Sushma Santapuri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sushma Santapuri has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
Yadwinder Singh Joshan
Department of Applied Mechanics, Indian Institute of Technology Delhi, Hauz Khas, India
6 shared publicationsAwantika Mishra
4 shared publicationsStephen E. Bechtel
3 shared publications- Marcelo Jorge Dapino
Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH, USA
2 shared publications Sajan Kumar Wahi
2 shared publications- Sitikantha Roy
Department of Applied Mechanics, Indian Institute of Technology Delhi, New Delhi, India
2 shared publications
Latest Publications
- Open Access
- 19 June 2026
- Published by Springer Nature in Scientific Reports
Magnetorheological phase-change McKibben actuators for frequency-controlled actuation and high force output
State-of-the-art soft robots face a critical trade-off: high-performance pneumatic actuators require bulky external compressors, whereas emerging smart-material actuators often lack sufficient force output. Here, we present a magnetorheological elastomer (MRE)-based phase-change McKibben actuator actuated via induction heating. The inclusion of ferromagnetic particles contributes to improved force output and thermal response of the elastomeric matrix. Furthermore, the design enables wireless operation, where the induction coil’s excitation frequency directly regulates the electromagnetic heating and actuation timing. A multiphysics modeling framework, integrating finite element electromagnetic analysis with analytical fluid-pressurization and structural models, guides the actuator design. Prototypes operating at 127 kHz and 150 kHz are fabricated and tested. They produce up to 70 N blocked force at a 23 g mass, representing an increase over prior phase-change actuators. The force output is 48% higher, with faster heating and cooling times compared to identically dimensioned hyperelastic actuators. Increasing the induction frequency to 150 kHz reduces the time to reach a 35 N load by nearly 25%. With heating times of 10–20 s and wireless operation, this actuator represents a promising platform for lightweight soft robotic systems.
- 19 June 2026
- Published by Springer Nature in Scientific Reports
Open AccessMagnetorheological phase-change McKibben actuators for frequency-controlled actuation and high force output
State-of-the-art soft robots face a critical trade-off: high-performance pneumatic actuators require bulky external compressors, whereas emerging smart-material actuators often lack sufficient force output. Here, we present a magnetorheological elastomer (MRE)-based phase-change McKibben actuator actuated via induction heating. The inclusion of ferromagnetic particles contributes to improved force output and thermal response of the elastomeric matrix. Furthermore, the design enables wireless operation, where the induction coil’s excitation frequency directly regulates the electromagnetic heating and actuation timing. A multiphysics modeling framework, integrating finite element electromagnetic analysis with analytical fluid-pressurization and structural models, guides the actuator design. Prototypes operating at 127 kHz and 150 kHz are fabricated and tested. They produce up to 70 N blocked force at a 23 g mass, representing an increase over prior phase-change actuators. The force output is 48% higher, with faster heating and cooling times compared to identically dimensioned hyperelastic actuators. Increasing the induction frequency to 150 kHz reduces the time to reach a 35 N load by nearly 25%. With heating times of 10–20 s and wireless operation, this actuator represents a promising platform for lightweight soft robotic systems.
- 1 May 2025
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 113
Computational analysis of limit point instability in circular magnetoelastic membranes
- 1 May 2025
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 113
Computational analysis of limit point instability in circular magnetoelastic membranes
- 21 October 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (11) , 115038
Finite element analysis and design of a magnetostrictive material based vibration energy harvester with a magnetic flux path
This work presents the development of a nonlinear 2D finite element (FE) framework for magnetostrictive material based energy harvesters of beam geometry. The FE model is developed in COMSOL Multiphysics and compared with existing literature for validation. The FE model is subsequently used to study the effect of a closed magnetic flux path, consisting of ferromagnetic components, on the harvester output. Specifically, the voltage output is obtained by performing simulations on unimorph type harvester devices with and without a closed magnetic flux path, both operating at the same natural frequency and volume of the magnetostrictive material Galfenol. The harvester design considered here consists of a magnetostrictive layer (Galfenol) bonded to a steel substrate layer, a tip mass, a pick-up coil and a magnetic flux path consisting of soft iron core and NdFeB permanent magnets. Our results demonstrate a voltage gain of around 70% for the closed flux path design. Furthermore, a proof of concept prototype of the modified flux path design is developed, tested under impulse loading, and the voltage, power output are compared with FE simulation results for validation. The simulation results match well with experimental observations at two operating frequencies for the flux path design.
