Jean-Pol Dodelet
Research Subjects
Jean-Pol Dodelet has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Frédéric Jaouen
ENSCM
10 shared publications - Michel Lefèvre
INRS-EMT
10 shared publications - Régis Chenitz
INRS-Énergie, Matériaux et Télécommunications, 1650 Boulevard Lionel Boulet, Varennes, Québec, J3X 1S2, Canada
8 shared publications - Vassili P. Glibin
Department of Chemical and Biochemical Engineering, University of Western Ontario, London, N6A 5B9, Canada
8 shared publications - Gaixia Zhang
Department of Electrical Engineering, École de Technologie Supérieure (ETS), Montreal, QC H3C 1K3, Canada
7 shared publications - Shuhui Sun
Institut National de la Recherche Scientifique (INRS), Center Énergie Matériaux Télécommunications, Varennes, Quebec J3X 1P7, Canada
7 shared publications
Latest Publications
- Open Access
- 24 June 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (30) , 24849-24867
Ptn-Mn(II)Nx and Ptn-Mn(III)Nx are both winning combinations for the durability of these hybrid catalysts in PEM fuel cells: A deep insight into synergism between Pt clusters and MnNx/C sites
MnN x /C increases the adhesion strength of Pt( n ) on a carbon substrate and, in return, Pt( n ) stabilizes MnN x /C towards demetallation in strongly acidic fuel cell media.
- 24 June 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (30) , 24849-24867
Open AccessPtn-Mn(II)Nx and Ptn-Mn(III)Nx are both winning combinations for the durability of these hybrid catalysts in PEM fuel cells: A deep insight into synergism between Pt clusters and MnNx/C sites
MnN x /C increases the adhesion strength of Pt( n ) on a carbon substrate and, in return, Pt( n ) stabilizes MnN x /C towards demetallation in strongly acidic fuel cell media.
- 11 June 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (14) , 7245-7253
Selective synthesis of dense high-spin D1 active sites via engineered less-graphitized carbon environments
Fe–N–C catalysts are the most promising alternative to Pt for the oxygen reduction reaction (ORR) in proton exchange membrane fuel cells (PEMFCs). However, the mixture of two distinct active sites—highly active but unstable D1 and less active but more stable D2—has complicated the study of site-specific catalytic behaviors. Here we report a synthetic procedure to maximize the D1 site by introducing ascorbic acid (AA) as a perturbing molecule. The AA not only increases the single-atom loading, but also creates a less-graphitized carbon environment, featuring increased carbon defects and mesoporosity, which favors D1 site formation. This resulting catalyst exhibits over 80% D1 site and a substantially high D1 concentration of 2.13 wt%. The denser D1 sites, as well as the increased mesoporosity, enables a current density of 151 mA cm−2 at 0.8 V and a peak power density of 803 mW cm−2 at 1.5 bar air. Meanwhile, the catalyst loses 93% of its initial power within 50 hours. Both the activity and stability behaviors meet the characteristics of the D1 site. The study paves the way for the precise exploration of the D1 active site, not only for the ORR but also potentially for other catalytic processes.
- 11 June 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (14) , 7245-7253
Selective synthesis of dense high-spin D1 active sites via engineered less-graphitized carbon environments
Fe–N–C catalysts are the most promising alternative to Pt for the oxygen reduction reaction (ORR) in proton exchange membrane fuel cells (PEMFCs). However, the mixture of two distinct active sites—highly active but unstable D1 and less active but more stable D2—has complicated the study of site-specific catalytic behaviors. Here we report a synthetic procedure to maximize the D1 site by introducing ascorbic acid (AA) as a perturbing molecule. The AA not only increases the single-atom loading, but also creates a less-graphitized carbon environment, featuring increased carbon defects and mesoporosity, which favors D1 site formation. This resulting catalyst exhibits over 80% D1 site and a substantially high D1 concentration of 2.13 wt%. The denser D1 sites, as well as the increased mesoporosity, enables a current density of 151 mA cm−2 at 0.8 V and a peak power density of 803 mW cm−2 at 1.5 bar air. Meanwhile, the catalyst loses 93% of its initial power within 50 hours. Both the activity and stability behaviors meet the characteristics of the D1 site. The study paves the way for the precise exploration of the D1 active site, not only for the ORR but also potentially for other catalytic processes.
