Alexandre Martin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Alexandre Martin has a total of 131 co-authors. Here are the top co-authors by number of shared publications:
Haoyue Weng
University of Kentucky, Lexington, Kentucky 40506
15 shared publicationsIain Boyd
University of Michigan, Ann Arbor
11 shared publicationsFrancesco Panerai
9 shared publicationsIain D. Boyd
Department of Aerospace Engineering, University of Michigan, Ann Arbor, Michigan 48109
8 shared publicationsNagi N. Mansour
7 shared publicationsHuaibao Zhang
6 shared publications
Latest Publications
- 1 September 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 63 (9) , 3595-3617
Development of an Overset Near-Body Cartesian Solver for Graphite Ablation Simulations
The accurate modeling of hypersonic environments, including coupled ablation, is a challenging problem due to the complex flow physics, numerical accuracy, and robustness required for these simulations. The simulation mesh needs to be designed carefully, and structured high-aspect ratio stretched grids are typically used to properly capture the high wall-normal gradients. The mesh generation process proves to be a cumbersome and time-consuming process for realistic and complex vehicles, creating a severe bottleneck to the current CFD workflow. This work highlights the development of the Cartesian Higher-Order Adaptive Multi-Physics Solver (CHAMPS) near-body Cartesian grid solver, capable of automatic volume mesh generation, and its accurate and robust use in simulating coupled ablation for steady-state graphite ablation by interfacing with the Kentucky Aerothermodynamics and Thermal Response System Material Response (KATS-MR) solver. Validation on a Mach 8.7 cylinder and a Mach 22.88 axisymmetric Mars 2020 capsule showcases the challenges associated with shock-capturing on non-shock-aligned Cartesian grids. A verification study of the CHAMPS–KATS coupled ablation framework is performed for steady-state graphite ablation on a Mach 25.2, 9 deg blunt cone, followed by the validation of the solver for a blunt cone in the NASA Ames Interaction Heating Facility arcjet.
- 1 September 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 63 (9) , 3595-3617
Development of an Overset Near-Body Cartesian Solver for Graphite Ablation Simulations
The accurate modeling of hypersonic environments, including coupled ablation, is a challenging problem due to the complex flow physics, numerical accuracy, and robustness required for these simulations. The simulation mesh needs to be designed carefully, and structured high-aspect ratio stretched grids are typically used to properly capture the high wall-normal gradients. The mesh generation process proves to be a cumbersome and time-consuming process for realistic and complex vehicles, creating a severe bottleneck to the current CFD workflow. This work highlights the development of the Cartesian Higher-Order Adaptive Multi-Physics Solver (CHAMPS) near-body Cartesian grid solver, capable of automatic volume mesh generation, and its accurate and robust use in simulating coupled ablation for steady-state graphite ablation by interfacing with the Kentucky Aerothermodynamics and Thermal Response System Material Response (KATS-MR) solver. Validation on a Mach 8.7 cylinder and a Mach 22.88 axisymmetric Mars 2020 capsule showcases the challenges associated with shock-capturing on non-shock-aligned Cartesian grids. A verification study of the CHAMPS–KATS coupled ablation framework is performed for steady-state graphite ablation on a Mach 25.2, 9 deg blunt cone, followed by the validation of the solver for a blunt cone in the NASA Ames Interaction Heating Facility arcjet.
