Ian Ridley
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ian Ridley has a total of 134 co-authors. Here are the top co-authors by number of shared publications:
- Tadj Oreszczyn
UCL Energy Institute, University College London, London
17 shared publications - Ian Hamilton
Energy Institute, University College London, London, UK
8 shared publications M. Davies
8 shared publicationsMichael Davies
7 shared publicationsRussell Binions
7 shared publications- Dejan Mumovic
Institute for Environmental Design and Engineering, The Bartlett Faculty of the Built Environment, University College London, London WC1H 0NN, UK
6 shared publications
Latest Publications
- 1 May 2020
- Published by Elsevier in Journal of Building Engineering
- Vol. 29, 101137
Assessing the energy and indoor-PM2.5-exposure impacts of control strategies for residential energy recovery ventilators
- 1 May 2020
- Published by Elsevier in Journal of Building Engineering
- Vol. 29, 101137
Assessing the energy and indoor-PM2.5-exposure impacts of control strategies for residential energy recovery ventilators
- 24 August 2017
- Published by Taylor & Francis in Housing Studies
- Vol. 35 (1) , 1-28
Understanding the contextual influences of the health outcomes of residential energy efficiency interventions: realist review
- 24 August 2017
- Published by Taylor & Francis in Housing Studies
- Vol. 35 (1) , 1-28
Understanding the contextual influences of the health outcomes of residential energy efficiency interventions: realist review
- Open Access
Variation of Thermochromic Glazing Systems Transition Temperature, Hysteresis Gradient and Width Effect on Energy Efficiency
Due to increasing pressure to reduce the energy demand in buildings, thermochromic thin film based glazing has become a recognized potential solution due to the intrinsic ability to modulate the solar heat gain of a window as a function of the materials temperature. These “intelligent” glazings have been investigated for several years, and it has been found that, through variation of synthetic route, the thermochromic properties (transition temperature, hysteresis gradient and width) can be altered; however, less attention has been applied to how such alterations affect the overall energy savings attributed to the materials. In this study the building simulation software EnergyPlus TM has been used to model a series of idealized thermochromic spectra in a series of different environments to evaluate their energy saving potential against both clear glass systems and industry standards. The idealized spectra are used to see what effect each of the materials thermochromic properties and therefore elucidate which are the most important with respect to the energy saving properties. It was found that the best thermochromic materials were those with a narrow sharp hysteresis and a low transition temperature and result in an increase in energy saving between 30%–45% across the different environments compared to clear glass systems.
Open AccessVariation of Thermochromic Glazing Systems Transition Temperature, Hysteresis Gradient and Width Effect on Energy Efficiency
Due to increasing pressure to reduce the energy demand in buildings, thermochromic thin film based glazing has become a recognized potential solution due to the intrinsic ability to modulate the solar heat gain of a window as a function of the materials temperature. These “intelligent” glazings have been investigated for several years, and it has been found that, through variation of synthetic route, the thermochromic properties (transition temperature, hysteresis gradient and width) can be altered; however, less attention has been applied to how such alterations affect the overall energy savings attributed to the materials. In this study the building simulation software EnergyPlus TM has been used to model a series of idealized thermochromic spectra in a series of different environments to evaluate their energy saving potential against both clear glass systems and industry standards. The idealized spectra are used to see what effect each of the materials thermochromic properties and therefore elucidate which are the most important with respect to the energy saving properties. It was found that the best thermochromic materials were those with a narrow sharp hysteresis and a low transition temperature and result in an increase in energy saving between 30%–45% across the different environments compared to clear glass systems.
- 9 March 2016
- Published by Taylor & Francis in Building Research & Information
- Vol. 45 (4) , 443-456
Dwelling performance and adaptive summer comfort in low-income Australian households
Increasing reliance on air-conditioning to improve summertime comfort in dwellings results in higher energy bills, peak electricity demand and environmental issues. In pursuit of social equity, society needs to develop ways of improving cooling that are less reliant on air-conditioning. Designing homes to emphasize adaptive thermal comfort can reduce this reliance, particularly when combined with improved dwelling thermal performance. A multi-method evaluation of 10 low-income dwellings in the state of Victoria in Australia is presented, including low-energy and ‘standard-performance’ houses. The combination of performance monitoring and householder interviews reveals new insights for achieving summertime comfort. The low-energy houses without air-conditioning were both measured and perceived as more comfortable than the ‘standard-performance’ houses with air-conditioning. The low-energy households achieved improved personal thermal comfort through a combination of improved fabric performance augmented with adaptive comfort activities (e.g., opening/closing windows). This outcome reduces reliance on air-conditioning, reduces living costs and energy consumption, and improves environmental outcomes. There is a need to integrate lessons from adaptive thermal comfort theory and strategies into minimum building performance requirements and standards, as well as wider design strategies. It is evident that adaptive comfort has a role to play in a transition to a low-carbon housing future.
