Xiaodong Bai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiaodong Bai has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
Yumei Luo
School of New Energy and Materials Southwest Petroleum University Xindu Chengdu China
16 shared publicationsLianci Wu
School of New Energy and Materials, Southwest Petroleum University Chengdu China
5 shared publicationsTao Ning
School of New Energy and Materials, Southwest Petroleum University, Xindu, Chengdu 610500, China
5 shared publications- Yumei Luo
School of New Energy and Materials Southwest Petroleum University Chengdu China
5 shared publications Hua Hu
Exploration Division Petrochina Southwest Oil and Gas Field Company Chengdu China
4 shared publicationsMoubo Wang
School of New Energy and Materials Southwest Petroleum University Chengdu China
4 shared publications
Latest Publications
- 5 November 2026
- Published by Wiley in Journal of Applied Polymer Science
Synthesis and Performance Evaluation of a Cellulose Nanofiber‐Reinforced Filtrate Reducer for Water‐Based Drilling Fluids
To improve the filtration‐control performance and stability of cellulose ether‐based additives under high‐temperature and high‐salinity conditions, a cellulose‐based composite filtrate reducer (HASF) was developed for water‐based drilling fluids. HASF was synthesized by free‐radical graft polymerization of hydroxypropyl methylcellulose (HPMC) with acrylamide, 4‐acryloylmorpholine, and sodium p ‐styrene sulfonate, followed by incorporation of carboxylated cellulose nanofibers (CNF). Synthesis parameters were screened by an L16(4 5 ) orthogonal experimental design with the high‐temperature high‐pressure (HTHP) filtration loss as the response. FT‐IR and 1 H NMR results were consistent with the expected functional groups, and thermogravimetric analysis showed the main mass‐loss process above approximately 200°C. After aging at 160°C for 16 h, the HASF‐containing mud (1 wt% HASF) exhibited an API filtration loss of 8.1 mL versus 92 mL for the base mud, a reduction of approximately 91%, and an HTHP filtration loss of 22 mL. Within the tested ranges (up to 15 wt% NaCl, 1.5 wt% CaCl 2 , or 3 wt% KCl), FL API remained at or below 11 mL. Sand‐disk plugging tests showed reduced filtrate volumes, and SEM revealed a more compact filter cake, indicating the potential of HASF within the temperature, salinity, and formulation ranges investigated.
- 5 November 2026
- Published by Wiley in Journal of Applied Polymer Science
Synthesis and Performance Evaluation of a Cellulose Nanofiber‐Reinforced Filtrate Reducer for Water‐Based Drilling Fluids
To improve the filtration‐control performance and stability of cellulose ether‐based additives under high‐temperature and high‐salinity conditions, a cellulose‐based composite filtrate reducer (HASF) was developed for water‐based drilling fluids. HASF was synthesized by free‐radical graft polymerization of hydroxypropyl methylcellulose (HPMC) with acrylamide, 4‐acryloylmorpholine, and sodium p ‐styrene sulfonate, followed by incorporation of carboxylated cellulose nanofibers (CNF). Synthesis parameters were screened by an L16(4 5 ) orthogonal experimental design with the high‐temperature high‐pressure (HTHP) filtration loss as the response. FT‐IR and 1 H NMR results were consistent with the expected functional groups, and thermogravimetric analysis showed the main mass‐loss process above approximately 200°C. After aging at 160°C for 16 h, the HASF‐containing mud (1 wt% HASF) exhibited an API filtration loss of 8.1 mL versus 92 mL for the base mud, a reduction of approximately 91%, and an HTHP filtration loss of 22 mL. Within the tested ranges (up to 15 wt% NaCl, 1.5 wt% CaCl 2 , or 3 wt% KCl), FL API remained at or below 11 mL. Sand‐disk plugging tests showed reduced filtrate volumes, and SEM revealed a more compact filter cake, indicating the potential of HASF within the temperature, salinity, and formulation ranges investigated.
- 17 May 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (30)
Preparation and Performance Study of Expandable Polymer Plugging Agent for Water‐Based Drilling Fluid
Expanding polymer materials demonstrate significant application value in oil drilling due to their unique volume expansion effects and deformation sealing performance. To investigate polymers with enhanced water absorption and sealing performance, this study employed AM, MMA, and AMPS as ternary copolymer reactants, using white oil as the dispersion medium and OP‐10 and SDS as emulsifiers. Through inverse emulsion polymerization, a three‐dimensional network‐structured expanding polymer P(AM–MMA–AMPS) was synthesized. Optimal synthesis conditions were determined via orthogonal experiments, and comprehensive material characterization revealed successful functional group incorporation with excellent high‐temperature resistance. The polymer exhibits spherical morphology and a median particle size of 33.2 μm, achieving 71.5 g/g water absorption within 24 h at room temperature and 5 MPa pressure resistance. Under the condition of high temperature and high pressure, the polymer can form a dense film on the surface of the mud cake, thereby reducing the filtration loss of the drilling fluid and effectively improving the wellbore stability.
