Bala Vaidhyanathan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bala Vaidhyanathan has a total of 191 co-authors. Here are the top co-authors by number of shared publications:
- Athanasios Goulas
Department of Materials, Loughborough University, Loughborough LE11 3TU, UK
4 shared publications - Sina Saremi-Yarahmadi
Loughborough University
3 shared publications A. Goulas
Department of Materials, Loughborough University, Loughborough, Leicestershire, LE11 3TU
2 shared publicationsB. Ozkan
Department of Materials, Loughborough University, Loughborough, Leicestershire, LE11 3TU
2 shared publications- Dongrui Xie
School of Metallurgy and Materials University of Birmingham Edgbaston B15 2SE UK
2 shared publications J. Binner
2 shared publications
Latest Publications
- Open Access
- 15 September 2026
- Published by Elsevier in Materials & Design
- Vol. 270
Bio-based photocurable binder design for vat photopolymerisation 3D printing of advanced ceramics
- 15 September 2026
- Published by Elsevier in Materials & Design
- Vol. 270
Open AccessBio-based photocurable binder design for vat photopolymerisation 3D printing of advanced ceramics
- 29 June 2026
- Published by Knowledge E DMCC
Chapter 11: Nano Plants (Nanostructured Implants)
- 29 June 2026
- Published by Knowledge E DMCC
Prototypes for Humanity 2025: Short Papers Platform Conference Proceedings
- 29 June 2026
- Published by Knowledge E DMCC
Prototypes for Humanity 2025: Short Papers Platform Conference Proceedings
- Open Access
- 19 June 2026
- Published by Elsevier in Materials & Design
- Vol. 268
Progress in binder jet 3D printing of advanced ceramics: An insightful review
- 19 June 2026
- Published by Elsevier in Materials & Design
- Vol. 268
Open AccessProgress in binder jet 3D printing of advanced ceramics: An insightful review
- Open Access
- 3 April 2025
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 22 (4)
Field‐assisted processing of Ce–zirconolite ceramics for nuclear applications
Conventional, flash, and hybrid sintering (unique combination of conventional and microwave heating) experiments were performed on 10% Ce‐doped zirconolite samples and the results were compared. Ce–zirconolite was prepared using reactive, pressure‐less, field‐assisted hybrid processing directly from the precursor made using commercial chemical agents, viz., CaTiO3, ZrO2, TiO2, and CeO2 at 1350°C/2 h. For comparison, Ce–zirconolite ceramics were produced by the conventional synthesis at 1350°C/72 h and then sintering at 1450°C/10 h based on a literature methodology. The Ce–zirconolite samples were also flash sintered for the first time at 1100°C in just 5 min with the application of an AC field to ∼98% density with a finer grain size. A novel reactive flash synthesis procedure of zirconolite precursors with subsequent flash sintering was also explored. The flash process for both synthesis/sintering needs only ∼15% of the energy (85% savings) and hybrid method requires ∼ 33% (67% savings) of the total energy, respectively, when compared to the values reported for conventional synthesis and sintering processes together for zirconolite manufacturing. Thus, both the field‐assisted processing techniques were found to be highly energy efficient for the fabrication of Ce‐zirconolite ceramics, making them suitable for applications in Plutonium‐based nuclear waste disposal.
- 3 April 2025
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 22 (4)
Open AccessField‐assisted processing of Ce–zirconolite ceramics for nuclear applications
Conventional, flash, and hybrid sintering (unique combination of conventional and microwave heating) experiments were performed on 10% Ce‐doped zirconolite samples and the results were compared. Ce–zirconolite was prepared using reactive, pressure‐less, field‐assisted hybrid processing directly from the precursor made using commercial chemical agents, viz., CaTiO3, ZrO2, TiO2, and CeO2 at 1350°C/2 h. For comparison, Ce–zirconolite ceramics were produced by the conventional synthesis at 1350°C/72 h and then sintering at 1450°C/10 h based on a literature methodology. The Ce–zirconolite samples were also flash sintered for the first time at 1100°C in just 5 min with the application of an AC field to ∼98% density with a finer grain size. A novel reactive flash synthesis procedure of zirconolite precursors with subsequent flash sintering was also explored. The flash process for both synthesis/sintering needs only ∼15% of the energy (85% savings) and hybrid method requires ∼ 33% (67% savings) of the total energy, respectively, when compared to the values reported for conventional synthesis and sintering processes together for zirconolite manufacturing. Thus, both the field‐assisted processing techniques were found to be highly energy efficient for the fabrication of Ce‐zirconolite ceramics, making them suitable for applications in Plutonium‐based nuclear waste disposal.