- 9 March 2016
- Published by Taylor & Francis in Building Research & Information
- Vol. 45 (4) , 443-456
Dwelling performance and adaptive summer comfort in low-income Australian households
Increasing reliance on air-conditioning to improve summertime comfort in dwellings results in higher energy bills, peak electricity demand and environmental issues. In pursuit of social equity, society needs to develop ways of improving cooling that are less reliant on air-conditioning. Designing homes to emphasize adaptive thermal comfort can reduce this reliance, particularly when combined with improved dwelling thermal performance. A multi-method evaluation of 10 low-income dwellings in the state of Victoria in Australia is presented, including low-energy and ‘standard-performance’ houses. The combination of performance monitoring and householder interviews reveals new insights for achieving summertime comfort. The low-energy houses without air-conditioning were both measured and perceived as more comfortable than the ‘standard-performance’ houses with air-conditioning. The low-energy households achieved improved personal thermal comfort through a combination of improved fabric performance augmented with adaptive comfort activities (e.g., opening/closing windows). This outcome reduces reliance on air-conditioning, reduces living costs and energy consumption, and improves environmental outcomes. There is a need to integrate lessons from adaptive thermal comfort theory and strategies into minimum building performance requirements and standards, as well as wider design strategies. It is evident that adaptive comfort has a role to play in a transition to a low-carbon housing future.
- 1 May 2015
- Published by Elsevier in Social Science & Medicine
- Vol. 133, 191-201
Towards explaining the health impacts of residential energy efficiency interventions – A realist review. Part 1: Pathways
- 1 May 2015
- Published by Elsevier in Social Science & Medicine
- Vol. 133, 191-201
Towards explaining the health impacts of residential energy efficiency interventions – A realist review. Part 1: Pathways
- 1 October 2014
- Published by Elsevier in Energy and Buildings
- Vol. 82, 13-26
The side by side in use monitored performance of two passive and low carbon Welsh houses
- 1 October 2014
- Published by Elsevier in Energy and Buildings
- Vol. 82, 13-26
The side by side in use monitored performance of two passive and low carbon Welsh houses
- 1 July 2014
- Published by Elsevier in Energy and Buildings
- Vol. 77, 80-90
The effect of transition gradient in thermochromic glazing systems
- 1 July 2014
- Published by Elsevier in Energy and Buildings
- Vol. 77, 80-90
The effect of transition gradient in thermochromic glazing systems
- 1 November 2013
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 118, 149-156
Synthesis and energy modelling studies of titanium oxy-nitride films as energy efficient glazing
- 1 November 2013
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 118, 149-156
Synthesis and energy modelling studies of titanium oxy-nitride films as energy efficient glazing
- 1 September 2013
- Published by Elsevier in Surface and Coatings Technology
- Vol. 230, 163-167
Thermochromic vanadium dioxide thin films from electric field assisted aerosol assisted chemical vapour deposition
- 1 September 2013
- Published by Elsevier in Surface and Coatings Technology
- Vol. 230, 163-167
Thermochromic vanadium dioxide thin films from electric field assisted aerosol assisted chemical vapour deposition
- Open Access
- 12 August 2013
- Published by SAGE Publications in Building Services Engineering Research & Technology
- Vol. 35 (4) , 408-416
Modelling uniformly porous facades to predict dwelling infiltration rates
It is important to limit dwelling infiltration to reduce energy demand and help meet national climate change commitments while concurrently providing sufficient ventilation to deliver adequate indoor air quality. DOMVENT3D is a model of infiltration and exfiltration that assumes a linear pressure distribution over any number of uniformly porous facades and integrates the airflow rate in the vertical plane to predict the theoretically correct airflow rate through them. DOMVENT3D is a new development of an existing two-dimensional model of infiltration that provides more opportunities for investigating a greater number of dwellings than was previously possible. Initial testing suggests that DOMVENT3D is mathematically robust and is suitable for modelling a wide variety of dwelling types and geometries to assist engineers and policy makers. Practical application: The modern building services engineer may be required to model airflow networks in a building to balance the conflicting needs of energy consumption reduction and occupant health. Limiting exfiltration is one method of reducing heat losses from a building and so there is a need to model it accurately. This article presents a new model of infiltration and exfiltration through a uniformly porous facade that can be incorporated within advanced complex airflow network tools or applied using a simple spreadsheet.
- 12 August 2013
- Published by SAGE Publications in Building Services Engineering Research & Technology
- Vol. 35 (4) , 408-416
Open AccessModelling uniformly porous facades to predict dwelling infiltration rates
It is important to limit dwelling infiltration to reduce energy demand and help meet national climate change commitments while concurrently providing sufficient ventilation to deliver adequate indoor air quality. DOMVENT3D is a model of infiltration and exfiltration that assumes a linear pressure distribution over any number of uniformly porous facades and integrates the airflow rate in the vertical plane to predict the theoretically correct airflow rate through them. DOMVENT3D is a new development of an existing two-dimensional model of infiltration that provides more opportunities for investigating a greater number of dwellings than was previously possible. Initial testing suggests that DOMVENT3D is mathematically robust and is suitable for modelling a wide variety of dwelling types and geometries to assist engineers and policy makers. Practical application: The modern building services engineer may be required to model airflow networks in a building to balance the conflicting needs of energy consumption reduction and occupant health. Limiting exfiltration is one method of reducing heat losses from a building and so there is a need to model it accurately. This article presents a new model of infiltration and exfiltration through a uniformly porous facade that can be incorporated within advanced complex airflow network tools or applied using a simple spreadsheet.