Jiri Balla
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jiri Balla has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Zbynek Krist
Univ Def Brno, Dept Weap & Ammunit, Brno, Czech Republic
3 shared publicationsBeáta Kopiláková
Alexander Dubček University of Trenčín
1 shared publication- Dung Nguyen Van
Faculty of Pharmacy, University of Medicine and Pharmacy, Hue University
1 shared publication Ich Le Cong
University of Defence, Kounicova 65, 662 10 Brno, Czech Republic
1 shared publicationMichal Kovarik
Faculty of Military Technology, University of Defence, Kounicova
1 shared publicationMinh Phu Nguyen
1 shared publication
Latest Publications
- Open Access
- 1 May 2026
- Published by KEAI Publishing in Defence Technology
Study on the influence of buttstock elasticity on the firing stability of an automatic rifle
- 1 May 2026
- Published by KEAI Publishing in Defence Technology
Open AccessStudy on the influence of buttstock elasticity on the firing stability of an automatic rifle
- 19 June 2025
- Published by Trans Tech Publications, Ltd. in Advances in Science and Technology
- Vol. 167, 65-80
The Main Problems in the Operation of Ramming Devices in Artillery Weapons
The article discusses the principles of operation of loading devices of artillery weapons with a focus on the ramming device as the most important part performing mechanical movement with the round. The attention is focused on hydraulically driven ramming devices, where the possibility of using linear and rotary hydraulic drives is investigated. At the same time, the possibilities of experimental determination of model parameters such as motor damping coefficients, hydraulic resistances, reduced values of compressibility coefficients in the given circuit are presented. The advantages and disadvantages of the used flowmeters are shown for their comparison, from which it is possible to derive the velocity of insertion of round parts. The determined parameters are used for modelling the movement of the rammer and the projectile. Experimental procedures can also be used for the diagnosis and technical control of ramming devices according to national defense standards based on STANAG standards and calculation methods when upgrading existing hydraulically driven loading devices.
- 19 June 2025
- Published by Trans Tech Publications, Ltd. in Advances in Science and Technology
- Vol. 167, 65-80
The Main Problems in the Operation of Ramming Devices in Artillery Weapons
The article discusses the principles of operation of loading devices of artillery weapons with a focus on the ramming device as the most important part performing mechanical movement with the round. The attention is focused on hydraulically driven ramming devices, where the possibility of using linear and rotary hydraulic drives is investigated. At the same time, the possibilities of experimental determination of model parameters such as motor damping coefficients, hydraulic resistances, reduced values of compressibility coefficients in the given circuit are presented. The advantages and disadvantages of the used flowmeters are shown for their comparison, from which it is possible to derive the velocity of insertion of round parts. The determined parameters are used for modelling the movement of the rammer and the projectile. Experimental procedures can also be used for the diagnosis and technical control of ramming devices according to national defense standards based on STANAG standards and calculation methods when upgrading existing hydraulically driven loading devices.
- Open Access
- 1 March 2024
- Published by KEAI Publishing in Defence Technology
- Vol. 33, 42-54
Study of relationship between motion of mechanisms in gas operated weapon and its shock absorber
- 1 March 2024
- Published by KEAI Publishing in Defence Technology
- Vol. 33, 42-54
Open AccessStudy of relationship between motion of mechanisms in gas operated weapon and its shock absorber
- Open Access
- 11 September 2015
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 65 (5) , 356-362
Technical Diagnostics of Tank Cannon Smooth Barrel Bore and Ramming Device
The technical diagnostics of 125 mm tank cannon 2A46 smooth barrel and ramming devices are discussed respectively. Focuses on barrel diagnostics and suggests new procedures based on reconstructed BG20 Gun Barrel Bore Gauge System, measuring internal diameter of the barrel bore. The new system measures throughout the whole barrel bore the inner diameter not only at the beginning of barrel bore as it was usually measured before. Different nature of barrel wear was revealed between barrels firing sub-calibre and high explosive projectiles. A method for ramming device diagnostics is presented. An accurate method was proposed, determining projectile extraction force from barrel, as one of the main ramming device parameters for weapons that are used in all areas of armed forces. Results are based on experimental methods assessing the extraction forces from barrel after projectile loading. These tests were performed as a series of tests with consequent technical diagnostics according to the new Czech Defence Standards (derived from NATO standards). The results are presented as the new methodologies for diagnostics of 125 mm barrel 2A46 and ramming devices of tank T-72 for use by technical logistic units in the Czech Republic Armed Forces.
- 11 September 2015
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 65 (5) , 356-362
Open AccessTechnical Diagnostics of Tank Cannon Smooth Barrel Bore and Ramming Device
The technical diagnostics of 125 mm tank cannon 2A46 smooth barrel and ramming devices are discussed respectively. Focuses on barrel diagnostics and suggests new procedures based on reconstructed BG20 Gun Barrel Bore Gauge System, measuring internal diameter of the barrel bore. The new system measures throughout the whole barrel bore the inner diameter not only at the beginning of barrel bore as it was usually measured before. Different nature of barrel wear was revealed between barrels firing sub-calibre and high explosive projectiles. A method for ramming device diagnostics is presented. An accurate method was proposed, determining projectile extraction force from barrel, as one of the main ramming device parameters for weapons that are used in all areas of armed forces. Results are based on experimental methods assessing the extraction forces from barrel after projectile loading. These tests were performed as a series of tests with consequent technical diagnostics according to the new Czech Defence Standards (derived from NATO standards). The results are presented as the new methodologies for diagnostics of 125 mm barrel 2A46 and ramming devices of tank T-72 for use by technical logistic units in the Czech Republic Armed Forces.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Infantry fighting vehicle in case of burst firing
The article deals with an attitude to the description of the vibration of combat vehicle when burst fires together with movement on the battlefield. The three degree of freedom models is presented.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Infantry fighting vehicle in case of burst firing
The article deals with an attitude to the description of the vibration of combat vehicle when burst fires together with movement on the battlefield. The three degree of freedom models is presented.