- 1 April 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- Vol. 39 (2) , 436-441
Multilayer Graphene and Graphite Oxidation Using Kinetic Monte Carlo
- 1 April 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- Vol. 39 (2) , 436-441
Multilayer Graphene and Graphite Oxidation Using Kinetic Monte Carlo
- 1 January 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 62 (1) , 7-17
Microscale Thermal–Structural Modeling for Carbon Fibers Subjected to a Hypersonic Boundary Layer
With regard to the thermal protection system, the thermal–structural responses of modern ablative materials are of primary importance in many aspects, including material selection and sizing. Due to the intricate nature of their porous structure and complicated thermal conditions they are subjected to, ablative materials may exhibit unexpected behavior, which can potentially lead to material failure. In this study, two solvers—a direct simulation Monte Carlo solver and a finite-volume-based material response solver—are coupled together to predict the microscale thermal–structural performance of a thermal protection system material like phenolic impregnated carbon ablator. In this approach, individual fibers are modeled at the microscale, which provides valuable knowledge of porous media behavior. Nonuniform boundary conditions, including the heat flux and external force, are captured by the direct simulation Monte Carlo solver, and the detailed thermal and structural performance of the fiber is captured by the material response solver. The results show that individual fibers do not fail based on the temperature gradient and applied aerodynamic forces. However, it is shown that the attachment points of the fibers are the most vulnerable. This vulnerability can potentially lead to a breakdown of the binders, which would separate fibers and cause material failure.
- 1 January 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 62 (1) , 7-17
Microscale Thermal–Structural Modeling for Carbon Fibers Subjected to a Hypersonic Boundary Layer
With regard to the thermal protection system, the thermal–structural responses of modern ablative materials are of primary importance in many aspects, including material selection and sizing. Due to the intricate nature of their porous structure and complicated thermal conditions they are subjected to, ablative materials may exhibit unexpected behavior, which can potentially lead to material failure. In this study, two solvers—a direct simulation Monte Carlo solver and a finite-volume-based material response solver—are coupled together to predict the microscale thermal–structural performance of a thermal protection system material like phenolic impregnated carbon ablator. In this approach, individual fibers are modeled at the microscale, which provides valuable knowledge of porous media behavior. Nonuniform boundary conditions, including the heat flux and external force, are captured by the direct simulation Monte Carlo solver, and the detailed thermal and structural performance of the fiber is captured by the material response solver. The results show that individual fibers do not fail based on the temperature gradient and applied aerodynamic forces. However, it is shown that the attachment points of the fibers are the most vulnerable. This vulnerability can potentially lead to a breakdown of the binders, which would separate fibers and cause material failure.
- 1 March 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 61 (2) , 438-447
Reconstruction of the Kentucky Re-Entry Universal Payload System Hypersonic Flight Trajectory
The Kentucky Re-entry Universal Payload System (KRUPS) is a small spacecraft developed to provide flight data during atmospheric reentry. The KRUPS capsules made a historic reentry into the Earth’s atmosphere in 2021, and this work details the reconstruction of the flight trajectories by inverse estimation based on the flight data. A trajectory modeling program is used with a one-dimensional material response solver to generate a prediction of the stagnation wall temperature of the KRUPS capsule during of the KRUPS capsule during reentry. These temperature results are compared to the temperature data obtained during the mission, and the initial parameters of the trajectory simulation are optimized to find the best estimated trajectories. The inverse estimation is performed in three ways: by assuming radiative equilibrium at the wall, by estimating the wall temperature after the trajectory simulations are first performed, and by coupling the trajectory and one-dimensional material response solver. Finally, the best estimated trajectories are compared against simulations performed using a three-dimensional material response solver, the Kentucky Aerodynamics and Thermal-response System Fluid Material Response module. It is observed that all approaches converge to a possible ejection of the KRUPS capsule into the Earth’s atmosphere at 35 km.
- 1 March 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 61 (2) , 438-447
Reconstruction of the Kentucky Re-Entry Universal Payload System Hypersonic Flight Trajectory
The Kentucky Re-entry Universal Payload System (KRUPS) is a small spacecraft developed to provide flight data during atmospheric reentry. The KRUPS capsules made a historic reentry into the Earth’s atmosphere in 2021, and this work details the reconstruction of the flight trajectories by inverse estimation based on the flight data. A trajectory modeling program is used with a one-dimensional material response solver to generate a prediction of the stagnation wall temperature of the KRUPS capsule during of the KRUPS capsule during reentry. These temperature results are compared to the temperature data obtained during the mission, and the initial parameters of the trajectory simulation are optimized to find the best estimated trajectories. The inverse estimation is performed in three ways: by assuming radiative equilibrium at the wall, by estimating the wall temperature after the trajectory simulations are first performed, and by coupling the trajectory and one-dimensional material response solver. Finally, the best estimated trajectories are compared against simulations performed using a three-dimensional material response solver, the Kentucky Aerodynamics and Thermal-response System Fluid Material Response module. It is observed that all approaches converge to a possible ejection of the KRUPS capsule into the Earth’s atmosphere at 35 km.
