Serhii Chernenko
Research Subjects
Research Interests
Serhii Chernenko has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Eduard Klimov
Department of Automobiles and Tractors, Kremenchuk Mykhailo Ostrohradskyi National University, 39600 Kremenchuk, Ukraine
10 shared publications - Andrii Chernysh
Kremenchuk Mykhailo Ostrohradskyi National University
6 shared publications - Olexandr Pavlenko
Kremenchuk Mykhailo Ostrohradskyi National University,Department of automobiles and tractors,Kremenchuk,Ukraine
3 shared publications - Ruslan Puzyr
Kremenchuk Mykhailo Ostrohradskyi National University
3 shared publications - Volodymyr Kukhar
Department of Metallurgy and Innovative Technologies, Technical University “Metinvest Polytechnic” LLC, 69008 Zaporizhzhia, Ukraine
3 shared publications - Olexandr Kharkov
Kremenchuk Mykhailo Ostrohradskyi National University,Department of automobiles and tractors,Kremenchuk,Ukraine
2 shared publications
Latest Publications
- Open Access
- 30 October 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (3 (143)) , 41-51
Determination of human error probability for heavy truck drivers under wartime conditions
The object of the study is the process of changing the cognitive resource of heavy truck drivers during the logistical supply of critical infrastructure facilities under wartime conditions. The problem lies in the lack of a model of changing the cognitive resource of heavy truck drivers, which would combine the psychophysiological state of the driver, the phase structure of the run route and external disturbances to predict the probability of human error in real time. An adapted six-component model of the driver’s functional states has been developed, in which, along with optimal mobilization, monotony, fatigue and drowsiness, acute stress and cognitive tunneling are taken into account. A model of the evolution of the cognitive resource with degradation and recovery flows has been constructed, as well as a procedure for calculating the error intensity as a parameter of a heterogeneous Poisson process. As a result, critical points of reduction in the reliability of the driver’s work before the occurrence of a dangerous event were obtained and preventive actions were quantitatively substantiated. A numerical example of a six-hour run showed a decrease in cognitive resource from 0.95 to 0.006 and an increase in the accumulated probability of error to 0.1839 in the final phase with a combination of fatigue and circadian drowsiness. Such results are explained by a nonlinear increase in the intensity of errors with a deficit of cognitive resource and the synergy of internal and external factors. The model of changes in the cognitive resource of heavy truck drivers can be used by dispatching services of motor transport enterprises if biometric monitoring data and current information about the route are available
- 30 October 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (3 (143)) , 41-51
Open AccessDetermination of human error probability for heavy truck drivers under wartime conditions
The object of the study is the process of changing the cognitive resource of heavy truck drivers during the logistical supply of critical infrastructure facilities under wartime conditions. The problem lies in the lack of a model of changing the cognitive resource of heavy truck drivers, which would combine the psychophysiological state of the driver, the phase structure of the run route and external disturbances to predict the probability of human error in real time. An adapted six-component model of the driver’s functional states has been developed, in which, along with optimal mobilization, monotony, fatigue and drowsiness, acute stress and cognitive tunneling are taken into account. A model of the evolution of the cognitive resource with degradation and recovery flows has been constructed, as well as a procedure for calculating the error intensity as a parameter of a heterogeneous Poisson process. As a result, critical points of reduction in the reliability of the driver’s work before the occurrence of a dangerous event were obtained and preventive actions were quantitatively substantiated. A numerical example of a six-hour run showed a decrease in cognitive resource from 0.95 to 0.006 and an increase in the accumulated probability of error to 0.1839 in the final phase with a combination of fatigue and circadian drowsiness. Such results are explained by a nonlinear increase in the intensity of errors with a deficit of cognitive resource and the synergy of internal and external factors. The model of changes in the cognitive resource of heavy truck drivers can be used by dispatching services of motor transport enterprises if biometric monitoring data and current information about the route are available
