Jie Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jie Li has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Jonghyun Park
Department of Mechanical and Aerospace Engineering, Missouri University of Science and Technology, Rolla, MO, USA
7 shared publicationsJ. Park
4 shared publicationsN. Lotfi
4 shared publicationsR. G. Landers
3 shared publicationsRahul Panat
Carnegie Mellon University
3 shared publications- Jonghyun Park
Department of Mechanical and Aerospace Engineering, Missouri University of Science and Technology, Rolla, Missouri 65401, USA
2 shared publications
Latest Publications
- Open Access
- 21 December 2018
- Published by AccScience Publishing in International Journal of Bioprinting
- Vol. 5 (1) , 163
Near-field electrospinning of a polymer/bioactive glass composite to fabricate 3D biomimetic structures
Bioactive glasses have recently gained attention in tissue engineering and three-dimensional (3D) bioprinting because of their ability to enhance angiogenesis. Some challenges for developing biological tissues with bioactive glasses include incorporation of glass particles and achieving a 3D architecture mimicking natural tissues. In this study, we investigate the fabrication of scaffolds with a polymer/bioactive glass composite using near-field electrospinning (NFES). An overall controlled 3D scaffold with pores, containing random fibers, is created and aimed to provide superior cell proliferation. Highly angiogenic borate bioactive glass (13-93B3) in 20 wt.% is added to polycaprolactone (PCL) to fabricate scaffolds using the NFES technique. Scaffolds measuring 5 mm × 5 mm × 0.2 mm3 in overall dimensions were seeded with human adipose-derived mesenchymal stem cells to investigate the cell viability. The cell viability on PCL and PCL+glass scaffolds fabricated using NFES technique and 3D printing is compared and discussed. The results indicated higher cell proliferation on 3D biomimetic scaffolds fabricated by NFES technique.
- 21 December 2018
- Published by AccScience Publishing in International Journal of Bioprinting
- Vol. 5 (1) , 163
Open AccessNear-field electrospinning of a polymer/bioactive glass composite to fabricate 3D biomimetic structures
Bioactive glasses have recently gained attention in tissue engineering and three-dimensional (3D) bioprinting because of their ability to enhance angiogenesis. Some challenges for developing biological tissues with bioactive glasses include incorporation of glass particles and achieving a 3D architecture mimicking natural tissues. In this study, we investigate the fabrication of scaffolds with a polymer/bioactive glass composite using near-field electrospinning (NFES). An overall controlled 3D scaffold with pores, containing random fibers, is created and aimed to provide superior cell proliferation. Highly angiogenic borate bioactive glass (13-93B3) in 20 wt.% is added to polycaprolactone (PCL) to fabricate scaffolds using the NFES technique. Scaffolds measuring 5 mm × 5 mm × 0.2 mm3 in overall dimensions were seeded with human adipose-derived mesenchymal stem cells to investigate the cell viability. The cell viability on PCL and PCL+glass scaffolds fabricated using NFES technique and 3D printing is compared and discussed. The results indicated higher cell proliferation on 3D biomimetic scaffolds fabricated by NFES technique.
- 17 November 2018
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 165 (14) , A3566-A3573
Enhanced Battery Performance through Three-Dimensional Structured Electrodes: Experimental and Modeling Study
Three-dimensional (3D) electrode structures have the potential to significantly improve Li-ion battery performance, including power and energy density. Due to the complexity of geometries caused by scale expansion, however, a more precise understanding of the relationship between battery physics and structures is required. In this work, a novel hybrid 3D structure is investigated to thoroughly understand the advantages of 3D structured electrodes and to provide a guideline for design optimization. Experimental observation from an extrusion-based 3D structure is incorporated into a 3D electrochemical model, based on porous theory, with a 4th order approximation for solid phase concentration. This systematic study has been focused on the impact of electrode tap density (thickness and volume fractions) on 3D battery performance. Experimental and simulation results showed that the proposed 3D hybrid structure exhibited higher specific capacity and areal capacity than conventional electrode structures. This was found to be due to the short diffusion path and uniformly distributed concentration within the electrodes, even with thicker electrodes. Parametric metrics were introduced to provide a physical insight into the 3D hybrid structure, to identify the factors limiting battery responses, and to, eventually, provide a guideline for design optimization with more general 3D geometries.
