Narendran Raghavan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Narendran Raghavan has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- John A. Turner
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
4 shared publications - Ryan Dehoff
ORNL
4 shared publications - Suresh Sudharsanam Babu
Department of Materials Science and Engineering, University of Maryland, College Park, MD, USA
4 shared publications Michael Kirka
2 shared publications- Michael Kirka
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
2 shared publications - Neil Carlson
Los Alamos National Lab. (LANL), Los Alamos, NM (United States)
2 shared publications
Latest Publications
- 1 January 2022
- Published by Elsevier in Materials Letters
- Vol. 307
Investigation of interfacial structures for hybrid manufacturing
- 1 January 2022
- Published by Elsevier in Materials Letters
- Vol. 307
Investigation of interfacial structures for hybrid manufacturing
- 1 October 2018
- Published by Office of Scientific and Technical Information (OSTI)
Fluid Dynamics Effects on Microstructure Prediction in Single Laser Tracks for Additive Manufacturing
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 October 2018
- Published by Office of Scientific and Technical Information (OSTI)
Fluid Dynamics Effects on Microstructure Prediction in Single Laser Tracks for Additive Manufacturing
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 June 2018
- Published by Office of Scientific and Technical Information (OSTI)
Controlling microstructure in deposits fabricated using powder blown direct energy deposition technique
The overall goal of this collaboration is to develop technologies to control grain morphology and microstructures of Inconel 718 components additively manufactured through the Direct Energy Deposition (DED) process (Identical to the LENS (laser engineered net shaping) processes) and to achieve equiaxed or near equiaxed grain structures. The phase1 technical collaboration was used to fabricate Inconel 718 builds with different process parameters, pre heat and scan strategies. The results were then rationalized using computational heat transfer and solidification models. Microstructural characterization showed that the aspect ratio of the grains can be reduced to less than 1.5, and that control of the grain sizes to within 50-100 μm could be potentially obtained by using an external source to preheat the substrate to 400 ̊C. Heat transfer models coupled with solidification models were used to rationalize the results which show that preheating lowered the temperature gradient thereby resulting in moving towards the equiaxed region of the columnar to equiaxed transition (CET) curve. The results demonstrate that higher preheat temperatures could be potentially used to obtain a truly equiaxed structure.
- 1 June 2018
- Published by Office of Scientific and Technical Information (OSTI)
Controlling microstructure in deposits fabricated using powder blown direct energy deposition technique
The overall goal of this collaboration is to develop technologies to control grain morphology and microstructures of Inconel 718 components additively manufactured through the Direct Energy Deposition (DED) process (Identical to the LENS (laser engineered net shaping) processes) and to achieve equiaxed or near equiaxed grain structures. The phase1 technical collaboration was used to fabricate Inconel 718 builds with different process parameters, pre heat and scan strategies. The results were then rationalized using computational heat transfer and solidification models. Microstructural characterization showed that the aspect ratio of the grains can be reduced to less than 1.5, and that control of the grain sizes to within 50-100 μm could be potentially obtained by using an external source to preheat the substrate to 400 ̊C. Heat transfer models coupled with solidification models were used to rationalize the results which show that preheating lowered the temperature gradient thereby resulting in moving towards the equiaxed region of the columnar to equiaxed transition (CET) curve. The results demonstrate that higher preheat temperatures could be potentially used to obtain a truly equiaxed structure.
- Top Cited Papers
- 1 November 2017
- Published by Elsevier in Acta Materialia
- Vol. 140, 375-387
Localized melt-scan strategy for site specific control of grain size and primary dendrite arm spacing in electron beam additive manufacturing
- 1 November 2017
- Published by Elsevier in Acta Materialia
- Vol. 140, 375-387
Top Cited PapersLocalized melt-scan strategy for site specific control of grain size and primary dendrite arm spacing in electron beam additive manufacturing
- Top Cited Papers
- 1 June 2016
- Published by Elsevier in Acta Materialia
- Vol. 112, 303-314
Numerical modeling of heat-transfer and the influence of process parameters on tailoring the grain morphology of IN718 in electron beam additive manufacturing
- 1 June 2016
- Published by Elsevier in Acta Materialia
- Vol. 112, 303-314
Top Cited PapersNumerical modeling of heat-transfer and the influence of process parameters on tailoring the grain morphology of IN718 in electron beam additive manufacturing
- 12 February 2016
- Published by Springer Nature in JOM
- Vol. 68 (3) , 1012-1020
Microstructure Development in Electron Beam-Melted Inconel 718 and Associated Tensile Properties
- 12 February 2016
- Published by Springer Nature in JOM
- Vol. 68 (3) , 1012-1020
Microstructure Development in Electron Beam-Melted Inconel 718 and Associated Tensile Properties