Shangzhi Pan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Shangzhi Pan has a total of 69 co-authors. Here are the top co-authors by number of shared publications:
- Xiaoming Zha
Wuhan University
34 shared publications - Jinwu Gong
Hubei Key Laboratory of Power Equipment and System Security for Integrated Energy, School of Electrical Engineering and Automation, Wuhan University, Wuhan, China
25 shared publications - Fei Liu
School of Electrical Engineering and Automation, Wuhan University, Wuhan, China
14 shared publications - Zisen Lin
Hubei Key Laboratory of Power Equipment and System Security for Integrated Energy, School of Electrical Engineering and Automation, Wuhan University, Wuhan, China
12 shared publications - Jianbo Jiang
School of Engineering Dali University Dali China
9 shared publications - Liangzhong Yao
Wuhan University
8 shared publications
Latest Publications
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73  (8) , 11187-11199
A Six-Phase Soft-Switching Motor Driving Topology and Its Modulation Strategy for Low Common-Mode Voltage
This article proposes a six phase synchronous auxiliary resonant commutated pole soft switching inverter (6P-SARCP) for dual three-phase permanent magnet synchronous motor (DT-PMSM). By introducing two resonant inductors, the proposed new topology realizes the zero voltage turn-on condition of all the main circuit switches, which significantly reduces the switching loss of the main switching elements in the working process. On the other hand, this topology uses edge aligned PWM (EAPWM) scheme, which not only simplifies the control process of the auxiliary branch, but also further reduces the demand for controller resources. Further analysis shows that the modulation method can keep the system running efficiently and suppress the common mode voltage of the double three-phase system to 0.167·V DC. To verify the effectiveness and practicability of the above theoretical analysis results, a detailed simulation study and experimental tests are carried out. The final data show that the proposed 6P-SARCP topology combined with EAPWM modulation strategy performs well in improving the performance of DT-PMSM, and has high engineering application value.
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73  (8) , 11187-11199
A Six-Phase Soft-Switching Motor Driving Topology and Its Modulation Strategy for Low Common-Mode Voltage
This article proposes a six phase synchronous auxiliary resonant commutated pole soft switching inverter (6P-SARCP) for dual three-phase permanent magnet synchronous motor (DT-PMSM). By introducing two resonant inductors, the proposed new topology realizes the zero voltage turn-on condition of all the main circuit switches, which significantly reduces the switching loss of the main switching elements in the working process. On the other hand, this topology uses edge aligned PWM (EAPWM) scheme, which not only simplifies the control process of the auxiliary branch, but also further reduces the demand for controller resources. Further analysis shows that the modulation method can keep the system running efficiently and suppress the common mode voltage of the double three-phase system to 0.167·V DC. To verify the effectiveness and practicability of the above theoretical analysis results, a detailed simulation study and experimental tests are carried out. The final data show that the proposed 6P-SARCP topology combined with EAPWM modulation strategy performs well in improving the performance of DT-PMSM, and has high engineering application value.
- 5 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (6) , 9115-9132
A Combined M3C Suitable for Motor Drive Systems Operating at Close or Equal Input–Output Frequencies
The modular multilevel matrix converter (M3C) is a topology that can directly realize the ac–ac power conversion and is widely used in high-power motor drive applications. However, when the motor frequency is close to the grid frequency, the voltage fluctuation problem of the submodule capacitors worsens. The traditional method of reducing capacitor voltage fluctuations is to inject common-mode voltage and circulating current, resulting in an increase in voltage and current stress of the bridge arms. In this article, a new topology of M3C combined with a cascaded H-bridge is proposed, which can effectively reduce fluctuations in the capacitor voltage of the M3C bridge arm submodule when the input and output frequencies are close or equal, while it still has the advantages of the traditional M3C, such as easy modular design, low output harmonics, and strong scalability. First, a mathematical model of the combined M3C topology is established. With the model, the cause of the capacitor voltage fluctuations of the M3C bridge arm is analyzed, and its mathematical expression is derived when the motor frequency is close to or equal to the grid frequency. Then, a capacitive compensation method using cascaded H-bridges is proposed to provide the reactive power required by the motor to reduce fluctuations in the capacitor voltage of the M3C bridge arm submodule under the close or equal frequency working condition. Compared with the conventional methods, the combined M3C achieves smaller voltage fluctuations of the capacitors, eliminates the need for common-mode voltage and circulating current injection, and achieves lower power loss. Finally, the correctness and effectiveness of the proposed topology and control strategy are verified by simulations and experiments.
