Michael Wawire
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Michael Wawire has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
Daniel Sila
Dept. of Food Science and Technology, Faculty of Agriculture, Jomo Kenyatta Univ. of Agriculture and Technology, P.O. Box 62000, Nairobi 00200, Kenya
3 shared publicationsDouglas Shitanda
The Co-operative Univ. College of Kenya, P.O. Box 24814-502, Karen Nairobi, Kenya
3 shared publications- Indrawati Oey
Department of Food Science University of Otago Dunedin New Zealand
3 shared publications - Marc Hendrickx
Laboratory of Food Technology, Department of Microbial and Molecular Systems, KU Leuven, Kasteelpark Arenberg 22, B-3001 Leuven, Belgium
3 shared publications Charles K. Njoroge
Dept. of Food Science and Technology, Faculty of Agriculture, Jomo-Kenyatta Univ. of Agriculture and Technology, P.O. Box 62000, Nairobi, 00200, Kenya
2 shared publications- Edward Dintwa
Laboratory for Agro Machinery and Processing, Catholic University Leuven, Kasteelpark Arenberg 30, B-3001 Leuven, Belgium
2 shared publications
Latest Publications
- Open Access
- 6 March 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (5) , 2351
Commentary: Iconoclastic Reflections on the ‘Safety’ of Polyunsaturated Fatty Acid-Rich Culinary Frying Oils: Some Cautions regarding the Laboratory Analysis and Dietary Ingestion of Lipid Oxidation Product Toxins
Continuous or frequent ingestion of fried foods containing cytotoxic/mutagenic/genotoxic lipid oxidation products (LOPs) may present significant human health risks; such toxins are generated in thermally stressed polyunsaturated fatty acid (PUFA)-rich culinary frying oils (CFOs) during standard frying practices. Since monounsaturated and saturated fatty acids (MUFAs and SFAs, respectively) are much less susceptible to peroxidation than PUFAs, in this study CFOs of differential unsaturated fatty acid contents were exposed to laboratory-simulated shallow-frying episodes (LSSFEs). Firstly, we present a case study exploring the time-dependent generation of aldehydic LOPs in CFO products undergoing LSSFEs, which was then used to evaluate the relative potential health risks posed by them, and also to provide suitable recommendations concerning their safety when used for frying purposes. Sunflower, rapeseed, extra-virgin olive and coconut oils underwent LSSFEs at 180 °C: Samples were collected at 0–90 min time-points (n = 6 replicates per oil). Aldehydes therein were determined by high-resolution 1H NMR analysis at 400 and 600 MHz operating frequencies. For one of the first times, CFO LOP analysis was also performed on a non-stationary 60 MHz benchtop NMR spectrometer. 1H NMR analysis confirmed the thermally promoted, time-dependent production of a wide range of aldehydic LOPs in CFOs. As expected, the highest levels of these toxins were produced in PUFA-rich sunflower oil, with lower concentrations formed in MUFA-rich canola and extra-virgin olive oils; in view of its very high SFA content, only very low levels of selected aldehyde classes were generated in coconut oil during LSSFEs. Secondly, 1H NMR results acquired are discussed with regard to the suitability and validity of alternative, albeit routinely employed, spectrophotometric methods for evaluating the peroxidation status of CFOs and lipid-containing foods. Thirdly, an updated mini-review of the toxicological properties of and intake limits for LOPs, and deleterious health effects posed by their ingestion, is provided. In conclusion, exposure of PUFA-rich CFOs to high-temperature frying practices generates very high concentrations of aldehydic LOP toxins from thermally promoted, O2-powered, recycling peroxidation processes; these toxins penetrate into and hence are ‘carried’ by fried foods available for human consumption. Such toxins have the capacity to contribute towards the development and progression of non-communicable chronic diseases (NCDs) if cumulatively ingested by humans.
