Henning Weinrich
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Henning Weinrich has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Hermann Tempel
Institute of Energy Technologies – Fundamental Electrochemistry (IET‐1) Forschungszentrum Jülich Jülich Germany
15 shared publications - Rüdiger-Albert Eichel
Forschungszentrum Jülich
13 shared publications - Hans Kungl
Institute of Energy Technologies - Fundamental Electrochemistry (IET-1), Forschungszentrum Jülich GmbH, Wilhelm-Johnen-Straße, 52425 Jülich, Germany
11 shared publications Bernhard Schmid
Institute of Energy and Climate Research − Fundamental Electrochemistry (IEK-9), Forschungszentrum Jülich GmbH, 52428 Jülich, Germany
4 shared publications- Ansgar Kretzschmar
Forschungszentrum Jülich GmbH (IET-1)
3 shared publications - Markus Gehring
Forschungszentrum Jülich GmbH
3 shared publications
Latest Publications
- Open Access
- 7 May 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (14) , 6854-6873
Closing the carbon cycle: challenges and opportunities of CO 2 electrolyser designs in light of cross-industrial CO 2 source-sink matching in the European landscape
Defossilising the industrial sector is crucial for climate neutrality. A comprehensive analysis assesses cross-industrial CO 2 capture/utilisation via electrolysis, focusing on source-sink matching strategies within the European chemical industry.
- 7 May 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (14) , 6854-6873
Open AccessClosing the carbon cycle: challenges and opportunities of CO 2 electrolyser designs in light of cross-industrial CO 2 source-sink matching in the European landscape
Defossilising the industrial sector is crucial for climate neutrality. A comprehensive analysis assesses cross-industrial CO 2 capture/utilisation via electrolysis, focusing on source-sink matching strategies within the European chemical industry.
- Open Access
- 22 February 2024
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 63 (9) , 3986-3996
Impact of the PiperION Anion Exchange Membrane Thickness on the Performance of a CO2-to-HCOOH Three-Compartment Electrolyzer
- 22 February 2024
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 63 (9) , 3986-3996
Open AccessImpact of the PiperION Anion Exchange Membrane Thickness on the Performance of a CO2-to-HCOOH Three-Compartment Electrolyzer
- Open Access
- 14 February 2024
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 8 (7) , 1483-1494
Early-stage performance change of gas diffusion electrodes for CO 2 electroreduction to formate
Gas diffusion electrodes used for CO 2 electroreduction to formate are still inadequate regarding lifetime and stability. Here catalyst agglomeration and loss of hydrophobicity were identified as reasons for early-stage performance changes.
- 14 February 2024
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 8 (7) , 1483-1494
Open AccessEarly-stage performance change of gas diffusion electrodes for CO 2 electroreduction to formate
Gas diffusion electrodes used for CO 2 electroreduction to formate are still inadequate regarding lifetime and stability. Here catalyst agglomeration and loss of hydrophobicity were identified as reasons for early-stage performance changes.
- Open Access
- 28 July 2023
- Published by Wiley in ChemElectroChem
- Vol. 10 (17)
Impact of the Carbon Substrate for Gas Diffusion Electrodes on the Electroreduction of CO2 to Formate
Aiming to advance the technical maturity of CO2 electrolysis to formic acid, various gas diffusion layers (GDLs) are investigated for their suitability as carbon‐based substrate for gas diffusion electrodes (GDEs) and their effect on the electroreduction of CO2 to formate. Particular attention lies on the elucidation for the effect of the GDL thickness, hydrophobic treatment, and presence of a microporous layer (MPL) on the GDE performance in terms of Faradaic efficiency. Based on the investigation it is found that the GDL thickness has no discernible influence on the Faradaic efficiency, while a GDE with a hydrophobic treatment of 10 % PTFE outperforms a GDE based on a GDL with 30 % PTFE. Furthermore, the presence of a MPL is found to be of marked importance to achieve relevant current densities given its effect on the focus of the catalyst layer on the GDE surface after spray coating, the wetting, and the electrical conductivity.