- 16 November 2024
- Published by Lutsk National Technical University in СУЧАСНІ ТЕХНОЛОГІЇ В МАШИНОБУДУВАННІ ТА ТРАНСПОРТІ
- Vol. 2 (23) , 291-296
МЕТОД ВИЗНАЧЕННЯ ЕКОЛОГІЧНИХ ПОКАЗНИКІВ АВТОМОБІЛЯ ПІД ЧАС ЙОГО ПРОЕКТУВАННЯ
Стаття присвячена важливій проблемі сучасного автомобілебудування — визначенню екологічних показників автомобіля ще на етапі його проєктування. Автори зазначають, що кількість автомобілів перевищила 1,5 мільярда і продовжує зростати. З огляду на зростаючу кількість транспортних засобів, які експлуатуються в усьому світі, їх вплив на навколишнє середовище набуває все більшого значення. Саме тому важливо розробляти ефективні методи оцінки екологічної безпеки автомобілів ще до їхньої появи на ринку. Мета роботи полягає в розробці надійного методу розрахунку екологічних показників автомобіля під час його проєктування. Оскільки на стадії проєктування автомобіля ще не існує, тому і немає об’єкта випробувань, визначення екологічних показників можливе лише за допомогою розрахункових методів. В статті запропоновано використовувати метод, що дозволяє визначити викиди шкідливих речовин на одиницю пройденого автомобілем шляху на стадії проєктування. Це дає можливість не тільки передбачити рівень забруднення, а й врахувати вплив конструктивних параметрів транспортного засобу, таких як літраж двигуна, передавальні числа трансмісії, радіус коліс тощо. Запропонований метод дозволяє визначати допустимий рівень концентрацій шкідливих компонентів на підставі встановлених стандартів до проведення повноцінних випробувань транспортного засобу, що суттєво спрощує процес оцінки. Висновки статті підкреслюють, що розроблений метод дозволяє не лише оцінити відповідність автомобіля екологічним вимогам на стадії розробки, але й сприяє подальшому покращенню екологічних показників. Такий підхід дає можливість інженерам-розробникам автомобілів приймати більш екологічно обґрунтовані рішення та забезпечувати відповідність сучасним вимогам охорони довкілля. Ключові слова: автомобіль, двигун, екологічна безпека, перевезення, викиди, концентрації, метод.
- 16 November 2024
- Published by Lutsk National Technical University in СУЧАСНІ ТЕХНОЛОГІЇ В МАШИНОБУДУВАННІ ТА ТРАНСПОРТІ
- Vol. 2 (23) , 291-296
МЕТОД ВИЗНАЧЕННЯ ЕКОЛОГІЧНИХ ПОКАЗНИКІВ АВТОМОБІЛЯ ПІД ЧАС ЙОГО ПРОЕКТУВАННЯ
Стаття присвячена важливій проблемі сучасного автомобілебудування — визначенню екологічних показників автомобіля ще на етапі його проєктування. Автори зазначають, що кількість автомобілів перевищила 1,5 мільярда і продовжує зростати. З огляду на зростаючу кількість транспортних засобів, які експлуатуються в усьому світі, їх вплив на навколишнє середовище набуває все більшого значення. Саме тому важливо розробляти ефективні методи оцінки екологічної безпеки автомобілів ще до їхньої появи на ринку. Мета роботи полягає в розробці надійного методу розрахунку екологічних показників автомобіля під час його проєктування. Оскільки на стадії проєктування автомобіля ще не існує, тому і немає об’єкта випробувань, визначення екологічних показників можливе лише за допомогою розрахункових методів. В статті запропоновано використовувати метод, що дозволяє визначити викиди шкідливих речовин на одиницю пройденого автомобілем шляху на стадії проєктування. Це дає можливість не тільки передбачити рівень забруднення, а й врахувати вплив конструктивних параметрів транспортного засобу, таких як літраж двигуна, передавальні числа трансмісії, радіус коліс тощо. Запропонований метод дозволяє визначати допустимий рівень концентрацій шкідливих компонентів на підставі встановлених стандартів до проведення повноцінних випробувань транспортного засобу, що суттєво спрощує процес оцінки. Висновки статті підкреслюють, що розроблений метод дозволяє не лише оцінити відповідність автомобіля екологічним вимогам на стадії розробки, але й сприяє подальшому покращенню екологічних показників. Такий підхід дає можливість інженерам-розробникам автомобілів приймати більш екологічно обґрунтовані рішення та забезпечувати відповідність сучасним вимогам охорони довкілля. Ключові слова: автомобіль, двигун, екологічна безпека, перевезення, викиди, концентрації, метод.
