Takahiro Hayashi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Takahiro Hayashi has a total of 202 co-authors. Here are the top co-authors by number of shared publications:
Koichiro Kawashima
Ultrasonic Materials Diagnosis Lab
17 shared publicationsMorimasa Murase
Toyota Central R&D Labs., Inc
13 shared publications- Naoki Mori
The University of Osaka
12 shared publications - Naoki Ikegaya
Department of Neurosurgery, Graduate School of Medicine, Yokohama City University, Yokohama, Japan
11 shared publications - Akihide Ryo
Department of Bioinformatics and Integrative Omics, National Institute of Infectious Diseases, Japan Institute for Health Security, Japan
10 shared publications - Akito Oshima
Department of Neurosurgery, Graduate School of Medicine, Yokohama City University, Yokohama, Japan
10 shared publications
Latest Publications
- 21 July 2026
- Published by Taylor & Francis in Nondestructive Testing and Evaluation
- p. 1-22
Remote detection of clogging in thin pipes using laser-generated ultrasound
1. Industrial plants contain an enormous number of pipes, and inspecting them is a critical task for ensuring plant safety and improving operational efficiency. Many plants perform wall thickness i...
- 21 July 2026
- Published by Taylor & Francis in Nondestructive Testing and Evaluation
- p. 1-22
Remote detection of clogging in thin pipes using laser-generated ultrasound
1. Industrial plants contain an enormous number of pipes, and inspecting them is a critical task for ensuring plant safety and improving operational efficiency. Many plants perform wall thickness i...
- 4 July 2026
- Published by Elsevier in Ultrasonics
- Vol. 168, 108203
Underwater surface profiling using laser generated ultrasound
- 4 July 2026
- Published by Elsevier in Ultrasonics
- Vol. 168, 108203
Underwater surface profiling using laser generated ultrasound
- 4 June 2026
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 63 (10) , 1-8
Development of radiation-resistant ultrasonic sensor unit
1. Decommissioning work at the Fukushima Daiichi Nuclear Power Station (FDNPS) accident site is currently in progress; however, many challenges and difficulties in removing fuel debris still remain...
- 4 June 2026
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 63 (10) , 1-8
Development of radiation-resistant ultrasonic sensor unit
1. Decommissioning work at the Fukushima Daiichi Nuclear Power Station (FDNPS) accident site is currently in progress; however, many challenges and difficulties in removing fuel debris still remain...
- Open Access
- 1 January 2026
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE ESS Fundamentals Review
- Vol. 19 (3) , 139-145
Non-Destructive Testing Using Laser Generated Ultrasonic
レーザにより超音波を励振し,超音波を検出するという非接触の超音波送受信方法はレーザ超音波法と呼ばれ,固体材料の非破壊検査に利用されている.しかし,非破壊検査ではユーザがもつ対象物に合わせてカスタマイズが必要になることが多く,そのためにはレーザ超音波法の仕組みを知ることが重要である.著者らは特に,超音波の励振技術に特徴のある研究を進め,新しい非破壊検査法を提案している.そこで本報では,はじめにレーザにより超音波が発生する原理と発生する超音波の制御方法について述べ,配管検査及び三次元積層造形体の検査に対し,これまで著者らが進めてきた研究を紹介している.
- 1 January 2026
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE ESS Fundamentals Review
- Vol. 19 (3) , 139-145
Open AccessNon-Destructive Testing Using Laser Generated Ultrasonic
レーザにより超音波を励振し,超音波を検出するという非接触の超音波送受信方法はレーザ超音波法と呼ばれ,固体材料の非破壊検査に利用されている.しかし,非破壊検査ではユーザがもつ対象物に合わせてカスタマイズが必要になることが多く,そのためにはレーザ超音波法の仕組みを知ることが重要である.著者らは特に,超音波の励振技術に特徴のある研究を進め,新しい非破壊検査法を提案している.そこで本報では,はじめにレーザにより超音波が発生する原理と発生する超音波の制御方法について述べ,配管検査及び三次元積層造形体の検査に対し,これまで著者らが進めてきた研究を紹介している.