- 5 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (6) , 9115-9132
A Combined M3C Suitable for Motor Drive Systems Operating at Close or Equal Input–Output Frequencies
The modular multilevel matrix converter (M3C) is a topology that can directly realize the ac–ac power conversion and is widely used in high-power motor drive applications. However, when the motor frequency is close to the grid frequency, the voltage fluctuation problem of the submodule capacitors worsens. The traditional method of reducing capacitor voltage fluctuations is to inject common-mode voltage and circulating current, resulting in an increase in voltage and current stress of the bridge arms. In this article, a new topology of M3C combined with a cascaded H-bridge is proposed, which can effectively reduce fluctuations in the capacitor voltage of the M3C bridge arm submodule when the input and output frequencies are close or equal, while it still has the advantages of the traditional M3C, such as easy modular design, low output harmonics, and strong scalability. First, a mathematical model of the combined M3C topology is established. With the model, the cause of the capacitor voltage fluctuations of the M3C bridge arm is analyzed, and its mathematical expression is derived when the motor frequency is close to or equal to the grid frequency. Then, a capacitive compensation method using cascaded H-bridges is proposed to provide the reactive power required by the motor to reduce fluctuations in the capacitor voltage of the M3C bridge arm submodule under the close or equal frequency working condition. Compared with the conventional methods, the combined M3C achieves smaller voltage fluctuations of the capacitors, eliminates the need for common-mode voltage and circulating current injection, and achieves lower power loss. Finally, the correctness and effectiveness of the proposed topology and control strategy are verified by simulations and experiments.
- 11 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (5) , 8229-8241
Variable Voltage Level Based EPS Control for Three-Port DAB Converter to Achieve Current Stress Optimization
This article proposes a variable voltage level base extended phase shift (V2L-EPS) control for three-port dual active bridge (DAB) converter to achieve current stress optimization. By modifying the flying capacitor voltage balance control, the inner phase shift angle of DAB converter is released and can be used to realize extended phase shift (EPS) control. Furthermore, a variable voltage level can be constructed on the midpoint voltage of the primary side bridge arm by actively creating the unbalance of the flying capacitor voltage, so that the voltage excitation on the series inductor in the DAB converter varies within the inner phase shift interval thereby realizing a reconfiguration of the series inductor current, which reduces the high circulating power of the EPS control under light load conditions. In addition, by calculating the optimized trajectory of the V2L-EPS control, the current stress of the three port DAB converter is substantially reduced while ensuring all switches of the three port DAB converter operate under soft switching conditions over the full load range. Finally, a 500 W rated prototype is built to verify the effectiveness of the proposed V2L-EPS control.
- 11 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (5) , 8229-8241
Variable Voltage Level Based EPS Control for Three-Port DAB Converter to Achieve Current Stress Optimization
This article proposes a variable voltage level base extended phase shift (V2L-EPS) control for three-port dual active bridge (DAB) converter to achieve current stress optimization. By modifying the flying capacitor voltage balance control, the inner phase shift angle of DAB converter is released and can be used to realize extended phase shift (EPS) control. Furthermore, a variable voltage level can be constructed on the midpoint voltage of the primary side bridge arm by actively creating the unbalance of the flying capacitor voltage, so that the voltage excitation on the series inductor in the DAB converter varies within the inner phase shift interval thereby realizing a reconfiguration of the series inductor current, which reduces the high circulating power of the EPS control under light load conditions. In addition, by calculating the optimized trajectory of the V2L-EPS control, the current stress of the three port DAB converter is substantially reduced while ensuring all switches of the three port DAB converter operate under soft switching conditions over the full load range. Finally, a 500 W rated prototype is built to verify the effectiveness of the proposed V2L-EPS control.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Sustainable Energy
- Vol. 17  (2) , 1614-1626
A Multiport Multilevel Inverter With a Parallel Structure for Integrating Distributed Photovoltaic to MVAC With Power Mismatch Elimination
The Cascaded H-bridge (CHB) multilevel inverter stands out as an optimal topology for integrating large-scale photovoltaic (PV) power systems into the grid. Due to its multiport characteristic, each submodule directly interfaces with distributed PV strings. Nonetheless, PV power generation often experiences mismatches among three phases and between arms of one phase due to factors such as nonuniform irradiation, partial shading, and temperature variations. Addressing these challenges, this study introduces a novel CHB multilevel inverter with a parallel structure. Consequently, the added power circulation paths facilitate phase power exchange through circulating current injection (CCI), effectively eliminating phase power mismatch and power mismatch between arms in one phase. By transitioning the power exchange mode from voltage-driven to current-driven, the prevalent voltage overmodulation issue associated with the traditional CHB multilevel inverter is resolved. Additionally, this study offers a quantitative assessment of the power balancing capability of the suggested inverter in PV applications. Evidence suggests that, by employing CCI, the proposed inverter significantly enhances power balance capabilities compared to the traditional CHB multilevel inverter that utilizes zero-sequence voltage injection (ZSVI). Both simulation and experimental results validate the proposed approach.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Sustainable Energy