- 6 March 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (5) , 2351
Open AccessCommentary: Iconoclastic Reflections on the ‘Safety’ of Polyunsaturated Fatty Acid-Rich Culinary Frying Oils: Some Cautions regarding the Laboratory Analysis and Dietary Ingestion of Lipid Oxidation Product Toxins
Continuous or frequent ingestion of fried foods containing cytotoxic/mutagenic/genotoxic lipid oxidation products (LOPs) may present significant human health risks; such toxins are generated in thermally stressed polyunsaturated fatty acid (PUFA)-rich culinary frying oils (CFOs) during standard frying practices. Since monounsaturated and saturated fatty acids (MUFAs and SFAs, respectively) are much less susceptible to peroxidation than PUFAs, in this study CFOs of differential unsaturated fatty acid contents were exposed to laboratory-simulated shallow-frying episodes (LSSFEs). Firstly, we present a case study exploring the time-dependent generation of aldehydic LOPs in CFO products undergoing LSSFEs, which was then used to evaluate the relative potential health risks posed by them, and also to provide suitable recommendations concerning their safety when used for frying purposes. Sunflower, rapeseed, extra-virgin olive and coconut oils underwent LSSFEs at 180 °C: Samples were collected at 0–90 min time-points (n = 6 replicates per oil). Aldehydes therein were determined by high-resolution 1H NMR analysis at 400 and 600 MHz operating frequencies. For one of the first times, CFO LOP analysis was also performed on a non-stationary 60 MHz benchtop NMR spectrometer. 1H NMR analysis confirmed the thermally promoted, time-dependent production of a wide range of aldehydic LOPs in CFOs. As expected, the highest levels of these toxins were produced in PUFA-rich sunflower oil, with lower concentrations formed in MUFA-rich canola and extra-virgin olive oils; in view of its very high SFA content, only very low levels of selected aldehyde classes were generated in coconut oil during LSSFEs. Secondly, 1H NMR results acquired are discussed with regard to the suitability and validity of alternative, albeit routinely employed, spectrophotometric methods for evaluating the peroxidation status of CFOs and lipid-containing foods. Thirdly, an updated mini-review of the toxicological properties of and intake limits for LOPs, and deleterious health effects posed by their ingestion, is provided. In conclusion, exposure of PUFA-rich CFOs to high-temperature frying practices generates very high concentrations of aldehydic LOP toxins from thermally promoted, O2-powered, recycling peroxidation processes; these toxins penetrate into and hence are ‘carried’ by fried foods available for human consumption. Such toxins have the capacity to contribute towards the development and progression of non-communicable chronic diseases (NCDs) if cumulatively ingested by humans.
- Open Access
- 1 January 2021
- Published by Taylor & Francis in International Journal of Food Properties
- Vol. 24 (1) , 517-532
Insolubility and denaturation of whey proteins of skimmed camel milk as affected by spray drying operating parameters
The effect of spray drying process parameters (i.e., inlet temperature, atomization pressure, and feed flow rate) on the denaturation of whey proteins of skimmed camel milk was studied using a face-centered central composite design. Spray drying of skimmed camel milk (i.e., total solids of 8.4% [w/w]) produced powders with a total solids content of 94–97% (w/w), protein 22–29% (w/w) and lactose 27–31% (w/w). The process was optimized using response surface methodology in combination with desirability function. A maximum recovery of 61% of the total solids was achieved while still maintaining denaturation of whey protein and insolubility index levels at their minimum possible value of 39% and 0.1 mL, respectively. The final moisture content of the powder at these conditions was 3.3% (w/w). This implies that, as denaturation was the primary mechanism by which camel milk lose its protective proteins, minimizing denaturation would make it possible to produce skimmed camel milk powders with good nutritional and therapeutic values. The morphology of spray-dried skimmed camel milk processed at 140°C showed greater spherical intact particles than their cow milk powder counterparts.
