of two fluorides (LiF and CaF2) and a tungstate (PbWO4) were irradiated by nanosecond pulses of 46.9- nm radiation provided by 10-Hz capillary-discharge Ne-like Ar laser (CDL). The damage threshold was determined in LiF using the CDL beam focused by a Sc/Si multilayer-coated spherical mirror. Irradiated samples have been investigated by Nomarski (DIC - Differential Interference Contrast) microscopy and optical (WLI - white light intereferometry) profiler. After an exposure by a certain number of CDL pulses, an ablation rate can be calculated from WLI measured depth of the crater created by the XUV ablation. Potential use of XUV ablation of ionic crystals in pulsed laser deposition (PLD) of thin layers of such a particular material, which is difficult to ablate by conventional UV-Vis- NIR lasers, is discussed in this contribution.
- 5 May 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8077, 807719
Ablation of ionic crystals induced by capillary-discharge XUV laser
Single crystals of two fluorides (LiF and CaF2) and a tungstate (PbWO4) were irradiated by nanosecond pulses of 46.9- nm radiation provided by 10-Hz capillary-discharge Ne-like Ar laser (CDL). The damage threshold was determined in LiF using the CDL beam focused by a Sc/Si multilayer-coated spherical mirror. Irradiated samples have been investigated by Nomarski (DIC - Differential Interference Contrast) microscopy and optical (WLI - white light intereferometry) profiler. After an exposure by a certain number of CDL pulses, an ablation rate can be calculated from WLI measured depth of the crater created by the XUV ablation. Potential use of XUV ablation of ionic crystals in pulsed laser deposition (PLD) of thin layers of such a particular material, which is difficult to ablate by conventional UV-Vis- NIR lasers, is discussed in this contribution.
- 7 May 2009
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7361, 73610O
Characterization of focused beam of desktop 10-Hz capillary-discharge 46.9-nm laser
The desktop capillary-discharge Ne-like Ar laser (CDL) providing 10-μJ nanosecond pulses of coherent 46.9-nm radiation with a repetition rate up to 12 Hz was developed and built at the Colorado State University in Fort Collins and then installed in Prague. The beam of the laser was focused by a spherical mirror covered with Si/Sc multilayer coating onto the surface of poly(methyl methacrylate) - PMMA. Interaction parameters vary by changing the distance between sample surface and beam focus. The samples were exposed to various numbers of shots. Analysis of damaged PMMA by atomic force (AFM) and Nomarski (DIC - differential interference contrast) microscopes allows not only to determine the key characteristics of the focused beam (e.g. Rayleigh's parameter, focal spot diameter, tight focus position, etc.) but also to investigate mechanisms of the radiation-induced erosion processes.
- 7 May 2009
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7361, 73610O
Characterization of focused beam of desktop 10-Hz capillary-discharge 46.9-nm laser
The desktop capillary-discharge Ne-like Ar laser (CDL) providing 10-μJ nanosecond pulses of coherent 46.9-nm radiation with a repetition rate up to 12 Hz was developed and built at the Colorado State University in Fort Collins and then installed in Prague. The beam of the laser was focused by a spherical mirror covered with Si/Sc multilayer coating onto the surface of poly(methyl methacrylate) - PMMA. Interaction parameters vary by changing the distance between sample surface and beam focus. The samples were exposed to various numbers of shots. Analysis of damaged PMMA by atomic force (AFM) and Nomarski (DIC - differential interference contrast) microscopes allows not only to determine the key characteristics of the focused beam (e.g. Rayleigh's parameter, focal spot diameter, tight focus position, etc.) but also to investigate mechanisms of the radiation-induced erosion processes.