- Vol. 17  (2) , 1614-1626
A Multiport Multilevel Inverter With a Parallel Structure for Integrating Distributed Photovoltaic to MVAC With Power Mismatch Elimination
The Cascaded H-bridge (CHB) multilevel inverter stands out as an optimal topology for integrating large-scale photovoltaic (PV) power systems into the grid. Due to its multiport characteristic, each submodule directly interfaces with distributed PV strings. Nonetheless, PV power generation often experiences mismatches among three phases and between arms of one phase due to factors such as nonuniform irradiation, partial shading, and temperature variations. Addressing these challenges, this study introduces a novel CHB multilevel inverter with a parallel structure. Consequently, the added power circulation paths facilitate phase power exchange through circulating current injection (CCI), effectively eliminating phase power mismatch and power mismatch between arms in one phase. By transitioning the power exchange mode from voltage-driven to current-driven, the prevalent voltage overmodulation issue associated with the traditional CHB multilevel inverter is resolved. Additionally, this study offers a quantitative assessment of the power balancing capability of the suggested inverter in PV applications. Evidence suggests that, by employing CCI, the proposed inverter significantly enhances power balance capabilities compared to the traditional CHB multilevel inverter that utilizes zero-sequence voltage injection (ZSVI). Both simulation and experimental results validate the proposed approach.
- 5 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13  (6) , 7993-8006
Three-Phase Fully Magnetically Integrated LCL Filters With Enhanced Ripple Attenuation Capability
High efficiency and high power density are the trends in power electronic converters. However, conventional LCL filters suffer from low core utilization and high volume redundancy. This is one of the key factors limiting the improvement of power density in grid-connected inverters. Three-phase grid-connected inverters require more filtering inductors and the problem of volume redundancy is even more pronounced. However, existing filter magnetic integration techniques suffer from varying degrees of degradation in ripple attenuation capability. To address above problem, a three-phase fully magnetically integrated LCL (TPFMI-LCL) filter with enhanced ripple attenuation capability is proposed in this paper. The proposed TPFMI-LCL integrates all filter inductors on the same magnetic core, which eliminates the volume redundancy of the filter. In addition, a rational core size parameter design is carried out to achieve the joint optimization of filter volume and loss. Compared with the conventional three-phase LCL filter, the advantages of the proposed TPFMI-LCL are enhanced ripple attenuation capability and reduced size. Finally, a laboratory prototype is built to verify the effectiveness of the proposed TPFMI-LCL filter.
- 5 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13  (6) , 7993-8006
Three-Phase Fully Magnetically Integrated LCL Filters With Enhanced Ripple Attenuation Capability
High efficiency and high power density are the trends in power electronic converters. However, conventional LCL filters suffer from low core utilization and high volume redundancy. This is one of the key factors limiting the improvement of power density in grid-connected inverters. Three-phase grid-connected inverters require more filtering inductors and the problem of volume redundancy is even more pronounced. However, existing filter magnetic integration techniques suffer from varying degrees of degradation in ripple attenuation capability. To address above problem, a three-phase fully magnetically integrated LCL (TPFMI-LCL) filter with enhanced ripple attenuation capability is proposed in this paper. The proposed TPFMI-LCL integrates all filter inductors on the same magnetic core, which eliminates the volume redundancy of the filter. In addition, a rational core size parameter design is carried out to achieve the joint optimization of filter volume and loss. Compared with the conventional three-phase LCL filter, the advantages of the proposed TPFMI-LCL are enhanced ripple attenuation capability and reduced size. Finally, a laboratory prototype is built to verify the effectiveness of the proposed TPFMI-LCL filter.
- 11 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 40  (6) , 5476-5479
Complex Frequency Locked Loop for Estimations of RoCoV and Frequency
Recently, the concept of complex frequency (CF) has been introduced to unify the rate of change of voltage (RoCoV) and angular frequency, facilitating the development of CF-based droop control. However, in conventional grid synchronization, the amplitude of the measured bus voltage is typically computed in an open-loop fashion, and RoCoV is not estimated. In this letter, a complex frequency-locked loop (CFLL) is proposed to estimate the CF including both RoCoV and frequency information. In the proposed CFLL, RoCoV is estimated using closed-loop feedback, resulting in improved performance compared to conventional discrete-time differentiation and synchronous reference frame phase-locked loop (SRF-PLL) based methods. The dynamic response of the RoCoV also becomes symmetric with that of the frequency estimation. Experimental results validate the effectiveness of the proposed CFLL.
