Takafumi Fukushima
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Takafumi Fukushima has a total of 316 co-authors. Here are the top co-authors by number of shared publications:
- Tetsu Tanaka
Tohoku University
167 shared publications Mitsumasa Koyanagi
Global INTegration Initiative (GINTI), New Industry Creation Hatchery Center (NICHe), Tohoku University Sendai Miyagi Japan
72 shared publicationsM. Koyanagi
71 shared publicationsM. Murugesan
43 shared publicationsKang-Wook Lee
New Industry Creation Hatchery Center, Tohoku University, Sendai, Japan
31 shared publicationsHisashi Kino
Frontier Research Institute for Interdisciplinary Sciences, Tohoku University Sendai Miyagi Japan
29 shared publications
Latest Publications
- Open Access
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (10) , 2221-2229
Degradation Mechanisms in Die-to-Wafer Hybrid Bonding Governed by Surface Activation Lifetime and Moisture Evaporation
While direct placement die-to-wafer (D2W) hybrid bonding is essential for advanced packaging, its performance is often compromised by an extended storage time between surface activation and bonding. However, the underlying chemical degradation mechanisms have not been fully elucidated because of the challenge of correlating macroscopic bond strength with molecular-scale interfacial changes. Here, we introduce a comprehensive analytical approach, combining a novel, highly accurate bonding energy measurement with multi-modal surface spectroscopy. This method reveals that degradation is governed by a dual-factor mechanism: the loss of interfacial water and the depletion of surface silanol groups. The direct correlation between these interfacial changes and the reduction in bonding energy was quantitatively confirmed by thermal desorption and sum-frequency generation spectroscopy. This study provides the first quantitative insight into the degradation kinetics during storage, offering a clear scientific basis for optimizing D2W hybrid bonding processes.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (10) , 2221-2229
Open AccessDegradation Mechanisms in Die-to-Wafer Hybrid Bonding Governed by Surface Activation Lifetime and Moisture Evaporation
While direct placement die-to-wafer (D2W) hybrid bonding is essential for advanced packaging, its performance is often compromised by an extended storage time between surface activation and bonding. However, the underlying chemical degradation mechanisms have not been fully elucidated because of the challenge of correlating macroscopic bond strength with molecular-scale interfacial changes. Here, we introduce a comprehensive analytical approach, combining a novel, highly accurate bonding energy measurement with multi-modal surface spectroscopy. This method reveals that degradation is governed by a dual-factor mechanism: the loss of interfacial water and the depletion of surface silanol groups. The direct correlation between these interfacial changes and the reduction in bonding energy was quantitatively confirmed by thermal desorption and sum-frequency generation spectroscopy. This study provides the first quantitative insight into the degradation kinetics during storage, offering a clear scientific basis for optimizing D2W hybrid bonding processes.
- Open Access
- 31 August 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (16) , 16SP11
Implementation of agile die-level TSV formation and heterogeneous integration with standard multi-project wafer shuttle dies
To overcome the prohibitive costs and wafer-scale incompatibilities of conventional three-dimensional (3D) integration, we present an agile “Die-Level Via-Last” platform tailored for rapid prototyping. This approach transforms standard Multi-Project Wafer shuttle dies into 3D building blocks, enabling the heterogeneous integration of silicon logic with active compound semiconductor devices regardless of their original wafer dimensions. We detail the fabrication process, focusing on accessible through-silicon via (TSV) formation using standard magnetron sputtering to minimize infrastructure barriers. As a validation vehicle, a commercial mini-LED array is heterogeneously integrated onto a 180 nm node silicon shuttle die via room-temperature direct Cu semi-additive plating bonding. Electrical characterization confirms vertical interconnects, and the active driving of the mini-LED array is successfully demonstrated. This work establishes a viable pathway for the high-mix, low-volume manufacturing of heterogeneous 3D systems without rigid foundry constraints.
