Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jiangtao Huangfu has a total of 152 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Passive Microwave Angular Sensor Based on Local Perturbation of a Split-Ring Resonator

    by Yingzhou Chen, Zihe Cheng, Minyang Wu, Jingyuan Huang, Xingyu Liu, Peiying Lin, Jiangtao Huangfu

    This work presents a microwave attitude sensing method and device based on localized perturbation of a split-ring resonator (SRR). The sensor comprises a planar SRR, parallel microstrip feed lines and a metallic disk that can move along a circular trajectory. When the sensor’s orientation is modified in a plane perpendicular to the ground, the metallic disk moves within the constrained structure under the influence of gravity and changes its position relative to the SRR, modulating the local near field and the microstrip coupling state. Consequently, variations in angle are observed across multiple S-parameter channels. The mechanism is validated through simulation and experimental measurements. The measured S-parameters are used to construct a circular residual mixture-of-experts Gaussian process regression (MoE-GPR) model, which is developed for 360° angle reconstruction. In leave-one-angle-out (LOAO) validation on data sampled at 2.5° intervals, the proposed reconstruction method achieves a mean absolute error (MAE) of 0.700°. When trained on data sampled at 10° intervals and tested on a dataset sampled at 2.5° intervals, the proposed method achieves an MAE of 1.125°, demonstrating its generalization across different angular sampling conditions. As no active electronics are required at the moving sensing element, the proposed configuration has potential for integration with RF sensing and communication platforms, as well as for inclination sensing referenced to gravity, orientation detection and structural health monitoring.

  • Open Access

    Reconfigurable RF Antenna Based on Magnetic Building Blocks

    by Zihe Cheng, Yingzhou Chen, Zhihui Wang, Wenhao Kang, Minyang Wu, Yuze Shao, Jiangtao Huangfu

    Conventional antenna designs generally have fixed configurations and are difficult to assemble rapidly and flexibly. To address this limitation, this paper proposes a magnetic antenna building block that enables the rapid assembly of functional antennas. Based on this building block design, a kind of reconfigurable frequency scanning leaky wave antenna is implemented. The antenna module consists of the RF structure, dielectric housing, and embedded magnets. Magnets align and attach adjacent modules, while RF signals are transmitted through non-contact capacitive coupling interfaces and radiated by the RF structures on individual modules. The Port module, low-radiation module L, and high-radiation module H are designed. A variable number of cascaded modules can be rapidly cascaded through magnetic attachment to form different antenna arrays. The H module incorporates a pair of symmetric circular patches connected in parallel and exhibits stronger radiation characteristics than the L module, which does not include this parallel structure. Simulation and measurement results showed that the antenna arrays achieved effective port impedance matching in the C-band for cascades of the same type of modules and several mixed cascades of different types of modules. Far-field measurements also showed that arrays with different module combinations produced distinct far-field radiation patterns and allowed adjustment of the main beam gain and direction over 6.30–6.90 GHz. The main beam direction varied over a range of approximately 30°, and continuously covered the region around normal direction. The beamwidth varied with module types and the number of cascaded modules. The 3 dB beamwidth decreased from 48° to 21°, and the highest peak gain reached 6.98 dBi. The proposed magnetic antenna building block supports module cascading, combinations of different module types, and frequency scanning, providing a low-cost and flexible implementation of reconfigurable antenna arrays for communication and sensing applications.

  • Open Access

    Localization Method for Distributed Radar Clusters with Configuration Adjustment Based on Fisher Information Matrix Prediction

    by Jiacheng Dai, Jiangtao Huangfu, Junchi Lv, Baixiang Chen, Wensheng Chang, Jun Tang

    In the localization of a distributed radar cluster under far-field and short-baseline conditions with a configuration that varies with time, traditional translational maneuvering strategies have limited capability to expand the observation angle. This makes it difficult to effectively improve the observation geometry, and can easily lead to the amplification of localization errors. Targeting this problem, this work proposes a localization method with configuration adjustment based on Fisher information matrix (FIM) prediction. Without requiring prior information of the true target position, the proposed method predicts the FIMs of candidate configurations based on the current target position estimate. It evaluates these configurations by minimizing the localization uncertainty along the worst direction, thereby enabling adaptive adjustment of the cluster configuration. Furthermore, an in-place rotational strategy is introduced to enhance angular diversity, and a Gauss–Newton iterative solution is developed by incorporating temporal prior information to improve the stability of nonlinear localization. Simulation results show that the proposed method can effectively improve the observation geometry under far-field and short-baseline conditions, and reduce abnormal jumps caused by noise. Compared with the traditional translational maneuvering strategy, the proposed method reduces the localization error by more than 70%.