- 3 October 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 218
Validation and analysis of a coupled fluid-ablation framework for modeling low-temperature ablator
- 3 October 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 218
Validation and analysis of a coupled fluid-ablation framework for modeling low-temperature ablator
- 1 July 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- Vol. 37 (3) , 644-655
Numerical Investigation of Film Coefficient Approximation for Chemically Reacting Boundary-Layer Flows
Aerothermal analysis of spacecraft planetary entry is heavily dependent on heritage engineering models. The film coefficient heat transfer model examined in this paper estimates the convective heating to the vehicle for a laminar, dissociated, chemically reacting boundary layer for an Earth atmosphere. This model requires information about the vehicle and flowfield for a given trajectory point and estimates a proportional relationship between enthalpy potential and convective heat flux. In practice it is the aerothermal engineer who must decide which assumptions are appropriate for his/her application. This work looks at numerous CFD simulations for an arbitrary, axisymmetric flight vehicle to analyze the relative importance of both the mass and energy constraints imposed at the wall boundary, as well as the effect of various diffusion models. Within the subset of tested energy boundary conditions, it is found that the most desirable energy boundary condition is the radiative equilibrium boundary condition, which permits conservative estimates of convective heat flux, but also generates flowfield-dependent spatial thermal distributions along the surface. Other key findings are presented in an effort to make the film coefficient engineering model readily available to design engineers across industry.
- 1 July 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- Vol. 37 (3) , 644-655
Numerical Investigation of Film Coefficient Approximation for Chemically Reacting Boundary-Layer Flows
Aerothermal analysis of spacecraft planetary entry is heavily dependent on heritage engineering models. The film coefficient heat transfer model examined in this paper estimates the convective heating to the vehicle for a laminar, dissociated, chemically reacting boundary layer for an Earth atmosphere. This model requires information about the vehicle and flowfield for a given trajectory point and estimates a proportional relationship between enthalpy potential and convective heat flux. In practice it is the aerothermal engineer who must decide which assumptions are appropriate for his/her application. This work looks at numerous CFD simulations for an arbitrary, axisymmetric flight vehicle to analyze the relative importance of both the mass and energy constraints imposed at the wall boundary, as well as the effect of various diffusion models. Within the subset of tested energy boundary conditions, it is found that the most desirable energy boundary condition is the radiative equilibrium boundary condition, which permits conservative estimates of convective heat flux, but also generates flowfield-dependent spatial thermal distributions along the surface. Other key findings are presented in an effort to make the film coefficient engineering model readily available to design engineers across industry.
- 1 July 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 60 (4) , 1150-1159
Computational Fluid Dynamics Analysis of the Kentucky Re-Entry Universal Payload System
The Kentucky Re-Entry Universal Payload System (KRUPS) is a low-cost space capsule that has been designed to collect flight data. This work focuses on computational fluid dynamics (CFD) simulations of the flow around the capsule at various altitudes along the trajectory path during Earth re-entry. CFD simulations are performed at altitudes of 60 and 40 km by accounting for thermochemical nonequilibrium and surface catalycity using current state-of-the-art hypersonic approaches. The flowfield at all altitudes exhibits significant thermal and chemical nonequilibrium with vibrational temperature lagging the translational temperature in the forebody and exceeding the translational temperature in the wake. Inclusion of surface catalycity influences the heat flux on the surface and the flow temperature in the boundary layer. The number density profiles of nitric oxide molecules and spectral emission computations using the line-by-line radiative solver NEQAIR indicate that higher emissions would occur at an altitude of 60 km in comparison to emissions at 40 km, and spectral intensity would be higher along the stagnation line despite high densities of NO near the edges of the capsule, and that emissions in the 100–400 nm wavelength range are dominant.