- 1 January 2021
- Published by Taylor & Francis in International Journal of Food Properties
- Vol. 24 (1) , 517-532
Open AccessInsolubility and denaturation of whey proteins of skimmed camel milk as affected by spray drying operating parameters
The effect of spray drying process parameters (i.e., inlet temperature, atomization pressure, and feed flow rate) on the denaturation of whey proteins of skimmed camel milk was studied using a face-centered central composite design. Spray drying of skimmed camel milk (i.e., total solids of 8.4% [w/w]) produced powders with a total solids content of 94–97% (w/w), protein 22–29% (w/w) and lactose 27–31% (w/w). The process was optimized using response surface methodology in combination with desirability function. A maximum recovery of 61% of the total solids was achieved while still maintaining denaturation of whey protein and insolubility index levels at their minimum possible value of 39% and 0.1 mL, respectively. The final moisture content of the powder at these conditions was 3.3% (w/w). This implies that, as denaturation was the primary mechanism by which camel milk lose its protective proteins, minimizing denaturation would make it possible to produce skimmed camel milk powders with good nutritional and therapeutic values. The morphology of spray-dried skimmed camel milk processed at 140°C showed greater spherical intact particles than their cow milk powder counterparts.
- Open Access
- 16 September 2020
- Published by Wiley in Journal of Food Science
- Vol. 85 (10) , 3459-3466
Comparison of the viscosity of camel milk with model milk systems in relation to their atomization properties
To correlate the viscosity of camel milk with its atomization properties, first, the viscosity profiles of camel milk are compared with model milk systems (reconstituted skimmed cow milk powder). Then, atomization experiment was conducted using model milk systems and finally, the findings of the atomization experiments were coincided with the viscosity profiles. The effect of total solids of whole (10% to 40%) and skimmed (7.5% to 30%) camel milks on its viscosity was investigated. At 30% total solids level and a temperature of 20 °C, skimmed camel milk exhibited a viscosity of 7.68 mPa.s whereas whole camel milk 8.96 mPa.s. This value is small compared to suspension of reconstituted skimmed cow milk powder, which reached up to 18.55 mPa.s and to that of suspension of whey protein concentrate (28.15 mPa.s). By raising the total solid from 20% to 30%, it was shown that, the average spray droplet size would be changed from 18.77 to 29.40 µm and the span from 1.76 to 1.55. Based on their viscosity profiles, these values would be obtained for camel milk at total solid values of 35% for whole and 38% for skimmed milks. This would allow camel milk to be concentrated to higher total solid levels than bovine milk. Practical Application: Converting camel milk into powder by spray drying will have a great role in its commercialization. To do so, establishing knowledge on the viscosity of camel milk at different total solids levels in relation to its atomization properties would be of paramount importance. Because, this would enable us to fine tune the viscosity of the milk to arrive at a quality powder with all the desired techno‐functional properties. Moreover, it will also contribute by furnishing engineering data pertinent to the development, design, or choice of appropriate nozzles for atomization of the milk during spray drying at different drying set ups.
- 16 September 2020
- Published by Wiley in Journal of Food Science
- Vol. 85 (10) , 3459-3466
Open AccessComparison of the viscosity of camel milk with model milk systems in relation to their atomization properties
To correlate the viscosity of camel milk with its atomization properties, first, the viscosity profiles of camel milk are compared with model milk systems (reconstituted skimmed cow milk powder). Then, atomization experiment was conducted using model milk systems and finally, the findings of the atomization experiments were coincided with the viscosity profiles. The effect of total solids of whole (10% to 40%) and skimmed (7.5% to 30%) camel milks on its viscosity was investigated. At 30% total solids level and a temperature of 20 °C, skimmed camel milk exhibited a viscosity of 7.68 mPa.s whereas whole camel milk 8.96 mPa.s. This value is small compared to suspension of reconstituted skimmed cow milk powder, which reached up to 18.55 mPa.s and to that of suspension of whey protein concentrate (28.15 mPa.s). By raising the total solid from 20% to 30%, it was shown that, the average spray droplet size would be changed from 18.77 to 29.40 µm and the span from 1.76 to 1.55. Based on their viscosity profiles, these values would be obtained for camel milk at total solid values of 35% for whole and 38% for skimmed milks. This would allow camel milk to be concentrated to higher total solid levels than bovine milk. Practical Application: Converting camel milk into powder by spray drying will have a great role in its commercialization. To do so, establishing knowledge on the viscosity of camel milk at different total solids levels in relation to its atomization properties would be of paramount importance. Because, this would enable us to fine tune the viscosity of the milk to arrive at a quality powder with all the desired techno‐functional properties. Moreover, it will also contribute by furnishing engineering data pertinent to the development, design, or choice of appropriate nozzles for atomization of the milk during spray drying at different drying set ups.
