Jianjun Gao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jianjun Gao has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Haibin Geng
School of Mechanical Engineering and Automation, Fuzhou University, 350108, Fu Zhou, People’s Republic of China
10 shared publications - Zhilong Zhao
School of Mechanical Engineering, Northwestern Polytechnical University, Xi’an 710072, China
9 shared publications - Jian Luo
Fuzhou University, Fuzhou University School of Mechanical Engineering and Automation, 2 xueyuan road, university new district, fuzhou district, fuzhou city, Fuzhou, FU Jian, 350002, CHINA
6 shared publications - Kai Cui
School of Mechanical and Power Engineering, Zhengzhou University, Zhengzhou, China
4 shared publications Kai Cui
School of Mechanical Engineering Northwestern Polytechnical University 710072 Xi'an China
3 shared publications- Lin Liu
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China
3 shared publications
Latest Publications
- Open Access
- 1 December 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (12) , 125005
Surface plasmon resonance of the W nanowires
The Surface plasmon resonance (SPR) of metal materials has been widely used in photocatalysis, light sensing, biomarkers, solar cells and other fields. In this study, the surface plasmon characteristics of tungsten (W) nanowires with different diameters and lengths are analyzed using the finite element method. The thermal effect in the gap of crossed nanowires induced by the plasma resonance is studied. Results show that the resonance peak shifts red, and the resonance intensity increases with the increase in diameter. The increasing diameter results in decreasing electric field intensity and heat in the gap of the crossed tungsten (W) nanowires. The frequency of resonance peaks almost remains unchanged with increasing length. The two to six wave belly plasma modes are visible with increasing nanowire length. With exposure to incident light, the SPR in the shortened spacing results in increasing electric field intensity and the generated heat of gap between the two crossed tungsten (W) nanowires. Once the two crossed nanowires are welded, the heat production in the crossed part decreases, which indicates the self-limitation of plasma welding.
- 1 December 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (12) , 125005
Open AccessSurface plasmon resonance of the W nanowires
The Surface plasmon resonance (SPR) of metal materials has been widely used in photocatalysis, light sensing, biomarkers, solar cells and other fields. In this study, the surface plasmon characteristics of tungsten (W) nanowires with different diameters and lengths are analyzed using the finite element method. The thermal effect in the gap of crossed nanowires induced by the plasma resonance is studied. Results show that the resonance peak shifts red, and the resonance intensity increases with the increase in diameter. The increasing diameter results in decreasing electric field intensity and heat in the gap of the crossed tungsten (W) nanowires. The frequency of resonance peaks almost remains unchanged with increasing length. The two to six wave belly plasma modes are visible with increasing nanowire length. With exposure to incident light, the SPR in the shortened spacing results in increasing electric field intensity and the generated heat of gap between the two crossed tungsten (W) nanowires. Once the two crossed nanowires are welded, the heat production in the crossed part decreases, which indicates the self-limitation of plasma welding.
- Open Access
Cu Nanowires and Nanoporous Ag Matrix Fabricated through Directional Solidification and Selective Dissolution of Ag–Cu Eutectic Alloys
Cu nanowires and a nanoporous Ag matrix were fabricated through directional solidification and selective dissolution of Ag–Cu eutectic alloys. Ag-39.9at.%Cu eutectic alloys were directionally solidified at growth rates of 14, 25, and 34 μm/s at a temperature gradient of 10 K/cm. The Cu phase in the Ag matrix gradually changed from lamellar to fibrous with an increase in the growth rate. The Ag matrix phase was selectively dissolved, and Cu nanowires of 300–600 nm in diameter and tens of microns in length were prepared in 0.1 M borate buffer with a pH of 9.18 at a constant potential of 0.7 V (vs. SCE). The nanoporous Ag matrix was fabricated through selective dissolution of Cu fiber phase in 0.1 M acetate buffer with a pH of 6.0 at a constant potential of 0.5 V (vs. SCE). The diameter of Ag pores decreased with increasing growth rate. The diameter and depth of Ag pores increased when corrosion time was extended. The depth of the pores was 30 μm after 12 h.
