Fan Wang
Fan Wang has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Rahim Tafazolli
University of Surrey
7 shared publications - Mohsen Khalily
Institute for Communication Systems (ICS), University of Surrey, Guildford, U.K.
6 shared publications - Ali Araghi
Institute for Communication Systems (ICS), Home for 5G and 6G Innovation Centers, University of Surrey, Guildford, U.K.
3 shared publications - Ahmed Elzanaty
University of Surrey
2 shared publications - Amirmasood Bagheri
Institute for Communication Systems (ICS), Home for 5G and 6G Innovation Centers, University of Surrey, Guildford, U.K.
2 shared publications - Gabriele Gradoni
G Innovation Center, Institute for Communication Systems, University of Surrey, Guildford, U.K.
2 shared publications
Latest Publications
- 1 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Wireless Communications Letters
- Vol. 15 (21622337) , 3392-3396
PAPR Reduction and Ambiguity Preserving for DFT-s-OFDM Systems
Achieving a low peak-to-average power ratio (PAPR) is essential for discrete Fourier transform-spread orthogonal frequency division multiplexing (DFT-s-OFDM) systems. However, when applied to binary sequences such as m-sequences and Gold sequences, conventional PAPR reduction techniques typically degrade ambiguity properties, leading to poor synchronization and sensing performance. To this end, this letter proposes a constellation rotation method for DFT-s-OFDM systems that can achieve low PAPR and preserve favorable ambiguity properties. First, we formulate a PAPR minimization problem subject to ambiguity-preserving constraints. Then, a two-step solution is developed to solve the proposed optimization problem. Step 1 derives the feasible sets of constellation rotations that preserve ambiguity properties. Step 2 determines the optimal constellation rotation in the feasible sets by the objective function under the condition of deterministic and stochastic inputs, respectively. Specifically, for deterministic inputs, we illustrate the approach with a low-PAPR pseudo-random sequence design. For stochastic inputs, the closed-form solution is provided. Finally, simulation results demonstrate that the proposed method achieves good PAPR performance while maintaining the ambiguity properties of the original sequences.
- 1 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Wireless Communications Letters
- Vol. 15 (21622337) , 3392-3396
PAPR Reduction and Ambiguity Preserving for DFT-s-OFDM Systems
Achieving a low peak-to-average power ratio (PAPR) is essential for discrete Fourier transform-spread orthogonal frequency division multiplexing (DFT-s-OFDM) systems. However, when applied to binary sequences such as m-sequences and Gold sequences, conventional PAPR reduction techniques typically degrade ambiguity properties, leading to poor synchronization and sensing performance. To this end, this letter proposes a constellation rotation method for DFT-s-OFDM systems that can achieve low PAPR and preserve favorable ambiguity properties. First, we formulate a PAPR minimization problem subject to ambiguity-preserving constraints. Then, a two-step solution is developed to solve the proposed optimization problem. Step 1 derives the feasible sets of constellation rotations that preserve ambiguity properties. Step 2 determines the optimal constellation rotation in the feasible sets by the objective function under the condition of deterministic and stochastic inputs, respectively. Specifically, for deterministic inputs, we illustrate the approach with a low-PAPR pseudo-random sequence design. For stochastic inputs, the closed-form solution is provided. Finally, simulation results demonstrate that the proposed method achieves good PAPR performance while maintaining the ambiguity properties of the original sequences.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Wireless Communications
- Vol. 25, 25760-25776
Electromagnetic Channel Model and Sensing Performance for ISAC: The Case of a Single Cylindrical Scatterer
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Wireless Communications
- Vol. 25, 25760-25776
Electromagnetic Channel Model and Sensing Performance for ISAC: The Case of a Single Cylindrical Scatterer
- 28 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 12 (15) , 30533-30547
Near-Field Localization With Physics-Compliant Electromagnetic Model: Algorithms and Model Mismatch Analysis
Accurate signal localization is critical for Internet of Things (IoT) applications, but precise propagation models are often unavailable due to uncontrollable factors. Simplified models, such as planar and spherical wavefront approximations, are widely used but can cause model mismatches that reduce accuracy. To address this, we propose an expected likelihood (EL) framework for model mismatch analysis and online (on-the-fly) model selection. The EL idea is that under the Gaussian assumption of independent samples, the likelihood ratio of the actual covariance matrix of the received signal is described by a distribution that depends only on the number of samples and receive antennas, not the true covariance itself. This scenario independence allows us to avoid the true model need-to-know requirement for model mismatch analysis. In this article, we formulate an EL approach for online model and estimation parameters selection, and demonstrate its applicability and efficiency using the analytical electromagnetic model for data generation and considering different simplified models for source localization in both direct and reconfigurable intelligent surface assisted diverse IoT environments.