- 15 November 2018
- Published by Wiley in Journal of Food Science
- Vol. 83 (12) , 2983-2991
The Effect of Pretreatment (Spray Drying) on the Yield and Selected Nutritional Components of Whole Camel Milk Powder
The effect of spray drying on the composition of camel milk powder was evaluated. A full factorial experimental design was used to see the effects of inlet temperature (160 °C, 140 °C, and 120 °C), atomization pressure (800, 600, and 400 bar) and feed flow rate (5, 4, and 3 rev/s) on cyclone and vitamin C recoveries. Principal components analysis (PCA) was used to check classification of spray dried whole camel milk powders based on their processing conditions and multiple correspondence analysis (MCA) on the fatty acid profiles. The average proximate composition of the camel milk viz., fat, protein, lactose, and total solid were 3.0%, 3.21%, 3.01%, and 10.29% respectively. The powder yield (cyclone recovery) increased with increasing inlet temperature and decreasing feed flow rate. High outlet temperature and pressure decreased vitamin C recovery. As a result of PCA of the camel milk powders, they were classified into high heat treated and low heat treated milk powders while the MCA of the fatty acid profiles of camel milk powders were classified into high pressure and low pressure treated powders and it was concluded that higher atomization pressure caused increase in the content of fatty acids. Practical Application: Drying of camel milk (using spray drying) can extend its shelf life. The spray drying process must be optimized in order to retain the nutritional properties of the milk and the techno‐functional characteristics of the powder. Here, the effect of the spray drying conditions on the yield and selected nutritional components of the milk powder was studied using a bench top spray dryer. However, there is need to translate these findings to an industrial volume dryer. These findings will play a big role in future spray drying operations since retention of important nutritional components is an important part of food processing.
- 15 November 2018
- Published by Wiley in Journal of Food Science
- Vol. 83 (12) , 2983-2991
The Effect of Pretreatment (Spray Drying) on the Yield and Selected Nutritional Components of Whole Camel Milk Powder
The effect of spray drying on the composition of camel milk powder was evaluated. A full factorial experimental design was used to see the effects of inlet temperature (160 °C, 140 °C, and 120 °C), atomization pressure (800, 600, and 400 bar) and feed flow rate (5, 4, and 3 rev/s) on cyclone and vitamin C recoveries. Principal components analysis (PCA) was used to check classification of spray dried whole camel milk powders based on their processing conditions and multiple correspondence analysis (MCA) on the fatty acid profiles. The average proximate composition of the camel milk viz., fat, protein, lactose, and total solid were 3.0%, 3.21%, 3.01%, and 10.29% respectively. The powder yield (cyclone recovery) increased with increasing inlet temperature and decreasing feed flow rate. High outlet temperature and pressure decreased vitamin C recovery. As a result of PCA of the camel milk powders, they were classified into high heat treated and low heat treated milk powders while the MCA of the fatty acid profiles of camel milk powders were classified into high pressure and low pressure treated powders and it was concluded that higher atomization pressure caused increase in the content of fatty acids. Practical Application: Drying of camel milk (using spray drying) can extend its shelf life. The spray drying process must be optimized in order to retain the nutritional properties of the milk and the techno‐functional characteristics of the powder. Here, the effect of the spray drying conditions on the yield and selected nutritional components of the milk powder was studied using a bench top spray dryer. However, there is need to translate these findings to an industrial volume dryer. These findings will play a big role in future spray drying operations since retention of important nutritional components is an important part of food processing.