  • Open Access

    SPPs Structure Touch Sensing Method with Microstrip Transmission Line

    by Jiayu Song, Zhihui Wang, Minyang Wu, Zihe Cheng, Yingzhou Chen, Xingyu Liu, Jiangtao Huangfu

    This paper proposes a microstrip touch sensing design compatible with radio frequency (RF) signal communication ability. The design is based on surface plasmon polaritons (SPPs) and employs a microstrip touch sensing structure with multiple periodic parallel open circuit branches, which is further connected in parallel with the signal transmission microstrip. The SPP structure is designed in a U-shaped structure and exhibits multiple resonance characteristics for RF signals. Its S-parameter in the low frequency band is affected by finger or medium touch, while the parallel microstrip transmission line correspondingly maintains signal transmission capability in the high frequency band, which remains unaffected. A physics-informed regression framework based on spectral alignment and Gaussian Process Regression (GPR) is introduced for the analysis of both simulation and experimental results. Based on the spectral-position relationship, touch position detection with an accuracy of within 5 mm is achieved by monitoring changes in the S-parameter response below 4.7 GHz. Meanwhile, a communication passband unaffected by tactile sensing is maintained within the 4.7 GHz to 6.0 GHz frequency range. This design demonstrates significant potential for applications requiring integrated sensing and communication (ISAC), including the Internet of Things and smart wearable devices.

  • A Variable-Resolution Amplitude–Frequency Response Measurement Method Based on Multimode RF Chaotic Signals

    by Xingyu Liu, Xuesong Guo, Sijie Chen, Wenhao Kang, Jiangtao Huangfu

    This article proposes and experimentally validates a variable-resolution amplitude–frequency response measurement method utilizing multimode radio frequency (RF) chaotic signals. Based on the compressive sensing (CS) theory, this method employs multimode RF chaotic signals to achieve compressed sampling and greedy iterative reconstruction of the response of the device under test (DUT). The key innovation lies in generating multimode RF chaotic signals by mixing a fundamental RF chaotic signal with single-tone RF signals. Meanwhile, a fusion reconstruction algorithm is proposed to improve measurement accuracy. Leveraging the broadband continuous spectrum of chaotic signals, the method achieves variable-resolution reconstruction within a single measurement. Experimental results demonstrate a 0.6–3.0-GHz measurement system reconstructing 101-point responses from 50 samples with a 2.02 compression ratio. Numerical simulations and physical experiments on 0.915-and 1.890-GHz bandpass filters validate the fusion algorithm’s capability for global reconstruction (24-MHz resolution) and local reconstruction (8-MHz resolution). Compared with conventional single-tone scanning methods, the proposed method reduces sampling operations by 50.5% while maintaining low hardware complexity. Unlike low-resolution global scanning that may miss narrowband targets, this method ensures detection reliability while enabling variable-resolution ability in a single measurement. The proposed method shows potential for electromagnetic target characterization applications.

  • High-performance transparent graphene-based antennas

    by Chaoye Hong, Lusong Wei, Weijia Wang, Youmei Tang, Qinghai Zhu, Jiangtao Huangfu, Mingsheng Xu