- Open Access
- 9 October 2025
- Published by Elsevier in NDT & E International
- Vol. 158
Ultrasonic imaging using a phased array probe with a buffer consisting of a bundle of circular cylinders
- 9 October 2025
- Published by Elsevier in NDT & E International
- Vol. 158
Open AccessUltrasonic imaging using a phased array probe with a buffer consisting of a bundle of circular cylinders
- 21 April 2025
- Published by SAGE Publications in Structural Health Monitoring
Polymer coating characterization based on ultrasonic interference and critical attenuation
A characterization technique is proposed for polymer coating structures immersed in water based on the ultrasonic interference and critical attenuation phenomenon. When a coating layer is modeled as a linear viscoelastic material and is subjected to the normal incidence of an ultrasonic wave, the theoretical analysis shows that the reflection spectrum takes local minima at multiple frequencies, which correspond to the resonance frequencies of the coating layer depending on the wave velocity and the thickness under the assumption of relatively low loss factors. Furthermore, the lower envelope of the reflection spectrum yields the critical attenuation condition, which is closely related to the loss factor of the coating. These theoretical findings are applied to the viscoelastic characterization of the coating layers. Two bonded specimens with different substrate thicknesses validate the proposed method. As a result, the experimental data demonstrate that the estimated wave velocities and loss factors of the coatings agree well with the results reported in the previous paper. After the experimental validation, the proposed method is applied to the curing monitoring of a resin coating on a metal substrate. The ultrasonic responses provide the temporal variation of the layer resonance frequencies and the critical attenuation frequency by the resin curing. These results can be used to estimate the viscoelastic properties of the coating, which imply the curing state of the resin.
- 21 April 2025
- Published by SAGE Publications in Structural Health Monitoring
Polymer coating characterization based on ultrasonic interference and critical attenuation
A characterization technique is proposed for polymer coating structures immersed in water based on the ultrasonic interference and critical attenuation phenomenon. When a coating layer is modeled as a linear viscoelastic material and is subjected to the normal incidence of an ultrasonic wave, the theoretical analysis shows that the reflection spectrum takes local minima at multiple frequencies, which correspond to the resonance frequencies of the coating layer depending on the wave velocity and the thickness under the assumption of relatively low loss factors. Furthermore, the lower envelope of the reflection spectrum yields the critical attenuation condition, which is closely related to the loss factor of the coating. These theoretical findings are applied to the viscoelastic characterization of the coating layers. Two bonded specimens with different substrate thicknesses validate the proposed method. As a result, the experimental data demonstrate that the estimated wave velocities and loss factors of the coatings agree well with the results reported in the previous paper. After the experimental validation, the proposed method is applied to the curing monitoring of a resin coating on a metal substrate. The ultrasonic responses provide the temporal variation of the layer resonance frequencies and the critical attenuation frequency by the resin curing. These results can be used to estimate the viscoelastic properties of the coating, which imply the curing state of the resin.
- Open Access
- 16 December 2024
- Published by Elsevier in NDT & E International
- Vol. 151
Experimental investigation of defect imaging using a phased array probe with a stacked plate buffer
- 16 December 2024
- Published by Elsevier in NDT & E International
- Vol. 151
Open AccessExperimental investigation of defect imaging using a phased array probe with a stacked plate buffer
- 22 November 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (1) , 015605
Curing monitoring of adhesive layers between metal adherends by ultrasonic resonance technique
Layer resonance induced by ultrasonic wave incidence is applied to monitor the viscoelastic properties of a curing adhesive layer between metal plates. A theoretical analysis shows that when the adhesive layer is modeled as a linear viscoelastic material, the ultrasonic reflection spectrum takes local minima at the layer resonance frequencies depending on the wave velocity of the adhesive. In contrast, the local minima of the reflection spectrum can be expressed as a function of the loss factor of the adhesive. Based on these results, a characterization technique for the wave velocity and the loss factor of a curing adhesive layer is proposed. This technique enables the evaluation of viscoelastic properties even if the reflected waves from both faces of a bond layer cannot be separated. The proposed method is used to investigate the curing behavior of bi-component epoxy adhesives. It is shown that the bonding condition affects the variation of the wave velocity and loss factor. The estimated wave velocity increases as the curing proceeds, whereas the loss factor sometimes takes a local maximum depending on the bonding condition and the frequency range. When the mixing ratio of the main and curing agents is imbalanced, the variation of the wave velocity becomes gradual. Furthermore, the increase in the curing temperature leads to fast changes in the wave velocity and loss factor. The proposed technique has the potential to provide insights into the curing behavior of the adhesive layer by incorporating it into other measurement methods and theories.
