RZRene Zamora-Cristales

Rene Zamora-Cristales

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Rene Zamora-Cristales has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    North American Forest Biomass Supply Chains for Efficient Bioenergy Production

    by John Sessions, Rene Zamora-Cristales, Robert J. Macias, Andres Susaeta, Francisca Marrs Belart

    Forest bioenergy holds significant potential for North American decarbonization and energy security, yet persistently high logistics costs, feedstock quality variability, and geographic dispersion of biomass resources continue to constrain commercial viability. This review asks what it will take for forest bioenergy supply chains to achieve economic and operational lift-off, identifying key bottlenecks and the most promising pathways to scale. We systematically review 237 peer-reviewed studies and technical reports with the majority published between 2000 and 2025, covering feedstock types ranging from logging residues and woody biomass to short rotation woody crops, and end-products spanning solid biofuels, heat and power, thermochemical products, and sustainable aviation fuel. The literature consistently identifies delivered cost, feedstock quality control, and the geographic mismatch between biomass supply and conversion facility location as the three primary barriers to sector viability. Depot-based preprocessing, cascading utilization strategies, and participatory landowner contracting emerge as the most effective near-term solutions for improving supply chain economics and mobilizing economically recoverable biomass. At the frontier, AI-enabled optimization, digital twin modeling, and integrated biorefinery configurations show strong potential to manage spatial variability and unlock the scale economies on which commercial viability depends. Translating these advances into practice will require stable, long-term policy signals and coordinated investment across the full supply chain.

  • Cost and Productivity of Tethered Cut-to-Length Systems in a Dry-Forest Fuel-Reduction Treatment: A Case Study

    by Joshua Petitmermet, John Sessions, John Bailey, Rene Zamora-Cristales

    Fuel-reduction treatments on steep slopes across federal forests of the western United States have been limited by the high costs associated with cable logging on steeper slopes combined with poor market prospects for small-diameter material (Bolding 2003, Rummer 2008, Han et al. 2016). The emergence of tethered cut-to-length harvesting systems and small wood markets (e.g., biochar) could decrease costs and increase revenue generated from treatments. Over the course of 3 weeks, we observed both tethered (steeper slopes) and untethered cut-to-length fuel-reduction treatment on the Fremont-Winema National Forest in south-central Oregon and interviewed operators. We used those data to derive and contrast hourly costs and productivity for the harvester and forwarder. This was the first time a tethered harvester and forwarder were used in a fuel-reduction treatment on federal forests in this region. We developed and tested a variety of work time model forms for each machine. The mean utilization rate for the harvester was 64 percent on 17 tethered consolidated corridors but 87 percent on 28 untethered consolidated corridors. Similarly, the forwarder had a mean utilization rate of 76 percent on 30 tethered trips and 89 percent on 114 untethered trips. This reduced utilization rate could be because of the direct effects of tethering, the increased complexities of operations associated with steeper slopes, and the stand characteristics (e.g., lower stand density and tree sweep) associated with steeper slopes. Costs during tethered operations were higher than during nontethered operations, but lower than previous reports using cable logging.


  • Open Access

    Improving Large Trailer Access for Biomass Recovery in Steep Terrain

    by Bryent Daugherty, John Sessions, Rene Zamora-Cristales, Michael G Wing

    Between 30 and 40% of private and state forest lands in the US Pacific Northwest are in steep terrain, making forest harvest residues difficult and costly to obtain. Turnarounds in steep terrain are particularly problematic. In 2010, Hermann Brothers Logging (Port Angeles, WA), in collaboration with Western Trailers (Boise, ID), designed a self-steering chip van to increase large trailer access in steep areas of the Olympic Peninsula (WA). Following a series of mobility tests of the self-steering trailer, Arena Simulation by Rockwell Automation was used to compare the self-steering trailer system cost-effectiveness against a hook-lift truck system on a total system cost BDMt-1 basis. Under a base scenario, the self-steering system had a lower cost ($60.01 BDMt-1) than the hook-lift truck application ($101.27 BDMt-1) with a total system cost, including mobilization, piling, support equipment, and profit and risk. Assuming a 13.72 m (45 ft) standard trailer could reach a percentage of the harvest units, the hook-lift/standard trailer combination system was still not competitive with the self-steering trailer under the base case scenario until the percent allocation for the hook-lift trucks was reduced to 13%. After altering the base case scenario to favor the hook-lift application, the self-steering system was still more cost-effective until the allocation for hook-lift trucks was reduced to 21%.