  • Open Access

    Intelligent Gesture Recognition Based on Screen Reflectance Multi-Band Spectral Features

    by Peiying Lin, Chenrui Li, Sijie Chen, Jiangtao Huangfu, Wei Yuan

    Human–computer interaction (HCI) with screens through gestures is a pivotal method amidst the digitalization trend. In this work, a gesture recognition method is proposed that combines multi-band spectral features with spatial characteristics of screen-reflected light. Based on the method, a red-green-blue (RGB) three-channel spectral gesture recognition system has been developed, composed of a display screen integrated with narrowband spectral receivers as the hardware setup. During system operation, emitted light from the screen is reflected by gestures and received by the narrowband spectral receivers. These receivers at various locations are tasked with capturing multiple narrowband spectra and converting them into light-intensity series. The availability of multi-narrowband spectral data integrates multidimensional features from frequency and spatial domains, enhancing classification capabilities. Based on the RGB three-channel spectral features, this work formulates an RGB multi-channel convolutional neural network long short-term memory (CNN-LSTM) gesture recognition model. It achieves accuracies of 99.93% in darkness and 99.89% in illuminated conditions. This indicates the system’s capability for stable operation across different lighting conditions and accurate interaction. The intelligent gesture recognition method can be widely applied for interactive purposes on various screens such as computers and mobile phones, facilitating more convenient and precise HCI.


  • Assembling Reconfigurable Intelligent Metasurfaces With a Synthetic Neural Network

    by Pujing Lin, Chao Qian, Yuetian Jia, Zhedong Wang, Bei Wu, Jiangtao Huangfu, Hongsheng Chen

    Reconfigurable metasurfaces have provided us with extraordinary ways to manipulate electromagnetic waves at sub-wavelength scale and taught us how to implement various tasks in a wide range. As its next generation, intelligent metasurfaces have recently attracted much attention as they are endowed with intelligence to self-adapt to ever-changing environment. So far, although there are a number of works about the creation of deep learning algorithms to drive intelligent metasurfaces, they are mostly about fixed objects and thus constrained by specific applications. In this work, we propose a synthetic neural network to break the limit that conventional inverse design algorithms only work for certain metasurface configuration. The dynamic assembly of reconfigurable metasurfaces in physical space is directly mapped to the network recombination in algorithm space. This is particularly useful because it can greatly save training data and avoid repeated training of network. We apply it in the inverse design of metasurfaces with the relative error less than 13%, and experimentally demonstrate reconfigurable microwave metasurfaces with flexible deployment. Our work opens up a promising avenue for overcoming the application-bound limitations of conventional inverse designs, particularly in the dynamic and adaptive context of intelligent metasurfaces.


  • Microwave Imaging Method Based on Reconfigurable Spatial Dispersion Radiation

    by Yuting Wu, Hongbin Ma, Yinger Zhang, Qian Zhang, Zhouyi Wu, Jiangtao Huangfu

    Based on a reconfigurable spatial dispersive radiation antenna, a microwave compressive sensing imaging method is proposed in this article. According to theoretical analysis, it cannot improve lateral resolution without reducing range resolution in a traditional dispersion-based microwave imaging system. In this work, the issue is addressed by the proposed tunable traveling wave antenna (T-TWA) and variable spatial dispersion compressed sensing (CS) imaging. The T-TWA realizes mechanical, spatial dispersion radiation reconfiguration within the 6.5–10.5 GHz frequency band while maintaining the radiation surface position fixed. Then, the CS algorithm is applied to implement 2-D imaging and positioning on a 5 mm side length target. Simulation and experiment demonstrate that the proposed system attains a lateral resolution of 2 mm (about 1/20 central wavelength) and a range resolution of 7 mm (about 1/5 central wavelength), exhibiting a tenfold and a fivefold enhancement compared to theoretical, respectively. Compared with the imaging system based on a nonadjustable dispersion antenna, the imaging resolution is improved by more than twice in the lateral direction. The proposed imaging system and the tunable dispersive antenna are applicable in fields like vehicle radar, indoor electromagnetic positioning, etc.


  • A tunable water antenna

    by Yuting Wu, Peiying Lin, Zhouyi Wu, Xingyu Liu, Jiangtao Huangfu

    This paper presents a pure water antenna with frequency reconfigurability, which is composed of a water resonator, L‐shaped feeder, and metal ground pad. An L‐shaped feeding structure is designed so that the working frequency can be adjusted by changing the water level of the resonator. The cross‐stack periodic water radiator structure improves the radiation efficiency by 2–4 dB compared with simple rectangular structure. The working frequency of this antenna is around 1 GHz, and will decrease by 17 MHz for every 5 mm increase in water level, which proves the feasibility of this antenna for water level monitoring. It has the potential for application in the field of wireless environmental monitoring for the Internet of Things.