- Open Access
- 28 December 2024
- Published by MDPI AG in Micromachines
- Vol. 16 (1) , 30
Additive Manufacturing of Smart Footwear Components for Healthcare Applications
Diabetic foot complications pose significant health risks, necessitating innovative approaches in orthotic design. This study explores the potential of additive manufacturing in producing functional footwear components with lattice-based structures for diabetic foot orthoses. Five distinct lattice structures (gyroid, diamond, Schwarz P, Split P, and honeycomb) were designed and fabricated using stereolithography (SLA) with varying strand thicknesses and resin types. Mechanical testing revealed that the Schwarz P lattice exhibited superior compressive strength, particularly when fabricated with flexible resin. Porosity analysis demonstrated significant variations across structures, with the gyroid showing the most pronounced changes with increasing mesh thickness. Real-time pressure distribution mapping, achieved through integrated force-sensitive resistors and Arduino-based data acquisition, enabled the visualization of pressure hotspots across the insole. The correlation between lattice properties and pressure distribution was established, allowing for tailored designs that effectively alleviated high-pressure areas. This study demonstrates the feasibility of creating highly personalized orthotic solutions for diabetic patients using additive manufacturing, offering a promising approach to reducing the plantar pressure in foot and may contribute to improved outcomes in diabetic foot care.
- 28 December 2024
- Published by MDPI AG in Micromachines
- Vol. 16 (1) , 30
Open AccessAdditive Manufacturing of Smart Footwear Components for Healthcare Applications
Diabetic foot complications pose significant health risks, necessitating innovative approaches in orthotic design. This study explores the potential of additive manufacturing in producing functional footwear components with lattice-based structures for diabetic foot orthoses. Five distinct lattice structures (gyroid, diamond, Schwarz P, Split P, and honeycomb) were designed and fabricated using stereolithography (SLA) with varying strand thicknesses and resin types. Mechanical testing revealed that the Schwarz P lattice exhibited superior compressive strength, particularly when fabricated with flexible resin. Porosity analysis demonstrated significant variations across structures, with the gyroid showing the most pronounced changes with increasing mesh thickness. Real-time pressure distribution mapping, achieved through integrated force-sensitive resistors and Arduino-based data acquisition, enabled the visualization of pressure hotspots across the insole. The correlation between lattice properties and pressure distribution was established, allowing for tailored designs that effectively alleviated high-pressure areas. This study demonstrates the feasibility of creating highly personalized orthotic solutions for diabetic patients using additive manufacturing, offering a promising approach to reducing the plantar pressure in foot and may contribute to improved outcomes in diabetic foot care.
- Open Access
- 30 August 2024
- Published by Elsevier in Additive Manufacturing
- Vol. 92
A low-loss and medium dielectric permittivity SrTiO3/HIPS composite for rapid prototyping of next-generation microwave devices
- 30 August 2024
- Published by Elsevier in Additive Manufacturing
- Vol. 92
Open AccessA low-loss and medium dielectric permittivity SrTiO3/HIPS composite for rapid prototyping of next-generation microwave devices
- Open Access
- 14 June 2024
- Published by Elsevier in Applied Materials Today
- Vol. 39
Digital light processing of sodium-beta-alumina ceramic electrolytes
- 14 June 2024
- Published by Elsevier in Applied Materials Today
- Vol. 39
Open AccessDigital light processing of sodium-beta-alumina ceramic electrolytes
- Open Access
- 23 February 2024
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 44 (8) , 5041-5047
Rapid manufacture of sodium polyaluminate electrolyte ceramics for solid state batteries via direct ink writing
- 23 February 2024
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 44 (8) , 5041-5047
Open AccessRapid manufacture of sodium polyaluminate electrolyte ceramics for solid state batteries via direct ink writing
- 1 February 2021
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 41 (2) , 1427-1437
The ballistic impact performance of nanocrystalline zirconia-toughened alumina (nZTA) and alumina ceramics
- 1 February 2021
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 41 (2) , 1427-1437
The ballistic impact performance of nanocrystalline zirconia-toughened alumina (nZTA) and alumina ceramics