- Open Access
Non-PGM Electrocatalysts for PEM Fuel Cells: A DFT Study on the Effects of Fluorination of FeNx-Doped and N-Doped Carbon Catalysts
Fluorination is considered as a means of reducing the degradation of Fe/N/C, a highly active FeNx-doped disorganized carbon catalyst for the oxygen reduction reaction (ORR) in PEM fuel cells. Our recent experiments have, however, revealed that fluorination poisons the FeNx moiety of the Fe/N/C catalytic site, considerably reducing the activity of the resulting catalyst to that of carbon only doped with nitrogen. Using the density functional theory (DFT), we clarify in this work the mechanisms by which fluorine interacts with the catalyst. We studied 10 possible FeNx site configurations as well as 2 metal-free sites in the absence or presence of fluorine molecules and atoms. When the FeNx moiety is located on a single graphene layer accessible on both sides, we found that fluorine binds strongly to Fe but that two F atoms, one on each side of the FeNx plane, are necessary to completely inhibit the catalytic activity of the FeNx sites. When considering the more realistic model of a stack of graphene layers, only one F atom is needed to poison the FeNx moiety on the top layer since ORR hardly takes place between carbon layers. We also found that metal-free catalytic N-sites are immune to poisoning by fluorination, in accordance with our experiments. Finally, we explain how most of the catalytic activity can be recovered by heating to 900 °C after fluorination. This research helps to clarify the role of metallic sites compared to non-metallic ones upon the fluorination of FeNx-doped disorganized carbon catalysts.
Open AccessNon-PGM Electrocatalysts for PEM Fuel Cells: A DFT Study on the Effects of Fluorination of FeNx-Doped and N-Doped Carbon Catalysts
Fluorination is considered as a means of reducing the degradation of Fe/N/C, a highly active FeNx-doped disorganized carbon catalyst for the oxygen reduction reaction (ORR) in PEM fuel cells. Our recent experiments have, however, revealed that fluorination poisons the FeNx moiety of the Fe/N/C catalytic site, considerably reducing the activity of the resulting catalyst to that of carbon only doped with nitrogen. Using the density functional theory (DFT), we clarify in this work the mechanisms by which fluorine interacts with the catalyst. We studied 10 possible FeNx site configurations as well as 2 metal-free sites in the absence or presence of fluorine molecules and atoms. When the FeNx moiety is located on a single graphene layer accessible on both sides, we found that fluorine binds strongly to Fe but that two F atoms, one on each side of the FeNx plane, are necessary to completely inhibit the catalytic activity of the FeNx sites. When considering the more realistic model of a stack of graphene layers, only one F atom is needed to poison the FeNx moiety on the top layer since ORR hardly takes place between carbon layers. We also found that metal-free catalytic N-sites are immune to poisoning by fluorination, in accordance with our experiments. Finally, we explain how most of the catalytic activity can be recovered by heating to 900 °C after fluorination. This research helps to clarify the role of metallic sites compared to non-metallic ones upon the fluorination of FeNx-doped disorganized carbon catalysts.