- 17 November 2018
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 165 (14) , A3566-A3573
Enhanced Battery Performance through Three-Dimensional Structured Electrodes: Experimental and Modeling Study
Three-dimensional (3D) electrode structures have the potential to significantly improve Li-ion battery performance, including power and energy density. Due to the complexity of geometries caused by scale expansion, however, a more precise understanding of the relationship between battery physics and structures is required. In this work, a novel hybrid 3D structure is investigated to thoroughly understand the advantages of 3D structured electrodes and to provide a guideline for design optimization. Experimental observation from an extrusion-based 3D structure is incorporated into a 3D electrochemical model, based on porous theory, with a 4th order approximation for solid phase concentration. This systematic study has been focused on the impact of electrode tap density (thickness and volume fractions) on 3D battery performance. Experimental and simulation results showed that the proposed 3D hybrid structure exhibited higher specific capacity and areal capacity than conventional electrode structures. This was found to be due to the short diffusion path and uniformly distributed concentration within the electrodes, even with thicker electrodes. Parametric metrics were introduced to provide a physical insight into the 3D hybrid structure, to identify the factors limiting battery responses, and to, eventually, provide a guideline for design optimization with more general 3D geometries.
- 1 October 2018
- Published by Elsevier in Additive Manufacturing
- Vol. 23, 70-78
3D printed hierarchically-porous microlattice electrode materials for exceptionally high specific capacity and areal capacity lithium ion batteries
- 1 October 2018
- Published by Elsevier in Additive Manufacturing
- Vol. 23, 70-78
3D printed hierarchically-porous microlattice electrode materials for exceptionally high specific capacity and areal capacity lithium ion batteries
- 19 June 2018
- Published by The Electrochemical Society in ECS Transactions
- Vol. 85 (13) , 369-378
Microstructure-Controlled 3D Electrodes for Lithium-Ion Batteries
A new battery electrode fabrication process in which the micro/macroscale structures are simultaneously controlled is proposed. In the processing, an electric field controls the microscale particle network in an electrode, while an additive manufacturing controls the macroscale three-dimensional geometry of the electrode. This synergistic control of micro-/macro-structures is a novel concept in energy material processing, and has considerable potential for providing unprecedented control of electrode structures with enhancing performance. Electrochemical tests have shown that these new electrodes exhibit superior performance in their specific capacity, areal capacity, and life cycle.
- 19 June 2018
- Published by The Electrochemical Society in ECS Transactions
- Vol. 85 (13) , 369-378
Microstructure-Controlled 3D Electrodes for Lithium-Ion Batteries
A new battery electrode fabrication process in which the micro/macroscale structures are simultaneously controlled is proposed. In the processing, an electric field controls the microscale particle network in an electrode, while an additive manufacturing controls the macroscale three-dimensional geometry of the electrode. This synergistic control of micro-/macro-structures is a novel concept in energy material processing, and has considerable potential for providing unprecedented control of electrode structures with enhancing performance. Electrochemical tests have shown that these new electrodes exhibit superior performance in their specific capacity, areal capacity, and life cycle.
- Top Cited Papers
- 1 February 2018
- Published by Elsevier in Applied Energy
- Vol. 212, 1178-1190
A single particle model with chemical/mechanical degradation physics for lithium ion battery State of Health (SOH) estimation
- 1 February 2018
- Published by Elsevier in Applied Energy
- Vol. 212, 1178-1190
Top Cited PapersA single particle model with chemical/mechanical degradation physics for lithium ion battery State of Health (SOH) estimation
- Open Access
- 30 January 2018
- Published by Springer Nature in Scientific Reports
- Vol. 8 (1) , 1846
Macro-/Micro-Controlled 3D Lithium-Ion Batteries via Additive Manufacturing and Electric Field Processing
This paper presents a new concept for making battery electrodes that can simultaneously control macro-/micro-structures and help address current energy storage technology gaps and future energy storage requirements. Modern batteries are fabricated in the form of laminated structures that are composed of randomly mixed constituent materials. This randomness in conventional methods can provide a possibility of developing new breakthrough processing techniques to build well-organized structures that can improve battery performance. In the proposed processing, an electric field (EF) controls the microstructures of manganese-based electrodes, while additive manufacturing controls macro-3D structures and the integration of both scales. The synergistic control of micro-/macro-structures is a novel concept in energy material processing that has considerable potential for providing unprecedented control of electrode structures, thereby enhancing performance. Electrochemical tests have shown that these new electrodes exhibit superior performance in their specific capacity, areal capacity, and life cycle.