Open AccessCu Nanowires and Nanoporous Ag Matrix Fabricated through Directional Solidification and Selective Dissolution of Ag–Cu Eutectic Alloys
Cu nanowires and a nanoporous Ag matrix were fabricated through directional solidification and selective dissolution of Ag–Cu eutectic alloys. Ag-39.9at.%Cu eutectic alloys were directionally solidified at growth rates of 14, 25, and 34 μm/s at a temperature gradient of 10 K/cm. The Cu phase in the Ag matrix gradually changed from lamellar to fibrous with an increase in the growth rate. The Ag matrix phase was selectively dissolved, and Cu nanowires of 300–600 nm in diameter and tens of microns in length were prepared in 0.1 M borate buffer with a pH of 9.18 at a constant potential of 0.7 V (vs. SCE). The nanoporous Ag matrix was fabricated through selective dissolution of Cu fiber phase in 0.1 M acetate buffer with a pH of 6.0 at a constant potential of 0.5 V (vs. SCE). The diameter of Ag pores decreased with increasing growth rate. The diameter and depth of Ag pores increased when corrosion time was extended. The depth of the pores was 30 μm after 12 h.
- Open Access
Selective Etching of Sr-Modified and Directionally Solidified Industrial Al–Si Eutectic Alloys for Fabricating Fibrous Eutectic Si
In order to fabricate fibrous eutectic Si, the selective etching of industrial Al–Si eutectic alloys directionally solidified at different growth rates and modified by different amounts of Sr was studied. Flake eutectic and fibrous Si were obtained by selective etching of non-modified, Sr-modified or directionally solidified Al–Si eutectic alloys. The optimal amount of Sr for fabricating branching eutectic Si was 0.04–0.07%. Through directional solidification with a high enough growth rate (more than 200 μm/s), lamellar eutectic Si transforms to fibrous eutectic Si for use in non-modified Al–Si eutectic alloys. The potentiodynamic polarization and cyclic voltammetry methods were used to test the corrosion behavior of non-modified and Sr-modified Al–Si eutectic alloys. With a constant potential of 0.5 V in HCl solution, non-modified Al–Si eutectic alloys displayed initial pitting corrosion and subsequent spalling corrosion, and 0.04% Sr-modified samples displayed uniform pitting corrosion. Compared with non-modified Al–Si eutectic alloys, Sr-modified samples displayed better corrosion resistance with lower current density and shallower pit depth during the same etching conditions.
Open AccessSelective Etching of Sr-Modified and Directionally Solidified Industrial Al–Si Eutectic Alloys for Fabricating Fibrous Eutectic Si
In order to fabricate fibrous eutectic Si, the selective etching of industrial Al–Si eutectic alloys directionally solidified at different growth rates and modified by different amounts of Sr was studied. Flake eutectic and fibrous Si were obtained by selective etching of non-modified, Sr-modified or directionally solidified Al–Si eutectic alloys. The optimal amount of Sr for fabricating branching eutectic Si was 0.04–0.07%. Through directional solidification with a high enough growth rate (more than 200 μm/s), lamellar eutectic Si transforms to fibrous eutectic Si for use in non-modified Al–Si eutectic alloys. The potentiodynamic polarization and cyclic voltammetry methods were used to test the corrosion behavior of non-modified and Sr-modified Al–Si eutectic alloys. With a constant potential of 0.5 V in HCl solution, non-modified Al–Si eutectic alloys displayed initial pitting corrosion and subsequent spalling corrosion, and 0.04% Sr-modified samples displayed uniform pitting corrosion. Compared with non-modified Al–Si eutectic alloys, Sr-modified samples displayed better corrosion resistance with lower current density and shallower pit depth during the same etching conditions.
- Open Access
Morphologies, Young’s Modulus and Resistivity of High Aspect Ratio Tungsten Nanowires
High aspect ratio tungsten nanowires have been prepared by selective dissolution of Nickel-aluminum-tungsten (NiAl−W) alloys which were directionally solidified at growth rates varying from 2 to 25 μm/s with a temperature gradient of 300 K·cm−1. Young’s modulus and electrical resistivity of tungsten nanowires were measured by metallic mask template method. The results show that the tungsten nanowires with uniform diameter and high aspect ratio are well aligned. The length of tungsten nanowires increases with prolongation of etching time, and their length reaches 300 μm at 14 h. Young’s modulus of tungsten nanowires is estimated by Hertz and Sneddon models. The Sneddon model is proper for estimating the Young’s modulus, and the value of calculating Young’s modulus are 260–460 GPa which approach the value of bulk tungsten. The resistivity of tungsten nanowires is measured and fitted with Fuchs−Sondheimer (FS) + Mayadas−Shatzkes (MS) model. The fitting results show that the specific resistivity of W nanowires is a litter bigger than the bulk W, and its value decreases with decreasing diameter.