- 17 May 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (30)
Preparation and Performance Study of Expandable Polymer Plugging Agent for Water‐Based Drilling Fluid
Expanding polymer materials demonstrate significant application value in oil drilling due to their unique volume expansion effects and deformation sealing performance. To investigate polymers with enhanced water absorption and sealing performance, this study employed AM, MMA, and AMPS as ternary copolymer reactants, using white oil as the dispersion medium and OP‐10 and SDS as emulsifiers. Through inverse emulsion polymerization, a three‐dimensional network‐structured expanding polymer P(AM–MMA–AMPS) was synthesized. Optimal synthesis conditions were determined via orthogonal experiments, and comprehensive material characterization revealed successful functional group incorporation with excellent high‐temperature resistance. The polymer exhibits spherical morphology and a median particle size of 33.2 μm, achieving 71.5 g/g water absorption within 24 h at room temperature and 5 MPa pressure resistance. Under the condition of high temperature and high pressure, the polymer can form a dense film on the surface of the mud cake, thereby reducing the filtration loss of the drilling fluid and effectively improving the wellbore stability.
- Open Access
Preparation and Application of Cellulose-Based Thermosensitive Polymer in Water-Based Drilling Fluid
The temperature-sensitive plugging agent (HAAN) was synthesized via free-radical graft polymerization using hydroxypropyl methyl cellulose (HPMC), acrylamide (AM), 4-acryloylmorpholine (ACMO) and N-vinyl-2-pyrrolidone (NVP) as the main monomers. HAAN demonstrates potential for addressing the frequent lost circulation problems encountered during the drilling of complex formations. The target product was characterized by FTIR and 1H NMR. Its phase transition behavior was verified via temperature-dependent UV-visible transmittance measurements and high-temperature rheological tests. The experimental results show that the plugging agent possesses good temperature and salt tolerance, and its rheological properties can be enhanced by incorporation into drilling fluid. It demonstrates effective plugging performance both at room temperature and under high-temperature conditions, thereby contributing to improved wellbore stability. It provides a new idea for green multifunctional application of cellulose in water-based drilling fluid.
Open AccessPreparation and Application of Cellulose-Based Thermosensitive Polymer in Water-Based Drilling Fluid
The temperature-sensitive plugging agent (HAAN) was synthesized via free-radical graft polymerization using hydroxypropyl methyl cellulose (HPMC), acrylamide (AM), 4-acryloylmorpholine (ACMO) and N-vinyl-2-pyrrolidone (NVP) as the main monomers. HAAN demonstrates potential for addressing the frequent lost circulation problems encountered during the drilling of complex formations. The target product was characterized by FTIR and 1H NMR. Its phase transition behavior was verified via temperature-dependent UV-visible transmittance measurements and high-temperature rheological tests. The experimental results show that the plugging agent possesses good temperature and salt tolerance, and its rheological properties can be enhanced by incorporation into drilling fluid. It demonstrates effective plugging performance both at room temperature and under high-temperature conditions, thereby contributing to improved wellbore stability. It provides a new idea for green multifunctional application of cellulose in water-based drilling fluid.
- 7 May 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (7) , 5267-5277
Development and Characterization of a Novel Weak‐Gel Agent With Enhanced Salt Tolerance for Solids‐Free Water‐Based Drilling Fluids
In this study, a gel agent for weak‐gel water‐based drilling fluid, poly(acrylamide‐co‐sodium styrene sulfonate‐co‐stearyl methacrylate), abbreviated as SAS, was synthesized via free radical polymerization using acrylamide (AM), sodium styrene sulfonate (SSS), and stearyl methacrylate (SMA) as monomers. The chemical structure, thermal stability, rheological properties, and micromorphology of SAS are characterized and evaluated by Fourier transform infrared spectroscopy (FT‐IR), nuclear magnetic resonance hydrogen spectroscopy ( 1 H NMR), thermogravimetric analysis, environmental scanning electron microscope (ESEM), five point method, and shale rolling recovery experiment. The molecular weight of SAS is 6.85 × 10 5 , confirming its structure aligns with the design. It shows significant viscosity‐increasing ability: the apparent viscosity of 5 wt% SAS aqueous solution reaches 125,800 mPa s at 0.3 rpm and decreases rapidly with increasing shear rate, demonstrating typical shear‐thinning behavior. Under NaCl saturation, the apparent viscosity of 3 wt% SAS solution remains 8200 mPa s at 0.3 rpm, and the shale rolling recovery rate is only 6.37% lower than that in the salt‐free condition. ESEM observation shows SAS forms a dense three‐dimensional network structure in aqueous solution. This study provides an experimental basis for developing salt‐resistant weak‐gel water‐based drilling fluid systems.
