Mahesh Soni
Mahesh Soni has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Satinder Kumar Sharma
Indian Institute of Technology Mandi
12 shared publications - Ajay Soni
Indian Institute of Technology Mandi
7 shared publications - Pawan Kumar
Nanoparticles by Design Unit, Okinawa Institute of Science and Technology (OIST) Graduate University, 1919-1 Tancha, Onna-Son, Okinawa, 904-0495, Japan
6 shared publications - Ravinder Dahiya
Northeastern University
4 shared publications - Adesh Kumar Saini
Department of Bio-Sciences and Technology, Maharishi Markandeshwar Engineering College, Maharishi Markandeshwar (Deemed to Be University), Mullana, Ambala-133207, India
3 shared publications Divya Mittal
3 shared publications
Latest Publications
- 20 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 20 (3) , 570-575
NrGO Floating Gate/SiOXNY Tunneling Layer Stack for Nonvolatile Flash Memory Applications
This paper presents an ultra.thin silicon oxynitride (SiOXNY, 4 nm) tunneling layer, nitrogen functionalized reduced graphene oxide (NrGO, 3.5 layer) floating gate (FG) and poly (methyl methacrylate) (PMMA, 60 nm) blocking layers based Al/PMMA/NrGO/SiOXNY/p.Si/Au, non.volatile flash memory (NVFM) structures. The ultra.thin SiOXNY helps in improving the interface with Si, resulting in lower gate leakage current density and considerable enhanced retention characteristics. The nitrogen engineered GO followed by reduction to NrGO under UV illumination attributes to the modification of the physiochemical properties, hence beneficial for non-volatile memory applications. The uniform, stress free and low temperature processing advocates the potential of PMMA as blocking layer for improved memory characteristics. The electrical characterizations on the fabricated Al/PMMA/NrGO/SiOXNY/p.Si/Au gate stack demonstrates a memory window (δW) of 1.25 V @ ± 3 V and 2.6 V @ ± 5 V, low gate leakage current density (J) 10 nA/cm2 @ -1 V, retention 3 1011 sec (> 10 years with extrapolation) and endurance of more than 100 cycles.
- 20 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 20 (3) , 570-575
NrGO Floating Gate/SiOXNY Tunneling Layer Stack for Nonvolatile Flash Memory Applications
This paper presents an ultra.thin silicon oxynitride (SiOXNY, 4 nm) tunneling layer, nitrogen functionalized reduced graphene oxide (NrGO, 3.5 layer) floating gate (FG) and poly (methyl methacrylate) (PMMA, 60 nm) blocking layers based Al/PMMA/NrGO/SiOXNY/p.Si/Au, non.volatile flash memory (NVFM) structures. The ultra.thin SiOXNY helps in improving the interface with Si, resulting in lower gate leakage current density and considerable enhanced retention characteristics. The nitrogen engineered GO followed by reduction to NrGO under UV illumination attributes to the modification of the physiochemical properties, hence beneficial for non-volatile memory applications. The uniform, stress free and low temperature processing advocates the potential of PMMA as blocking layer for improved memory characteristics. The electrical characterizations on the fabricated Al/PMMA/NrGO/SiOXNY/p.Si/Au gate stack demonstrates a memory window (δW) of 1.25 V @ ± 3 V and 2.6 V @ ± 5 V, low gate leakage current density (J) 10 nA/cm2 @ -1 V, retention 3 1011 sec (> 10 years with extrapolation) and endurance of more than 100 cycles.
- Open Access
- 14 July 2020
- Published by Wiley in Advanced Electronic Materials
- Vol. 6 (8)
PEDOT:PSS Microchannel‐Based Highly Sensitive Stretchable Strain Sensor
This paper presents poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate polymer microchannel (diameter ≈175 µm) based stretchable strain sensor developed inside polydimethylsiloxane substrate. The microchannel diameter changes when subjected to various strains, leading to change in the resistance of strain sensor. The sensor exhibits about three order (ΔR/R0 ≈ 1200) increase in the resistance (R) for 10% applied strain (ΔL/L, L = length of the sensor). This leads to a gauge factor (GF Δ (ΔR/R0)/(ΔL/L) of ≈12 000, which is about ≈400 times higher than most of the reported polymer‐based strain sensors. The sensor is evaluated up to a maximum strain of 30%, which is the standard strain limit associated with human body parts such as fingers and wrists. The sensor exhibits a considerably good average degree of hysteresis (R/R0 ≈ 250) and (ΔR/R0 ≈ 300) is recorded for 90° bending and 150° twisting, respectively. The sensor shows an electrical resolution of ≈150% per degree of free bending and ≈12k% per percentage of stretching. Finally, the potential application of presented sensor in robotics and wearable systems is demonstrated by using sensor feedback from human hand to remotely control the robotic hand movements.