- 31 August 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (16) , 16SP11
Open AccessImplementation of agile die-level TSV formation and heterogeneous integration with standard multi-project wafer shuttle dies
To overcome the prohibitive costs and wafer-scale incompatibilities of conventional three-dimensional (3D) integration, we present an agile “Die-Level Via-Last” platform tailored for rapid prototyping. This approach transforms standard Multi-Project Wafer shuttle dies into 3D building blocks, enabling the heterogeneous integration of silicon logic with active compound semiconductor devices regardless of their original wafer dimensions. We detail the fabrication process, focusing on accessible through-silicon via (TSV) formation using standard magnetron sputtering to minimize infrastructure barriers. As a validation vehicle, a commercial mini-LED array is heterogeneously integrated onto a 180 nm node silicon shuttle die via room-temperature direct Cu semi-additive plating bonding. Electrical characterization confirms vertical interconnects, and the active driving of the mini-LED array is successfully demonstrated. This work establishes a viable pathway for the high-mix, low-volume manufacturing of heterogeneous 3D systems without rigid foundry constraints.
- Open Access
- 1 July 2026
- Published by IOP Publishing in Applied Physics Express
- Vol. 19 (7) , 071001
Low-temperature Cu/SiO 2 hybrid bonding by self-aligned in situ reductive Cu passivation
We demonstrate a 250 °C Cu/SiO 2 hybrid bonding process enabled by a selective complex reaction on Cu pads. The process forms a nitrogen-coordinated reactive passivation via self-aligned oxide reduction and surface modification, incorporating reducing species within the surface layer. During thermal bonding, this layer can participate in interfacial reactions, thereby helping suppress oxides and improve interfacial conduction. While bonding at 200 °C was also examined, the resulting electrical performance was limited. Electrical characterization of 8 μm-pitch daisy chains shows a minimum resistance of 42 mΩ.
- 1 July 2026
- Published by IOP Publishing in Applied Physics Express
- Vol. 19 (7) , 071001
Open AccessLow-temperature Cu/SiO 2 hybrid bonding by self-aligned in situ reductive Cu passivation
We demonstrate a 250 °C Cu/SiO 2 hybrid bonding process enabled by a selective complex reaction on Cu pads. The process forms a nitrogen-coordinated reactive passivation via self-aligned oxide reduction and surface modification, incorporating reducing species within the surface layer. During thermal bonding, this layer can participate in interfacial reactions, thereby helping suppress oxides and improve interfacial conduction. While bonding at 200 °C was also examined, the resulting electrical performance was limited. Electrical characterization of 8 μm-pitch daisy chains shows a minimum resistance of 42 mΩ.
- Open Access
- 20 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Emerging and Selected Topics in Circuits and Systems
- Vol. PP (21563357) , 1
Die-Level Transformation of 2D Shuttle Chips into 3D-IC for Advanced Rapid Prototyping using Meta Bonding
Three-dimensional integrated circuit (3D-IC) technology, often referred to as through-silicon via (TSV) formation technology, has been steadily maturing and is increasingly used in advanced semiconductor devices such as 3D complementary metal-oxide-semiconductor image sensors, high-bandwidth memory, and static random-access memory on central processing units (commonly known as 3D V-Cache). However, the initial development costs remain prohibitively high, primarily due to the substantial investment required for TSV formation at the wafer level. Meanwhile, conventional system-on-chip designs are transitioning from fin field-effect transistor to gate-all-around architectures using the latest sub-3 nm technology nodes and incorporating extreme ultraviolet lithography along with other cutting-edge techniques. Simultaneously, the academic community is fostering an environment that supports technology node utilization from legacy 180 to 7 nm, enabling designers to develop two-dimensional IC (2D-IC) chips with novel architectures at reduced costs. Despite these advancements, foundry shuttle services utilizing TSVs remain largely inaccessible, making proof-of-principle demonstrations and functional verification using 3D-ICs extremely challenging. This study introduces recent technological advancements that enable the transformation of 2D-ICs into 3D-ICs using shuttle chips from multi-project wafers, ranging from small to large-scale implementations. The discussion primarily focuses on die-level, short-turnaround-time 3D-IC fabrication, emphasizing key enabling technologies such as multichip thinning and TSV/microbump formation. In addition, the study explores the effectiveness of Meta BondingTM techniques, including fine-pitch microbump, direct bonding, and hybrid bonding, for future high-performance 3D-IC prototyping.