- 7 May 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (7) , 5267-5277
Development and Characterization of a Novel Weak‐Gel Agent With Enhanced Salt Tolerance for Solids‐Free Water‐Based Drilling Fluids
In this study, a gel agent for weak‐gel water‐based drilling fluid, poly(acrylamide‐co‐sodium styrene sulfonate‐co‐stearyl methacrylate), abbreviated as SAS, was synthesized via free radical polymerization using acrylamide (AM), sodium styrene sulfonate (SSS), and stearyl methacrylate (SMA) as monomers. The chemical structure, thermal stability, rheological properties, and micromorphology of SAS are characterized and evaluated by Fourier transform infrared spectroscopy (FT‐IR), nuclear magnetic resonance hydrogen spectroscopy ( 1 H NMR), thermogravimetric analysis, environmental scanning electron microscope (ESEM), five point method, and shale rolling recovery experiment. The molecular weight of SAS is 6.85 × 10 5 , confirming its structure aligns with the design. It shows significant viscosity‐increasing ability: the apparent viscosity of 5 wt% SAS aqueous solution reaches 125,800 mPa s at 0.3 rpm and decreases rapidly with increasing shear rate, demonstrating typical shear‐thinning behavior. Under NaCl saturation, the apparent viscosity of 3 wt% SAS solution remains 8200 mPa s at 0.3 rpm, and the shale rolling recovery rate is only 6.37% lower than that in the salt‐free condition. ESEM observation shows SAS forms a dense three‐dimensional network structure in aqueous solution. This study provides an experimental basis for developing salt‐resistant weak‐gel water‐based drilling fluid systems.
- 7 April 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (23) , e70776
Oil‐Absorbing Swelling Pellet P( MMA ‐ AM ‐ DVB ) for Enhancing the Sealing Performance and Wall Stability of Oil‐Based Drilling Fluids
To achieve efficient plugging in oil‐based drilling fluid and enhance wellbore stability, P(MMA‐AM‐DVB) oil‐absorbing expandable particles with excellent oil absorption and high‐temperature resistance were prepared. Methyl methacrylate (MMA) and acrylamide (AM) served as monomers, and divinylbenzene (DVB) as a crosslinking agent, with the optimal formula obtained via molecular structure design. The particles were characterized using FTIR, SEM, TGA‐DSC, contact angle analysis, oil absorption tests, and drilling fluid performance evaluation. The results demonstrated the successful synthesis of P(MMA‐AM‐DVB) with a well‐defined three‐dimensional network structure. The thermal decomposition temperature of P(MMA‐AM‐DVB) was as high as 500°C, indicating excellent thermal stability, and the contact angle between the particles and water was greater than 85°. Oil absorption stabilized within 10 min (with an oil absorption rate > 4.5 g/g) with increased particle size after absorption, demonstrating significant stability and excellent oil absorption capacity. The particles had little impact on the rheology of oil‐based drilling fluid at different aging temperatures; they were able to complete oil absorption, expansion, deformation, and compaction within 30 min before entering formation fractures, thereby achieving effective plugging, thus realizing efficient plugging and supporting wellbore stability.
