Muhammad Sigit Darmawan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Muhammad Sigit Darmawan has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Ridho Bayuaji
Department of Civil Infrastructure Engineering, Faculty of Vocations, Institut Teknologi Sepuluh Nopember, Surabaya 60111, Indonesia
6 shared publications Boedi Wibowo
Institut Teknologi Sepuluh Nopember Civil Engineering Department Surabaya Indonesia
3 shared publicationsNur Ahmad Husin
Institut Teknologi Sepuluh Nopember
3 shared publicationsSrie Subekti
Institut Teknologi Sepuluh Nopember Civil Engineering Department Surabaya Indonesia
3 shared publicationsR.B. Anugraha
2 shared publicationsA. Budipriyanto
1 shared publication
Latest Publications
- Open Access
Shear Strength of Geopolymer Concrete Beams Using High Calcium Content Fly Ash in a Marine Environment
This paper deals with the behavior of a geopolymer concrete beam (GCB) under shear load using high calcium content fly ash (FA). The effect of the marine environment on the shear strength of GCB was considered by curing the specimen in a sea splashing zone for 28 days. Destructive and non-destructive tests were carried out to determine the properties of geopolymer concrete in different curing environments. Geopolymer concretes cured at room temperature showed higher compressive strength, slightly lower porosity, and higher concrete resistivity than that of those cured in sea water. From the loading test of the GCB under shear load, there was no effect of a sea environment on the crack pattern and crack development of the beam. The shear strength of the GCB generally exceeded the predicted shear strength based on the American Concrete Institute (ACI) Code.
Open AccessShear Strength of Geopolymer Concrete Beams Using High Calcium Content Fly Ash in a Marine Environment
This paper deals with the behavior of a geopolymer concrete beam (GCB) under shear load using high calcium content fly ash (FA). The effect of the marine environment on the shear strength of GCB was considered by curing the specimen in a sea splashing zone for 28 days. Destructive and non-destructive tests were carried out to determine the properties of geopolymer concrete in different curing environments. Geopolymer concretes cured at room temperature showed higher compressive strength, slightly lower porosity, and higher concrete resistivity than that of those cured in sea water. From the loading test of the GCB under shear load, there was no effect of a sea environment on the crack pattern and crack development of the beam. The shear strength of the GCB generally exceeded the predicted shear strength based on the American Concrete Institute (ACI) Code.
- 1 February 2018
- Published by Elsevier in Engineering Failure Analysis
- Vol. 84, 287-299
Corrosion damage assessment of a reinforced concrete canal structure of power plant after 20 years of exposure in a marine environment: A case study
- 1 February 2018
- Published by Elsevier in Engineering Failure Analysis
- Vol. 84, 287-299
Corrosion damage assessment of a reinforced concrete canal structure of power plant after 20 years of exposure in a marine environment: A case study
- Open Access
- 30 November 2016
- Published by Bentham Science Publishers Ltd. in The Open Civil Engineering Journal
- Vol. 10 (1) , 782-793
Utilization of High Calcium Content Fly Ash: Flexural Strength of Geopolymer Concrete Beams in Sea Water Environment
This paper presents a study of the flexural strength of geopolymer concrete beam using high calcium content fly ash (FA) in marine environment, without high heat curing. Two series of beam specimens were loaded to failure to study the effect of chloride environment on the flexural strength of geopolymer concrete beams. Series I specimens were subjected to sea environment, whereas series II were kept at room temperature. Tests performed on concrete cylinders show that the sea water has no effect on compressive and splitting tensile stress of high calcium content FA based geopolymer concrete. However, the ratio of splitting and compressive strength for both series was approximately 44%, almost double than that of normal concrete. In addition, the flexural test of concrete beams shows that the average cracking load for series I specimens was 275% higher than that of series II. However, the ultimate load, crack pattern and deflection characteristic for both series were very similar.
- 30 November 2016
- Published by Bentham Science Publishers Ltd. in The Open Civil Engineering Journal
- Vol. 10 (1) , 782-793
Open AccessUtilization of High Calcium Content Fly Ash: Flexural Strength of Geopolymer Concrete Beams in Sea Water Environment
This paper presents a study of the flexural strength of geopolymer concrete beam using high calcium content fly ash (FA) in marine environment, without high heat curing. Two series of beam specimens were loaded to failure to study the effect of chloride environment on the flexural strength of geopolymer concrete beams. Series I specimens were subjected to sea environment, whereas series II were kept at room temperature. Tests performed on concrete cylinders show that the sea water has no effect on compressive and splitting tensile stress of high calcium content FA based geopolymer concrete. However, the ratio of splitting and compressive strength for both series was approximately 44%, almost double than that of normal concrete. In addition, the flexural test of concrete beams shows that the average cracking load for series I specimens was 275% higher than that of series II. However, the ultimate load, crack pattern and deflection characteristic for both series were very similar.
