SCSeok-Kyu Cho

Seok-Kyu Cho

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Seok-Kyu Cho has a total of 47 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Numerical Study on Wave-Absorption Performance of Wave-Absorbing Plates in an Ocean Engineering Basin

    by Kyeonguk Heo, Dong-Min Park, Seok-Kyu Cho

    This study aimed to evaluate the performance of existing wave absorbers in the KRISO ocean engineering basins and to develop an improved design that enhances wave absorption while maximizing usable basin space. Experimental measurements and potential theory calculations were performed to determine the reflection coefficients, applying linear and nonlinear damping models to perforated plates. A multi-domain boundary element method was employed to incorporate these damping models and evaluate various plate configurations. The measured reflection coefficients in both basins were approximately 0.2. For the ocean engineering basin, removing the rear vertical absorber produced negligible changes except in the long-wave region. Analytical results indicated that a double-plate configuration with an inclination angle of 11°–13° and an inter-plate spacing of approximately 0.8 m yielded the lowest reflection coefficient, which was further improved by adopting a parabolic plate profile. These findings demonstrate that an optimized, parabolic double-plate wave absorber can reduce wave reflection substantially and improve basin space utilization. Future computational fluid dynamics analyses and experiments will be conducted to determine the final absorber configuration.

  • Study on the Effect of Catamaran Hull Spacing on Hydrodynamic Characteristics

    by Hyun-Seung Nam, Hyung Do Song, Seok Kyu Cho

    In this study, the hydrodynamic characteristics of a catamaran under zero-speed conditions are investigated with respect to variations in hull spacing. The seakeeping performance of USV catamaran is first analyzed using the frequency-domain analysis program AdFLOW, developed by KRISO, and the numerical results are validated against model test data. The hydrodynamic coefficients are then calculated to examine the influence of the inner free surface. The effects of the resonant modes of the inner free surface and the associated wave field around the catamaran are discussed in detail. Finally, the motion responses of the catamaran are evaluated and compared for different hull spacings and wave directions, providing insights into the hydrodynamic interference between twin hulls.

  • Open Access

    The Optimal Design of an Inclined Porous Plate Wave Absorber Using an Artificial Neural Network Model

    by Senthil Kumar Natarajan, Seokkyu Cho, Il-Hyoung Cho

    This study seeks to optimize the shape of a wave absorber with an inclined porous plate using an artificial neural network (ANN) model to improve the operating efficiency and experimental accuracy of a square wave basin. As our numerical tool, we employed the dual boundary element method (DBEM) to avoid the rank deficiency problem occurring at the degenerate plate boundary with zero thickness. A quadratic velocity model incorporating a CFD-based drag coefficient was employed to account for energy dissipation across the porous plate. The developed DBEM tool was validated through comparisons with self-conducted experiments in a two-dimensional wave flume. The input features such as the inclined angle and plate length affect the performance of the wave absorber. These features have been optimized to minimize the averaged reflection coefficient and the installation space (spatial footprint) with the application of a trained ANN model. The dataset used for training the ANN model was created using the DBEM model. The trained model was subsequently utilized to predict the averaged reflection coefficient using a larger dataset, aiding in the determination of the optimal wave absorber design. In the optimization process of minimizing both reflected waves and spatial footprint, the weighting factors are assigned according to their relative importance to each other, using the weighted sum model (WSM) within the multi-criteria decision-making framework. It was found that the optimal design parameters of the non-dimensional plate length (l/h) and inclined angle (θ) are 1.46 and 5.34° when performing with a weighting factor ratio (80%: 20%) between reflection and spatial footprint.


  • Open Access

    Visualization of Turbulent Flow Fields Around a Circular Cylinder at Reynolds Number 1.4×105 Using PIV

    by Jun-Hee Lee, Bu-Geun Paik, Seok-Kyu Cho, Jae-Hwan Jung

    This study investigates the experimental parameters of particle image velocimetry (PIV) to enhance the measurement technique for turbulent flow fields around a circular cylinder at a Reynolds number (Re) of 1.4×105. At the Korea Research Institute of Ships & Ocean Engineering (KRISO), we utilized the cavitation tunnel and PIV system to capture the instantaneous flow fields and statistically obtained the mean flow fields. An aspect ratio and blockage ratio of 16.7% and 6.0%, respectively, were considered to minimize the tunnel wall effect on the cylinder wakes. The optimal values of the pulse time and the number of flow fields were determined by comparing the contours of mean streamlines, velocities, Reynolds shear stresses, and turbulent kinetic energy under their different values to ensure accurate and converged results. Based on the findings, we recommend a pulse time of 45 μs corresponding to a particle moving time of 3–4 pixels, and at least 3,000 instantaneous flow fields to accurately obtain the mean flow fields. The results of the present study agree well with those of previous studies that examined the end of the subcritical flow regime.