- 7 April 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (23) , e70776
Oil‐Absorbing Swelling Pellet P( MMA ‐ AM ‐ DVB ) for Enhancing the Sealing Performance and Wall Stability of Oil‐Based Drilling Fluids
To achieve efficient plugging in oil‐based drilling fluid and enhance wellbore stability, P(MMA‐AM‐DVB) oil‐absorbing expandable particles with excellent oil absorption and high‐temperature resistance were prepared. Methyl methacrylate (MMA) and acrylamide (AM) served as monomers, and divinylbenzene (DVB) as a crosslinking agent, with the optimal formula obtained via molecular structure design. The particles were characterized using FTIR, SEM, TGA‐DSC, contact angle analysis, oil absorption tests, and drilling fluid performance evaluation. The results demonstrated the successful synthesis of P(MMA‐AM‐DVB) with a well‐defined three‐dimensional network structure. The thermal decomposition temperature of P(MMA‐AM‐DVB) was as high as 500°C, indicating excellent thermal stability, and the contact angle between the particles and water was greater than 85°. Oil absorption stabilized within 10 min (with an oil absorption rate > 4.5 g/g) with increased particle size after absorption, demonstrating significant stability and excellent oil absorption capacity. The particles had little impact on the rheology of oil‐based drilling fluid at different aging temperatures; they were able to complete oil absorption, expansion, deformation, and compaction within 30 min before entering formation fractures, thereby achieving effective plugging, thus realizing efficient plugging and supporting wellbore stability.
- 18 March 2026
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 50 (13) , 5631-5646
A robust PHDI-crosslinked cellulose aerogel loaded with CaCO 3 for Congo red removal
A robust CaCO 3 /CA-PHDI aerogel via crosslinking & in situ mineralization achieves 191.6 mg g −1 Congo red adsorption, pH 3–11 tolerance, and >73% regeneration. The mechanism involves Ca 2+ coordination, hydrogen bonding, and electrostatic interactions.
- 18 March 2026
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 50 (13) , 5631-5646
A robust PHDI-crosslinked cellulose aerogel loaded with CaCO 3 for Congo red removal
A robust CaCO 3 /CA-PHDI aerogel via crosslinking & in situ mineralization achieves 191.6 mg g −1 Congo red adsorption, pH 3–11 tolerance, and >73% regeneration. The mechanism involves Ca 2+ coordination, hydrogen bonding, and electrostatic interactions.
- 15 September 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (2)
Preparation and Performance Characterization of Novel Shale Inhibitors
In order to reduce the huge economic loss caused by clay hydration and swelling during drilling, it is very important to select shale inhibitors reasonably and efficiently. In recent years, ionic liquids have been active in various industries as a new material, among which 1‐vinyl‐3‐ethylimidazole bromide salt has high temperature tolerance and certain inhibition ability. Therefore, in this paper, 1‐vinyl‐3‐ethylimidazole bromide salt was used as a water‐based drilling fluid inhibitor monomer, and the ionic polymer inhibitor (PIAA) were prepared by solution polymerization. The optimal synthesis conditions were determined by designing orthogonal experiments, and the properties of the materials were tested and evaluated. The experimental results show that PIAA is able to withstand temperatures up to 270°C. Compared with deionized water, the size of the mud ball after soaking in PIAA solution is smaller, and the linear expansion rate of bentonite in PIAA solution for 24 h is 29%. The shale recovery rate at 160°C was 86.5%, which was higher than that of deionized water (36.6%). When the base slurry is added, the zeta potential changes from negative to positive. XRD tests show that PIAA effectively compresses the bentonite bi‐layer. After the addition of PIAA to the base pulp, the particle size of bentonite particles increased and the distribution was more concentrated. It also has good performance in the contact angle test and scanning electron microscope test, and at the same time will not damage the rheological properties of the base pulp and has a certain performance of reducing filtration loss.
- 15 September 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (2)
Preparation and Performance Characterization of Novel Shale Inhibitors
In order to reduce the huge economic loss caused by clay hydration and swelling during drilling, it is very important to select shale inhibitors reasonably and efficiently. In recent years, ionic liquids have been active in various industries as a new material, among which 1‐vinyl‐3‐ethylimidazole bromide salt has high temperature tolerance and certain inhibition ability. Therefore, in this paper, 1‐vinyl‐3‐ethylimidazole bromide salt was used as a water‐based drilling fluid inhibitor monomer, and the ionic polymer inhibitor (PIAA) were prepared by solution polymerization. The optimal synthesis conditions were determined by designing orthogonal experiments, and the properties of the materials were tested and evaluated. The experimental results show that PIAA is able to withstand temperatures up to 270°C. Compared with deionized water, the size of the mud ball after soaking in PIAA solution is smaller, and the linear expansion rate of bentonite in PIAA solution for 24 h is 29%. The shale recovery rate at 160°C was 86.5%, which was higher than that of deionized water (36.6%). When the base slurry is added, the zeta potential changes from negative to positive. XRD tests show that PIAA effectively compresses the bentonite bi‐layer. After the addition of PIAA to the base pulp, the particle size of bentonite particles increased and the distribution was more concentrated. It also has good performance in the contact angle test and scanning electron microscope test, and at the same time will not damage the rheological properties of the base pulp and has a certain performance of reducing filtration loss.
