Gema Pliego
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gema Pliego has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Juan Antonio Zazo
Chemical Engineering Department, Universidad Autonoma de Madrid, Ctra. Colmenar km. 15, 28049 Madrid, Spain
9 shared publications - Jose Antonio Casas
Departamento de Ingeniería Química, Universidad Autónoma de Madrid, Ctra. Colmenar km 15 (28049), Madrid, Spain
8 shared publications - Juan Jose Rodriguez
Chemical Engineering Department, Universidad Autónoma de Madrid, 28049 Madrid, Spain
7 shared publications - Patricia García-Muñoz
Universidad Politécnica de Madrid (UPM), E.T.S de Ingenieros Industriales, Departamento de Ingeniería Química Industrial y del Medio Ambiente, c/José Gutiérrez Abascal 2, 28006, Madrid, Spain
5 shared publications - Xiyan Xu
School of Chemistry and Chemical Engineering, Beijing Institute of Technology, 5 South Street of Zhongguancun, 100081, Beijing, China
2 shared publications - Alice Luminita Petre
Institute of Physical Chemistry of the Romanian Academy
1 shared publication
Latest Publications
- Open Access
Solar Photo-Fenton: An Effective Method for MCPA Degradation
The extensive use of herbicide 2-methyl-4-chlorophenoxyacetic acid (MCPA), coupled with its limited biodegradability, has led to its ubiquitous presence in aquatic environments. This work investigates the removal of MCPA (100 mg/L) in the aqueous phase via solar photo-Fenton. The process was carried out in a 700 mL reactor using a Xe lamp that simulates solar radiation (λ: 250–700 nm). A parametric study was conducted to assess the influence of dissolved O2 on the reaction medium, Fe2+ dosage, H2O2 concentration and pH0. The results indicate that dissolved O2 boosts pollutant mineralization, even working at sub-stoichiometric H2O2 concentrations. Under optimal reaction conditions ([Fe2+]: 7.5 mg/L, [H2O2]0: 322 mg/L (stoichiometric dose), pH0: 3.5), the MCPA reached almost complete mineralization (XTOC: 98.40%) in 180 min. Phytotoxicity and ecotoxicity assessments of treated effluents revealed that even working at sub-stoichiometric H2O2 dosages, toxicity decreases with the solar photo-Fenton treatment. Finally, the solar photo-Fenton process was evaluated in relevant matrices (river water and WWTP secondary effluent) and a realistic pollutant concentration (100 µg/L). In all cases, the pollutant degradation was ≥70% in 60 min, demonstrating the potential of this technology as a tertiary treatment.
Open AccessSolar Photo-Fenton: An Effective Method for MCPA Degradation
The extensive use of herbicide 2-methyl-4-chlorophenoxyacetic acid (MCPA), coupled with its limited biodegradability, has led to its ubiquitous presence in aquatic environments. This work investigates the removal of MCPA (100 mg/L) in the aqueous phase via solar photo-Fenton. The process was carried out in a 700 mL reactor using a Xe lamp that simulates solar radiation (λ: 250–700 nm). A parametric study was conducted to assess the influence of dissolved O2 on the reaction medium, Fe2+ dosage, H2O2 concentration and pH0. The results indicate that dissolved O2 boosts pollutant mineralization, even working at sub-stoichiometric H2O2 concentrations. Under optimal reaction conditions ([Fe2+]: 7.5 mg/L, [H2O2]0: 322 mg/L (stoichiometric dose), pH0: 3.5), the MCPA reached almost complete mineralization (XTOC: 98.40%) in 180 min. Phytotoxicity and ecotoxicity assessments of treated effluents revealed that even working at sub-stoichiometric H2O2 dosages, toxicity decreases with the solar photo-Fenton treatment. Finally, the solar photo-Fenton process was evaluated in relevant matrices (river water and WWTP secondary effluent) and a realistic pollutant concentration (100 µg/L). In all cases, the pollutant degradation was ≥70% in 60 min, demonstrating the potential of this technology as a tertiary treatment.