- 14 July 2020
- Published by Wiley in Advanced Electronic Materials
- Vol. 6 (8)
Open AccessPEDOT:PSS Microchannel‐Based Highly Sensitive Stretchable Strain Sensor
This paper presents poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate polymer microchannel (diameter ≈175 µm) based stretchable strain sensor developed inside polydimethylsiloxane substrate. The microchannel diameter changes when subjected to various strains, leading to change in the resistance of strain sensor. The sensor exhibits about three order (ΔR/R0 ≈ 1200) increase in the resistance (R) for 10% applied strain (ΔL/L, L = length of the sensor). This leads to a gauge factor (GF Δ (ΔR/R0)/(ΔL/L) of ≈12 000, which is about ≈400 times higher than most of the reported polymer‐based strain sensors. The sensor is evaluated up to a maximum strain of 30%, which is the standard strain limit associated with human body parts such as fingers and wrists. The sensor exhibits a considerably good average degree of hysteresis (R/R0 ≈ 250) and (ΔR/R0 ≈ 300) is recorded for 90° bending and 150° twisting, respectively. The sensor shows an electrical resolution of ≈150% per degree of free bending and ≈12k% per percentage of stretching. Finally, the potential application of presented sensor in robotics and wearable systems is demonstrated by using sensor feedback from human hand to remotely control the robotic hand movements.
- Open Access
- 1 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
High Performance Printed Electronics on Large Area Flexible Substrates
Printed electronics has attracted significant interest in recent years due to simple, cost-effective fabrication, reduced e-waste and potential for the development of multifunctional devices over large areas. Over the years, various printing technologies have been developed to pattern flexible surfaces to develop wide range of electronic devices. A large part of the research so far has focussed on organic semiconductors based devices, even if the modest performance they offer is insufficient for several emerging applications (e. g. internet of things (IoTs), smart cities, robotics, etc.) where fast computation and communication are required. The high-performance requirements could be addressed with printed devices from high-mobility materials such as single crystal silicon (Si) and graphene. This paper presents the printing methodologies (i.e. contact and transfer printing) that are being explored for highperformance devices and circuits using nano to macro scale structures such as semiconductor nanowires (NWs), nanoribbon (NR), and ultra-thin chips (UTCs) as well as graphene. Few examples of high-performance devices obtained using contact and transfer printing are also presented.
- 1 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Open AccessHigh Performance Printed Electronics on Large Area Flexible Substrates
Printed electronics has attracted significant interest in recent years due to simple, cost-effective fabrication, reduced e-waste and potential for the development of multifunctional devices over large areas. Over the years, various printing technologies have been developed to pattern flexible surfaces to develop wide range of electronic devices. A large part of the research so far has focussed on organic semiconductors based devices, even if the modest performance they offer is insufficient for several emerging applications (e. g. internet of things (IoTs), smart cities, robotics, etc.) where fast computation and communication are required. The high-performance requirements could be addressed with printed devices from high-mobility materials such as single crystal silicon (Si) and graphene. This paper presents the printing methodologies (i.e. contact and transfer printing) that are being explored for highperformance devices and circuits using nano to macro scale structures such as semiconductor nanowires (NWs), nanoribbon (NR), and ultra-thin chips (UTCs) as well as graphene. Few examples of high-performance devices obtained using contact and transfer printing are also presented.