- 20 April 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 754-755, 400-405
The Influence of Chloride Environment on Compressive Strength of Geopolymer Concrete with Fly Ash Using Taguchi Approach
This study is conducted to determine the effect of four variables on compressive strength of geopolymer concretes. These four variables are binder/aggregate, Alkalinene/fly ash, effect of superplasticizer (SP) addition and curing system. The compressive strength is important mechanical properties for construction material. Taguchi experimental design method is used to compile the concrete composition of geopolymer to achieve the maximum compressive strength. Specimens concrete used is a cylinder with 100 mm diameter and 200 mm height. Compressive strength test is performed at 28 day using SNI 03-6825-2002, Indonesian National Standard. This study concludes that the chloride environment has a beneficial effect on the compressive strength of the concrete. In addition, the Alkalinene/fly ash ratio and binder/aggregate give a significant effect on the compressive strength of geopolymer concretes.
- 20 April 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 754-755, 400-405
The Influence of Chloride Environment on Compressive Strength of Geopolymer Concrete with Fly Ash Using Taguchi Approach
This study is conducted to determine the effect of four variables on compressive strength of geopolymer concretes. These four variables are binder/aggregate, Alkalinene/fly ash, effect of superplasticizer (SP) addition and curing system. The compressive strength is important mechanical properties for construction material. Taguchi experimental design method is used to compile the concrete composition of geopolymer to achieve the maximum compressive strength. Specimens concrete used is a cylinder with 100 mm diameter and 200 mm height. Compressive strength test is performed at 28 day using SNI 03-6825-2002, Indonesian National Standard. This study concludes that the chloride environment has a beneficial effect on the compressive strength of the concrete. In addition, the Alkalinene/fly ash ratio and binder/aggregate give a significant effect on the compressive strength of geopolymer concretes.
- Open Access
- 1 January 2015
- Published by Elsevier in Procedia Engineering
- Vol. 125, 579-586
A Case Study of Low Compressive Strength of Concrete Containing Fly Ash in East Java Indonesia
- 1 January 2015
- Published by Elsevier in Procedia Engineering
- Vol. 125, 579-586
Open AccessA Case Study of Low Compressive Strength of Concrete Containing Fly Ash in East Java Indonesia
- Open Access
- 11 November 2014
- Published by Hindawi Limited in Advances in Civil Engineering
- Vol. 2014, 1-16
Case Study of Remaining Service Life Assessment of a Cooling Water Intake Concrete Structure in Indonesia
This paper deals with the assessment of remaining service life of a cooling water intake concrete structure (CWICS) subjected to corrosion due to chloride attacks. Field and laboratory tests were performed to determine the current existing condition of the structure. Both destructive and nondestructive tests were employed to obtain the parameter needed for the assessment. Based on the current condition and test results, structural analysis was carried out and the remaining safety factor of CWICS was determined. From the analysis, it was found that most concrete elements of CWICS had safety factor greater than unity and might fulfil its intended service life up to the year 2033. However, fewer elements require immediate strengthening to extend their service life.
- 11 November 2014
- Published by Hindawi Limited in Advances in Civil Engineering
- Vol. 2014, 1-16
Open AccessCase Study of Remaining Service Life Assessment of a Cooling Water Intake Concrete Structure in Indonesia
This paper deals with the assessment of remaining service life of a cooling water intake concrete structure (CWICS) subjected to corrosion due to chloride attacks. Field and laboratory tests were performed to determine the current existing condition of the structure. Both destructive and nondestructive tests were employed to obtain the parameter needed for the assessment. Based on the current condition and test results, structural analysis was carried out and the remaining safety factor of CWICS was determined. From the analysis, it was found that most concrete elements of CWICS had safety factor greater than unity and might fulfil its intended service life up to the year 2033. However, fewer elements require immediate strengthening to extend their service life.
- Open Access
- 31 December 2013
- Published by Elsevier in Procedia Engineering
- Vol. 54, 270-285
Time Dependent Reliability Analysis of Steel I Bridge Girder Designed Based on SNI T-02-2005 and SNI T-3-2005 Subjected to Corrosion
- 31 December 2013
- Published by Elsevier in Procedia Engineering
- Vol. 54, 270-285
Open AccessTime Dependent Reliability Analysis of Steel I Bridge Girder Designed Based on SNI T-02-2005 and SNI T-3-2005 Subjected to Corrosion
- 1 December 2013
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 594-595, 648-655
The Effect of Chloride Environment on Mechanical Properties Geopolymer Binder with Fly Ash
This study is conducted to determine the effect of five variables on mechanical properties of geopolymer binders. These five variables are chloride environment, NaOH molarity, Na2SiO3/NaOH ratio, fly ash/alkaline activator (FA/AA) ratio and superplasticizer (SP) addition. The mechanical properties considered are compressive strength, porosity and density. Taguchi experimental design method is used to compile the binder composition of geopolymer to achieve the maximum compressive strength. Specimens binder used is a cylinder with 25 mm diameter and 50 mm height. Compressive strength test is performed at 28 days using SNI 03-6825-2002 (Indonesian National Standard) and porosity of the binder is determined using vacuum saturation apparatus similar to that developed by RILEM. The density of the binder is measured using Ultrasonic Pulse Velocity (UPV). This study concludes that the chloride environment has a beneficial effect on the compressive strength of the binder. In addition, the FA/AA ratio and NaOH molarity give a significant effect on the compressive strength of geopolymer binders.