- 1 September 2020
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 273
Selective reduction of nitrate to N2 using ilmenite as a low cost photo-catalyst
- 1 September 2020
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 273
Selective reduction of nitrate to N2 using ilmenite as a low cost photo-catalyst
- 1 August 2019
- Published by Elsevier in Chemical Engineering Journal
- Vol. 370, 695-705
Reaction pathways of heat-activated persulfate oxidation of naphthenic acids in the presence and absence of dissolved oxygen in water
- 1 August 2019
- Published by Elsevier in Chemical Engineering Journal
- Vol. 370, 695-705
Reaction pathways of heat-activated persulfate oxidation of naphthenic acids in the presence and absence of dissolved oxygen in water
- 1 December 2018
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 6 (6) , 7312-7317
Photocatalytic wet peroxide oxidation process at circumneutral pH using ilmenite as catalyst
- 1 December 2018
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 6 (6) , 7312-7317
Photocatalytic wet peroxide oxidation process at circumneutral pH using ilmenite as catalyst
- 7 July 2017
- Published by Taylor & Francis in Critical Reviews in Environmental Science and Technology
- Vol. 47 (15) , 1337-1370
An overview on the application of advanced oxidation processes for the removal of naphthenic acids from water
Although the exploitation of new energy sources like oil sand or shale may efficiently relieve the urgency of energy shortage, it can also have significant and adverse environmental impacts since huge volumes of oil-containing wastewaters are produced yearly worldwide due to such activities. Naphthenic acids (NAs), which are reported to be bio-recalcitrant due to their structural complexity and toxicity, are the main harmful components of oil shale fracking processes and oil sand process-affected waters. Identification techniques are being continuously improved to deal with the growing analytical need for traditional NAs and emerging ones like oxy-, aromatic, and diamondoid NAs. Meanwhile, treatment approaches focused on technical solutions have been investigated in the past decades. Among these, advanced oxidation processes are the most studied. Different oxidizing agents, like ozone, hydrogen peroxide, and persulfate, among others, have been used, giving rise to a diversity of techniques. The current work presents an updated overview of these techniques with regard to their application for the removal of NAs from water.
- 7 July 2017
- Published by Taylor & Francis in Critical Reviews in Environmental Science and Technology
- Vol. 47 (15) , 1337-1370
An overview on the application of advanced oxidation processes for the removal of naphthenic acids from water
Although the exploitation of new energy sources like oil sand or shale may efficiently relieve the urgency of energy shortage, it can also have significant and adverse environmental impacts since huge volumes of oil-containing wastewaters are produced yearly worldwide due to such activities. Naphthenic acids (NAs), which are reported to be bio-recalcitrant due to their structural complexity and toxicity, are the main harmful components of oil shale fracking processes and oil sand process-affected waters. Identification techniques are being continuously improved to deal with the growing analytical need for traditional NAs and emerging ones like oxy-, aromatic, and diamondoid NAs. Meanwhile, treatment approaches focused on technical solutions have been investigated in the past decades. Among these, advanced oxidation processes are the most studied. Different oxidizing agents, like ozone, hydrogen peroxide, and persulfate, among others, have been used, giving rise to a diversity of techniques. The current work presents an updated overview of these techniques with regard to their application for the removal of NAs from water.
- 10 September 2016
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 23 (23) , 23449-23455
Improving the Fenton process by visible LED irradiation
The effect of irradiation with visible light-emitting diode (LED) light on the efficiency of Fenton oxidation is investigated using phenol as the target compound (100 mg/L). The H2O2 dose and temperature are tested as operating variables with the aim of minimizing consumption of the reagents. At 50 °C, 10 mg/L Fe2+, and 60 % of the stoichiometric H2O2 amount, phenol was completely oxidized into CO2, H2O, and short chain organic acids, with oxalic acid completely degraded. Up to 95 % mineralization was achieved. This high efficiency can be attributed to the effect of LED radiation on the quinones/Fe2+/Fe3+/H2O2 cycle, which significantly increases the reaction rate, as well as on the photodecomposition of the iron complexes formed along the oxidation process, which also enhanced mineralization.
- 10 September 2016
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 23 (23) , 23449-23455
Improving the Fenton process by visible LED irradiation
The effect of irradiation with visible light-emitting diode (LED) light on the efficiency of Fenton oxidation is investigated using phenol as the target compound (100 mg/L). The H2O2 dose and temperature are tested as operating variables with the aim of minimizing consumption of the reagents. At 50 °C, 10 mg/L Fe2+, and 60 % of the stoichiometric H2O2 amount, phenol was completely oxidized into CO2, H2O, and short chain organic acids, with oxalic acid completely degraded. Up to 95 % mineralization was achieved. This high efficiency can be attributed to the effect of LED radiation on the quinones/Fe2+/Fe3+/H2O2 cycle, which significantly increases the reaction rate, as well as on the photodecomposition of the iron complexes formed along the oxidation process, which also enhanced mineralization.
- 2 April 2015
- Published by Taylor & Francis in Critical Reviews in Environmental Science and Technology
- Vol. 45 (24) , 2611-2692
Trends in the Intensification of the Fenton Process for Wastewater Treatment: An Overview
The implementation of increasingly stringent regulations for wastewater discharge has enforced research efforts toward either the implementation of novel treatments or the improvement of those presently available. The literature on the use of Fenton oxidation in wastewater treatment has established this method as one of the most effective and suitable process for the abatement of recalcitrant water pollutants. However, despite the many advantages of the conventional Fenton process, there are issues relative to pH modulation, the cost associated to H2O2 and catalyst consumption as well as to sludge disposal that limit a more extended full-scale application. In recent years, several solutions have been developed for the sake of improving Fenton (or Fenton-like) oxidation as a cost-effective technology. This paper presents a thorough review on the different ways of intensifying the Fenton by using radiation, electrochemistry, and/or heterogeneous catalysts, as well as by optimizing the main operating conditions in the conventional homogeneous system. The application of these enhanced technologies to synthetic and real industrial wastewaters is described and discussed.
