Taekjin Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Taekjin Lee has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Taku Nonomura
Tohoku University
3 shared publications Keisuke Asai
Department of Aerospace Engineering, Tohoku University, Sendai, Japan
2 shared publications- Christian Klein
Institute of Aerodynamics and Flow Technology, German Aerospace Center (DLR)
1 shared publication - Jonathan W. Naughton
University of Wyoming
1 shared publication - Keisuke Asai
Tohoku University
1 shared publication - Marco Costantini
Deutsches Zentrum für Luft- und Raumfahrt e.V. (DLR)
1 shared publication
Latest Publications
- Open Access
- 8 January 2021
- Published by Springer Nature in Experiments in Fluids
- Vol. 62 (1) , 1-34
Feasibility of skin-friction field measurements in a transonic wind tunnel using a global luminescent oil film
The feasibility of skin-friction field measurements using the global luminescent oil-film skin-friction field estimation method was evaluated for a challenging case of a supercritical airfoil model under transonic wind-tunnel conditions (freestream Mach number of 0.72) at a high Reynolds number (10 million, based on the model chord length). The oil-film thickness and skin-friction coefficient distributions were estimated over the airfoil model upper surface for a range of angles of attack (from $$-0.4^{\circ }$$ to $$2.0^{\circ }$$ ), thus enabling the study of different boundary-layer stability situations with laminar–turbulent transition, including cases with shock-wave/boundary-layer interaction. Conventional pressure measurements on the surface and in the wake of the model as well as Schlieren flow visualizations were conducted to support the oil-film based investigations. In the laminar-flow regions, the oil-film thickness could be generally kept below the critical limit of roughness that would induce premature boundary-layer transition. The skin friction in this region could be estimated with a moderate confidence level, as confirmed for portions of the chord by the reasonable agreement with numerical data obtained via laminar boundary-layer computations. Moreover, the location of transition onset was evaluated from the skin-friction estimations with relatively low uncertainty, thus enabling the examination of the transition location evolution with varying angle of attack. The estimated locations of transition onset were shown to be in general agreement with reference transition locations measured via temperature-sensitive paint. On the other hand, the oil-film thickness in the turbulent-flow regions was larger than the height of the viscous sublayer, which led to an hydraulically rough surface with increased skin friction, as compared to the clean configuration. For this reason, quantitative skin-friction estimations were not feasible in the turbulent-flow regions. The global effects of the oil-film setup on the flow around the airfoil were evaluated from the estimations of the aerodynamic coefficients. In particular, it was shown that the presence of the specific base coat used for the application of the oil film already induced a significant increase in airfoil drag, as compared to the clean configuration, whereas a thin oil film led to negligible or small additional increases in drag. Based on the present observations, considerations for the further improvement of the global luminescent oil-film skin-friction field estimation method in transonic flow experiments at high Reynolds numbers are elucidated. Graphic- 8 January 2021
- Published by Springer Nature in Experiments in Fluids
- Vol. 62 (1) , 1-34
Open AccessFeasibility of skin-friction field measurements in a transonic wind tunnel using a global luminescent oil film
The feasibility of skin-friction field measurements using the global luminescent oil-film skin-friction field estimation method was evaluated for a challenging case of a supercritical airfoil model under transonic wind-tunnel conditions (freestream Mach number of 0.72) at a high Reynolds number (10 million, based on the model chord length). The oil-film thickness and skin-friction coefficient distributions were estimated over the airfoil model upper surface for a range of angles of attack (from $$-0.4^{\circ }$$ to $$2.0^{\circ }$$ ), thus enabling the study of different boundary-layer stability situations with laminar–turbulent transition, including cases with shock-wave/boundary-layer interaction. Conventional pressure measurements on the surface and in the wake of the model as well as Schlieren flow visualizations were conducted to support the oil-film based investigations. In the laminar-flow regions, the oil-film thickness could be generally kept below the critical limit of roughness that would induce premature boundary-layer transition. The skin friction in this region could be estimated with a moderate confidence level, as confirmed for portions of the chord by the reasonable agreement with numerical data obtained via laminar boundary-layer computations. Moreover, the location of transition onset was evaluated from the skin-friction estimations with relatively low uncertainty, thus enabling the examination of the transition location evolution with varying angle of attack. The estimated locations of transition onset were shown to be in general agreement with reference transition locations measured via temperature-sensitive paint. On the other hand, the oil-film thickness in the turbulent-flow regions was larger than the height of the viscous sublayer, which led to an hydraulically rough surface with increased skin friction, as compared to the clean configuration. For this reason, quantitative skin-friction estimations were not feasible in the turbulent-flow regions. The global effects of the oil-film setup on the flow around the airfoil were evaluated from the estimations of the aerodynamic coefficients. In particular, it was shown that the presence of the specific base coat used for the application of the oil film already induced a significant increase in airfoil drag, as compared to the clean configuration, whereas a thin oil film led to negligible or small additional increases in drag. Based on the present observations, considerations for the further improvement of the global luminescent oil-film skin-friction field estimation method in transonic flow experiments at high Reynolds numbers are elucidated. Graphic - 31 December 2019