  • Open Access

    Economic Estimation of the Available Biomass following Logging Operations in Western Oregon and Washington

    by Rene Zamora-Cristales, Kevin Boston, Justin Long, John Sessions

    A two-step method was developed to estimate the economically available biomass from forest operations in the Pacific Northwest. Step 1 measures the amount of biomass in piles from a variety of logging operations. Step 2 applies logistics models to determine the amount of biomass that is recoverable by computing the extraction costs depending on the distance from the landing. Cable units included only the biomass piles located at the landings, while ground-based units computed the collection and transport of each pile to the most cost-effective landing using geographic information system and simulation tools. This approach was applied to operations on state and private timberlands in Oregon and Washington. For the cable logging units, the average pile size was 46.7 green tonnes of residue, and this material was either on or next to the roadside landing. It produced few large piles with an average of 24.75 green tonnes per ha. For ground-based operations, approximately 54 percent of the residue in the harvest units was 90 m or less from the landing. Collection cost increases as the material is farther from the landing and ranged between about $17.6 per green tonne at distances of 15.2 m to $37 per green tonne at distances of 213 m from the landing. Depending on the distance from the landing to the bioenergy facility, it is possible to estimate how far from the landing into the forest to reach to economically collect the biomass.


  • Open Access

    Subregional Comparison for Forest- to-Product Biomass Supply Chains on the Pacific West Coast, USA

    by Michael David Berry, John Sessions, Rene Zamora-Cristales

    : Transportable biomass conversion facilities producing biochar, briquettes, and torrefied wood are modeled and optimized for five different sub-regions within the Pacific Northwest. Subregional case studies in Quincy, California; Lakeview, Oregon; Oakridge, Oregon; Port Angeles, Washington; and Warm Springs, Oregon, are evaluated to characterize the potential economic viability of these novel transportable designs. A mixed integer program is used to characterize the supply chain from residue extraction to market optimizing transportation, production, and plant mobility in order to minimize the supply chain costs. Regional variations including log specifications, energy rates, trucking, and logistic capacities are considered within the model and supporting analyses to differentiate regional costs and market viabilities. It was found that the optimal transportable design included facility movement on a 1 to 2.5 year frequency depending on product and region with biochar being the most likely to be economically viable. Regional feedstock composition and availability was the biggest indicator of lower cost production. Supply chain costs varied by 5%-10% depending on product and region being produced. Transportation and mobilization were found to account for 15%-30% of the overall supply chain cost. Quincy, California, and torrefied wood were found to have the lowest of these costs due to low move frequency and high wood availability while Port Angeles, Washington, with briquettes was the highest. With regards to fuel price sensitivity, torrefied wood was the most sensitive as its conversion process was most energy intensive (±12%-13%) and biochar least sensitive (±3-5%).Transportation accounted for 5% to 30% of the fuel price variation due to diesel prices depending on product and region. When including grid-connectivity, cost reductions were approximately 6%-7% for biochar, 27%-29% for briquettes and 33%-38% for torrefied wood. These findings indicate biochar as the most likely candidate for a transportable conversion system given its relatively low power consumption, high allowable moisture content, and low product transportation cost. Quincy, California, was found to be the most desirable sub region with the lowest overall production costs attributed to its high input quality feedstock and relative accessibility; its higher grid-connected power cost also makes transportable options relatively more attractive than other off-grid locations. Port Angeles, WA had the highest production costs and lowest grid-energy costs. Our results indicate that a rise in diesel price, while incentivizing transportable conversion facilities due to more cost effective transportation, would be more than offset by the higher cost energy consumption during the conversion process when compared with grid-power with the potential exception of biochar. Overall, we see a transportable operation with grid-power would likely be the difference between an economically viable supply chain and one that is not. Keywords: Biomass supply, Biomass products, Facility location, Mixed integer programming, Strategic planning, Transportable plants.


  • Open Access

    Modeling the Processing and Transportation Logistics of Forest Residues Using Life Cycle Assessment

    by Cindy X. Chen, Francesca Pierobon, Rene Zamora-Cristales, Indroneil Ganguly, John Sessions, Ivan Eastin

    This study investigates the environmental burdens of three logistics system scenarios for residue processing and transportation under different road type distri


  • Open Access

    Economic implications of grinding, transporting, and pretreating fresh versus aged forest residues for biofuel production

    by Rene Zamora-Cristales, John Sessions, Gevan Marrs

    The moisture content in forest harvest residues is a key factor affecting the supply cost for bioenergy production. Fresh harvest residues tend to contain higher amounts of water, thus making transportation inefficient. Additionally, fresh harvest residues contain greater amounts of needles and bark that may reduce the polysaccharide content, thus affecting the production of liquid fuels derived from cellulosic components. In this study, we estimated the downstream economic effect in the supply chain of collecting, grinding, transporting and pretreating fresh versus aged residues. Specifically, we analyzed the effect of feedstock moisture content on grinder fuel consumption, bulk density, bark and needle content, and polysaccharide proportion. Fresh forest harvest residues were 60% moisture content (wet basis) and aged forest residues were 15% moisture content. The bark and needle proportion is 6.1% higher in fresh residue than in aged residue. Polysaccharides were 26% higher in aged residue than in fresh residue. On a dry-tonne basis, the cost of grinding fresh residues was about the same as that of aged residues. However, considering the difference in bulk density on transportation cost and the difference in polysaccharide yield, the value gain for in-field drying ranges from US$29.60 to US$74.90 per ovendry tonne.