Open AccessMorphologies, Young’s Modulus and Resistivity of High Aspect Ratio Tungsten Nanowires
High aspect ratio tungsten nanowires have been prepared by selective dissolution of Nickel-aluminum-tungsten (NiAl−W) alloys which were directionally solidified at growth rates varying from 2 to 25 μm/s with a temperature gradient of 300 K·cm−1. Young’s modulus and electrical resistivity of tungsten nanowires were measured by metallic mask template method. The results show that the tungsten nanowires with uniform diameter and high aspect ratio are well aligned. The length of tungsten nanowires increases with prolongation of etching time, and their length reaches 300 μm at 14 h. Young’s modulus of tungsten nanowires is estimated by Hertz and Sneddon models. The Sneddon model is proper for estimating the Young’s modulus, and the value of calculating Young’s modulus are 260–460 GPa which approach the value of bulk tungsten. The resistivity of tungsten nanowires is measured and fitted with Fuchs−Sondheimer (FS) + Mayadas−Shatzkes (MS) model. The fitting results show that the specific resistivity of W nanowires is a litter bigger than the bulk W, and its value decreases with decreasing diameter.
- Open Access
Study on the Relationship between Root Metal Flow Behavior and Root Flaw Formation of a 2024 Aluminum Alloy Joint in Friction Stir Welding by a Multiphysics Field Model
In friction stir welding (FSW), many defects (such as kissing bond, incomplete penetration, and weak connection) easily occur at the root of the welded joint. Based on the Levy–Mises yield criterion of the Zener–Hollomon thermoplastic constitutive equation, a 3D thermal–mechanical coupled finite element model was established. The material flow behavior and the stress field at the root area of a 6 mm thick 2024-T3 aluminum alloy FSW joint were studied. The influence of pin length on the root flaw was investigated, and the formation mechanism of the “S line” defects and non-penetration defects were revealed. The research results showed that the “S line” defect forms near the bottom surface of the pin owing to the insufficiently mixed material from the advancing side (AS) and retreating side (RS) near the weld center. The non-penetration defect forms near the bottom surface of the workpiece owing to the insufficient driving force to make the material flow through the weld center. With the continual increase of pin length, the size of the “S line” defect and non-penetration defect reduces, and finally, the defect-free welded joint can be obtained with an optimized suitable length of the pin in this case.
Open AccessStudy on the Relationship between Root Metal Flow Behavior and Root Flaw Formation of a 2024 Aluminum Alloy Joint in Friction Stir Welding by a Multiphysics Field Model
In friction stir welding (FSW), many defects (such as kissing bond, incomplete penetration, and weak connection) easily occur at the root of the welded joint. Based on the Levy–Mises yield criterion of the Zener–Hollomon thermoplastic constitutive equation, a 3D thermal–mechanical coupled finite element model was established. The material flow behavior and the stress field at the root area of a 6 mm thick 2024-T3 aluminum alloy FSW joint were studied. The influence of pin length on the root flaw was investigated, and the formation mechanism of the “S line” defects and non-penetration defects were revealed. The research results showed that the “S line” defect forms near the bottom surface of the pin owing to the insufficiently mixed material from the advancing side (AS) and retreating side (RS) near the weld center. The non-penetration defect forms near the bottom surface of the workpiece owing to the insufficient driving force to make the material flow through the weld center. With the continual increase of pin length, the size of the “S line” defect and non-penetration defect reduces, and finally, the defect-free welded joint can be obtained with an optimized suitable length of the pin in this case.
