Markku Nikku
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Markku Nikku has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Jouni Ritvanen
Lappeenranta-Lahti University of Technology, LUT School of Energy Systems, P.O. Box 20, FI-53851, Lappeenranta, Finland
6 shared publications - Timo Hyppänen
Lappeenranta University of Technology, Post Office Box 20, FI-53851 Lappeenranta, Finland
5 shared publications - Kari Myöhänen
Lappeenranta University of Technology
4 shared publications - Eero Inkeri
Laboratory of Thermodynamics, LUT University, Lappeenranta, Finland
2 shared publications - Ekaterina Sermyagina
School of Energy Systems, Lappeenranta-Lahti University of Technology LUT, Lappeenranta, Finland
2 shared publications - Markus Secomandi
Lappeenranta-Lahti University of Technology, LUT School of Energy Systems, P.O. Box 20, FI-53851, Lappeenranta, Finland
2 shared publications
Latest Publications
- Open Access
- 21 August 2026
- Published by Elsevier in SSRN Electronic Journal
Dynamic modelling of calcium looping integrated with an electric arc furnace
Electric arc furnaces (EAFs) powered by green electricity enable steel production with significantly lower CO2 emissions than conventional methods. However, small to moderate emissions are unavoidable without carbon capture, utilisation and/or storage (CCUS), as carbon is an essential component of steelmaking. EAF off-gases are highly dynamic, with flow rate, temperature, and composition varying substantially at different stages of production, which makes the design of capture systems challenging. This work investigates the integration of tail-end calcium looping (CaL) for the decarbonisation of EAF off-gases using a 1.5D dynamic reactor model. The results show that carbonator temperature and carbonate accumulation are strongly coupled, as both are governed by the carbonation reaction. This coupling leads to a fundamental trade-off in operation, where increasing the supply of reactive sorbent introduces additional heat, raising the temperature and potentially limiting performance due to equilibrium constraints. Simulations demonstrate that temperature fluctuations exceeding 100 °C may occur under highly dynamic conditions, but can be managed through appropriate control of solids flows. Allowing the carbonator temperature to vary with CO2 concentration is shown to improve capture efficiency compared to strict temperature control. The use of Ca(OH)2 as a supplementary sorbent further enhances capture during CO2 peaks, although utilisation is limited by residence time. A simple linear relationship between temperature and carbonate content is identified, enabling estimation of the thermal response using a simplified model. Overall, the results indicate that CaL can effectively decarbonise dynamic EAF off-gases when thermal and material effects are properly accounted for in process design.
- 21 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDynamic modelling of calcium looping integrated with an electric arc furnace
Electric arc furnaces (EAFs) powered by green electricity enable steel production with significantly lower CO2 emissions than conventional methods. However, small to moderate emissions are unavoidable without carbon capture, utilisation and/or storage (CCUS), as carbon is an essential component of steelmaking. EAF off-gases are highly dynamic, with flow rate, temperature, and composition varying substantially at different stages of production, which makes the design of capture systems challenging. This work investigates the integration of tail-end calcium looping (CaL) for the decarbonisation of EAF off-gases using a 1.5D dynamic reactor model. The results show that carbonator temperature and carbonate accumulation are strongly coupled, as both are governed by the carbonation reaction. This coupling leads to a fundamental trade-off in operation, where increasing the supply of reactive sorbent introduces additional heat, raising the temperature and potentially limiting performance due to equilibrium constraints. Simulations demonstrate that temperature fluctuations exceeding 100 °C may occur under highly dynamic conditions, but can be managed through appropriate control of solids flows. Allowing the carbonator temperature to vary with CO2 concentration is shown to improve capture efficiency compared to strict temperature control. The use of Ca(OH)2 as a supplementary sorbent further enhances capture during CO2 peaks, although utilisation is limited by residence time. A simple linear relationship between temperature and carbonate content is identified, enabling estimation of the thermal response using a simplified model. Overall, the results indicate that CaL can effectively decarbonise dynamic EAF off-gases when thermal and material effects are properly accounted for in process design.
