Kapil Bhatt
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Kapil Bhatt has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
Sandeep Kumar
National Centre for Flexible Electronics, IIT, Kanpur, India
7 shared publications- Sandeep Kumar
RF & Flexible Microelectronics Research Laboratory, Department of ECE, University Institute of Engineering and Technology, Kurukshetra University, Kurukshetra, India
7 shared publications C.C. Tripathi
5 shared publications- Pramod Kumar
Indian Institute of Technology Roorkee, Roorkee, Roorkee, 247667, INDIA
4 shared publications Sandeep
Department of Electronics and Communication Engineering, University Institute of Engineering and Technology, Kurukshetra University, Kurukshetra, India
4 shared publicationsShilpi
Department of Electronics and Communication Engineering, University Institute of Engineering and Technology, Kurukshetra University, Kurukshetra, India
4 shared publications
Latest Publications
- 9 June 2020
- Published by Springer Nature in Applied Physics A
- Vol. 126 (7) , 1-11
Highly sensitive and reusable Cu+2/polyaniline/reduced graphene oxide nanocomposite ink-based non-enzymatic glucose sensor
- 9 June 2020
- Published by Springer Nature in Applied Physics A
- Vol. 126 (7) , 1-11
Highly sensitive and reusable Cu+2/polyaniline/reduced graphene oxide nanocomposite ink-based non-enzymatic glucose sensor
- 1 June 2020
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 20 (6) , 3780-3784
Metal Insulator Metal Diode: A Potential Candidate for Energy Harvesting Applications
Metal-Insulator-Metal (MIM) diodes used for infrared detection and frequency mixing since many decades and their development for energy harvesting applications in rectenna solar cell has accelerated a decade ago. In the horizon of these applications less complex fabrication methodology, accurate simulation methods and optimum material combination are required. Ultra-fast response of MIM diodes makes them a potential candidate for solar energy harvesting applications. Here in this work, the design and fabrication issues of MIM diode from simulation methodology based on insulating thickness properties to the fabrication methodology are discussed. MIM diode for Al–Al2O3–Ag combination is fabricated and characteristics such as I(V), asymmetry and non-linearity are reported.
- 1 June 2020
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 20 (6) , 3780-3784
Metal Insulator Metal Diode: A Potential Candidate for Energy Harvesting Applications
Metal-Insulator-Metal (MIM) diodes used for infrared detection and frequency mixing since many decades and their development for energy harvesting applications in rectenna solar cell has accelerated a decade ago. In the horizon of these applications less complex fabrication methodology, accurate simulation methods and optimum material combination are required. Ultra-fast response of MIM diodes makes them a potential candidate for solar energy harvesting applications. Here in this work, the design and fabrication issues of MIM diode from simulation methodology based on insulating thickness properties to the fabrication methodology are discussed. MIM diode for Al–Al2O3–Ag combination is fabricated and characteristics such as I(V), asymmetry and non-linearity are reported.
- 20 January 2020
- Published by Springer Nature in Pramana
- Vol. 94 (1) , 31
High-performance ultra-low leakage current graphene-based screen-printed field-effect transistor on paper substrate
- 20 January 2020
- Published by Springer Nature in Pramana
- Vol. 94 (1) , 31
High-performance ultra-low leakage current graphene-based screen-printed field-effect transistor on paper substrate
- 17 December 2019
- Published by Wiley in Advanced Engineering Materials
- Vol. 22 (4)
Impact of Triple Roll Milling Processing Parameters on Fluidic/Rheological and Electrical Properties of Aqueous Graphene Ink
Graphene ink is a potential candidate for the printing of electronic devices. Rheological studies of graphene inks are necessary to estimate and tune the behavior of ink during and after printing. Ink constituents and their fundamental properties play an important role in modifying the rheological behavior of ink. During the processing of ink, modification of these properties takes place. So, it is quite important to investigate the role of processing equipment on the ink constituents and correspondingly on the rheological behavior of ink and printed functional devices. Herein, graphene ink formulation through a triple roll mill (TRM) is presented. The particle size of graphene ink reduces substantially with both the speed of rollers and number of passes. Approximately 52% reduction in particle size is observed after five passes at the highest roller speed, and it further reduces up to 72% with an increase in the number of passes. Correspondingly, solvent loss, density, and viscosity of the inks are observed in respect of roller speed and number of passes. The impact of TRM parameters on ink constituents, rheology, and electrical properties of screen‐printed resistors is discussed and explained in terms of simple analytical models.