- Open Access
- 30 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 20 (14) , 7525-7531
Printed Temperature Sensor Based on PEDOT: PSS-Graphene Oxide Composite
Temperature sensing is an important parameter needed to be measured by the eSkin during the physical interaction of robots with real-world objects. Yet, most of the work on sensors in eSkin has focused on pressure sensing. Here we present a skin conformable printed temperature sensor with poly(3,4-ethylenedioxythiophene): poly (styrenesulfonate) (PEDOT:PSS)-graphene oxide (GO) as a temperature sensitive layer and silver (Ag) as contact electrodes. The demonstration of PEDOT:PSS/GO as a highly temperature sensitive layer is the distinct feature of the work. The response of presented sensor observed over ~25 °C (room temperature (RT)) to 100 °C, by measuring the variation in resistance across the GO/PEDOT:PSS layer showed ~80% decrease in resistance. The sensitivity of the sensor was found to be 1.09% per °C. The sensor’s response was also observed under static and dynamic bending (for 1000 cycles) conditions. The stable and repeatable response of sensor, in both cases, signifies strong adhesion of the layers with negligible delamination or debonding. In comparison to the commercial thermistor, the printed GO/PEDOT:PSS sensor is faster ( ~73% superior) with response and recovery times of 18 s and 32 s respectively. Finally, the sensor was attached to a robotic hand to allow the robot to act by using temperature feedback.
- 30 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 20 (14) , 7525-7531
Open AccessPrinted Temperature Sensor Based on PEDOT: PSS-Graphene Oxide Composite
Temperature sensing is an important parameter needed to be measured by the eSkin during the physical interaction of robots with real-world objects. Yet, most of the work on sensors in eSkin has focused on pressure sensing. Here we present a skin conformable printed temperature sensor with poly(3,4-ethylenedioxythiophene): poly (styrenesulfonate) (PEDOT:PSS)-graphene oxide (GO) as a temperature sensitive layer and silver (Ag) as contact electrodes. The demonstration of PEDOT:PSS/GO as a highly temperature sensitive layer is the distinct feature of the work. The response of presented sensor observed over ~25 °C (room temperature (RT)) to 100 °C, by measuring the variation in resistance across the GO/PEDOT:PSS layer showed ~80% decrease in resistance. The sensitivity of the sensor was found to be 1.09% per °C. The sensor’s response was also observed under static and dynamic bending (for 1000 cycles) conditions. The stable and repeatable response of sensor, in both cases, signifies strong adhesion of the layers with negligible delamination or debonding. In comparison to the commercial thermistor, the printed GO/PEDOT:PSS sensor is faster ( ~73% superior) with response and recovery times of 18 s and 32 s respectively. Finally, the sensor was attached to a robotic hand to allow the robot to act by using temperature feedback.
- 23 December 2019
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 378 (2164) , 20190156
Soft eSkin: distributed touch sensing with harmonized energy and computing
Inspired by biology, significant advances have been made in the field of electronic skin (eSkin) or tactile skin. Many of these advances have come through mimicking the morphology of human skin and by distributing few touch sensors in an area. However, the complexity of human skin goes beyond mimicking few morphological features or using few sensors. For example, embedded computing (e.g. processing of tactile data at the point of contact) is centric to the human skin as some neuroscience studies show. Likewise, distributed cell or molecular energy is a key feature of human skin. The eSkin with such features, along with distributed and embedded sensors/electronics on soft substrates, is an interesting topic to explore. These features also make eSkin significantly different from conventional computing. For example, unlike conventional centralized computing enabled by miniaturized chips, the eSkin could be seen as a flexible and wearable large area computer with distributed sensors and harmonized energy. This paper discusses these advanced features in eSkin, particularly the distributed sensing harmoniously integrated with energy harvesters, storage devices and distributed computing to read and locally process the tactile sensory data. Rapid advances in neuromorphic hardware, flexible energy generation, energy-conscious electronics, flexible and printed electronics are also discussed. This article is part of the theme issue ‘Harmonizing energy-autonomous computing and intelligence’.
- 23 December 2019
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 378 (2164) , 20190156
Soft eSkin: distributed touch sensing with harmonized energy and computing
Inspired by biology, significant advances have been made in the field of electronic skin (eSkin) or tactile skin. Many of these advances have come through mimicking the morphology of human skin and by distributing few touch sensors in an area. However, the complexity of human skin goes beyond mimicking few morphological features or using few sensors. For example, embedded computing (e.g. processing of tactile data at the point of contact) is centric to the human skin as some neuroscience studies show. Likewise, distributed cell or molecular energy is a key feature of human skin. The eSkin with such features, along with distributed and embedded sensors/electronics on soft substrates, is an interesting topic to explore. These features also make eSkin significantly different from conventional computing. For example, unlike conventional centralized computing enabled by miniaturized chips, the eSkin could be seen as a flexible and wearable large area computer with distributed sensors and harmonized energy. This paper discusses these advanced features in eSkin, particularly the distributed sensing harmoniously integrated with energy harvesters, storage devices and distributed computing to read and locally process the tactile sensory data. Rapid advances in neuromorphic hardware, flexible energy generation, energy-conscious electronics, flexible and printed electronics are also discussed. This article is part of the theme issue ‘Harmonizing energy-autonomous computing and intelligence’.