- 28 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 12 (15) , 30533-30547
Near-Field Localization With Physics-Compliant Electromagnetic Model: Algorithms and Model Mismatch Analysis
Accurate signal localization is critical for Internet of Things (IoT) applications, but precise propagation models are often unavailable due to uncontrollable factors. Simplified models, such as planar and spherical wavefront approximations, are widely used but can cause model mismatches that reduce accuracy. To address this, we propose an expected likelihood (EL) framework for model mismatch analysis and online (on-the-fly) model selection. The EL idea is that under the Gaussian assumption of independent samples, the likelihood ratio of the actual covariance matrix of the received signal is described by a distribution that depends only on the number of samples and receive antennas, not the true covariance itself. This scenario independence allows us to avoid the true model need-to-know requirement for model mismatch analysis. In this article, we formulate an EL approach for online model and estimation parameters selection, and demonstrate its applicability and efficiency using the analytical electromagnetic model for data generation and considering different simplified models for source localization in both direct and reconfigurable intelligent surface assisted diverse IoT environments.
- Open Access
- 17 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 5 (6) , 1786-1794
Active Gain-Controlled Beam-Steering Transmissive Surface
Engineered electromagnetic surfaces enable enhancing the strength of a signal in the desired direction(s) using anomalous reflection/transmission. However, to boost the gain of the conventional surfaces, the common solution is to increase its aperture size where this method limits the gain performance for limited space in scenarios for large-distance communication. This paper proposes a gain-controlled beam-steering polarization-engineered transmissive surface to tackle this challenge. To implement such a functionality, a transmissive unit cell properly integrated with transistors and phase shifters is introduced with the ability of simultaneous manipulation of phase, amplitude (reduction and amplification), and polarization. Then, a supercell including the array of unit cells with desired linear phase gradient is designed and analyzed using Floquet approach to tilt the transmitted beam. Finally, to verify the proposed idea, a surface including 12×12 unit cells is designed, fabricated and verified. It is demonstrated that a maximum gain of 25 dB compared to air aperture and 11 dB compared to the passive one are achieved by assuming a constant size at 5 GHz. Based on this gain improvement, the active surface’s aperture efficiency is 12.58 times greater than that of the passive surface. Moreover, the surface gain can be reconfigured by the amplification level of the transistors, providing efficient dynamic way for changing the gain instead of the static resizing of aperture.
- 17 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 5 (6) , 1786-1794
Open AccessActive Gain-Controlled Beam-Steering Transmissive Surface
Engineered electromagnetic surfaces enable enhancing the strength of a signal in the desired direction(s) using anomalous reflection/transmission. However, to boost the gain of the conventional surfaces, the common solution is to increase its aperture size where this method limits the gain performance for limited space in scenarios for large-distance communication. This paper proposes a gain-controlled beam-steering polarization-engineered transmissive surface to tackle this challenge. To implement such a functionality, a transmissive unit cell properly integrated with transistors and phase shifters is introduced with the ability of simultaneous manipulation of phase, amplitude (reduction and amplification), and polarization. Then, a supercell including the array of unit cells with desired linear phase gradient is designed and analyzed using Floquet approach to tilt the transmitted beam. Finally, to verify the proposed idea, a surface including 12×12 unit cells is designed, fabricated and verified. It is demonstrated that a maximum gain of 25 dB compared to air aperture and 11 dB compared to the passive one are achieved by assuming a constant size at 5 GHz. Based on this gain improvement, the active surface’s aperture efficiency is 12.58 times greater than that of the passive surface. Moreover, the surface gain can be reconfigured by the amplification level of the transistors, providing efficient dynamic way for changing the gain instead of the static resizing of aperture.
- Open Access
- 12 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 38218-38225
MM-Wave High Isolated Dual Polarized Dielectric Resonator Antenna for In-Band Full-Duplex Systems
A novel high-isolation dual-polarized in-band full-duplex (IBFD) dielectric resonator antenna (DRA) for satellite communications using a decoupling structure is proposed. Good isolation between transmit and receive ports is achieved by placing two identical linearly polarized resonators orthogonal to each other. Each resonator consists of a main rectangular dielectric resonator of the dielectric constant of 10 and is loaded by a thin dielectric slab of lower permittivity of 5 to broaden the matching bandwidth further. The isolation is further improved by loading an absorber and etching several slots in the ground plane. Finally, the proposed DRA is fabricated and measured to validate the concepts. Measurement results show high isolation of more than 50 dB over the desired operating bandwidth from 23.04 GHz to 24.08 GHz (ka-band) with a peak gain of about 8.93 dBi and 8.09 dBi for Port 1 and Port 2, respectively. In addition, the proposed IBFD DRA provides 11.87 GHz and 4.84 GHz isolation bandwidths over 25 dB and 30 dB, respectively, making it a potential candidate for mm-wave terrestrial applications.