- Open Access
Thermal Boundary Evolution of Molten Pool During Wire and Arc Additive Manufacturing of Single Walls of 5A06 Aluminum Alloy
Molten pool uniformity is a prerequisite for wire and arc additive manufacture to achieve a uniform surface appearance. The thermal boundary is a key indicator to evaluate the thermodynamic state of the molten pool. This paper focuses on thermal analysis through finite element simulation and characterizes the thermal evolution of a molten pool during bottom-up deposition. The peak temperature of the substrate plate increases from 375.7 °C to 623.1 °C when peak current increases from 120 A to 180 A. The temperature gradient decreases from 40 °C/mm to 30 °C/mm. Weld speed increases from 0.15 m/min to 0.25 m/min; the temperature gradient is kept at about 30 °C/mm. Dimensionless thermal conductivity, Ge number, is proposed and defined as the criteria to estimate layer size variation. For Ip = 140 A, the average value of the Ge number is 87.7, and it shows the best numerical stability. Dimensionless thermal conductivity, Ge, is proposed and defined as the criteria to estimate the occurrence of layer size variation. Prolonging heating time and increasing cycle frequency, Ge number shows favorable stability during bottom-up deposition. The experimental results are consistent with analytical conclusions, which proves the validity of the Ge number as an indicator of deposition stability.
Open AccessThermal Boundary Evolution of Molten Pool During Wire and Arc Additive Manufacturing of Single Walls of 5A06 Aluminum Alloy
Molten pool uniformity is a prerequisite for wire and arc additive manufacture to achieve a uniform surface appearance. The thermal boundary is a key indicator to evaluate the thermodynamic state of the molten pool. This paper focuses on thermal analysis through finite element simulation and characterizes the thermal evolution of a molten pool during bottom-up deposition. The peak temperature of the substrate plate increases from 375.7 °C to 623.1 °C when peak current increases from 120 A to 180 A. The temperature gradient decreases from 40 °C/mm to 30 °C/mm. Weld speed increases from 0.15 m/min to 0.25 m/min; the temperature gradient is kept at about 30 °C/mm. Dimensionless thermal conductivity, Ge number, is proposed and defined as the criteria to estimate layer size variation. For Ip = 140 A, the average value of the Ge number is 87.7, and it shows the best numerical stability. Dimensionless thermal conductivity, Ge, is proposed and defined as the criteria to estimate the occurrence of layer size variation. Prolonging heating time and increasing cycle frequency, Ge number shows favorable stability during bottom-up deposition. The experimental results are consistent with analytical conclusions, which proves the validity of the Ge number as an indicator of deposition stability.
- Open Access
Theoretical Model of Residual Stress and Warpage for Wire and Arc Additive Manufacturing Stiffened Panels
Wire and arc additive manufacturing of stiffened ribs for fabricating large integral panel components holds promise for lightweight construction, but stress and warpage remain intractable problems. This work take stress in central lines as a research focus, theoretically analyzes stress evolution along central lines without a stress distribution hypothesis, then further develops prediction models of warpage, based on general beam theory. The stress and warpage models are then verified by experimental results. The results showed that below 40 layers, the stress in the top layer increased rapidly to the yield strength. Following the continuous deposition of up to 100 layers, stress increased slowly, then gradually trended to a constant level. After 100 layers of deposition, the top-layer-plane stress in the 10th layer decreased from 68 MPa to 5 MPa, and the plane stress in the 90th layer decreased from 296 MPa to 245 MPa. Post-heating treatment effect was important for temperature uniformity. The largest warpage (3.48 mm) happened when stiffener was designed as 30 layers.
Open AccessTheoretical Model of Residual Stress and Warpage for Wire and Arc Additive Manufacturing Stiffened Panels
Wire and arc additive manufacturing of stiffened ribs for fabricating large integral panel components holds promise for lightweight construction, but stress and warpage remain intractable problems. This work take stress in central lines as a research focus, theoretically analyzes stress evolution along central lines without a stress distribution hypothesis, then further develops prediction models of warpage, based on general beam theory. The stress and warpage models are then verified by experimental results. The results showed that below 40 layers, the stress in the top layer increased rapidly to the yield strength. Following the continuous deposition of up to 100 layers, stress increased slowly, then gradually trended to a constant level. After 100 layers of deposition, the top-layer-plane stress in the 10th layer decreased from 68 MPa to 5 MPa, and the plane stress in the 90th layer decreased from 296 MPa to 245 MPa. Post-heating treatment effect was important for temperature uniformity. The largest warpage (3.48 mm) happened when stiffener was designed as 30 layers.
