Shutong Wang

Sensitivity and effective sensing range are core performance metrics of flexible pressure sensors, directly dictating their practical applicability. A key challenge in sensor design is sensitivity degradation with elevated pressure, hindering synergistic optimization of high sensitivity and broad sensing range, while cumbersome electrode fabrication further impedes facile preparation and large-scale deployment of high-performance devices. Herein, this work proposes a novel fabrication strategy for flexible iontronic pressure sensors via direct laser writing (DLW) technology. A controllable ultraviolet laser patterns polyimide substrates to fabricate hierarchical stepped conoid-like microstructural templates, which are transferred to ion gels through reverse molding. The DLW-enabled precise geometric control and hierarchical conical architectures efficiently amplify interfacial contact area variation under pressure, significantly boosting sensitivity. The resultant sensor achieves a high sensitivity of 118.4 kPa⁻¹ and a broad detection range up to 2000 kPa, with fast response/recovery times of 38.4 ms and 47 ms and excellent mechanical stability enduring 2000 loading–unloading cycles at 850 kPa. Multi-scenario physiological signal monitoring validates its accurate capture of laryngeal vibrations and joint movements. This work establishes a straightforward, efficient microfabrication route for high-performance flexible iontronic sensors, accelerating their practical application in wearable health monitoring and related fields.

Fabricating parabolic moth-eye structures on silica optical diffusers via dewetting-assisted plasma etching effectively manipulates light transmission and scattering. The tunable structures enhance transmittance by up to 17.42% and haze by 23.64%.

Micro/nanostructured Al substrates improve droplet deposition, plasma excitation, and LIBS spectral acquisition. Transfer learning improves cross-matrix Cr and Pb quantification in spiked real-water matrices.

Laser-patterned hydrophobic–hydrophilic enclosures confine droplets and suppress coffee-ring effects, boosting LIBS to ppb LODs for Cr, Pb and As ( R ² > 0.98). PLSR further improves quantitation, enabling a simple, scalable route for water monitoring.

By virtue of its narrow pulse width and high peak power, the femtosecond pulsed laser can achieve high-precision material modification, material additive or subtractive, and other forms of processing. With additional good material adaptability and process compatibility, femtosecond laser-induced application has achieved significant progress in flexible electronics in recent years. These advancements in the femtosecond laser fabrication of flexible electronic devices are comprehensively summarized here. This review first briefly introduces the physical mechanism and characteristics of the femtosecond laser fabrication of various electronic microdevices. It then focuses on effective methods of improving processing efficiency, resolution, and size. It further highlights the typical progress of applications, including flexible energy storage devices, nanogenerators, flexible sensors, and detectors, etc. Finally, it discusses the development tendency of ultrashort pulse laser processing. This review should facilitate the precision manufacturing of flexible electronics using a femtosecond laser.

We report a voltage-tunable reflective gold wire grid metasurface on vanadium dioxide thin film, which consists of a metal-insulator-metal (MIM) structure. We excite surface plasmon polariton (SPP) modes on the gold surface by fabricating a one-dimensional structured gold wire grid. Joule heating of laser-induced graphene (LIG) can be controlled by the voltage at the bottom, allowing vanadium dioxide in the structure to complete the transition from the insulating state to the metallic state. The phase transition of vanadium dioxide strongly disrupts the plasmon modes excited by the gold wire grid above, thereby realizing a huge change in the reflection spectrum. This acts as a tunable metasurface optical switch with a maximum modulation depth (MD) of over 20 dB. We provide a more effective and simple method for creating tunable metasurfaces in the near-infrared band, which can allow metasurfaces to have wider applications in optical signal processing, optical storage, and holography.

In this work, we fabricated the antireflection microstructures (ARMs) on ZnSe surfaces using a femtosecond Bessel direct laser writing in burst mode. The morphology and transmittance performance of ARMs with different single-pulse energies (from 200 nJ to 500 nJ), different burst modes (burst 1, 3, and 5 modes), different periods (from 3 μm to 6 μm), and different arrangements were investigated. The results revealed that tetragonally arranged ARMs fabricated by 500 nJ of single-pulse energy, the burst 3 mode, and a period of 3 μm show the best transmittance performance. The average transmittance of the ARMs was about 17.13% higher than that of bulk ZnSe in the range of 8–12 μm, and the highest transmittance of 81.75% (an improvement of 18.63% on one side of the ZnSe) was achieved at 12.36 μm. This process makes it possible to enhance ARMs’ transmittance in the infrared wavelength range by using direct laser writing in burst mode.

Paper‐based strain sensors (PSS) have broad prospects in disposable products due to their low cost and easy degradation as environmentally friendly materials. Herein, a strain sensor made of a laser‐induced carbonization electrode is created by direct laser writing with filter paper. The conductivity and gauge factor (GF) of this strain sensor are improved by adding lignin and applying strain engineering. This enables the sensor to simultaneously satisfy high sensitivity (GF ≈ 408 and 91) for weak tension and compression strain, respectively, and with long‐term reliability. The tensile strain GF factors of up to 201 are possible, even with a weak tensile strain of 0.00088%. Furthermore, the paper‐based sensor for monitoring physiological activities like finger gestures, pulsing, swallowing, and eye blinking is demonstrated. The facile fabrication and superior performance of PSS fabricated by direct laser writing with strain engineering may pave the way for promising applications of flexible, portable, and wearable electronic devices.

The performance of electrodes is a key factor affecting the development of smart fabrics. The preparation of common fabric flexible electrodes has defects such as high cost, complicated preparation, and complex patterning that limit the development of fabric-based metal electrodes. Therefore, this paper presented a simple fabrication method for preparing Cu electrodes using selective laser reduction of CuO nanoparticles. By optimizing laser processing power, scanning speed, and focusing degree), we prepared a Cu circuit with an electrical resistivity of ∼ 5.53 µΩ.m. Based on the photothermoelectric properties of Cu electrodes, a white light photodetector is developed. The detectivity of the photodetector reaches ∼2.14 mA/W at a power density of 10.01 mW/cm². This method is instructive for preparing metal electrodes or conductive lines on the surface of fabrics, and provides specific techniques for manufacturing wearable photodetectors.