- 21 October 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (11) , 115038
Finite element analysis and design of a magnetostrictive material based vibration energy harvester with a magnetic flux path
This work presents the development of a nonlinear 2D finite element (FE) framework for magnetostrictive material based energy harvesters of beam geometry. The FE model is developed in COMSOL Multiphysics and compared with existing literature for validation. The FE model is subsequently used to study the effect of a closed magnetic flux path, consisting of ferromagnetic components, on the harvester output. Specifically, the voltage output is obtained by performing simulations on unimorph type harvester devices with and without a closed magnetic flux path, both operating at the same natural frequency and volume of the magnetostrictive material Galfenol. The harvester design considered here consists of a magnetostrictive layer (Galfenol) bonded to a steel substrate layer, a tip mass, a pick-up coil and a magnetic flux path consisting of soft iron core and NdFeB permanent magnets. Our results demonstrate a voltage gain of around 70% for the closed flux path design. Furthermore, a proof of concept prototype of the modified flux path design is developed, tested under impulse loading, and the voltage, power output are compared with FE simulation results for validation. The simulation results match well with experimental observations at two operating frequencies for the flux path design.
- 10 June 2024
- Published by SAGE Publications in Mathematics and Mechanics of Solids
- Vol. 29 (10) , 2112-2140
Finite deformation modeling of wrinkling in thin magnetoelastic sheets
This paper presents an asymptotic two-dimensional (2D) finite-deformation theory for a thin magnetoelastic sheet starting from a three-dimensional (3D) variational form. This theory is used to model wrinkling phenomena under applied traction and external magnetic field. The resulting 2D potential energy is specialized to an isotropic, in compressible material, and the expressions for material constants, i.e., elasticity tensor, magnetoelastic coupling constant, and permeability, are obtained as a function of the applied magnetic field. The formulation is further simplified assuming reflection symmetry about the mid-surface of the sheet. Strong form of the resulting 2D governing equations are obtained by setting the first variation of potential energy functional to zero. The resulting governing equations are used to analyze wrinkling in a stretched rectangular sheet placed in a uniform magnetic field. Approximate analytical solutions are obtained by linearizing the 2D plate equation for small slopes. The effect of magnetic field and applied stretch on onset of wrinkling and amplitude of wrinkles is studied.
- 10 June 2024
- Published by SAGE Publications in Mathematics and Mechanics of Solids
- Vol. 29 (10) , 2112-2140
Finite deformation modeling of wrinkling in thin magnetoelastic sheets
This paper presents an asymptotic two-dimensional (2D) finite-deformation theory for a thin magnetoelastic sheet starting from a three-dimensional (3D) variational form. This theory is used to model wrinkling phenomena under applied traction and external magnetic field. The resulting 2D potential energy is specialized to an isotropic, in compressible material, and the expressions for material constants, i.e., elasticity tensor, magnetoelastic coupling constant, and permeability, are obtained as a function of the applied magnetic field. The formulation is further simplified assuming reflection symmetry about the mid-surface of the sheet. Strong form of the resulting 2D governing equations are obtained by setting the first variation of potential energy functional to zero. The resulting governing equations are used to analyze wrinkling in a stretched rectangular sheet placed in a uniform magnetic field. Approximate analytical solutions are obtained by linearizing the 2D plate equation for small slopes. The effect of magnetic field and applied stretch on onset of wrinkling and amplitude of wrinkles is studied.
- Open Access
Modeling and parametric optimization of 3D tendon-sheath actuator system for upper limb soft exosuit
This paper presents an analysis of parametric characterization of a motor driven tendon-sheath actuator system for use in upper limb augmentation for applications such as rehabilitation, therapy, and industrial automation. The double tendon sheath system, which uses two sets of cables (agonist and antagonist side) guided through a sheath, is considered to produce smooth and natural-looking movements of the arm. The exoskeleton is equipped with a single motor capable of controlling both the flexion and extension motions. One of the key challenges in the implementation of a double tendon sheath system is the possibility of slack in the tendon, which can impact the overall performance of the system. To address this issue, a robust mathematical model is developed and a comprehensive parametric study is carried out to determine the most effective strategies for overcoming the problem of slack and improving the transmission. The study suggests that incorporating a series spring into the system's tendon leads to a universally applicable design, eliminating the need for individual customization. The results also show that the slack in the tendon can be effectively controlled by changing the pretension, spring constant, and size and geometry of spool mounted on the axle of motor.