- 20 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Emerging and Selected Topics in Circuits and Systems
- Vol. PP (21563357) , 1
Open AccessDie-Level Transformation of 2D Shuttle Chips into 3D-IC for Advanced Rapid Prototyping using Meta Bonding
Three-dimensional integrated circuit (3D-IC) technology, often referred to as through-silicon via (TSV) formation technology, has been steadily maturing and is increasingly used in advanced semiconductor devices such as 3D complementary metal-oxide-semiconductor image sensors, high-bandwidth memory, and static random-access memory on central processing units (commonly known as 3D V-Cache). However, the initial development costs remain prohibitively high, primarily due to the substantial investment required for TSV formation at the wafer level. Meanwhile, conventional system-on-chip designs are transitioning from fin field-effect transistor to gate-all-around architectures using the latest sub-3 nm technology nodes and incorporating extreme ultraviolet lithography along with other cutting-edge techniques. Simultaneously, the academic community is fostering an environment that supports technology node utilization from legacy 180 to 7 nm, enabling designers to develop two-dimensional IC (2D-IC) chips with novel architectures at reduced costs. Despite these advancements, foundry shuttle services utilizing TSVs remain largely inaccessible, making proof-of-principle demonstrations and functional verification using 3D-ICs extremely challenging. This study introduces recent technological advancements that enable the transformation of 2D-ICs into 3D-ICs using shuttle chips from multi-project wafers, ranging from small to large-scale implementations. The discussion primarily focuses on die-level, short-turnaround-time 3D-IC fabrication, emphasizing key enabling technologies such as multichip thinning and TSV/microbump formation. In addition, the study explores the effectiveness of Meta BondingTM techniques, including fine-pitch microbump, direct bonding, and hybrid bonding, for future high-performance 3D-IC prototyping.
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 45-48
FOWLP-based Flexible Hybrid Electronics I: Photobiomodulation Device Fabrication on Hydrogel Substrate Using RDL-first Approach
This paper focuses on the fabrication of a PhotoBioModulation (PBM) device as a kind of flexible hybrid electronics (FHE) with a hydrogel substrate. PBM is a type of phototherapy using visible or near-infrared (NIR) light from LEDs or lasers. We propose an integrated PBM patch using RDL (redistribution layer)-first fan-out wafer-level packaging (FOWLP) with an array of embedded NIR mini-LEDs in the hydrogel as a substrate for chronic wound or bedsore healing. This paper characterizes the fan-out wirings formed on the hydrogel and describes multichip-to-wafer bonding with the mini-LEDs.
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 45-48
FOWLP-based Flexible Hybrid Electronics I: Photobiomodulation Device Fabrication on Hydrogel Substrate Using RDL-first Approach
This paper focuses on the fabrication of a PhotoBioModulation (PBM) device as a kind of flexible hybrid electronics (FHE) with a hydrogel substrate. PBM is a type of phototherapy using visible or near-infrared (NIR) light from LEDs or lasers. We propose an integrated PBM patch using RDL (redistribution layer)-first fan-out wafer-level packaging (FOWLP) with an array of embedded NIR mini-LEDs in the hydrogel as a substrate for chronic wound or bedsore healing. This paper characterizes the fan-out wirings formed on the hydrogel and describes multichip-to-wafer bonding with the mini-LEDs.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Development of Trans-nail PPG Controller Using Fingertip Blood Volume Changes to Enable Highly Accurate Motion Prediction
The widespread adoption of Virtual Reality (VR)/Augmented Reality (AR) has increased the demand for versatile controllers for VR/AR. Most conventional controllers for VR/AR have issues with a lack of immersive sensation, comfort, and stability. This study proposes a trans-nail PPG (photoplethysmography) controller using fingertip blood volume changes to enable accurate motion prediction. This controller utilizes the fact that the mainly DC component of the PPG signal varies with the state and movement of the hand and fingers. Based on reservoir computing, this controller also learns the PPG signals under various conditions and predicts the state and movement of the hand and fingers. Since this controller is attached to the fingernail, it does not compromise immersion, comfort, or stability. Three PPG sensor circuits in the trans-nail PPG sensor were designed, prototyped, and assembled with an LED on a nail-sized PCB. The output signals of the PPG sensor for various motions such as thumb raising and lowering, wrist raising and lowering, and wrist twisting were used for the learning and predictions of reservoir computing. As a result, the motion predictions with accuracies of over 90% were achieved successfully.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Development of Trans-nail PPG Controller Using Fingertip Blood Volume Changes to Enable Highly Accurate Motion Prediction