- 1 January 2024
- Published by Publishing House Helvetica (Publications) in Transactions of Kremenchuk Mykhailo Ostrohradskyi National University
- Vol. 145 (2) , 47-57
COMPARATIVE ANALYSIS OF METHODS OF RESTORATION OF MISSING VALUES OF EXTERNAL TRACK MEASUREMENTS
- 1 January 2024
- Published by Publishing House Helvetica (Publications) in Transactions of Kremenchuk Mykhailo Ostrohradskyi National University
- Vol. 145 (2) , 47-57
COMPARATIVE ANALYSIS OF METHODS OF RESTORATION OF MISSING VALUES OF EXTERNAL TRACK MEASUREMENTS
- Open Access
- 6 April 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI» Series: New solutions in modern technologies
- No. 1(15),p. 12-18
ASYMMETRIC DISTRIBUTION OF PIPE ADAPTER FOR CARS
It is shown that the responsible parts of each vehicle are tubular connecting lines, which are included into the braking, fuel and exhaust systems of cars. These pipelines have high requirements for reliability, vibration resistance, strength, corrosion resistance and durability. These parts are used as expanders and connecting elements when transitioning from a smaller pipeline diameter to a larger one. The paper presents studies of the operation of distributing the end of the pipe blank with a rigid punch. In the process of distribution, the acting tangential stresses lead to a decrease in the thickness of the edge section of the workpiece. This entails a decrease in the reliability of this area during operation and a decrease in its maintainability and corrosion resistance. Also, to ensure the tightness of pipe connections, threads are cut or these areas are welded together in the specified areas of the workpieces. Therefore, an important design feature of tubular diffusers is the same wall thickness throughout the cross-section of the semi-finished product. To solve the problem of increasing the thickness of the semi-finished product after distribution, an asymmetric tool is proposed. The task was solved in the finite-element formulation using a special complex of 3D modeling Simulia Abaqus – student edition. The pipe blank was represented as a deformable solid, while the punch was modeled as a completely rigid discrete solid. The construction method for both models is "revolution". According to finite element modeling, dispensing with a conical asymmetric tool has advantages from the point of view of increasing the thickness of the end zone of the pipe bell. The thickness of the part increases by 22.5% from a thickness of 1.77 mm for the classic version of distribution, to 1.82 mm – for distribution with an asymmetric tool. To reduce the thinning of the wall after distributing the pipe blank, it is recommended to use an asymmetric punch. To obtain a symmetrical pipe socket, it is necessary to make two dispensing transitions with a 180° rotation of the blank or punch
- 6 April 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI» Series: New solutions in modern technologies
- No. 1(15),p. 12-18
Open AccessASYMMETRIC DISTRIBUTION OF PIPE ADAPTER FOR CARS
It is shown that the responsible parts of each vehicle are tubular connecting lines, which are included into the braking, fuel and exhaust systems of cars. These pipelines have high requirements for reliability, vibration resistance, strength, corrosion resistance and durability. These parts are used as expanders and connecting elements when transitioning from a smaller pipeline diameter to a larger one. The paper presents studies of the operation of distributing the end of the pipe blank with a rigid punch. In the process of distribution, the acting tangential stresses lead to a decrease in the thickness of the edge section of the workpiece. This entails a decrease in the reliability of this area during operation and a decrease in its maintainability and corrosion resistance. Also, to ensure the tightness of pipe connections, threads are cut or these areas are welded together in the specified areas of the workpieces. Therefore, an important design feature of tubular diffusers is the same wall thickness throughout the cross-section of the semi-finished product. To solve the problem of increasing the thickness of the semi-finished product after distribution, an asymmetric tool is proposed. The task was solved in the finite-element formulation using a special complex of 3D modeling Simulia Abaqus – student edition. The pipe blank was represented as a deformable solid, while the punch was modeled as a completely rigid discrete solid. The construction method for both models is "revolution". According to finite element modeling, dispensing with a conical asymmetric tool has advantages from the point of view of increasing the thickness of the end zone of the pipe bell. The thickness of the part increases by 22.5% from a thickness of 1.77 mm for the classic version of distribution, to 1.82 mm – for distribution with an asymmetric tool. To reduce the thinning of the wall after distributing the pipe blank, it is recommended to use an asymmetric punch. To obtain a symmetrical pipe socket, it is necessary to make two dispensing transitions with a 180° rotation of the blank or punch