- 28 July 2023
- Published by Wiley in ChemElectroChem
- Vol. 10 (17)
Open AccessImpact of the Carbon Substrate for Gas Diffusion Electrodes on the Electroreduction of CO2 to Formate
Aiming to advance the technical maturity of CO2 electrolysis to formic acid, various gas diffusion layers (GDLs) are investigated for their suitability as carbon‐based substrate for gas diffusion electrodes (GDEs) and their effect on the electroreduction of CO2 to formate. Particular attention lies on the elucidation for the effect of the GDL thickness, hydrophobic treatment, and presence of a microporous layer (MPL) on the GDE performance in terms of Faradaic efficiency. Based on the investigation it is found that the GDL thickness has no discernible influence on the Faradaic efficiency, while a GDE with a hydrophobic treatment of 10 % PTFE outperforms a GDE based on a GDL with 30 % PTFE. Furthermore, the presence of a MPL is found to be of marked importance to achieve relevant current densities given its effect on the focus of the catalyst layer on the GDE surface after spray coating, the wetting, and the electrical conductivity.
- Open Access
CO2 Electroreduction to Formate—Comparative Study Regarding the Electrocatalytic Performance of SnO2 Nanoparticles
SnO2 nanoparticles have frequently been reported as effective electrocatalysts for CO2 electroreduction to formate. However, in the literature, there is little knowledge of SnO2 nanoparticles that guarantee superior electrocatalytic performance. Hence, in this study, several SnO2 nanoparticles are compared with respect to their material properties, and correlations to the electrocatalytic performance are established. For comparison, three custom-made SnO2-electrocatalysts were prepared, reproducing frequently cited procedures in literature. Based on the comparison, it is found that hydrothermal, sol-gel, and solid-state synthesis provide quite different electrocatalysts, particularly in terms of the particle size and crystal lattice defect structure. Desirably small nanoparticles with a comparatively high number of lattice defects are found for the nanoparticles prepared by hydrothermal synthesis, which also provide the best electrocatalytic performance in terms of Faradaic efficiency for the electroreduction of CO2 to formate. However, despite the considerably smaller surface area, the commercial reference also provides significant electrocatalytic performance, e.g., in terms of the overall produced amount of formate, which suggests a surprisingly high surface area-specific activity for this material that is low on defects. Thus, defects do not appear to be the preferred reaction site for the CO2 electroreduction to formate on SnO2 in this case.
Open AccessCO2 Electroreduction to Formate—Comparative Study Regarding the Electrocatalytic Performance of SnO2 Nanoparticles
SnO2 nanoparticles have frequently been reported as effective electrocatalysts for CO2 electroreduction to formate. However, in the literature, there is little knowledge of SnO2 nanoparticles that guarantee superior electrocatalytic performance. Hence, in this study, several SnO2 nanoparticles are compared with respect to their material properties, and correlations to the electrocatalytic performance are established. For comparison, three custom-made SnO2-electrocatalysts were prepared, reproducing frequently cited procedures in literature. Based on the comparison, it is found that hydrothermal, sol-gel, and solid-state synthesis provide quite different electrocatalysts, particularly in terms of the particle size and crystal lattice defect structure. Desirably small nanoparticles with a comparatively high number of lattice defects are found for the nanoparticles prepared by hydrothermal synthesis, which also provide the best electrocatalytic performance in terms of Faradaic efficiency for the electroreduction of CO2 to formate. However, despite the considerably smaller surface area, the commercial reference also provides significant electrocatalytic performance, e.g., in terms of the overall produced amount of formate, which suggests a surprisingly high surface area-specific activity for this material that is low on defects. Thus, defects do not appear to be the preferred reaction site for the CO2 electroreduction to formate on SnO2 in this case.