- Open Access
- 1 May 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (5) , 056514
Analysis on the characteristics of pulsed electromagnetic force and the fluctuation behavior of molten metal free surface under pulsed magnetic field
A self-made line laser liquid level measurement system was used to measure the fluctuation of molten metal free surface under pulsed magnetic field. The electromagnetic characteristics of pulsed electromagnetic force were mathematically analyzed. Results showed that the electromagnetic force presents oscillatory attenuation during a single pulse period. The electromagnetic force was composed of turning force f t u r n and non-turning force f n o n t u r n . The direction of f t u r n was always consistent with the melt circumferential direction, which turned the f n o n t u r n consisted of electromagnetic pull and push forces, which caused the melt to oscillate. Under the pulsed magnetic field, the free surface formed a meniscus with a high middle, low side structure. With increased pulsed field intensity, the center surface of molten melt had an oscillation of ±3.52 mm at 0.187 T. The wave power density had only two spectral peaks (at 0.60 and 3.36 Hz) without a magnetic field. Under pulsed magnetic field, four spectral peaks were found at 0.40, 3.00, 6.50 and 13.00 Hz.
- 1 May 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (5) , 056514
Open AccessAnalysis on the characteristics of pulsed electromagnetic force and the fluctuation behavior of molten metal free surface under pulsed magnetic field
A self-made line laser liquid level measurement system was used to measure the fluctuation of molten metal free surface under pulsed magnetic field. The electromagnetic characteristics of pulsed electromagnetic force were mathematically analyzed. Results showed that the electromagnetic force presents oscillatory attenuation during a single pulse period. The electromagnetic force was composed of turning force f t u r n and non-turning force f n o n t u r n . The direction of f t u r n was always consistent with the melt circumferential direction, which turned the f n o n t u r n consisted of electromagnetic pull and push forces, which caused the melt to oscillate. Under the pulsed magnetic field, the free surface formed a meniscus with a high middle, low side structure. With increased pulsed field intensity, the center surface of molten melt had an oscillation of ±3.52 mm at 0.187 T. The wave power density had only two spectral peaks (at 0.60 and 3.36 Hz) without a magnetic field. Under pulsed magnetic field, four spectral peaks were found at 0.40, 3.00, 6.50 and 13.00 Hz.
- 1 April 2020
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 244, 122594
Coral-flake Co particles electrodeposited into the porous NiAl matrix
- 1 April 2020
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 244, 122594
Coral-flake Co particles electrodeposited into the porous NiAl matrix
- Open Access
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126128
Structure and magnetic properties of ordered coral−globular−like Co particles prepared by electrodeposition
Ordered coral−globular−like cobalt (Co) particles of different sizes and magnetic properties were prepared by electrodeposition. After the passivation of directionally solidified NiAl–W eutectic alloys, W fibers were raised on the surface of NiAl matrix. The Co particles were grown around the protruding W fibers. Cathodic potential experiments indicated that an instantaneous nucleation was generated by the deposition potential of ‒0.8 V. The interspace of Co was consistent with the interspace of W fibers distributed in the NiAl matrix. With increasing deposition time, the diameter and height of Co particles, coercivity H_c, and remanent magnetization M_r increased. Co particles featured a labyrinth domain and their magnetic structures were in multidomain state.
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126128
Open AccessStructure and magnetic properties of ordered coral−globular−like Co particles prepared by electrodeposition
Ordered coral−globular−like cobalt (Co) particles of different sizes and magnetic properties were prepared by electrodeposition. After the passivation of directionally solidified NiAl–W eutectic alloys, W fibers were raised on the surface of NiAl matrix. The Co particles were grown around the protruding W fibers. Cathodic potential experiments indicated that an instantaneous nucleation was generated by the deposition potential of ‒0.8 V. The interspace of Co was consistent with the interspace of W fibers distributed in the NiAl matrix. With increasing deposition time, the diameter and height of Co particles, coercivity H_c, and remanent magnetization M_r increased. Co particles featured a labyrinth domain and their magnetic structures were in multidomain state.