- 22 November 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (1) , 015605
Curing monitoring of adhesive layers between metal adherends by ultrasonic resonance technique
Layer resonance induced by ultrasonic wave incidence is applied to monitor the viscoelastic properties of a curing adhesive layer between metal plates. A theoretical analysis shows that when the adhesive layer is modeled as a linear viscoelastic material, the ultrasonic reflection spectrum takes local minima at the layer resonance frequencies depending on the wave velocity of the adhesive. In contrast, the local minima of the reflection spectrum can be expressed as a function of the loss factor of the adhesive. Based on these results, a characterization technique for the wave velocity and the loss factor of a curing adhesive layer is proposed. This technique enables the evaluation of viscoelastic properties even if the reflected waves from both faces of a bond layer cannot be separated. The proposed method is used to investigate the curing behavior of bi-component epoxy adhesives. It is shown that the bonding condition affects the variation of the wave velocity and loss factor. The estimated wave velocity increases as the curing proceeds, whereas the loss factor sometimes takes a local maximum depending on the bonding condition and the frequency range. When the mixing ratio of the main and curing agents is imbalanced, the variation of the wave velocity becomes gradual. Furthermore, the increase in the curing temperature leads to fast changes in the wave velocity and loss factor. The proposed technique has the potential to provide insights into the curing behavior of the adhesive layer by incorporating it into other measurement methods and theories.
- Open Access
- 3 September 2024
- Published by Elsevier in International Journal of Pressure Vessels and Piping
- Vol. 212
Detection of deposits adhered on the back surface of plate-like structures using a scanning laser source technique
- 3 September 2024
- Published by Elsevier in International Journal of Pressure Vessels and Piping
- Vol. 212
Open AccessDetection of deposits adhered on the back surface of plate-like structures using a scanning laser source technique
- 1 July 2024
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 156 (1) , 44-54
Tunable elastic wave transmission and resonance in a periodically aligned tube-block structure
A tube-block structure is proposed to realize tunable elastic wave transmission and resonance, consisting of periodically aligned circular tubes sandwiched and joined by two blocks. Finite element simulations for a unit structure are carried out to reveal the frequency dependence of the transmission behavior for the normal incidence of longitudinal and transverse waves in the tube-block structure. As a result, the transmission ratios are found to take multiple local maxima at different peak frequencies. Eigenfrequency analysis shows that the local resonances of the tube and the block surfaces occur at the peak frequencies in the transmission ratios. The peak frequencies originating from the local resonance of the tube depend on its radius and thickness, while those from the resonance on the block surfaces are in good agreement with the theoretical relation between the interval of the periodically aligned tubes and the wavelength of the Rayleigh wave. Furthermore, when the tube-block structure is subjected to compressive loading, the deformation shifts the peak frequencies of the transmission ratio corresponding to the local resonance of the tube. This result implies that the proposed structure has the potential to serve as a tunable meta-interface between solid blocks.
- 1 July 2024
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 156 (1) , 44-54
Tunable elastic wave transmission and resonance in a periodically aligned tube-block structure
A tube-block structure is proposed to realize tunable elastic wave transmission and resonance, consisting of periodically aligned circular tubes sandwiched and joined by two blocks. Finite element simulations for a unit structure are carried out to reveal the frequency dependence of the transmission behavior for the normal incidence of longitudinal and transverse waves in the tube-block structure. As a result, the transmission ratios are found to take multiple local maxima at different peak frequencies. Eigenfrequency analysis shows that the local resonances of the tube and the block surfaces occur at the peak frequencies in the transmission ratios. The peak frequencies originating from the local resonance of the tube depend on its radius and thickness, while those from the resonance on the block surfaces are in good agreement with the theoretical relation between the interval of the periodically aligned tubes and the wavelength of the Rayleigh wave. Furthermore, when the tube-block structure is subjected to compressive loading, the deformation shifts the peak frequencies of the transmission ratio corresponding to the local resonance of the tube. This result implies that the proposed structure has the potential to serve as a tunable meta-interface between solid blocks.