- Open Access
- 24 May 2022
- Published by Wiley in ChemSusChem
- Vol. 15 (14) , e202200761
CO2/N2 Separation on Highly Selective Carbon Nanofibers Investigated by Dynamic Gas Adsorption
The development of highly selective adsorbents for CO2 is a key part to advance separation by adsorption as a viable technique for CO2 capture. In this work, polyacrylonitrile (PAN) based carbon nanofibers (CNFs) were investigated for their CO2 separation capabilities using dynamic gas adsorption. The CNFs were prepared by electrospinning and subsequent carbonization at various temperatures ranging from 600 to 1000 °C. A thorough investigation of the CO2/N2 selectivity resulted in measured values of 53–106 at 1 bar and 25 °C on CNFs carbonized at 600, 700, or 800 °C. Moreover, the selectivity increased with lower measurement temperatures and lower CO2 partial pressures, reaching values up to 194. Further analysis revealed high long‐term stability with no degradation over 300 cycles and fast adsorption kinetics for CNFs carbonized at 600 or 700 °C. These excellent properties make PAN‐based CNFs carbonized at 600 or 700 °C promising candidates for the capture of CO2.
- 24 May 2022
- Published by Wiley in ChemSusChem
- Vol. 15 (14) , e202200761
Open AccessCO2/N2 Separation on Highly Selective Carbon Nanofibers Investigated by Dynamic Gas Adsorption
The development of highly selective adsorbents for CO2 is a key part to advance separation by adsorption as a viable technique for CO2 capture. In this work, polyacrylonitrile (PAN) based carbon nanofibers (CNFs) were investigated for their CO2 separation capabilities using dynamic gas adsorption. The CNFs were prepared by electrospinning and subsequent carbonization at various temperatures ranging from 600 to 1000 °C. A thorough investigation of the CO2/N2 selectivity resulted in measured values of 53–106 at 1 bar and 25 °C on CNFs carbonized at 600, 700, or 800 °C. Moreover, the selectivity increased with lower measurement temperatures and lower CO2 partial pressures, reaching values up to 194. Further analysis revealed high long‐term stability with no degradation over 300 cycles and fast adsorption kinetics for CNFs carbonized at 600 or 700 °C. These excellent properties make PAN‐based CNFs carbonized at 600 or 700 °C promising candidates for the capture of CO2.
- Open Access
- 6 April 2022
- Published by Wiley in Batteries & Supercaps
- Vol. 5 (5)
In Situ Hydrogen Evolution Monitoring During the Electrochemical Formation and Cycling of Pressed‐Plate Carbonyl Iron Electrodes in Alkaline Electrolyte
Invited for this month's cover picture is the institute of Rüdiger‐A. Eichel. The cover picture illustrates the hydrogen evolution on carbonyl iron electrodes, with the latter being a resource‐efficient option to store renewable electricity for stationary applications effectively, if an appropriate charging protocol is applied. Read the full text of the Research Article at 10.1002/batt.202100415.
- 6 April 2022
- Published by Wiley in Batteries & Supercaps
- Vol. 5 (5)
Open AccessIn Situ Hydrogen Evolution Monitoring During the Electrochemical Formation and Cycling of Pressed‐Plate Carbonyl Iron Electrodes in Alkaline Electrolyte
Invited for this month's cover picture is the institute of Rüdiger‐A. Eichel. The cover picture illustrates the hydrogen evolution on carbonyl iron electrodes, with the latter being a resource‐efficient option to store renewable electricity for stationary applications effectively, if an appropriate charging protocol is applied. Read the full text of the Research Article at 10.1002/batt.202100415.
- Open Access
- 2 February 2022
- Published by Wiley in Batteries & Supercaps
- Vol. 5 (5)
In Situ Hydrogen Evolution Monitoring During the Electrochemical Formation and Cycling of Pressed‐Plate Carbonyl Iron Electrodes in Alkaline Electrolyte
The hydrogen evolution reaction (HER) on iron is a parasitic side reaction for the reduction of iron (hydr)oxide in alkaline electrolyte, which lowers the Coulombic efficiency of iron‐based batteries. Tackling this issue, here we investigate the HER on iron electrodes by in situ gas chromatography, allowing for a quantitative correlation of the applied electrode potential and the resulting hydrogen evolution. As a result, it is shown that the HER follows a distinctive profile corresponding to the electrode potential and changes depending on the state of the iron electrode formation. Moreover, it is shown that the charging efficiency of the iron electrode can be increased by an alteration of the charging procedure, i. e., a more negative cut‐off potential for the discharge and a potential limitation for the recharge. In this study, a charging efficiency of 96.7 % is achieved, using an optimized charging procedure for a formed carbonyl iron electrode containing 8.5 wt.% of Bi2S3.