- 1 July 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 60 (4) , 1150-1159
Computational Fluid Dynamics Analysis of the Kentucky Re-Entry Universal Payload System
The Kentucky Re-Entry Universal Payload System (KRUPS) is a low-cost space capsule that has been designed to collect flight data. This work focuses on computational fluid dynamics (CFD) simulations of the flow around the capsule at various altitudes along the trajectory path during Earth re-entry. CFD simulations are performed at altitudes of 60 and 40 km by accounting for thermochemical nonequilibrium and surface catalycity using current state-of-the-art hypersonic approaches. The flowfield at all altitudes exhibits significant thermal and chemical nonequilibrium with vibrational temperature lagging the translational temperature in the forebody and exceeding the translational temperature in the wake. Inclusion of surface catalycity influences the heat flux on the surface and the flow temperature in the boundary layer. The number density profiles of nitric oxide molecules and spectral emission computations using the line-by-line radiative solver NEQAIR indicate that higher emissions would occur at an altitude of 60 km in comparison to emissions at 40 km, and spectral intensity would be higher along the stagnation line despite high densities of NO near the edges of the capsule, and that emissions in the 100–400 nm wavelength range are dominant.
- Open Access
- 8 June 2023
- Published by Open Engineering Inc in engrXiv
Fully coupled material response and internal radiative heat transfer for 3D heat shield modeling
A material response code is strongly coupled with a radiative transfer equation (RTE) to evaluate the effect of a spectrally resolved heat flux on the thermal response of a heat shield. A P1 approximation model of RTE is used to account for radiation heat transfer within the material. First, the RTE model is verified by comparing the numerical results with the analytical solution. Next, the coupling scheme is verified by comparing the temperature histories computed by the pure conduction scheme with the ones computed by conduction coupled with radiative emission. The verification study is conducted using test cases from the literature (radiant heating, arc-jet heating, and space shuttle entry) as well as on a 3D Block, a 2D IsoQ sample, and the Stardust Return Capsule. The verification results are satisfactory for all cases. Thus, the verification results indicate that the coupling approach can accurately simulate the thermal response of the material. The coupling scheme was then used to simulate a laser heating experiment that studied the impact of spectral radiative heat transfer on ablative material. The results from the laser ablation simulations exhibit a behavior analogous to the experimental observations, indicating the importance of spectral radiative flux on the material response.
- 8 June 2023
- Published by Open Engineering Inc in engrXiv
Open AccessFully coupled material response and internal radiative heat transfer for 3D heat shield modeling
A material response code is strongly coupled with a radiative transfer equation (RTE) to evaluate the effect of a spectrally resolved heat flux on the thermal response of a heat shield. A P1 approximation model of RTE is used to account for radiation heat transfer within the material. First, the RTE model is verified by comparing the numerical results with the analytical solution. Next, the coupling scheme is verified by comparing the temperature histories computed by the pure conduction scheme with the ones computed by conduction coupled with radiative emission. The verification study is conducted using test cases from the literature (radiant heating, arc-jet heating, and space shuttle entry) as well as on a 3D Block, a 2D IsoQ sample, and the Stardust Return Capsule. The verification results are satisfactory for all cases. Thus, the verification results indicate that the coupling approach can accurately simulate the thermal response of the material. The coupling scheme was then used to simulate a laser heating experiment that studied the impact of spectral radiative heat transfer on ablative material. The results from the laser ablation simulations exhibit a behavior analogous to the experimental observations, indicating the importance of spectral radiative flux on the material response.