Open AccessModeling and parametric optimization of 3D tendon-sheath actuator system for upper limb soft exosuit
This paper presents an analysis of parametric characterization of a motor driven tendon-sheath actuator system for use in upper limb augmentation for applications such as rehabilitation, therapy, and industrial automation. The double tendon sheath system, which uses two sets of cables (agonist and antagonist side) guided through a sheath, is considered to produce smooth and natural-looking movements of the arm. The exoskeleton is equipped with a single motor capable of controlling both the flexion and extension motions. One of the key challenges in the implementation of a double tendon sheath system is the possibility of slack in the tendon, which can impact the overall performance of the system. To address this issue, a robust mathematical model is developed and a comprehensive parametric study is carried out to determine the most effective strategies for overcoming the problem of slack and improving the transmission. The study suggests that incorporating a series spring into the system's tendon leads to a universally applicable design, eliminating the need for individual customization. The results also show that the slack in the tendon can be effectively controlled by changing the pretension, spring constant, and size and geometry of spool mounted on the axle of motor.
- 9 September 2023
- Published by Springer Nature in Continuum Mechanics and Thermodynamics
- Vol. 36 (5) , 1215-1245
Finite element modeling and analysis of flexoelectric plates using gradient electromechanical theory
- 9 September 2023
- Published by Springer Nature in Continuum Mechanics and Thermodynamics
- Vol. 36 (5) , 1215-1245
Finite element modeling and analysis of flexoelectric plates using gradient electromechanical theory
- 2 February 2023
- Published by Elsevier in International Journal of Non-Linear Mechanics
- Vol. 151
Structural instabilities in soft electro-magneto-elastic cylindrical membranes
- 2 February 2023
- Published by Elsevier in International Journal of Non-Linear Mechanics
- Vol. 151
Structural instabilities in soft electro-magneto-elastic cylindrical membranes
- Open Access
- 29 November 2022
- Published by Springer Nature in Research Square
Structural Instabilities in Soft Electro-Magneto-Elastic Cylindrical Membranes
In the present work, a nonlinear coupled electro-magneto-elastic membrane formulation is developed for soft functional materials starting from the variational form of 3D governing equations. The resulting 2D model is applied to an internally pressurized cylindrical membrane placed in an azimuthal magnetic field and radial electric field. The results of our model are verified with existing literature for some special cases. The model is subsequently used to analyze mechanical and electrical limit-point instabilities, and the effect of external fields on the onset of these instabilities. It is observed that the onset of mechanical limit-point instability, defined by a loss of monotonicity in the pressure versus deformation plots, is dependent on the material properties, geometrical parameters and applied electromagnetic fields. Magnetic field induced instability results in an initial dip in the pressure versus stretch plots, subsequently converging to the purely hyperelastic membrane behavior at larger stretches. Application of electric field, on the other hand, results in an early onset of limit-point instability (i.e., at smaller stretches) compared to the hyperelastic case. Additionally, electrical limit-point instability, characterized by a loss of monotonicity in voltage versus stretch plots, is observed and its dependence on magnetic field and force inputs is studied. Finally, we study the effect of Maxwell stress due to electromagnetic fields. It is observed that ignoring the Maxwell stress related traction boundary term results in an error of up to 10\%, depending on the force and magnetic fields inputs. In summary, our membrane model describes the interactions between the electromagnetic fields and deformation in a soft functional material, and can be applied towards design of soft actuator and sensor devices.
- 29 November 2022
- Published by Springer Nature in Research Square
Open AccessStructural Instabilities in Soft Electro-Magneto-Elastic Cylindrical Membranes
In the present work, a nonlinear coupled electro-magneto-elastic membrane formulation is developed for soft functional materials starting from the variational form of 3D governing equations. The resulting 2D model is applied to an internally pressurized cylindrical membrane placed in an azimuthal magnetic field and radial electric field. The results of our model are verified with existing literature for some special cases. The model is subsequently used to analyze mechanical and electrical limit-point instabilities, and the effect of external fields on the onset of these instabilities. It is observed that the onset of mechanical limit-point instability, defined by a loss of monotonicity in the pressure versus deformation plots, is dependent on the material properties, geometrical parameters and applied electromagnetic fields. Magnetic field induced instability results in an initial dip in the pressure versus stretch plots, subsequently converging to the purely hyperelastic membrane behavior at larger stretches. Application of electric field, on the other hand, results in an early onset of limit-point instability (i.e., at smaller stretches) compared to the hyperelastic case. Additionally, electrical limit-point instability, characterized by a loss of monotonicity in voltage versus stretch plots, is observed and its dependence on magnetic field and force inputs is studied. Finally, we study the effect of Maxwell stress due to electromagnetic fields. It is observed that ignoring the Maxwell stress related traction boundary term results in an error of up to 10\%, depending on the force and magnetic fields inputs. In summary, our membrane model describes the interactions between the electromagnetic fields and deformation in a soft functional material, and can be applied towards design of soft actuator and sensor devices.