- 11 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 40  (6) , 5476-5479
Complex Frequency Locked Loop for Estimations of RoCoV and Frequency
Recently, the concept of complex frequency (CF) has been introduced to unify the rate of change of voltage (RoCoV) and angular frequency, facilitating the development of CF-based droop control. However, in conventional grid synchronization, the amplitude of the measured bus voltage is typically computed in an open-loop fashion, and RoCoV is not estimated. In this letter, a complex frequency-locked loop (CFLL) is proposed to estimate the CF including both RoCoV and frequency information. In the proposed CFLL, RoCoV is estimated using closed-loop feedback, resulting in improved performance compared to conventional discrete-time differentiation and synchronous reference frame phase-locked loop (SRF-PLL) based methods. The dynamic response of the RoCoV also becomes symmetric with that of the frequency estimation. Experimental results validate the effectiveness of the proposed CFLL.
- 29 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72  (12) , 12096-12107
An Interleaved Boost Converter With an Integrated Active Ripple Cancellation Filter
In this article, an interleaved boost converter with an integrated active ripple cancellation filter (IARCF) is presented, which is able to offer nearly duty-cycle-independent and switching-frequency-independent switching ripple cancellation capability. The inter-bridge positive coupling and inter-phase negative coupling of the integrated filter actively cancel the switching current ripple by generating mutual-inductance voltage to offset the switching voltage on the main inductor in a wide voltage range. An integrated magnetic core structure is proposed to implement the active filter, which is able to achieve partial flux cancellation and convert the ripple cancellation condition into adjusting the winding turn ratio, thereby making parameter matching easier. The accuracy of the theoretical analysis and the validity of the proposed converter and the magnetic core structure are verified by simulation and experimental results. Importantly, the proposed interleaving IARCF and magnetic core structure are versatile and can be readily applied to inverter and rectifier applications.
- 29 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72  (12) , 12096-12107
An Interleaved Boost Converter With an Integrated Active Ripple Cancellation Filter
In this article, an interleaved boost converter with an integrated active ripple cancellation filter (IARCF) is presented, which is able to offer nearly duty-cycle-independent and switching-frequency-independent switching ripple cancellation capability. The inter-bridge positive coupling and inter-phase negative coupling of the integrated filter actively cancel the switching current ripple by generating mutual-inductance voltage to offset the switching voltage on the main inductor in a wide voltage range. An integrated magnetic core structure is proposed to implement the active filter, which is able to achieve partial flux cancellation and convert the ripple cancellation condition into adjusting the winding turn ratio, thereby making parameter matching easier. The accuracy of the theoretical analysis and the validity of the proposed converter and the magnetic core structure are verified by simulation and experimental results. Importantly, the proposed interleaving IARCF and magnetic core structure are versatile and can be readily applied to inverter and rectifier applications.
- 21 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40  (9) , 13099-13112
A Magnetic Integrated LCL Filter With Enhanced Ripple Attenuation Capability and a Core Size Optimization Method
In virtue of their strong ripple attenuation capability, LCL filters are widely used in grid-connected inverter to effectively filter the switching frequency harmonics of grid-connected currents. However, the downside of conventional LCL filters is that they are large size and low core utilization. Although magnetic integration of the two discrete inductors of the LCL filter is an effective solution to reduce the size, the existing magnetic integration solutions mainly suffer from the problem of reduced ripple attenuating capability in high frequency zone. Aiming at this problem, a magnetic integrated LCL filter with enhanced ripple attenuation capability is proposed in this article. In addition, the joint optimization method of core volume-efficiency-ripple attenuation capability is realized by reasonable core structure and parameter design, which further improves the practicability of the proposed magnetic integrated LCL filter. Finally, the effectiveness of the proposed magnetic integrated LCL filter and joint optimization method is experimentally verified.
- 21 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40  (9) , 13099-13112
A Magnetic Integrated LCL Filter With Enhanced Ripple Attenuation Capability and a Core Size Optimization Method
In virtue of their strong ripple attenuation capability, LCL filters are widely used in grid-connected inverter to effectively filter the switching frequency harmonics of grid-connected currents. However, the downside of conventional LCL filters is that they are large size and low core utilization. Although magnetic integration of the two discrete inductors of the LCL filter is an effective solution to reduce the size, the existing magnetic integration solutions mainly suffer from the problem of reduced ripple attenuating capability in high frequency zone. Aiming at this problem, a magnetic integrated LCL filter with enhanced ripple attenuation capability is proposed in this article. In addition, the joint optimization method of core volume-efficiency-ripple attenuation capability is realized by reasonable core structure and parameter design, which further improves the practicability of the proposed magnetic integrated LCL filter. Finally, the effectiveness of the proposed magnetic integrated LCL filter and joint optimization method is experimentally verified.