- 2 February 2022
- Published by Wiley in Batteries & Supercaps
- Vol. 5 (5)
Open AccessIn Situ Hydrogen Evolution Monitoring During the Electrochemical Formation and Cycling of Pressed‐Plate Carbonyl Iron Electrodes in Alkaline Electrolyte
The hydrogen evolution reaction (HER) on iron is a parasitic side reaction for the reduction of iron (hydr)oxide in alkaline electrolyte, which lowers the Coulombic efficiency of iron‐based batteries. Tackling this issue, here we investigate the HER on iron electrodes by in situ gas chromatography, allowing for a quantitative correlation of the applied electrode potential and the resulting hydrogen evolution. As a result, it is shown that the HER follows a distinctive profile corresponding to the electrode potential and changes depending on the state of the iron electrode formation. Moreover, it is shown that the charging efficiency of the iron electrode can be increased by an alteration of the charging procedure, i. e., a more negative cut‐off potential for the discharge and a potential limitation for the recharge. In this study, a charging efficiency of 96.7 % is achieved, using an optimized charging procedure for a formed carbonyl iron electrode containing 8.5 wt.% of Bi2S3.
- Open Access
- 26 March 2020
- Published by Wiley in ChemSusChem
- Vol. 13 (12) , 3180-3191
Tailored Gas Adsorption Properties of Electrospun Carbon Nanofibers for Gas Separation and Storage
Carbon nanofibers (CNFs) derived from electrospun polyacrylonitrile (PAN) were investigated with respect to their gas adsorption properties. By employing CO2 adsorption measurements, it is shown that the adsorption capacity and selectivity of the fibers can be tailored by means of the applied carbonization temperature. General pore properties of the CNFs were identified by Ar adsorption measurements, whereas CO2 adsorption measurements provided information about the ultramicroporosity, adsorption energies, and adsorption capacities. Ideal adsorbed solution theory (IAST) selectivities under practically relevant conditions were determined by evaluation of single‐component data for N2 and CO2. Especially for low carbonization temperatures, the CNFs exhibit very good low‐pressure adsorption performance and excellent CO2/N2 IAST selectivities of 350 at 20 mbar and 132 at 1 bar, which are attributed to a molecular‐sieve effect in very narrow slit pores. These IAST selectivities are some of the highest values for carbon materials reported in the literature so far and the highest IAST selectivities for as‐prepared, non‐post‐treated carbon ever.
- 26 March 2020
- Published by Wiley in ChemSusChem
- Vol. 13 (12) , 3180-3191
Open AccessTailored Gas Adsorption Properties of Electrospun Carbon Nanofibers for Gas Separation and Storage
Carbon nanofibers (CNFs) derived from electrospun polyacrylonitrile (PAN) were investigated with respect to their gas adsorption properties. By employing CO2 adsorption measurements, it is shown that the adsorption capacity and selectivity of the fibers can be tailored by means of the applied carbonization temperature. General pore properties of the CNFs were identified by Ar adsorption measurements, whereas CO2 adsorption measurements provided information about the ultramicroporosity, adsorption energies, and adsorption capacities. Ideal adsorbed solution theory (IAST) selectivities under practically relevant conditions were determined by evaluation of single‐component data for N2 and CO2. Especially for low carbonization temperatures, the CNFs exhibit very good low‐pressure adsorption performance and excellent CO2/N2 IAST selectivities of 350 at 20 mbar and 132 at 1 bar, which are attributed to a molecular‐sieve effect in very narrow slit pores. These IAST selectivities are some of the highest values for carbon materials reported in the literature so far and the highest IAST selectivities for as‐prepared, non‐post‐treated carbon ever.