- 1 January 2023
- Published by Publishing House Helvetica (Publications) in Transactions of Kremenchuk Mykhailo Ostrohradskyi National University
- No. 2,p. 134-142
FUEL ECONOMY EVALUATION CRITERIA VEHICLE AS AN INDICATOR OF ITS ENERGY EFFICIENCY
- 1 January 2023
- Published by Publishing House Helvetica (Publications) in Transactions of Kremenchuk Mykhailo Ostrohradskyi National University
- No. 2,p. 134-142
FUEL ECONOMY EVALUATION CRITERIA VEHICLE AS AN INDICATOR OF ITS ENERGY EFFICIENCY
- 20 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Peculiarities of the of Engineering Disciplines Teaching Process Organization Using Three-Dimensional Computer Modeling Methods
The article examines the technology of teaching organization and methodological features of the development and implementation of educational programs in the field of information computer technologies. 3D technologies using potential investigated in order to improve the quality of professional training of students was investigated and intensification of the educational process in a higher educational institution by increasing the interest of participants in the educational process to study and more active an educational disciplines sections mastering.
- 20 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Peculiarities of the of Engineering Disciplines Teaching Process Organization Using Three-Dimensional Computer Modeling Methods
The article examines the technology of teaching organization and methodological features of the development and implementation of educational programs in the field of information computer technologies. 3D technologies using potential investigated in order to improve the quality of professional training of students was investigated and intensification of the educational process in a higher educational institution by increasing the interest of participants in the educational process to study and more active an educational disciplines sections mastering.
- 20 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Increasing the Energy Efficiency of Sheet Bending Equipment
It is shown that energy saving and energy efficiency increase should be considered as one of the main sources of future economic growth. The equipment that is used for the manufacture of products in the press shops has powerful electric motors. They are the main consumers of electrical energy. Replacing powerful electric motors with low-power ones will lead to energy savings. Crank bending machines are mainly used in mass production press shops. This calculation method makes it possible to control the deformation force and decrease it to reduce the overall operation of the press and its energy consumption. This will allow the use of less powerful presses for bending. It is shown that deformation occurs in two stages of sequential loading of the workpiece, which leads to splitting up the deformation process and, thereby, to decreasing the required force compared to the initial one. Using these analytical dependences for calculating the geometric dimensions of the resulting rift, it is possible to simplify the structure and design of the deforming tool, create a method for calculating technological and design parameters. The minimum force of the buffer, which must be used in the first operation, can be calculated based on the condition of maintaining the straightness of the workpiece and overcoming the resistance forces.
- 20 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Increasing the Energy Efficiency of Sheet Bending Equipment
It is shown that energy saving and energy efficiency increase should be considered as one of the main sources of future economic growth. The equipment that is used for the manufacture of products in the press shops has powerful electric motors. They are the main consumers of electrical energy. Replacing powerful electric motors with low-power ones will lead to energy savings. Crank bending machines are mainly used in mass production press shops. This calculation method makes it possible to control the deformation force and decrease it to reduce the overall operation of the press and its energy consumption. This will allow the use of less powerful presses for bending. It is shown that deformation occurs in two stages of sequential loading of the workpiece, which leads to splitting up the deformation process and, thereby, to decreasing the required force compared to the initial one. Using these analytical dependences for calculating the geometric dimensions of the resulting rift, it is possible to simplify the structure and design of the deforming tool, create a method for calculating technological and design parameters. The minimum force of the buffer, which must be used in the first operation, can be calculated based on the condition of maintaining the straightness of the workpiece and overcoming the resistance forces.