- 7 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. PP  (02780046) , 1-11
A Circulating Current Suppression Method for Dual-Input Converter With Integrated Mismatch Power Processing Unit
The dual-input converter with integrated mismatch power processing unit (MP2U) can effectively eliminate the limitation of power transmission capability caused by pulse width modulation (PWM) control. However, its considerable circulating current increases the loss of switches and limits the improvement of its efficiency. In this article, a circulating current suppression method (CCSM) is proposed. By changing the inner phase shift angle of the integrated MP2U, the extra operating state of the MP2U can be used, and the working state sequence of the MP2U is reconstructed to change the current waveform in the MP2U. The proposed CCSM control can completely eliminate the circulating current when the two input ports are matched and greatly suppress the circulating current when the two input ports are mismatched, achieving the overall efficiency optimization of the dual-input converter. In addition, the optimized inner phase shift trajectory of the proposed CCSM control under different mismatch conditions is calculated, and the soft switching operation of all switches in MP2U is ensured. The proposed control method is verified by the experimental results of a 500 W prototype.
- 7 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. PP  (02780046) , 1-11
A Circulating Current Suppression Method for Dual-Input Converter With Integrated Mismatch Power Processing Unit
The dual-input converter with integrated mismatch power processing unit (MP2U) can effectively eliminate the limitation of power transmission capability caused by pulse width modulation (PWM) control. However, its considerable circulating current increases the loss of switches and limits the improvement of its efficiency. In this article, a circulating current suppression method (CCSM) is proposed. By changing the inner phase shift angle of the integrated MP2U, the extra operating state of the MP2U can be used, and the working state sequence of the MP2U is reconstructed to change the current waveform in the MP2U. The proposed CCSM control can completely eliminate the circulating current when the two input ports are matched and greatly suppress the circulating current when the two input ports are mismatched, achieving the overall efficiency optimization of the dual-input converter. In addition, the optimized inner phase shift trajectory of the proposed CCSM control under different mismatch conditions is calculated, and the soft switching operation of all switches in MP2U is ensured. The proposed control method is verified by the experimental results of a 500 W prototype.
- 20 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72  (7) , 7061-7071
A Dual DC-Bus Integrated DAB Converter With Voltage Match Control for Wide Voltage Range Applications
This article proposes a dual dc-bus integrated dual active bridge (DAB) converter with voltage match control for wide voltage range applications. The proposed converter has a feature of dual dc buses, one of which is adjustable while the other is always clamped by the input source. An auxiliary inductor is added to transmit power between the dual dc buses. The voltage of the adjustable dc-bus is regulated to match the voltages between two sides of the series inductor. With the voltage match control, the root mean square (rms) value of the transformer current is reduced and all switches can achieve theoretical full load range zero voltage switching (ZVS) operations. Furthermore, the auxiliary inductor processes only a portion of the main power and operates in continuous conduction mode (CCM), resulting in low losses and small size. Consequently, the efficiency is optimized over a wide voltage range. The working principle, working characteristics, and design considerations are introduced in detail. Finally, a 1 kW laboratory prototype is built to verify the theoretical analysis. The peak efficiency of the prototype is 96.8% and the efficiency over a wide range of voltage is always above 90%.
- 20 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72  (7) , 7061-7071
A Dual DC-Bus Integrated DAB Converter With Voltage Match Control for Wide Voltage Range Applications
This article proposes a dual dc-bus integrated dual active bridge (DAB) converter with voltage match control for wide voltage range applications. The proposed converter has a feature of dual dc buses, one of which is adjustable while the other is always clamped by the input source. An auxiliary inductor is added to transmit power between the dual dc buses. The voltage of the adjustable dc-bus is regulated to match the voltages between two sides of the series inductor. With the voltage match control, the root mean square (rms) value of the transformer current is reduced and all switches can achieve theoretical full load range zero voltage switching (ZVS) operations. Furthermore, the auxiliary inductor processes only a portion of the main power and operates in continuous conduction mode (CCM), resulting in low losses and small size. Consequently, the efficiency is optimized over a wide voltage range. The working principle, working characteristics, and design considerations are introduced in detail. Finally, a 1 kW laboratory prototype is built to verify the theoretical analysis. The peak efficiency of the prototype is 96.8% and the efficiency over a wide range of voltage is always above 90%.