  • Open Access

    Analysis of Relative Wave Elevation Around Semi-submersible Platform Through Model Test: Focusing on Comparison of Wave Probe Characteristics

    by Hyun-Seung Nam, Dong-Min Park, Seok Kyu Cho, Sa Young Hong

    Recently, as the offshore structures are operated in the deep-sea oil fields, interest in the analysis of relative wave elevation around platforms is increased. In this study, it is examined how the analysis results differ depending on the characteristics of the wave probe when interpreting the relative wave elevation in the model test. First, by conducting the wave probe comparison experiment in the two-dimensional wave tank, it is confirmed how the measured values differ according to the type of wave probe for the same physical phenomenon. Two types of wave probe are selected, the resistance type and the capacitance type, and the causes of the difference in measured values is studied. After that, the model test of the semi-submersible platform is conducted to investigate the relative wave elevation. Relative wave elevation is measured with the wave probes used in the wave probe comparison experiment and analyzed to estimate the asymmetric factor and the extreme upwell. The results between the two types of wave probes are compared, and qualitative study for the cause of the difference is conducted by photographing the physical phenomenon using a high-speed camera. Through the above study, it is confirmed that the capacitance type wave probe shows a larger measured value than the resistance type under the breaking-wave condition, and the same results are obtained for the asymmetric factor and the extreme upwell. These results is thought to be due to the difference in the measurement principle between wave probes, which is whether or not they measured water bubbles. This implies that the model test should be conducted using appropriate wave probes by considering the physical phenomenon to be analyzed.


  • Open Access

    Numerical Study on Characteristics and Control of Heading Angle of Floating LNG Bunkering Terminal for Improvement of Loading and Off-loading Performance

    by Seunghoon Oh, Dong-Woo Jung, Yun-Ho Kim, Hyun-Uk Kwak, Jae-Hwan Jung, Sung-Jun Jung, Byeongwon Park, Seok-Kyu Cho, Hong Gun Sung

    Owing to the regulation of exhaust gas emissions from vessels, liquefied natural gas (LNG) has been garnering attention as an alternative eco-friendly fuel for vessels. LNG is considered as one of the most realistic alternatives to satisfy SOx and NOx regulations. Such social awareness is accelerating the development of LNGpowered vessels. It is necessary to expand the LNG bunkering infrastructure to supply LNG to vessels with LNG propulsion for their smooth operation. Relevant studies have been actively conducted both nationally and globally, and their feasibility has been reviewed. The Korea Research Institute of Ships & Ocean Engineering (KRISO) has been conducting studies on an offshore floating LNG bunkering system and has reviewed the system in terms of the design, equipment, and rules for offshore


  • Open Access

    Experimental Study on Estimation of Roll Damping for Various Midship Sections

    by Byeongwon Park, Dong Woo Jung, Jaesag Jung, Inbo Park, Seok-Kyu Cho, Hong Gun Sung

    서 론 해상 유전 개발의 경제성 확보를 위해 오일 메이저 및 국영 석유회사는 저유가 시대에 맞는 저비용 해양플랜트 개발의 필 요성을 제기하고 있다. 특히, 깊은 수심 및 인프라가 부족한 해 역에 주로 투입되는 선박형 부유식 해양구조물인 FPSO(Floating production storage offloading)의 효율적인 설계 및 개발이 대표적 이다. 부유식 해양구조물 설계의 가장 기본이 되는 정보는 대상 부 유체의 파랑 중 동적 거동, 상대 파고 및 가속도 정보이다. 특 히, 부유체의 6자유도 운동 중 횡동요(Roll)는 폭 방향 및 수직 방향으로의 가속도를 유발하는 중요한 인자로 부유체 선체 및 상부의 트러스 구조에 하중을


  • Study on the Motions and Flooding Process of a Damaged Ship in Waves

    by Seokkyu Cho, Honggun Sung, Sayoung Hong, Bowoo Nam, Sungchul Hwang, Youngsik Kim