- Open Access
- 1 September 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (9) , 094502
Non-PGM Electrocatalysts for PEM Fuel Cells: Thermodynamic Stability of Potential ORR CoNx-C Electrocatalytic Sites
We present here a thermodynamic assessment of the stability behavior in acidic environments at 298 and 353 K (80 °C) of several Co-based sites that may potentially be active for the oxygen reduction reaction (ORR) at the cathode of proton exchange membrane (PEM) fuel cells. These sites are: i) the porphyrin-like CoN4/C site located in a micropore, ii) two different 1,10-phenanthroline-like CoN(2+2)/C sites located either in a micropore or embedded into a graphene sheet, and iii) the CoN(4+2)/C site having (at its center) the structural motif of the hexa-aza-macrocyclic complex of Co(II) embedded into a graphene sheet. The calculations of the equilibrium constants ( K c ) for the reactions of demetallation indicate that all evaluated active sites are chemically stable in an acidic medium at both 298 and 353 K. At 298 K, K c values for CoN4/C and for the two examples of CoN(2+2)/C sites are very similar. The same conclusion is also true at 353 K. However, the simple introduction of two supplementary nitrogen atoms in the structure of the embedded hexa-aza CoN(4+2)/C site vs that of the embedded phenanthroline-like CoN(2+2)/C site significantly affects its stability toward Co2+ demetallation, rendering CoN(4+2)/C much less likely to demetallate than CoN(2+2)/C either at 298 or 353 K.
- 1 September 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (9) , 094502
Open AccessNon-PGM Electrocatalysts for PEM Fuel Cells: Thermodynamic Stability of Potential ORR CoNx-C Electrocatalytic Sites
We present here a thermodynamic assessment of the stability behavior in acidic environments at 298 and 353 K (80 °C) of several Co-based sites that may potentially be active for the oxygen reduction reaction (ORR) at the cathode of proton exchange membrane (PEM) fuel cells. These sites are: i) the porphyrin-like CoN4/C site located in a micropore, ii) two different 1,10-phenanthroline-like CoN(2+2)/C sites located either in a micropore or embedded into a graphene sheet, and iii) the CoN(4+2)/C site having (at its center) the structural motif of the hexa-aza-macrocyclic complex of Co(II) embedded into a graphene sheet. The calculations of the equilibrium constants ( K c ) for the reactions of demetallation indicate that all evaluated active sites are chemically stable in an acidic medium at both 298 and 353 K. At 298 K, K c values for CoN4/C and for the two examples of CoN(2+2)/C sites are very similar. The same conclusion is also true at 353 K. However, the simple introduction of two supplementary nitrogen atoms in the structure of the embedded hexa-aza CoN(4+2)/C site vs that of the embedded phenanthroline-like CoN(2+2)/C site significantly affects its stability toward Co2+ demetallation, rendering CoN(4+2)/C much less likely to demetallate than CoN(2+2)/C either at 298 or 353 K.
- 12 January 2021
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 14 (2) , 1034-1041
Reply to the ‘Comment on “Non-PGM electrocatalysts for PEM fuel cells: effect of fluorination on the activity and stability of a highly active NC_Ar + NH3 catalyst”’ by Xi Yin, Edward F. Holby and Piotr Zelenay, Energy Environ. Sci., 10.1039/D0EE02069A
The fast decay in PEM fuel cells of a highly active, high performance, but unstable Fe/N/C catalyst like our NC_Ar + NH3 follows a chemical, not an electrochemical, demetallation mechanism for its ORR active FeN4 sites in the catalyst micropores.
- 12 January 2021
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 14 (2) , 1034-1041
Reply to the ‘Comment on “Non-PGM electrocatalysts for PEM fuel cells: effect of fluorination on the activity and stability of a highly active NC_Ar + NH3 catalyst”’ by Xi Yin, Edward F. Holby and Piotr Zelenay, Energy Environ. Sci., 10.1039/D0EE02069A
The fast decay in PEM fuel cells of a highly active, high performance, but unstable Fe/N/C catalyst like our NC_Ar + NH3 follows a chemical, not an electrochemical, demetallation mechanism for its ORR active FeN4 sites in the catalyst micropores.