The widespread adoption of Virtual Reality (VR)/Augmented Reality (AR) has increased the demand for versatile controllers for VR/AR. Most conventional controllers for VR/AR have issues with a lack of immersive sensation, comfort, and stability. This study proposes a trans-nail PPG (photoplethysmography) controller using fingertip blood volume changes to enable accurate motion prediction. This controller utilizes the fact that the mainly DC component of the PPG signal varies with the state and movement of the hand and fingers. Based on reservoir computing, this controller also learns the PPG signals under various conditions and predicts the state and movement of the hand and fingers. Since this controller is attached to the fingernail, it does not compromise immersion, comfort, or stability. Three PPG sensor circuits in the trans-nail PPG sensor were designed, prototyped, and assembled with an LED on a nail-sized PCB. The output signals of the PPG sensor for various motions such as thumb raising and lowering, wrist raising and lowering, and wrist twisting were used for the learning and predictions of reservoir computing. As a result, the motion predictions with accuracies of over 90% were achieved successfully.
- 8 September 2023
- Published by Japan Society of Applied Physics
High-Bendable 3D Corrugated Interconnections for Chiplet-Embedded Flexible Hybrid Electronics Using Wafer-Level Packaging
2023 International Conference on Solid State Devices and Materials ,High-Bendable 3D Corrugated Interconnections for Chiplet-Embedded Flexible Hybrid Electronics Using Wafer-Level Packaging
- 8 September 2023
- Published by Japan Society of Applied Physics
High-Bendable 3D Corrugated Interconnections for Chiplet-Embedded Flexible Hybrid Electronics Using Wafer-Level Packaging
2023 International Conference on Solid State Devices and Materials ,High-Bendable 3D Corrugated Interconnections for Chiplet-Embedded Flexible Hybrid Electronics Using Wafer-Level Packaging
- Open Access
- 27 June 2023
- Published by MDPI AG in Electronics
- Vol. 12 (13) , 2836
An Electronic Microsaccade Circuit with Charge-Balanced Stimulation and Flicker Vision Prevention for an Artificial Eyeball System
This paper presents the first circuit that enables microsaccade function in an artificial eyeball system. Currently, the artificial eyeball is receiving increasing development in vision restoration. The main challenge is that the human eye is born with microsaccade that helps refresh vision, avoiding perception fading while the gaze is fixed for a long period, and without microsaccade, high-quality vision restoration is difficult. The proposed electronic microsaccade (E-μSaccade) circuit addresses the issue, and it is intrinsically safe because only charge-balanced stimulus pulses are allowed for stimulation. The E-μSaccade circuit adopts light-to-frequency modulation; due to the circuit’s leakage and dark current of light-sensitive elements, stimulus pulses of a frequency lower than tens of Hz occur, which is the cause of flickering vision. A flicker vision prevention (FVP) circuit is proposed to mitigate the issue. The proposed circuits are designed in a 0.18 μm standard CMOS process. The simulation and measurement results show that the E-μSaccade circuit helps refresh the stimulation pattern and blocks the low-frequency output.
- 27 June 2023
- Published by MDPI AG in Electronics
- Vol. 12 (13) , 2836
Open AccessAn Electronic Microsaccade Circuit with Charge-Balanced Stimulation and Flicker Vision Prevention for an Artificial Eyeball System
This paper presents the first circuit that enables microsaccade function in an artificial eyeball system. Currently, the artificial eyeball is receiving increasing development in vision restoration. The main challenge is that the human eye is born with microsaccade that helps refresh vision, avoiding perception fading while the gaze is fixed for a long period, and without microsaccade, high-quality vision restoration is difficult. The proposed electronic microsaccade (E-μSaccade) circuit addresses the issue, and it is intrinsically safe because only charge-balanced stimulus pulses are allowed for stimulation. The E-μSaccade circuit adopts light-to-frequency modulation; due to the circuit’s leakage and dark current of light-sensitive elements, stimulus pulses of a frequency lower than tens of Hz occur, which is the cause of flickering vision. A flicker vision prevention (FVP) circuit is proposed to mitigate the issue. The proposed circuits are designed in a 0.18 μm standard CMOS process. The simulation and measurement results show that the E-μSaccade circuit helps refresh the stimulation pattern and blocks the low-frequency output.