- 20 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
The Intellectual Organization Main Directions for the Car Wheel Rims Production within the Framework of the Industry 4.0 Program
It is shown that the car steel wheel rims production by profiling is faced with certain difficulties. These difficulties are associated with solving the profiling process fatigue problems, ensuring the quality of the finished image, eliminating shortages and increasing productivity without significant labor costs. It is possible to solve the set tasks through the autonomous intelligent production creation. The main transformation mechanics of the metal profiling line into an intelligent system was shown. Such a system will make it possible to increase the productivity by means the constituent production process dynamic monitoring and the processing technology at each profile transition control. A profiling machines transition algorithm from manual control to effective adaptive control is outlined. For this, all technology components are involved, starting from the workpiece and the design of machines and ending with profile sensors and tracking devices.
- 20 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
The Intellectual Organization Main Directions for the Car Wheel Rims Production within the Framework of the Industry 4.0 Program
It is shown that the car steel wheel rims production by profiling is faced with certain difficulties. These difficulties are associated with solving the profiling process fatigue problems, ensuring the quality of the finished image, eliminating shortages and increasing productivity without significant labor costs. It is possible to solve the set tasks through the autonomous intelligent production creation. The main transformation mechanics of the metal profiling line into an intelligent system was shown. Such a system will make it possible to increase the productivity by means the constituent production process dynamic monitoring and the processing technology at each profile transition control. A profiling machines transition algorithm from manual control to effective adaptive control is outlined. For this, all technology components are involved, starting from the workpiece and the design of machines and ending with profile sensors and tracking devices.
- 26 May 2021
- Published by Springer Nature
- p. 104-113
The Optimal Conditions for Adding Strain to the Deformation Zone During the Expansion of Automobile Pipe Adapters
- 26 May 2021
- Published by Springer Nature
- p. 104-113
The Optimal Conditions for Adding Strain to the Deformation Zone During the Expansion of Automobile Pipe Adapters
- 14 April 2021
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 316, 873-879
Analysis of Galvanized Steel Sheets Fabrication in Cold Rolling Shop and Identification of Local Impacts Contributing to Corrosion of Metal-Products
An urgent need has been identified, associated with the validity of improving the process for the manufacturing of galvanized steel, in the analysis and improvement of each stage of production in the conditions of the particular cold-rolled shop of the Iron and Steel Work. As a novelty, the processes and equipment for cleaning a hot-rolled strip, pickling a strip, rolling of pickled strips, physicochemical surface treatment, zinc coating, passivation, and other elements were reviewed from the point of view of possible corrosion consequences of the production. For the first time in the considered production system, elements and operations, their errors and imperfections, which can lead to poor-quality coating, violation of the zinc layer and reasons that contribute to the corrosion of galvanized metal products in the future, were identified at each stage.
- 14 April 2021
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 316, 873-879
Analysis of Galvanized Steel Sheets Fabrication in Cold Rolling Shop and Identification of Local Impacts Contributing to Corrosion of Metal-Products
An urgent need has been identified, associated with the validity of improving the process for the manufacturing of galvanized steel, in the analysis and improvement of each stage of production in the conditions of the particular cold-rolled shop of the Iron and Steel Work. As a novelty, the processes and equipment for cleaning a hot-rolled strip, pickling a strip, rolling of pickled strips, physicochemical surface treatment, zinc coating, passivation, and other elements were reviewed from the point of view of possible corrosion consequences of the production. For the first time in the considered production system, elements and operations, their errors and imperfections, which can lead to poor-quality coating, violation of the zinc layer and reasons that contribute to the corrosion of galvanized metal products in the future, were identified at each stage.