- 12 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 38218-38225
Open AccessMM-Wave High Isolated Dual Polarized Dielectric Resonator Antenna for In-Band Full-Duplex Systems
A novel high-isolation dual-polarized in-band full-duplex (IBFD) dielectric resonator antenna (DRA) for satellite communications using a decoupling structure is proposed. Good isolation between transmit and receive ports is achieved by placing two identical linearly polarized resonators orthogonal to each other. Each resonator consists of a main rectangular dielectric resonator of the dielectric constant of 10 and is loaded by a thin dielectric slab of lower permittivity of 5 to broaden the matching bandwidth further. The isolation is further improved by loading an absorber and etching several slots in the ground plane. Finally, the proposed DRA is fabricated and measured to validate the concepts. Measurement results show high isolation of more than 50 dB over the desired operating bandwidth from 23.04 GHz to 24.08 GHz (ka-band) with a peak gain of about 8.93 dBi and 8.09 dBi for Port 1 and Port 2, respectively. In addition, the proposed IBFD DRA provides 11.87 GHz and 4.84 GHz isolation bandwidths over 25 dB and 30 dB, respectively, making it a potential candidate for mm-wave terrestrial applications.
- Open Access
- 23 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 19613-19621
Mathematical Model and Real-World Demonstration of Multi-Beam and Wide-Beam Reconfigurable Intelligent Surface
In this paper, a mathematical model is proposed to govern the phase distribution on a reconfigurable intelligent surface (RIS) for anomalously reflecting the beam towards the directions of interest. To this end, two operational modes are defined with respect to the reflected pattern. In the first mode, the RIS is configured to form multi-reflected beams toward the directions of interest capable of being controlled independently. The second mode is when the RIS provides a wide reflected beam. Regarding to each mode, a cost function is derived and then, in order to enhance the reflected pattern characteristics, a genetic algorithm (GA) is employed to the model as optimization method. To validate the practicality of the method, the proposed model is applied to a fabricated RIS to assess its performance in a real-world outdoor scenario. In the first mode, an asymmetric dual-beam reflected pattern is obtained and tested with tilt angles of θ 0 = 60° and θ 1 = 135°. Furthermore, a wide-reflected beam is generated in the second mode with half-power beamwidth of θ HPBW = 30° and tilt angle of θ 0 = 75°. At both modes, the measured data are well aligned with the simulated results.
- 23 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 19613-19621
Open AccessMathematical Model and Real-World Demonstration of Multi-Beam and Wide-Beam Reconfigurable Intelligent Surface
In this paper, a mathematical model is proposed to govern the phase distribution on a reconfigurable intelligent surface (RIS) for anomalously reflecting the beam towards the directions of interest. To this end, two operational modes are defined with respect to the reflected pattern. In the first mode, the RIS is configured to form multi-reflected beams toward the directions of interest capable of being controlled independently. The second mode is when the RIS provides a wide reflected beam. Regarding to each mode, a cost function is derived and then, in order to enhance the reflected pattern characteristics, a genetic algorithm (GA) is employed to the model as optimization method. To validate the practicality of the method, the proposed model is applied to a fabricated RIS to assess its performance in a real-world outdoor scenario. In the first mode, an asymmetric dual-beam reflected pattern is obtained and tested with tilt angles of θ 0 = 60° and θ 1 = 135°. Furthermore, a wide-reflected beam is generated in the second mode with half-power beamwidth of θ HPBW = 30° and tilt angle of θ 0 = 75°. At both modes, the measured data are well aligned with the simulated results.