- 2 April 2015
- Published by Taylor & Francis in Critical Reviews in Environmental Science and Technology
- Vol. 45 (24) , 2611-2692
Trends in the Intensification of the Fenton Process for Wastewater Treatment: An Overview
The implementation of increasingly stringent regulations for wastewater discharge has enforced research efforts toward either the implementation of novel treatments or the improvement of those presently available. The literature on the use of Fenton oxidation in wastewater treatment has established this method as one of the most effective and suitable process for the abatement of recalcitrant water pollutants. However, despite the many advantages of the conventional Fenton process, there are issues relative to pH modulation, the cost associated to H2O2 and catalyst consumption as well as to sludge disposal that limit a more extended full-scale application. In recent years, several solutions have been developed for the sake of improving Fenton (or Fenton-like) oxidation as a cost-effective technology. This paper presents a thorough review on the different ways of intensifying the Fenton by using radiation, electrochemistry, and/or heterogeneous catalysts, as well as by optimizing the main operating conditions in the conventional homogeneous system. The application of these enhanced technologies to synthetic and real industrial wastewaters is described and discussed.
- 12 May 2014
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 89 (6) , 814-818
Complete degradation of the persistent anti‐depressant sertraline in aqueous solution by solar photo‐Fenton oxidation
BACKGROUND: Selective serotonin reuptake inhibitor sertraline is found to be one of the most persistent pharmaceutical drugs and it has been detected in effluents from wastewater treatment plants. This work evaluates the feasibility of homogeneous solar photo‐Fenton oxidation for treating aqueous solutions containing sertraline.RESULTS: The influence of iron and H2O2 dosages was studied in order to optimize the reagents consumption. The beneficial role of simulated solar irradiation was noticeable and sertraline was readily oxidized; TOC removal up to 90% was achieved at a hydrogen peroxide dose as low as 40% of the stoichiometric amount for mineralization. Dechlorination was the first step of the proposed reaction pathway giving rise to the formation of by‐products of much lower toxicity.CONCLUSIONS: Solar simulated photo‐Fenton allowed reduction of the doses of iron and H2O2 needed, and therefore the main operating cost associated with this process, without compromising the quality of the effluent in terms of ecotoxicity. © 2014 Society of Chemical Industry.
- 12 May 2014
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 89 (6) , 814-818
Complete degradation of the persistent anti‐depressant sertraline in aqueous solution by solar photo‐Fenton oxidation
BACKGROUND: Selective serotonin reuptake inhibitor sertraline is found to be one of the most persistent pharmaceutical drugs and it has been detected in effluents from wastewater treatment plants. This work evaluates the feasibility of homogeneous solar photo‐Fenton oxidation for treating aqueous solutions containing sertraline.RESULTS: The influence of iron and H2O2 dosages was studied in order to optimize the reagents consumption. The beneficial role of simulated solar irradiation was noticeable and sertraline was readily oxidized; TOC removal up to 90% was achieved at a hydrogen peroxide dose as low as 40% of the stoichiometric amount for mineralization. Dechlorination was the first step of the proposed reaction pathway giving rise to the formation of by‐products of much lower toxicity.CONCLUSIONS: Solar simulated photo‐Fenton allowed reduction of the doses of iron and H2O2 needed, and therefore the main operating cost associated with this process, without compromising the quality of the effluent in terms of ecotoxicity. © 2014 Society of Chemical Industry.
- 26 April 2014
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 21 (21) , 12129-12134
Treatment of a wastewater from a pesticide manufacture by combined coagulation and Fenton oxidation
The treatment of a non-biodegradable agrochemical wastewater has been studied by coupling of preliminary coagulation—flocculation step and further Fenton oxidation. High percentages of chemical oxygen demand (COD) removal (up to 58 %) were achieved in a first step using polyferric chloride as coagulant. This reduced significantly the amount of H2O2 required in the further Fenton oxidation. Using the stoichiometric amount relative to COD around 80 % of the remaining organic load was mineralized. The combined treatment allowed achieving the regional discharge limits of ecotoxicity at a cost substantially lower than the solution used so far where these wastewaters are managed as hazardous wastes.
- 26 April 2014
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 21 (21) , 12129-12134
Treatment of a wastewater from a pesticide manufacture by combined coagulation and Fenton oxidation
The treatment of a non-biodegradable agrochemical wastewater has been studied by coupling of preliminary coagulation—flocculation step and further Fenton oxidation. High percentages of chemical oxygen demand (COD) removal (up to 58 %) were achieved in a first step using polyferric chloride as coagulant. This reduced significantly the amount of H2O2 required in the further Fenton oxidation. Using the stoichiometric amount relative to COD around 80 % of the remaining organic load was mineralized. The combined treatment allowed achieving the regional discharge limits of ecotoxicity at a cost substantially lower than the solution used so far where these wastewaters are managed as hazardous wastes.
- 1 May 2013
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 252-253, 180-185
Case study of the application of Fenton process to highly polluted wastewater from power plant
- 1 May 2013
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 252-253, 180-185
Case study of the application of Fenton process to highly polluted wastewater from power plant