Liaofei Yin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Liaofei Yin has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Li Jia
Institute of Thermal Engineering, School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044, China; Beijing Key Laboratory of Flow and Heat Transfer of Phase Changing in Micro and Small Scale, Beijing 100044, China
7 shared publications Chao Dang
6 shared publicationsYi Ding
6 shared publicationsLi Jia
5 shared publicationsTianjun Qin
5 shared publicationsWenhao Ma
5 shared publications
Latest Publications
- 30 July 2026
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 230
Orientation effect on flow boiling heat transfer in aluminum heat sink with open microchannels
- 30 July 2026
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 230
Orientation effect on flow boiling heat transfer in aluminum heat sink with open microchannels
- 8 January 2026
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 224
Experimental investigation on HFE-7100 flow boiling in aluminum open microchannels heat sink
- 8 January 2026
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 224
Experimental investigation on HFE-7100 flow boiling in aluminum open microchannels heat sink
- 23 September 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 280
HFE-7100 flow boiling in open microchannels with grid-patterned multiscale textures
- 23 September 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 280
HFE-7100 flow boiling in open microchannels with grid-patterned multiscale textures
- Open Access
- 20 January 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 66
Experimental study on the heat transfer performance of vapor chamber with uniform/gradient wicks
- 20 January 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 66
Open AccessExperimental study on the heat transfer performance of vapor chamber with uniform/gradient wicks
- Open Access
- 1 January 2025
- Published by Tech Science Press in Frontiers in Heat and Mass Transfer
- Vol. 23 (3) , 751-764
Enhanced Flow Boiling Heat Transfer of HFE-7100 in Open Microchannels Using Micro-Nano Composite Structures
Flow boiling in open microchannels offers highly efficient heat transfer performance and has attracted increasing attention in the fields of heat transfer and thermal management of electronic devices in recent years. However,... | Find, read and cite all the research you need on Tech Science Press
- 1 January 2025
- Published by Tech Science Press in Frontiers in Heat and Mass Transfer
- Vol. 23 (3) , 751-764
Open AccessEnhanced Flow Boiling Heat Transfer of HFE-7100 in Open Microchannels Using Micro-Nano Composite Structures
Flow boiling in open microchannels offers highly efficient heat transfer performance and has attracted increasing attention in the fields of heat transfer and thermal management of electronic devices in recent years. However,... | Find, read and cite all the research you need on Tech Science Press
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Boiling bubble behaviors of fluids of different surface tensions on heating surfaces with micro/nanostructures
The use of environmentally friendly coolants with low surface tension in boiling applications holds great promise, and the implementation of micro/nanostructures is widely regarded as an effective strategy for enhancing boiling heat transfer. However, as a critical factor influencing the boiling process, the understanding of boiling bubble behavior on micro/nanostructured modified surfaces remains insufficient for the low surface tension fluids. SF-33, with its zero ozone depletion potential and extremely low global warming potential, is gradually gaining attention in the field of boiling as a representative low-surface-tension fluid. Herein, several copper heating surfaces with micro or micro/nanocomposite structures were fabricated using sintering copper mesh and thermal oxidation techniques. The bubble growth and departure phenomena during pool boiling of coolants SF-33 and de-ionized water on these micro/nanostructured surfaces were investigated and comparatively analyzed. The saturated pool boiling experiments were conducted at atmospheric pressure. It was observed that on smooth flat surface and sintered wire-mesh flat surface, SF-33 bubbles exhibited a faster growth rate, higher departure frequency, and smaller departure diameter. However, on the sintered wire-mesh flat surface with nanowires, de-ionized water bubbles demonstrated a higher departure frequency, while the growth rate and departure diameter were similar to those of SF-33 bubbles. In addition, it was found that the influence of microstructures on de-ionized water bubble behaviors is significantly lower than that of micro/nanocomposite structures, while for SF-33, increasing the microstructures alone can greatly affect bubble growth and departure, with further changes induced by the addition of nanostructures being relatively minor.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Boiling bubble behaviors of fluids of different surface tensions on heating surfaces with micro/nanostructures
The use of environmentally friendly coolants with low surface tension in boiling applications holds great promise, and the implementation of micro/nanostructures is widely regarded as an effective strategy for enhancing boiling heat transfer. However, as a critical factor influencing the boiling process, the understanding of boiling bubble behavior on micro/nanostructured modified surfaces remains insufficient for the low surface tension fluids. SF-33, with its zero ozone depletion potential and extremely low global warming potential, is gradually gaining attention in the field of boiling as a representative low-surface-tension fluid. Herein, several copper heating surfaces with micro or micro/nanocomposite structures were fabricated using sintering copper mesh and thermal oxidation techniques. The bubble growth and departure phenomena during pool boiling of coolants SF-33 and de-ionized water on these micro/nanostructured surfaces were investigated and comparatively analyzed. The saturated pool boiling experiments were conducted at atmospheric pressure. It was observed that on smooth flat surface and sintered wire-mesh flat surface, SF-33 bubbles exhibited a faster growth rate, higher departure frequency, and smaller departure diameter. However, on the sintered wire-mesh flat surface with nanowires, de-ionized water bubbles demonstrated a higher departure frequency, while the growth rate and departure diameter were similar to those of SF-33 bubbles. In addition, it was found that the influence of microstructures on de-ionized water bubble behaviors is significantly lower than that of micro/nanocomposite structures, while for SF-33, increasing the microstructures alone can greatly affect bubble growth and departure, with further changes induced by the addition of nanostructures being relatively minor.
- Open Access
- 10 December 2023
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 53
Optimization research on battery thermal management system based on PCM and mini-channel cooling plates
- 10 December 2023
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 53
Open AccessOptimization research on battery thermal management system based on PCM and mini-channel cooling plates
- 23 August 2023
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 194
Flow pattern transitions and liquid mass transfer resistance of binary zeotropic mixtures during flow boiling
- 23 August 2023
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 194
Flow pattern transitions and liquid mass transfer resistance of binary zeotropic mixtures during flow boiling