Fei Gao
Research Subjects
Fei Gao has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Arthur Y. Baranovskiy
Energy and Environmental Directorate, Pacific Northwest National Laboratory, Richland, USA
1 shared publicationCassidy S. Anderson
Energy and Environmental Directorate, Pacific Northwest National Laboratory, Richland, USA
1 shared publicationChaojiang Niu
Energy and Environmental Directorate, Pacific Northwest National Laboratory, Richland, USA
1 shared publicationChengqi Wang
Department of Nuclear Engineering and Radiological Sciences, University of Michigan, Ann Arbor, USA
1 shared publicationDianying Liu
Energy and Environmental Directorate, Pacific Northwest National Laboratory, Richland, USA
1 shared publication- Dongping Lu
Energy and Environment Directorate Pacific Northwest National Laboratory Richland WA 99354 USA
1 shared publication
Latest Publications
- 4 September 2020
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 13 (10) , 3620-3632
Reaction heterogeneity in practical high-energy lithium–sulfur pouch cells
The lithium–sulfur (Li–S) battery is a promising next-generation energy storage technology because of its high theoretical energy and low cost. Extensive research efforts have been made on new materials and advanced characterization techniques for mechanistic studies. However, it is uncertain how discoveries made on the material level apply to realistic batteries due to limited analysis and characterization of real high-energy cells, such as pouch cells. Evaluation of pouch cells (>1 A h) (instead of coin cells) that are scalable to practical cells provides a critical understanding of current limitations which enables the proposal of strategies and solutions for further performance improvement. Herein, we design and fabricate pouch cells over 300 W h kg−1, compare the cell parameters required for high-energy pouch cells, and investigate the reaction processes and their correlation to cell cycling behavior and failure mechanisms. Spatially resolved characterization techniques and fluid-flow simulation reveal the impacts of the liquid electrolyte diffusion within the pouch cells. We found that catastrophic failure of high-energy Li–S pouch cells results from uneven sulfur/polysulfide reactions and electrolyte depletion for the first tens of cycles, rather than sulfur dissolution as commonly reported in the literature. The uneven reaction stems from limited electrolyte diffusion through the porous channels into the central part of thick cathodes during cycling, which is amplified both across the sulfur electrodes and within the same electrode plane. A combination of strategies is suggested to increase sulfur utilization, improve nanoarchitectures for electrolyte diffusion and reduce consumption of the electrolytes and additives.
- 4 September 2020
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 13 (10) , 3620-3632
Reaction heterogeneity in practical high-energy lithium–sulfur pouch cells
The lithium–sulfur (Li–S) battery is a promising next-generation energy storage technology because of its high theoretical energy and low cost. Extensive research efforts have been made on new materials and advanced characterization techniques for mechanistic studies. However, it is uncertain how discoveries made on the material level apply to realistic batteries due to limited analysis and characterization of real high-energy cells, such as pouch cells. Evaluation of pouch cells (>1 A h) (instead of coin cells) that are scalable to practical cells provides a critical understanding of current limitations which enables the proposal of strategies and solutions for further performance improvement. Herein, we design and fabricate pouch cells over 300 W h kg−1, compare the cell parameters required for high-energy pouch cells, and investigate the reaction processes and their correlation to cell cycling behavior and failure mechanisms. Spatially resolved characterization techniques and fluid-flow simulation reveal the impacts of the liquid electrolyte diffusion within the pouch cells. We found that catastrophic failure of high-energy Li–S pouch cells results from uneven sulfur/polysulfide reactions and electrolyte depletion for the first tens of cycles, rather than sulfur dissolution as commonly reported in the literature. The uneven reaction stems from limited electrolyte diffusion through the porous channels into the central part of thick cathodes during cycling, which is amplified both across the sulfur electrodes and within the same electrode plane. A combination of strategies is suggested to increase sulfur utilization, improve nanoarchitectures for electrolyte diffusion and reduce consumption of the electrolytes and additives.
- 22 October 2019
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 11 (43) , 20754-20765
Proton irradiation of graphene: insights from atomistic modeling
Various types of topological defects are produced during proton irradiation, which are crucial in functionalizing graphene, but the mechanisms of the defect generation process and the structure change are still elusive. Herein, we investigated the graphene defect generation probabilities and defect structures under proton irradiation using both ab initio and classical molecular dynamics simulations. As the proton energy increases from 0.1 keV to 100 keV, defect structures transition from single vacancy and Frenkel pairs to a rich variety of topological defects with the possibility of ejecting multiple atoms. We show that, relatively good agreement on defect generation probabilities can be reached between the two simulation approaches at a proton energy of 1 and 10 keV. However, at 0.1 keV, the single vacancy generation probability differs significantly in two methods due to the difference in the energy required to form single vacancy. Using the classical molecular dynamics simulation, we also studied the evolution of different types of defects and the dependence of their probabilities of occurrence on the proton energy and incident angle. The correlation between the impact positions and defect types allows for the convoluted relationship between the defect probabilities, geometric parameters, and proton energy to be elucidated. We show that the proton energy and incident angle can be used to effectively tune the generation probabilities of different types of defects. Our results provide insights into the controlled defect engineering through ion irradiation, which will be useful for the development of functionalized graphene and graphene electronics.
- 22 October 2019
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 11 (43) , 20754-20765
Proton irradiation of graphene: insights from atomistic modeling
Various types of topological defects are produced during proton irradiation, which are crucial in functionalizing graphene, but the mechanisms of the defect generation process and the structure change are still elusive. Herein, we investigated the graphene defect generation probabilities and defect structures under proton irradiation using both ab initio and classical molecular dynamics simulations. As the proton energy increases from 0.1 keV to 100 keV, defect structures transition from single vacancy and Frenkel pairs to a rich variety of topological defects with the possibility of ejecting multiple atoms. We show that, relatively good agreement on defect generation probabilities can be reached between the two simulation approaches at a proton energy of 1 and 10 keV. However, at 0.1 keV, the single vacancy generation probability differs significantly in two methods due to the difference in the energy required to form single vacancy. Using the classical molecular dynamics simulation, we also studied the evolution of different types of defects and the dependence of their probabilities of occurrence on the proton energy and incident angle. The correlation between the impact positions and defect types allows for the convoluted relationship between the defect probabilities, geometric parameters, and proton energy to be elucidated. We show that the proton energy and incident angle can be used to effectively tune the generation probabilities of different types of defects. Our results provide insights into the controlled defect engineering through ion irradiation, which will be useful for the development of functionalized graphene and graphene electronics.