- Open Access
- 6 September 2025
- Published by Elsevier in Particuology
- Vol. 106, 123-130
A novel method for controlling solids circulation between two fluidized bed reactors in a looping system
- 6 September 2025
- Published by Elsevier in Particuology
- Vol. 106, 123-130
Open AccessA novel method for controlling solids circulation between two fluidized bed reactors in a looping system
- Open Access
- 17 July 2025
- Published by Elsevier in Chemical Engineering Science
- Vol. 318
Numerical investigation of the impact of solids flow control on the performance of the calcium looping process
- 17 July 2025
- Published by Elsevier in Chemical Engineering Science
- Vol. 318
Open AccessNumerical investigation of the impact of solids flow control on the performance of the calcium looping process
- Open Access
- 16 December 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 262
Experimental and numerical investigation of a laboratory-scale shell-and-tube latent heat storage
- 16 December 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 262
Open AccessExperimental and numerical investigation of a laboratory-scale shell-and-tube latent heat storage
- Open Access
- 7 March 2023
- Published by Elsevier in Data in Brief
- Vol. 48, 109039
Computational fluid dynamics derived dataset for evaluation of mixing of a secondary solid phase in a circulating fluidized bed riser
- 7 March 2023
- Published by Elsevier in Data in Brief
- Vol. 48, 109039
Open AccessComputational fluid dynamics derived dataset for evaluation of mixing of a secondary solid phase in a circulating fluidized bed riser
- Open Access
- 21 August 2022
- Published by Elsevier in Biomass and Bioenergy
- Vol. 164
Characterization of pellets produced from extracted sawdust: Effect of cooling conditions and binder addition on composition, mechanical and thermochemical properties
- 21 August 2022
- Published by Elsevier in Biomass and Bioenergy
- Vol. 164
Open AccessCharacterization of pellets produced from extracted sawdust: Effect of cooling conditions and binder addition on composition, mechanical and thermochemical properties
- Open Access
- 18 June 2022
- Published by Elsevier in Applied Thermal Engineering
- Vol. 214
Numerical modeling of latent heat thermal energy storage integrated with heat pump for domestic hot water production
- 18 June 2022
- Published by Elsevier in Applied Thermal Engineering
- Vol. 214
Open AccessNumerical modeling of latent heat thermal energy storage integrated with heat pump for domestic hot water production
- Open Access
- 22 September 2021
- Published by Wiley in Engineering Reports
- Vol. 4 (2) , e12460
Effect of software implementation on the result of computational fluid dynamics simulation of circulating fluidized bed risers
While in scientific literature much focus is directed toward model validation, comparison, and even parametric investigations on individual model parameters, the possible effects of the used computational fluid dynamics (CFD) software on the results are largely neglected. In this article, CFD modeling of circulating fluidized beds (CFB) are performed with Ansys Fluent and OpenFOAM to investigate the effect of software implementation on the simulation results. Transient Eulerian–Eulerian simulations are performed of two different laboratory‐scale CFB cold models in turbulent and circulating fluidized bed conditions. The same mesh and as identical models and settings as possible are utilized on both software. The obtained time‐average profiles of pressure, velocity, and solids volume fraction are compared between the software and with available measurements. A difference in the granular energy equation was identified between the software, and a modification was made to achieve the same formulation. The effect of boundary conditions was also investigated. It was found that depending on the case, the software could have a notable effect on the results. These differences are found especially in particle distribution, visible in the vertical pressure and solids volume fraction profiles as well as in external circulation mass flow rates.
- 22 September 2021
- Published by Wiley in Engineering Reports
- Vol. 4 (2) , e12460
Open AccessEffect of software implementation on the result of computational fluid dynamics simulation of circulating fluidized bed risers
While in scientific literature much focus is directed toward model validation, comparison, and even parametric investigations on individual model parameters, the possible effects of the used computational fluid dynamics (CFD) software on the results are largely neglected. In this article, CFD modeling of circulating fluidized beds (CFB) are performed with Ansys Fluent and OpenFOAM to investigate the effect of software implementation on the simulation results. Transient Eulerian–Eulerian simulations are performed of two different laboratory‐scale CFB cold models in turbulent and circulating fluidized bed conditions. The same mesh and as identical models and settings as possible are utilized on both software. The obtained time‐average profiles of pressure, velocity, and solids volume fraction are compared between the software and with available measurements. A difference in the granular energy equation was identified between the software, and a modification was made to achieve the same formulation. The effect of boundary conditions was also investigated. It was found that depending on the case, the software could have a notable effect on the results. These differences are found especially in particle distribution, visible in the vertical pressure and solids volume fraction profiles as well as in external circulation mass flow rates.
- Open Access
- 1 July 2021
- Published by Elsevier in Biomass and Bioenergy
- Vol. 150
Spent coffee grounds and tea leaf residues: Characterization, evaluation of thermal reactivity and recovery of high-value compounds
- 1 July 2021
- Published by Elsevier in Biomass and Bioenergy
- Vol. 150
Open AccessSpent coffee grounds and tea leaf residues: Characterization, evaluation of thermal reactivity and recovery of high-value compounds