- 30 January 2018
- Published by Springer Nature in Scientific Reports
- Vol. 8 (1) , 1846
Open AccessMacro-/Micro-Controlled 3D Lithium-Ion Batteries via Additive Manufacturing and Electric Field Processing
This paper presents a new concept for making battery electrodes that can simultaneously control macro-/micro-structures and help address current energy storage technology gaps and future energy storage requirements. Modern batteries are fabricated in the form of laminated structures that are composed of randomly mixed constituent materials. This randomness in conventional methods can provide a possibility of developing new breakthrough processing techniques to build well-organized structures that can improve battery performance. In the proposed processing, an electric field (EF) controls the microstructures of manganese-based electrodes, while additive manufacturing controls macro-3D structures and the integration of both scales. The synergistic control of micro-/macro-structures is a novel concept in energy material processing that has considerable potential for providing unprecedented control of electrode structures, thereby enhancing performance. Electrochemical tests have shown that these new electrodes exhibit superior performance in their specific capacity, areal capacity, and life cycle.
- 7 July 2017
- Published by The Electrochemical Society in ECS Transactions
- Vol. 77 (11) , 1003-1014
A Single Particle-Based Battery Degradation Model Including Chemical and Mechanical Degradation Physics
Accurate and rapid prediction of the status of a lithium-ion battery is an important process in Battery Management System (BMS). In this work, a single particle model is developed by focusing on crack propagation coupled with Solid Electrolyte Interface (SEI) layer formation and its evolution. The lithium ion loss due to the SEI layer evolution is integrated with our previously developed advanced single particle model that includes electrolytic physics. This model is fairly well predictive of capacity fade and voltage change as a function of cycle number and temperature. Despite its implementation in a single particle model, the results provide quantitative information on the role of SEI layer growth and crack propagation, and corresponding capacity fade and power loss.
- 7 July 2017
- Published by The Electrochemical Society in ECS Transactions
- Vol. 77 (11) , 1003-1014
A Single Particle-Based Battery Degradation Model Including Chemical and Mechanical Degradation Physics
Accurate and rapid prediction of the status of a lithium-ion battery is an important process in Battery Management System (BMS). In this work, a single particle model is developed by focusing on crack propagation coupled with Solid Electrolyte Interface (SEI) layer formation and its evolution. The lithium ion loss due to the SEI layer evolution is integrated with our previously developed advanced single particle model that includes electrolytic physics. This model is fairly well predictive of capacity fade and voltage change as a function of cycle number and temperature. Despite its implementation in a single particle model, the results provide quantitative information on the role of SEI layer growth and crack propagation, and corresponding capacity fade and power loss.
- 7 July 2017
- Published by The Electrochemical Society in ECS Transactions
- Vol. 77 (11) , 1209-1218
3D Printed Hybrid Electrodes for Lithium-Ion Batteries
A novel hybrid 3D structured electrode, with a high-aspect ratio, is fabricated via extrusion-based additive manufacturing to achieve high mass loading and combine the advantages offered by a conventional laminated structure and a 3D digital structure. This structure is designed to enhance interfacial reactions and species transport by utilizing the 3D structure. Two key challenges in 3D structured electrodes are addressed, including solution preparation and scale-up. The paste is optimized with a high viscosity to avoid the typical complexity encountered in preparing a solution for 3D printing, and the proposed hybrid 3D structures can be easily added to the conventional laminated structures. This is demonstrated by using a CR2032 coin cell, which also solves the typical assembly problems that occur with 3D structured electrodes. This innovative design and fabrication process demonstrates high areal energy and power density, which are critical requirements for energy storage systems in transportation and stationary applications.
- 7 July 2017
- Published by The Electrochemical Society in ECS Transactions
- Vol. 77 (11) , 1209-1218
3D Printed Hybrid Electrodes for Lithium-Ion Batteries
A novel hybrid 3D structured electrode, with a high-aspect ratio, is fabricated via extrusion-based additive manufacturing to achieve high mass loading and combine the advantages offered by a conventional laminated structure and a 3D digital structure. This structure is designed to enhance interfacial reactions and species transport by utilizing the 3D structure. Two key challenges in 3D structured electrodes are addressed, including solution preparation and scale-up. The paste is optimized with a high viscosity to avoid the typical complexity encountered in preparing a solution for 3D printing, and the proposed hybrid 3D structures can be easily added to the conventional laminated structures. This is demonstrated by using a CR2032 coin cell, which also solves the typical assembly problems that occur with 3D structured electrodes. This innovative design and fabrication process demonstrates high areal energy and power density, which are critical requirements for energy storage systems in transportation and stationary applications.
- 1 April 2017
- Published by Elsevier in Materials & Design
- Vol. 119, 417-424
A hybrid three-dimensionally structured electrode for lithium-ion batteries via 3D printing
- 1 April 2017
- Published by Elsevier in Materials & Design
- Vol. 119, 417-424
A hybrid three-dimensionally structured electrode for lithium-ion batteries via 3D printing