- 17 December 2019
- Published by Wiley in Advanced Engineering Materials
- Vol. 22 (4)
Impact of Triple Roll Milling Processing Parameters on Fluidic/Rheological and Electrical Properties of Aqueous Graphene Ink
Graphene ink is a potential candidate for the printing of electronic devices. Rheological studies of graphene inks are necessary to estimate and tune the behavior of ink during and after printing. Ink constituents and their fundamental properties play an important role in modifying the rheological behavior of ink. During the processing of ink, modification of these properties takes place. So, it is quite important to investigate the role of processing equipment on the ink constituents and correspondingly on the rheological behavior of ink and printed functional devices. Herein, graphene ink formulation through a triple roll mill (TRM) is presented. The particle size of graphene ink reduces substantially with both the speed of rollers and number of passes. Approximately 52% reduction in particle size is observed after five passes at the highest roller speed, and it further reduces up to 72% with an increase in the number of passes. Correspondingly, solvent loss, density, and viscosity of the inks are observed in respect of roller speed and number of passes. The impact of TRM parameters on ink constituents, rheology, and electrical properties of screen‐printed resistors is discussed and explained in terms of simple analytical models.
- 1 November 2019
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 111
Highly sensitive Al/Al2O3/Ag MIM diode for energy harvesting applications
- 1 November 2019
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 111
Highly sensitive Al/Al2O3/Ag MIM diode for energy harvesting applications
- 11 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 18 (12) , 2637-2641
Highly Efficient 2.4 and 5.8 GHz Dual-Band Rectenna for Energy Harvesting Applications
- 11 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 18 (12) , 2637-2641
Highly Efficient 2.4 and 5.8 GHz Dual-Band Rectenna for Energy Harvesting Applications
- Open Access
- 12 March 2019
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 9 (15) , 8262-8270
Laser patterned, high-power graphene paper resistor with dual temperature coefficient of resistance
Printing of electronic devices on a paper substrate using 2D graphene-based ink is an opening gate to innovative applications, where devices would be biodegradable, eco-friendly and can be disposed of with negligible impact on the environment. A resistor is a key element of electronic devices and their application area depends upon its power rating and temperature coefficient of resistance (TCR). In this work, in house developed graphene ink is successfully utilized to fabricate a paper-based resistor using a bar coating technique. Dimensional patterning with precise known values of resistance is achieved using a laser with freedom of shape and size which has been explored for the first time on a paper substrate. The resistor has potential to handle ∼7 W power at room temperature with capacity to withstand up to 200 V which is the highest among reported printed resistors. A dual, low and high TCR is observed, correspondingly in cold (173 K to 300 K) and hot (300 K to 373 K) temperature regions with an activation energy Ea of ∼8 meV for the cold region which is 375 percent lower than the hot region (∼30 meV). The dual TCR behaviour is of great importance for application as a stable resistor up to room temperature, and as a thermistor above room temperature.
- 12 March 2019
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 9 (15) , 8262-8270
Open AccessLaser patterned, high-power graphene paper resistor with dual temperature coefficient of resistance
Printing of electronic devices on a paper substrate using 2D graphene-based ink is an opening gate to innovative applications, where devices would be biodegradable, eco-friendly and can be disposed of with negligible impact on the environment. A resistor is a key element of electronic devices and their application area depends upon its power rating and temperature coefficient of resistance (TCR). In this work, in house developed graphene ink is successfully utilized to fabricate a paper-based resistor using a bar coating technique. Dimensional patterning with precise known values of resistance is achieved using a laser with freedom of shape and size which has been explored for the first time on a paper substrate. The resistor has potential to handle ∼7 W power at room temperature with capacity to withstand up to 200 V which is the highest among reported printed resistors. A dual, low and high TCR is observed, correspondingly in cold (173 K to 300 K) and hot (300 K to 373 K) temperature regions with an activation energy Ea of ∼8 meV for the cold region which is 375 percent lower than the hot region (∼30 meV). The dual TCR behaviour is of great importance for application as a stable resistor up to room temperature, and as a thermistor above room temperature.
- 1 September 2018
- Published by Polish Academy of Sciences Chancellery in Opto-Electronics Review
- Vol. 26 (3) , 223-235
Alternative transparent conducting electrode materials for flexible optoelectronic devices
- 1 September 2018
- Published by Polish Academy of Sciences Chancellery in Opto-Electronics Review
- Vol. 26 (3) , 223-235
Alternative transparent conducting electrode materials for flexible optoelectronic devices
- 4 May 2018
- Published by Springer Nature in Pramana
- Vol. 90 (6) , 75
A comparative study of graphene and graphite-based field effect transistor on flexible substrate
- 4 May 2018
- Published by Springer Nature in Pramana
- Vol. 90 (6) , 75
A comparative study of graphene and graphite-based field effect transistor on flexible substrate