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 31 (3) , 035204
Validation and uncertainty analysis of global luminescent oil-film skin-friction field measurement
Results from a skin-friction-field measurement method using global luminescent oil-film images, in which the oil film covers a large portion of the surface, were examined by comparing them with those obtained from conventional hot-wire measurements. The measurement processes including calibrations, oil-film image acquisition, and image processing are explained, and error sources are analyzed. The experimental results show that the skin frictions measured by both methods in a turbulent boundary layer on a flat surface agree when the oil-film thickness is less than the height of the viscous sublayer (corresponding to an oil-film thickness of less than five wall units). The uncertainty of the measurements is presented. When the measurement conditions were optimum (illumination, exposure time, frame rate, oil height, etc), the uncertainty was approximately 3%–4%.
- 31 December 2019
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 31 (3) , 035204
Validation and uncertainty analysis of global luminescent oil-film skin-friction field measurement
Results from a skin-friction-field measurement method using global luminescent oil-film images, in which the oil film covers a large portion of the surface, were examined by comparing them with those obtained from conventional hot-wire measurements. The measurement processes including calibrations, oil-film image acquisition, and image processing are explained, and error sources are analyzed. The experimental results show that the skin frictions measured by both methods in a turbulent boundary layer on a flat surface agree when the oil-film thickness is less than the height of the viscous sublayer (corresponding to an oil-film thickness of less than five wall units). The uncertainty of the measurements is presented. When the measurement conditions were optimum (illumination, exposure time, frame rate, oil height, etc), the uncertainty was approximately 3%–4%.
- 1 June 2018
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 89 (6) , 065106
Linear least-squares method for global luminescent oil film skin friction field analysis
A data analysis method based on the linear least-squares (LLS) method was developed for the extraction of high-resolution skin friction fields from global luminescent oil film (GLOF) visualization images of a surface in an aerodynamic flow. In this method, the oil film thickness distribution and its spatiotemporal development are measured by detecting the luminescence intensity of the thin oil film. From the resulting set of GLOF images, the thin oil film equation is solved to obtain an ensemble-averaged (steady) skin friction field as an inverse problem. In this paper, the formulation of a discrete linear system of equations for the LLS method is described, and an error analysis is given to identify the main error sources and the relevant parameters. Simulations were conducted to evaluate the accuracy of the LLS method and the effects of the image patterns, image noise, and sample numbers on the results in comparison with the previous snapshot-solution-averaging (SSA) method. An experimental case is shown to enable the comparison of the results obtained using conventional oil flow visualization and those obtained using both the LLS and SSA methods. The overall results show that the LLS method is more reliable than the SSA method and the LLS method can yield a more detailed skin friction topology in an objective way.
- 1 June 2018
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 89 (6) , 065106
Linear least-squares method for global luminescent oil film skin friction field analysis
A data analysis method based on the linear least-squares (LLS) method was developed for the extraction of high-resolution skin friction fields from global luminescent oil film (GLOF) visualization images of a surface in an aerodynamic flow. In this method, the oil film thickness distribution and its spatiotemporal development are measured by detecting the luminescence intensity of the thin oil film. From the resulting set of GLOF images, the thin oil film equation is solved to obtain an ensemble-averaged (steady) skin friction field as an inverse problem. In this paper, the formulation of a discrete linear system of equations for the LLS method is described, and an error analysis is given to identify the main error sources and the relevant parameters. Simulations were conducted to evaluate the accuracy of the LLS method and the effects of the image patterns, image noise, and sample numbers on the results in comparison with the previous snapshot-solution-averaging (SSA) method. An experimental case is shown to enable the comparison of the results obtained using conventional oil flow visualization and those obtained using both the LLS and SSA methods. The overall results show that the LLS method is more reliable than the SSA method and the LLS method can yield a more detailed skin friction topology in an objective way.