- 1 December 2013
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 594-595, 648-655
The Effect of Chloride Environment on Mechanical Properties Geopolymer Binder with Fly Ash
This study is conducted to determine the effect of five variables on mechanical properties of geopolymer binders. These five variables are chloride environment, NaOH molarity, Na2SiO3/NaOH ratio, fly ash/alkaline activator (FA/AA) ratio and superplasticizer (SP) addition. The mechanical properties considered are compressive strength, porosity and density. Taguchi experimental design method is used to compile the binder composition of geopolymer to achieve the maximum compressive strength. Specimens binder used is a cylinder with 25 mm diameter and 50 mm height. Compressive strength test is performed at 28 days using SNI 03-6825-2002 (Indonesian National Standard) and porosity of the binder is determined using vacuum saturation apparatus similar to that developed by RILEM. The density of the binder is measured using Ultrasonic Pulse Velocity (UPV). This study concludes that the chloride environment has a beneficial effect on the compressive strength of the binder. In addition, the FA/AA ratio and NaOH molarity give a significant effect on the compressive strength of geopolymer binders.
- 1 February 2010
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 62 (2) , 91-101
Pitting corrosion model for reinforced concrete structures in a chloride environment
Different types of corrosion may arise in steel reinforcement, such as general corrosion, pitting corrosion, hydrogen embrittlement, stress corrosion cracking and corrosion fatigue. However, corrosion of steel reinforcement in reinforced concrete (RC) structures can be classified into two categories: general (uniform) corrosion and pitting (localised) corrosion. In general, concrete researchers use uniform corrosion to study the effect of corrosion on RC structures. This approach is not accurate for concrete structures subjected to chloride attack, which usually experiences pitting corrosion. This paper describes an accelerated corrosion test used to obtain statistical parameters of maximum pit-depths distribution of corroded steel in a RC structure. Using probabilistic analysis, these statistical parameters are combined with statistical parameters of RC beams (i.e. beam dimensions, concrete strength, steel yield strength, cover thickness, workmanship quality, in situ strength factor, model error for flexure and shear and also corrosion rate) to determine the effect of corrosion on flexural and shear strength of RC beams. Using the proposed pitting corrosion model improves service life prediction of RC structures in a chloride environment.
- 1 February 2010
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 62 (2) , 91-101
Pitting corrosion model for reinforced concrete structures in a chloride environment
Different types of corrosion may arise in steel reinforcement, such as general corrosion, pitting corrosion, hydrogen embrittlement, stress corrosion cracking and corrosion fatigue. However, corrosion of steel reinforcement in reinforced concrete (RC) structures can be classified into two categories: general (uniform) corrosion and pitting (localised) corrosion. In general, concrete researchers use uniform corrosion to study the effect of corrosion on RC structures. This approach is not accurate for concrete structures subjected to chloride attack, which usually experiences pitting corrosion. This paper describes an accelerated corrosion test used to obtain statistical parameters of maximum pit-depths distribution of corroded steel in a RC structure. Using probabilistic analysis, these statistical parameters are combined with statistical parameters of RC beams (i.e. beam dimensions, concrete strength, steel yield strength, cover thickness, workmanship quality, in situ strength factor, model error for flexure and shear and also corrosion rate) to determine the effect of corrosion on flexural and shear strength of RC beams. Using the proposed pitting corrosion model improves service life prediction of RC structures in a chloride environment.
- Open Access
- 1 August 2009
- Published by Lembaga Penelitian dan Pengabdian kepada Masyarakat ITS in Jurnal Aplikasi Teknik Sipil
- Vol. 7 (1) , 20
Kemungkinan Terjadinya Retak pada Balok Pratekan Full Prestressing
Kemungkinan Terjadinya Retak pada Balok Pratekan Full Prestressing
- 1 August 2009
- Published by Lembaga Penelitian dan Pengabdian kepada Masyarakat ITS in Jurnal Aplikasi Teknik Sipil
- Vol. 7 (1) , 20
Open AccessKemungkinan Terjadinya Retak pada Balok Pratekan Full Prestressing
Kemungkinan Terjadinya Retak pada Balok Pratekan Full Prestressing