- 16 December 2019
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 31 (3) , 1986-1995
Alternate lanthanum oxide/silicon oxynitride-based gate stack performance enhancement due to ultrathin oxynitride interfacial layer for CMOS applications
- 16 December 2019
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 31 (3) , 1986-1995
Alternate lanthanum oxide/silicon oxynitride-based gate stack performance enhancement due to ultrathin oxynitride interfacial layer for CMOS applications
- 12 October 2019
- Published by Springer Nature
- p. 277-297
Emerging Techniques and Materials for Water Pollutants Detection
- 12 October 2019
- Published by Springer Nature
- p. 277-297
Emerging Techniques and Materials for Water Pollutants Detection
- 17 July 2019
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 34 (8) , 085009
Low voltage & controlled switching of MoS2-GO resistive layers based ReRAM for non-volatile memory applications
Emerging information technology and data deluge foster the unprecedented demands of higher chip density, clocking speed, data storage and lower power dissipation for on-chip non-volatile memories (NVMs). Here, two types of metal-insulator-metal (MIM) based NVM structures were fabricated and demonstrated involving controlled functionalization of molybdenum disulfide (MoS 2 ) and graphene oxide (GO) nanocomposite as a resistive switching layer. The first type of device constitutes Aluminum (Al) top and bottom electrode resulting in the Al/MoS 2 -GO/Al structure. While the second type of device uses Al top electrode and Indium Tin Oxide (ITO) bottom electrode resulting in Al/MoS 2 -GO/ITO. The current-voltage (I–V) characteristics for fabricated Al/MoS 2 -GO/Al and Al/MoS 2 -GO/ITO MIM structures exhibited considerable I ON /I OFF ratio of ∼10 2 (SET and RESET state at 0.5 V and −0.4 V) and ∼10 1 (SET and RESET state at 0.3 V and −1 V), respectively. The I–V characteristics for Al/MoS 2 -GO/Al MIM structure showed low voltage switching, substantial memory retention ∼10 4 s and endurance for up to 25 cycles. The low voltage and controlled switching operation for Al/MoS 2 -GO/Al MIM structures may be attributed to the presence of a large number of oxygen vacancies, defects in MoS 2 -GO, promoting enhanced charge hopping via interfacial oxide at MoS 2 -GO/Al interface as compared to MoS 2 -GO/ITO.
- 17 July 2019
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 34 (8) , 085009
Low voltage & controlled switching of MoS2-GO resistive layers based ReRAM for non-volatile memory applications
Emerging information technology and data deluge foster the unprecedented demands of higher chip density, clocking speed, data storage and lower power dissipation for on-chip non-volatile memories (NVMs). Here, two types of metal-insulator-metal (MIM) based NVM structures were fabricated and demonstrated involving controlled functionalization of molybdenum disulfide (MoS 2 ) and graphene oxide (GO) nanocomposite as a resistive switching layer. The first type of device constitutes Aluminum (Al) top and bottom electrode resulting in the Al/MoS 2 -GO/Al structure. While the second type of device uses Al top electrode and Indium Tin Oxide (ITO) bottom electrode resulting in Al/MoS 2 -GO/ITO. The current-voltage (I–V) characteristics for fabricated Al/MoS 2 -GO/Al and Al/MoS 2 -GO/ITO MIM structures exhibited considerable I ON /I OFF ratio of ∼10 2 (SET and RESET state at 0.5 V and −0.4 V) and ∼10 1 (SET and RESET state at 0.3 V and −1 V), respectively. The I–V characteristics for Al/MoS 2 -GO/Al MIM structure showed low voltage switching, substantial memory retention ∼10 4 s and endurance for up to 25 cycles. The low voltage and controlled switching operation for Al/MoS 2 -GO/Al MIM structures may be attributed to the presence of a large number of oxygen vacancies, defects in MoS 2 -GO, promoting enhanced charge hopping via interfacial oxide at MoS 2 -GO/Al interface as compared to MoS 2 -GO/ITO.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Microchannel based Flexible Dynamic Strain Sensor
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Microchannel based Flexible Dynamic Strain Sensor