- 28 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 21 (10) , 1960-1964
Systematic Design of a Holographic-Based Metasurface Reflector in the Sub-6 GHz Band
This letter presents a systematic method to regulating the response of an artificial impedance surface. The method is based on governing the dispersion diagram to control the depth of modulation so that a meaningful pattern of scatterers is obtained on the structure. The method is applied on a holographic-based large reflective metasurface to achieve a dual-beam radiation pattern with tilt angles of$\pm 45^{\circ }$ in the azimuth plane at$f=3.5$ GHz. The structure is fabricated and the measured data concur with the simulation results.- 28 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 21 (10) , 1960-1964
Systematic Design of a Holographic-Based Metasurface Reflector in the Sub-6 GHz Band
This letter presents a systematic method to regulating the response of an artificial impedance surface. The method is based on governing the dispersion diagram to control the depth of modulation so that a meaningful pattern of scatterers is obtained on the structure. The method is applied on a holographic-based large reflective metasurface to achieve a dual-beam radiation pattern with tilt angles of$\pm 45^{\circ }$ in the azimuth plane at$f=3.5$ GHz. The structure is fabricated and the measured data concur with the simulation results.- Top Cited PapersOpen Access
- 4 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 2646-2655
Reconfigurable Intelligent Surface (RIS) in the Sub-6 GHz Band: Design, Implementation, and Real-World Demonstration
Here, we first aim to explain practical considerations to design and implement a reconfigurable intelligent surface (RIS) in the sub-6 GHz band and then, to demonstrate its real-world performance. The wave manipulation procedure is explored with a discussion on relevant electromagnetic (EM) concepts and backgrounds. Based on that, the RIS is designed and fabricated to operate at the center frequency of 3.5 GHz. The surface is composed of 2430 unit cells where the engineered reflecting response is obtained by governing the microscopic characteristics of the conductive patches printed on each unit cell. To achieve this goal, the patches are not only geometrically customized to properly reflect the local waves, but also are equipped with specific varactor diodes to be able to reconfigure their response when it is required. An equivalent circuit model is presented to analytically evaluate the unit cell’s performance with a method to measure the unit cell’s characteristics from the macroscopic response of the RIS. The patches are printed on six standard-size substrates which then placed together to make a relatively big aperture with approximate planar dimensions of 120 W 120 cm2. The manufactured RIS possesses a control unit with a custom-built system that can control the response of the reflecting surface by regulating the performance of the varactor diode on each printed patch across the structure. Furthermore, with an introduction of our test-bed system, the functionality of the developed RIS in an indoor real-world scenario is assessed. Finally, we showcase the capability of the RIS in hand to reconfigure itself in order to anomalously reflect the incoming EM waves toward the direction of interest in which a receiver could be experiencing poor coverage.
- 4 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 2646-2655
Top Cited PapersOpen AccessReconfigurable Intelligent Surface (RIS) in the Sub-6 GHz Band: Design, Implementation, and Real-World Demonstration
Here, we first aim to explain practical considerations to design and implement a reconfigurable intelligent surface (RIS) in the sub-6 GHz band and then, to demonstrate its real-world performance. The wave manipulation procedure is explored with a discussion on relevant electromagnetic (EM) concepts and backgrounds. Based on that, the RIS is designed and fabricated to operate at the center frequency of 3.5 GHz. The surface is composed of 2430 unit cells where the engineered reflecting response is obtained by governing the microscopic characteristics of the conductive patches printed on each unit cell. To achieve this goal, the patches are not only geometrically customized to properly reflect the local waves, but also are equipped with specific varactor diodes to be able to reconfigure their response when it is required. An equivalent circuit model is presented to analytically evaluate the unit cell’s performance with a method to measure the unit cell’s characteristics from the macroscopic response of the RIS. The patches are printed on six standard-size substrates which then placed together to make a relatively big aperture with approximate planar dimensions of 120 W 120 cm2. The manufactured RIS possesses a control unit with a custom-built system that can control the response of the reflecting surface by regulating the performance of the varactor diode on each printed patch across the structure. Furthermore, with an introduction of our test-bed system, the functionality of the developed RIS in an indoor real-world scenario is assessed. Finally, we showcase the capability of the RIS in hand to reconfigure itself in order to anomalously reflect the incoming EM waves toward the direction of interest in which a receiver could be experiencing poor coverage.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 433-438
Multi-Phase Interleaved Bidirectional DC/DC Converter with Two-Winding Coupled Inductors
The interleaved and magnetically integrated bidirectional DC/DC converters are widely used in more and more applications. Currently in these converters, most of the phase inductors are normally integrated to one single-core coupled inductor. With the number of phases increasing, however, this may suffer several problems, such as asymmetry of magnetic components, difficulties of designing suitable multi-phase magnetic core, large DC flux and so on. To solve these issues, a multi-phase interleaved bidirectional DC/DC converter (IBDC) with two-winding coupled inductors (TCIs) is proposed and analyzed. A four-phase IBDC is taken as an example in this paper, where four TCIs are used to replace the single-core coupled inductor. The steady-state and transient-state performances of the proposed converter are studied in detail. The parameter design criteria of TCIs is also given. Finally, the superiority and practicability of the proposed converter are verified by the prototype experiments.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 433-438
Multi-Phase Interleaved Bidirectional DC/DC Converter with Two-Winding Coupled Inductors
The interleaved and magnetically integrated bidirectional DC/DC converters are widely used in more and more applications. Currently in these converters, most of the phase inductors are normally integrated to one single-core coupled inductor. With the number of phases increasing, however, this may suffer several problems, such as asymmetry of magnetic components, difficulties of designing suitable multi-phase magnetic core, large DC flux and so on. To solve these issues, a multi-phase interleaved bidirectional DC/DC converter (IBDC) with two-winding coupled inductors (TCIs) is proposed and analyzed. A four-phase IBDC is taken as an example in this paper, where four TCIs are used to replace the single-core coupled inductor. The steady-state and transient-state performances of the proposed converter are studied in detail. The parameter design criteria of TCIs is also given. Finally, the superiority and practicability of the proposed converter are verified by the prototype experiments.