- 23 July 2022
- Published by Springer Nature in Zeitschrift für angewandte Mathematik und Physik
- Vol. 73 (5) , 1-33
A gradient electromechanical theory for thin dielectric curved beams considering direct and converse flexoelectric effects
- 23 July 2022
- Published by Springer Nature in Zeitschrift für angewandte Mathematik und Physik
- Vol. 73 (5) , 1-33
A gradient electromechanical theory for thin dielectric curved beams considering direct and converse flexoelectric effects
- Open Access
- 11 March 2022
- Published by Springer Nature in Research Square
Gradient Electromechanical Theory for Thin Dielectric Curved Beams Considering Direct and Converse Flexoelectric Effects
This work presents the development of a unified gradient electromechanical theory for thin flexoelectric beams considering both direct and converse flexoelectric effects. The two-way coupled electromechanical theory is developed starting from 3D variational formulation by considering an electric field-strain based free energy function. The formulation incorporates mechanical as well as electrical size effects. The coupled 3D theory is specialized to isotropic materials and a 1D beam theory for composite flexoelectric curved beams is derived using the classical Kirchhoff assumptions. The beam theory is solved using a novel C2 continuous finite element framework for different loading and boundary conditions. Our finite element results are verified with analytical solutions for a simply-supported flexoelectric beam operating in both actuator and sensor modes. The results are also compared with existing literature for the special case of a passive micro-beam. Our computational framework is subsequently used to perform various parametric studies to analyze the effect of electrical and mechanical length scale parameters, geometric parameters like the radius of curvature, flexoelectric layer thickness etc., on the response of the beam. Also, contribution of converse flexoelectricity in the overall response of the flexoelectric beam is compared with that of the direct effect. Our simulation results predict that the converse effect is significant (≈ 10-25% of the direct effect) for a wide range of thickness and length scale parameter values. It is also observed that the effective electromechanical coupling coefficient, calculated in terms of the voltage developed across the flexoelectric layer thickness, is higher in flexoelectric materials compared to piezoelectric materials at smaller length scales (thickness of the order of a few microns). The trends observed in our simulation results also agree with recent experimental findings.
- 11 March 2022
- Published by Springer Nature in Research Square
Open AccessGradient Electromechanical Theory for Thin Dielectric Curved Beams Considering Direct and Converse Flexoelectric Effects
This work presents the development of a unified gradient electromechanical theory for thin flexoelectric beams considering both direct and converse flexoelectric effects. The two-way coupled electromechanical theory is developed starting from 3D variational formulation by considering an electric field-strain based free energy function. The formulation incorporates mechanical as well as electrical size effects. The coupled 3D theory is specialized to isotropic materials and a 1D beam theory for composite flexoelectric curved beams is derived using the classical Kirchhoff assumptions. The beam theory is solved using a novel C2 continuous finite element framework for different loading and boundary conditions. Our finite element results are verified with analytical solutions for a simply-supported flexoelectric beam operating in both actuator and sensor modes. The results are also compared with existing literature for the special case of a passive micro-beam. Our computational framework is subsequently used to perform various parametric studies to analyze the effect of electrical and mechanical length scale parameters, geometric parameters like the radius of curvature, flexoelectric layer thickness etc., on the response of the beam. Also, contribution of converse flexoelectricity in the overall response of the flexoelectric beam is compared with that of the direct effect. Our simulation results predict that the converse effect is significant (≈ 10-25% of the direct effect) for a wide range of thickness and length scale parameter values. It is also observed that the effective electromechanical coupling coefficient, calculated in terms of the voltage developed across the flexoelectric layer thickness, is higher in flexoelectric materials compared to piezoelectric materials at smaller length scales (thickness of the order of a few microns). The trends observed in our simulation results also agree with recent experimental findings.