- 1 November 2018
- Published by Elsevier in Food and Bioproducts Processing
- Vol. 112, 137-149
Effect of operating parameters on the surface and physico-chemical properties of spray-dried camel milk powders
- 1 November 2018
- Published by Elsevier in Food and Bioproducts Processing
- Vol. 112, 137-149
Effect of operating parameters on the surface and physico-chemical properties of spray-dried camel milk powders
- 7 December 2015
- Published by Wiley in Journal of Food Science
- Vol. 81 (1) , E56-64
Kinetics of Thermal Inactivation of Peroxidase and Color Degradation of African Cowpea ( Vigna unguiculata ) Leaves
Cowpea leaves form an important part of the diet for many Kenyans, and they are normally consumed after a lengthy cooking process leading to the inactivation of peroxidase (POD) that could be used as an indicator for the potential shelf life of the vegetables. However, color degradation can simultaneously occur, leading to poor consumer acceptance of the product. The kinetics of POD in situ thermal (for thermal treatments in the range of 75 to 100 °C/120 min) inactivation showed a biphasic first‐order model, with Arrhenius temperature dependence of the rate constant. The kinetic parameters using a reference temperature ( T ref ) of 80 °C were determined for both the heat‐labile phase ( k ref = 11.52 ± 0.95 × 10 −2 min −1 and E a of 109.67 ± 6.20 kJ/mol) and the heat‐stable isoenzyme fraction ( k ref = 0.29 ± 0.07 × 10 −2 min −1 and E a of 256.93 ± 15.27 kJ/mol). Color degradation (L*, a*, and b* value) during thermal treatment was investigated, in particular as the “a*” value (the value of green color). Thermal degradation (thermal treatments between 55 and 80 °C per 90 min) of the green color of the leaves followed a fractional conversion model and the temperature dependence of the inactivation rate constant can be described using the Arrhenius law. The kinetic parameters using a reference temperature ( T refC = 70 °C) were determined as k refC = 13.53 ± 0.01 × 10 −2 min −1 and E aC = 88.78 ± 3.21 kJ/mol. The results indicate that severe inactivation of POD (as an indicator for improved shelf life of the cooked vegetables) is accompanied by severe color degradation and that conventional cooking methods (typically 10 min/100 °C) lead to a high residual POD activity suggesting a limited shelf life of the cooked vegetables.
- 7 December 2015
- Published by Wiley in Journal of Food Science
- Vol. 81 (1) , E56-64
Kinetics of Thermal Inactivation of Peroxidase and Color Degradation of African Cowpea ( Vigna unguiculata ) Leaves
Cowpea leaves form an important part of the diet for many Kenyans, and they are normally consumed after a lengthy cooking process leading to the inactivation of peroxidase (POD) that could be used as an indicator for the potential shelf life of the vegetables. However, color degradation can simultaneously occur, leading to poor consumer acceptance of the product. The kinetics of POD in situ thermal (for thermal treatments in the range of 75 to 100 °C/120 min) inactivation showed a biphasic first‐order model, with Arrhenius temperature dependence of the rate constant. The kinetic parameters using a reference temperature ( T ref ) of 80 °C were determined for both the heat‐labile phase ( k ref = 11.52 ± 0.95 × 10 −2 min −1 and E a of 109.67 ± 6.20 kJ/mol) and the heat‐stable isoenzyme fraction ( k ref = 0.29 ± 0.07 × 10 −2 min −1 and E a of 256.93 ± 15.27 kJ/mol). Color degradation (L*, a*, and b* value) during thermal treatment was investigated, in particular as the “a*” value (the value of green color). Thermal degradation (thermal treatments between 55 and 80 °C per 90 min) of the green color of the leaves followed a fractional conversion model and the temperature dependence of the inactivation rate constant can be described using the Arrhenius law. The kinetic parameters using a reference temperature ( T refC = 70 °C) were determined as k refC = 13.53 ± 0.01 × 10 −2 min −1 and E aC = 88.78 ± 3.21 kJ/mol. The results indicate that severe inactivation of POD (as an indicator for improved shelf life of the cooked vegetables) is accompanied by severe color degradation and that conventional cooking methods (typically 10 min/100 °C) lead to a high residual POD activity suggesting a limited shelf life of the cooked vegetables.