- 7 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Negative-Thermal-Expansion Gate Electrode to Introduce Tensile Strain into the Channel of MOSFETs for Mobility Enhancement
Herein, the use of a negative-thermal-expansion (NTE) material as a gate electrode to introduce a large tensile strain into a MOSFET channel is proposed. Manganese nitride (MnN), which has an antiperovskite crystal structure, is an NTE material. MOSFETs with a MnN gate as the negative-thermal-expansion gate electrode (NTEG) are fabricated and evaluated. MOSFETs with an NTEG exhibit a 10% increase in electron mobility. The results indicate that the NTEG is promising as a mobility enhancement technology.
- 7 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Negative-Thermal-Expansion Gate Electrode to Introduce Tensile Strain into the Channel of MOSFETs for Mobility Enhancement
Herein, the use of a negative-thermal-expansion (NTE) material as a gate electrode to introduce a large tensile strain into a MOSFET channel is proposed. Manganese nitride (MnN), which has an antiperovskite crystal structure, is an NTE material. MOSFETs with a MnN gate as the negative-thermal-expansion gate electrode (NTEG) are fabricated and evaluated. MOSFETs with an NTEG exhibit a 10% increase in electron mobility. The results indicate that the NTEG is promising as a mobility enhancement technology.
- Open Access
- 19 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (3) , 500-503
Room-Temperature Direct Cu Semi-Additive Plating (SAP) Bonding for Chip-on-Wafer 3D Heterogenous Integration With μLED
This letter describes a direct Cu bonding technology to there-dimensionally integrate heterogeneous dielets based on a chip-on-wafer configuration. 100-$\mu \text{m}$ -cubed blue$\mu $ LEDs temporarily adhered on a photosensitive resin are interconnected by semi-additive plating (SAP) without thermal compression bonding. By using SAP bonding, a lot of dielets can be stacked on thin 3D-IC chiplets. The following three key technologies are applied to solve the yield issues of SAP bonding. After pick-and-place assembly, additional coplanarity enhancement eliminates Cu bridges grown to a small gap between the$\mu $ LEDs and photosensitive resin. The$\mu $ LEDs arrays with sidewalls insulated by room-temperature ozone-ethylene-radical (OER)-SiO2-CVD are successfully bonded on sapphire wafers and a thin 3D-IC with through-Si via (TSV). Further design optimization is required, but partial seed pre-etching works well to increase the yield. Fully integrated module implementation with the 3D-ICs will be the next stage, however, we discuss a superior prospect for yield enhancement toward nearly 100%.- 19 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (3) , 500-503
Open AccessRoom-Temperature Direct Cu Semi-Additive Plating (SAP) Bonding for Chip-on-Wafer 3D Heterogenous Integration With μLED
This letter describes a direct Cu bonding technology to there-dimensionally integrate heterogeneous dielets based on a chip-on-wafer configuration. 100-$\mu \text{m}$ -cubed blue$\mu $ LEDs temporarily adhered on a photosensitive resin are interconnected by semi-additive plating (SAP) without thermal compression bonding. By using SAP bonding, a lot of dielets can be stacked on thin 3D-IC chiplets. The following three key technologies are applied to solve the yield issues of SAP bonding. After pick-and-place assembly, additional coplanarity enhancement eliminates Cu bridges grown to a small gap between the$\mu $ LEDs and photosensitive resin. The$\mu $ LEDs arrays with sidewalls insulated by room-temperature ozone-ethylene-radical (OER)-SiO2-CVD are successfully bonded on sapphire wafers and a thin 3D-IC with through-Si via (TSV). Further design optimization is required, but partial seed pre-etching works well to increase the yield. Fully integrated module implementation with the 3D-ICs will be the next stage, however, we discuss a superior prospect for yield enhancement toward nearly 100%.