- 10 April 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (27)
Preparation and Performance Evaluation of Oil‐Absorbing Expansive Particles for Oil‐Based Drilling Fluid
With the development of deep and ultradeep wells advances, oil‐based drilling fluids play a significant role. To enhance the plugging performance of oil‐based drilling fluids, this study synthesizes an oil‐absorbing expandable particle, P(AM‐SMA‐St‐DVB), which was prepared by solution polymerization and used acrylamide (AM), stearyl methacrylate (SMA), styrene (St) as reaction monomers; divinylbenzene (DVB) as a cross‐linking agent; polyvinylpyrrolidone (PVP) as a dispersant and 2,2′‐azobis (AIBN) as an initiator. Through methods including Fourier‐transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), thermogravimetric analysis‐differential scanning calorimetry (TGA‐DSC), contact angle analysis, particle size analysis, oil absorption testing, and oil‐based drilling fluid performance testing, the structure and properties of this particle were investigated. The results indicate the successful synthesis of the target product with a well‐defined three‐dimensional network structure. The particle demonstrates excellent thermal stability, remaining nearly intact until around 450°C. The contact angle between the particles and water exceeds 90°, indicating its hydrophobic and oleophilic nature. Oil absorption levels stabilize within 10 min with an absorption ratio exceeding four across various temperatures, showing significant stability and excellent absorption capacity. When added to the drilling fluid system, P(AM‐SMA‐St‐DVB) particles reduce fluid loss at ambient and high temperatures as well as after aging, while maintaining stable rheological properties for oil‐based drilling fluids.
- 10 April 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (27)
Preparation and Performance Evaluation of Oil‐Absorbing Expansive Particles for Oil‐Based Drilling Fluid
With the development of deep and ultradeep wells advances, oil‐based drilling fluids play a significant role. To enhance the plugging performance of oil‐based drilling fluids, this study synthesizes an oil‐absorbing expandable particle, P(AM‐SMA‐St‐DVB), which was prepared by solution polymerization and used acrylamide (AM), stearyl methacrylate (SMA), styrene (St) as reaction monomers; divinylbenzene (DVB) as a cross‐linking agent; polyvinylpyrrolidone (PVP) as a dispersant and 2,2′‐azobis (AIBN) as an initiator. Through methods including Fourier‐transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), thermogravimetric analysis‐differential scanning calorimetry (TGA‐DSC), contact angle analysis, particle size analysis, oil absorption testing, and oil‐based drilling fluid performance testing, the structure and properties of this particle were investigated. The results indicate the successful synthesis of the target product with a well‐defined three‐dimensional network structure. The particle demonstrates excellent thermal stability, remaining nearly intact until around 450°C. The contact angle between the particles and water exceeds 90°, indicating its hydrophobic and oleophilic nature. Oil absorption levels stabilize within 10 min with an absorption ratio exceeding four across various temperatures, showing significant stability and excellent absorption capacity. When added to the drilling fluid system, P(AM‐SMA‐St‐DVB) particles reduce fluid loss at ambient and high temperatures as well as after aging, while maintaining stable rheological properties for oil‐based drilling fluids.
- 23 March 2025
- Published by Wiley in Journal of Polymer Science
Self‐Healing Hydrogel Blocking Agent Based on Borate Bonding‐Hydrophobic Binding Dual Network
Borehole wall instability is one of the most serious problems in drilling and completion, and the most common way to solve the problem is to stabilize the borehole wall with sealing materials. This work reports the synthesis, characterization, and evaluation of the double network self‐healing hydrogel containing acrylamide (AM), 2‐acrylamide‐2‐methylpropane sulfonic acid (AMPS), polyvinyl alcohol (PVA) and borax to use as a plugging agent for drilling fluids. The experimental results show that P (AM‐co‐AMPS‐co‐LMA)/PVA DN hydrogel has good temperature and salt resistance. There are a large number of holes in the interior, and the swelling ratio is as high as 217.33%. The mechanical properties test showed that the hydrogel had a high tensile strength of 0.57 MPa and elongation at break of 464.63%. The recovery efficiency of elongation at break is over 87%. Through the pressure plugging test, the steel model with crack widths of 0.5 mm and 1 mm was adopted. 0.8% P(AM‐co‐AMPS‐co‐LMA)/PVA DN hydrogel could withstand the pressure of 5 MPa at 70°C. This kind of hydrogel with good mechanical properties and certain self‐healing properties can be a new material to control leakage.