- 1 March 2012
- Published by Elsevier in Journal of Food Composition and Analysis
- Vol. 25 (2) , 160-165
Effect of harvest age and thermal processing on poly-γ-glutamate folates and minerals in African cowpea leaves (Vigna unguiculata)
- 1 March 2012
- Published by Elsevier in Journal of Food Composition and Analysis
- Vol. 25 (2) , 160-165
Effect of harvest age and thermal processing on poly-γ-glutamate folates and minerals in African cowpea leaves (Vigna unguiculata)
- 10 February 2011
- Published by American Chemical Society (ACS) in Journal of Agricultural and Food Chemistry
- Vol. 59 (5) , 1774-1783
Thermal Stability of Ascorbic Acid and Ascorbic Acid Oxidase in African Cowpea Leaves (Vigna unguiculata) of Different Maturities
Cowpea, an African leafy vegetable (Vigna unguiculata), contains a high level of vitamin C. The leaves harvested at 4−9 weeks are highly prone to vitamin C losses during handling and processing. Therefore, the purpose of this research was to study the effect of thermal treatment on the stability of ascorbic acid oxidase (AAO), total vitamin C content (l-ascorbic acid, l-AA), and dehydroascorbic acid (DHAA) and l-AA/DHAA ratio in cowpea leaves harvested at different maturities (4, 6, and 8 weeks old). The results showed that AAO activity, total vitamin C content, and l-AA/DHAA ratio in cowpea leaves increased with increasing maturity (up to 8 weeks). Eight-week-old leaves were the best source of total vitamin C and showed a high ratio of l-AA/DHAA (4:1). Thermal inactivation of AAO followed first-order reaction kinetics. Heating at temperatures above 90 °C for short times resulted in a complete AAO inactivation, resulting in a protective effect of l-AA toward enzyme-catalyzed oxidation. Total vitamin C in young leaves (harvested at 4 and 6 weeks) was predominantly in the form of DHAA, and therefore temperature treatment at 30−90 °C for 10 min decreased the total vitamin C content, whereas total vitamin C in 8-week-old cowpea leaves was more than 80% in the form of l-AA, so that a high retention of the total vitamin C can be obtained even after heating and/or reheating (30−90 °C for 10 min) before consumption. The results indicated that the stability of total vitamin C in situ was strongly dependent on the plant maturity stage and the processing conditions applied.
- 10 February 2011
- Published by American Chemical Society (ACS) in Journal of Agricultural and Food Chemistry
- Vol. 59 (5) , 1774-1783
Thermal Stability of Ascorbic Acid and Ascorbic Acid Oxidase in African Cowpea Leaves (Vigna unguiculata) of Different Maturities
Cowpea, an African leafy vegetable (Vigna unguiculata), contains a high level of vitamin C. The leaves harvested at 4−9 weeks are highly prone to vitamin C losses during handling and processing. Therefore, the purpose of this research was to study the effect of thermal treatment on the stability of ascorbic acid oxidase (AAO), total vitamin C content (l-ascorbic acid, l-AA), and dehydroascorbic acid (DHAA) and l-AA/DHAA ratio in cowpea leaves harvested at different maturities (4, 6, and 8 weeks old). The results showed that AAO activity, total vitamin C content, and l-AA/DHAA ratio in cowpea leaves increased with increasing maturity (up to 8 weeks). Eight-week-old leaves were the best source of total vitamin C and showed a high ratio of l-AA/DHAA (4:1). Thermal inactivation of AAO followed first-order reaction kinetics. Heating at temperatures above 90 °C for short times resulted in a complete AAO inactivation, resulting in a protective effect of l-AA toward enzyme-catalyzed oxidation. Total vitamin C in young leaves (harvested at 4 and 6 weeks) was predominantly in the form of DHAA, and therefore temperature treatment at 30−90 °C for 10 min decreased the total vitamin C content, whereas total vitamin C in 8-week-old cowpea leaves was more than 80% in the form of l-AA, so that a high retention of the total vitamin C can be obtained even after heating and/or reheating (30−90 °C for 10 min) before consumption. The results indicated that the stability of total vitamin C in situ was strongly dependent on the plant maturity stage and the processing conditions applied.