- Open Access
- 2 August 2019
- Published by Wiley in Advanced Materials
- Vol. 31 (31) , 1903622
Advancing Materials Electrochemistry for Chemical Transformation
- 2 August 2019
- Published by Wiley in Advanced Materials
- Vol. 31 (31) , 1903622
Open AccessAdvancing Materials Electrochemistry for Chemical Transformation
- 3 July 2019
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 12 (10) , 3015-3037
Non-PGM electrocatalysts for PEM fuel cells: effect of fluorination on the activity and stability of a highly active NC_Ar + NH 3 catalyst
F 2 -Fluorination of Fe/N/C catalysts poisons FeN 4 , but not CNx sites. Main causes of instability in PEMFCs are either FeN 4 demetalation for Fe/N/C or H 2 O 2 when FeN 4 sites are poisoned by fluorination or absent as in MOF_CNx_Ar + NH 3 .
- 3 July 2019
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 12 (10) , 3015-3037
Non-PGM electrocatalysts for PEM fuel cells: effect of fluorination on the activity and stability of a highly active NC_Ar + NH 3 catalyst
F 2 -Fluorination of Fe/N/C catalysts poisons FeN 4 , but not CNx sites. Main causes of instability in PEMFCs are either FeN 4 demetalation for Fe/N/C or H 2 O 2 when FeN 4 sites are poisoned by fluorination or absent as in MOF_CNx_Ar + NH 3 .
- Open Access
- 8 May 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (7) , F3277-F3286
Non-PGM Electrocatalysts for PEM Fuel Cells: Thermodynamic Stability and DFT Evaluation of Fluorinated FeN4-Based ORR Catalysts
Two types of FeN4-based catalytic sites have been proposed in the literature to perform the oxygen reduction reaction (ORR) in PEM fuel cells running with a Fe-based catalyst. They are FeN4/C, derived from the molecular structure of iron porphyrin, and FeN(2+2)/C, derived from the structure of the iron complex with two 1,10-phenanthroline molecules. The energetics and thermodynamic stability (equilibrium constant, Kc, for iron acid leaching at pH ∼ 0) of these two types of sites were determined and were already reported in this journal [J. Electrochem. Soc., 164(9) F948-F957 (2017)]. This work deals with the same FeN4 sites but this time after their fluorination on the central Fe atom and on their carbon support. All evaluated fluorinated FeN4-based sites are stable at both 298 and 353 K, especially F-FeN4/C(F) and F2-FeN(2+2)/C(F). Interatomic dFe − N, dFe − F, and bond energies EFe − F derived in the frame of the thermodynamic calculations were compared with the values obtained by density functional theory (DFT) calculations, and an agreement was found. DFT was also used to assess the ORR capability of both F-FeN4/C and F-FeN(2+2)/C. Both fluorinated sites were found to be ORR active when O2 was bonded to the free side of the Fe atom, opposite to the F atom.
- 8 May 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (7) , F3277-F3286
Open AccessNon-PGM Electrocatalysts for PEM Fuel Cells: Thermodynamic Stability and DFT Evaluation of Fluorinated FeN4-Based ORR Catalysts
Two types of FeN4-based catalytic sites have been proposed in the literature to perform the oxygen reduction reaction (ORR) in PEM fuel cells running with a Fe-based catalyst. They are FeN4/C, derived from the molecular structure of iron porphyrin, and FeN(2+2)/C, derived from the structure of the iron complex with two 1,10-phenanthroline molecules. The energetics and thermodynamic stability (equilibrium constant, Kc, for iron acid leaching at pH ∼ 0) of these two types of sites were determined and were already reported in this journal [J. Electrochem. Soc., 164(9) F948-F957 (2017)]. This work deals with the same FeN4 sites but this time after their fluorination on the central Fe atom and on their carbon support. All evaluated fluorinated FeN4-based sites are stable at both 298 and 353 K, especially F-FeN4/C(F) and F2-FeN(2+2)/C(F). Interatomic dFe − N, dFe − F, and bond energies EFe − F derived in the frame of the thermodynamic calculations were compared with the values obtained by density functional theory (DFT) calculations, and an agreement was found. DFT was also used to assess the ORR capability of both F-FeN4/C and F-FeN(2+2)/C. Both fluorinated sites were found to be ORR active when O2 was bonded to the free side of the Fe atom, opposite to the F atom.