- 23 March 2025
- Published by Wiley in Journal of Polymer Science
Self‐Healing Hydrogel Blocking Agent Based on Borate Bonding‐Hydrophobic Binding Dual Network
Borehole wall instability is one of the most serious problems in drilling and completion, and the most common way to solve the problem is to stabilize the borehole wall with sealing materials. This work reports the synthesis, characterization, and evaluation of the double network self‐healing hydrogel containing acrylamide (AM), 2‐acrylamide‐2‐methylpropane sulfonic acid (AMPS), polyvinyl alcohol (PVA) and borax to use as a plugging agent for drilling fluids. The experimental results show that P (AM‐co‐AMPS‐co‐LMA)/PVA DN hydrogel has good temperature and salt resistance. There are a large number of holes in the interior, and the swelling ratio is as high as 217.33%. The mechanical properties test showed that the hydrogel had a high tensile strength of 0.57 MPa and elongation at break of 464.63%. The recovery efficiency of elongation at break is over 87%. Through the pressure plugging test, the steel model with crack widths of 0.5 mm and 1 mm was adopted. 0.8% P(AM‐co‐AMPS‐co‐LMA)/PVA DN hydrogel could withstand the pressure of 5 MPa at 70°C. This kind of hydrogel with good mechanical properties and certain self‐healing properties can be a new material to control leakage.
- 19 January 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (15)
Synthesis and Application of a Temperature Sensitive Poly(Acrylamide‐Co‐N‐Isopropylacrylamide‐Co‐Sodium P‐Styrene Sulfonate) as a New Water‐Based Drilling Fluid Plugging Agent
In the process of oil and gas production, the failure of drilling fluid caused it to invade the formation, leading to wellbore instability. N‐isopropylacrylamide (NIPAM), acrylamide (AM), and sodium p‐styrene sulfonate (SSS) were used as raw materials, and the P(NIPAM/AM/SSS) (abbreviated as NAS) temperature‐sensitive plugging agent was synthesized by inverse emulsion polymerization. The optimum synthesis conditions were obtained using a redox initiation system. Infrared measurements and UV–visible analysis showed that the target product was successfully prepared, and NAS exhibited a lower critical solution temperature (LCST) of 55°C, with sensitive temperature‐responsive behavior. Rheological and filtration tests, along with high‐temperature and high‐pressure (HTHP) sand tray tests, demonstrated that the temperature‐sensitive plugging agent effectively plugged the formation. Particle size analysis and Zeta potential analysis indicated that the addition of the temperature‐sensitive plugging agent increased the electrostatic stability of bentonite‐based slurry and polymer. Contact angle measurements and micro‐morphology of the mud cake revealed that a hydrophilic‐hydrophobic transition occurred at high temperatures in NAS, forming a dense hydrophobic film on the surface of the mud cake. This film effectively sealed cracks and micropores, reduced the invasion of free water, and improved wellbore stability.
- 19 January 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (15)
Synthesis and Application of a Temperature Sensitive Poly(Acrylamide‐Co‐N‐Isopropylacrylamide‐Co‐Sodium P‐Styrene Sulfonate) as a New Water‐Based Drilling Fluid Plugging Agent
In the process of oil and gas production, the failure of drilling fluid caused it to invade the formation, leading to wellbore instability. N‐isopropylacrylamide (NIPAM), acrylamide (AM), and sodium p‐styrene sulfonate (SSS) were used as raw materials, and the P(NIPAM/AM/SSS) (abbreviated as NAS) temperature‐sensitive plugging agent was synthesized by inverse emulsion polymerization. The optimum synthesis conditions were obtained using a redox initiation system. Infrared measurements and UV–visible analysis showed that the target product was successfully prepared, and NAS exhibited a lower critical solution temperature (LCST) of 55°C, with sensitive temperature‐responsive behavior. Rheological and filtration tests, along with high‐temperature and high‐pressure (HTHP) sand tray tests, demonstrated that the temperature‐sensitive plugging agent effectively plugged the formation. Particle size analysis and Zeta potential analysis indicated that the addition of the temperature‐sensitive plugging agent increased the electrostatic stability of bentonite‐based slurry and polymer. Contact angle measurements and micro‐morphology of the mud cake revealed that a hydrophilic‐hydrophobic transition occurred at high temperatures in NAS, forming a dense hydrophobic film on the surface of the mud cake. This film effectively sealed cracks and micropores, reduced the invasion of free water, and improved wellbore stability.