Li-Jing Cheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Li-Jing Cheng has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
Ahasan Ullah
School of Electrical Engineering and Computer Science Oregon State University Corvallis Oregon USA
11 shared publicationsBo Wu
School of Electrical Engineering and Computer Science, Oregon State University, Corvallis, Oregon 97331, United States
11 shared publicationsSanjida Yeasmin
School of Electrical Engineering and Computer Science, Oregon State University, 1148 Kelley Engineering Center, Corvallis, Oregon 97331, United States
11 shared publicationsYe Liu
School of Electrical Engineering and Computer Science, Oregon State University, Corvallis, Oregon 97331, USA
11 shared publicationsXueqiao Zhang
School of Electrical Engineering and Computer Science Oregon State University Corvallis Oregon USA
10 shared publicationsAkash Kannegulla
School of Electrical Engineering and Computer Science, Oregon State University, Corvallis, OR, 97331, USA
6 shared publications
Latest Publications
- 19 May 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (56)
Neuromodulator‐Inspired Gate‐Tunable Tetracene–Metal Oxide Phototransistor for Adaptive Optoelectronic Memory and Neuromorphic Computing
We present a neuromodulator‐inspired organic–inorganic hybrid phototransistor that enables programmable optoelectronic memory and synaptic plasticity via dual optical–electrical modulation. The device integrates a tetracene‐based photoactive polymer blend with an indium gallium zinc oxide (IGZO) thin‐film transistor, forming a type‐II heterojunction where photogenerated electrons transfer to the IGZO channel while holes are stored in deep trap states within the organic layer. These trapped charges induce persistent photogating, modulating channel conductance analogous to synaptic potentiation. Trap‐dynamics modeling reveals that deep traps govern long‐term retention, whereas shallow traps allow rapid adaptation. Gate bias further reshapes the trapped‐charge distribution and tunes trapping–detrapping kinetics, achieving programmable transitions between short‐term plasticity and long‐term memory. Negative gate bias reinforces conductance retention (dopamine‐like potentiation), whereas positive bias accelerates relaxation (serotonin‐like depression), enabling polarity‐controlled switching between analog learning, long‐term storage, and controlled forgetting. Operating below 5 µW·cm −2 , the device supports weak‐light imaging (0.5 µW·cm −2 ), memory retention beyond 5000 s, and spatiotemporal trajectory tracking via transient charge storage. A device‐calibrated artificial neural network using differential synapse pairs achieves >90% MNIST classification accuracy with near‐linear weight updates over hundreds of cycles. These results demonstrate an energy‐efficient platform unifying sensing, memory, and computation for neuromodulator‐inspired in‐sensor neuromorphic processing.
- 19 May 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (56)
Neuromodulator‐Inspired Gate‐Tunable Tetracene–Metal Oxide Phototransistor for Adaptive Optoelectronic Memory and Neuromorphic Computing
We present a neuromodulator‐inspired organic–inorganic hybrid phototransistor that enables programmable optoelectronic memory and synaptic plasticity via dual optical–electrical modulation. The device integrates a tetracene‐based photoactive polymer blend with an indium gallium zinc oxide (IGZO) thin‐film transistor, forming a type‐II heterojunction where photogenerated electrons transfer to the IGZO channel while holes are stored in deep trap states within the organic layer. These trapped charges induce persistent photogating, modulating channel conductance analogous to synaptic potentiation. Trap‐dynamics modeling reveals that deep traps govern long‐term retention, whereas shallow traps allow rapid adaptation. Gate bias further reshapes the trapped‐charge distribution and tunes trapping–detrapping kinetics, achieving programmable transitions between short‐term plasticity and long‐term memory. Negative gate bias reinforces conductance retention (dopamine‐like potentiation), whereas positive bias accelerates relaxation (serotonin‐like depression), enabling polarity‐controlled switching between analog learning, long‐term storage, and controlled forgetting. Operating below 5 µW·cm −2 , the device supports weak‐light imaging (0.5 µW·cm −2 ), memory retention beyond 5000 s, and spatiotemporal trajectory tracking via transient charge storage. A device‐calibrated artificial neural network using differential synapse pairs achieves >90% MNIST classification accuracy with near‐linear weight updates over hundreds of cycles. These results demonstrate an energy‐efficient platform unifying sensing, memory, and computation for neuromodulator‐inspired in‐sensor neuromorphic processing.
- 15 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. PP (2156342X) , 1-20
Manipulating Terahertz Waves Using Light for Tunable and Reconfigurable Terahertz Devices
Tunable and reconfigurable devices for efficiently manipulating THz waves in advanced sensing, imaging and communication are challenging to realize. An especially promising approach for developing this class of THz devices–based on spatially-resolved photoconductivity modulation (SRPM) in semiconductors–will be introduced, followed by prototype demonstrations. The SRPM concept can be further enhanced by using mesa-array structures to achieve higher modulation depth and improved spatial resolution for more advanced tunable and reconfigurable THz devices. High-performance THz optically-controlled switches (OCSs) enabling next-generation adaptive integrated THz circuits/systems will then be discussed, and their use for achieving reconfigurable THz filters will also be presented. Finally, in addition to amplitude modulation, a unique approach for achieving high-performance THz phase shifting will be described. In total, the SRPM concept provides a critical solution that enables complete, systematic, and versatile technology for manipulating THz waves across a wide range of applications.
- 15 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. PP (2156342X) , 1-20
Manipulating Terahertz Waves Using Light for Tunable and Reconfigurable Terahertz Devices
Tunable and reconfigurable devices for efficiently manipulating THz waves in advanced sensing, imaging and communication are challenging to realize. An especially promising approach for developing this class of THz devices–based on spatially-resolved photoconductivity modulation (SRPM) in semiconductors–will be introduced, followed by prototype demonstrations. The SRPM concept can be further enhanced by using mesa-array structures to achieve higher modulation depth and improved spatial resolution for more advanced tunable and reconfigurable THz devices. High-performance THz optically-controlled switches (OCSs) enabling next-generation adaptive integrated THz circuits/systems will then be discussed, and their use for achieving reconfigurable THz filters will also be presented. Finally, in addition to amplitude modulation, a unique approach for achieving high-performance THz phase shifting will be described. In total, the SRPM concept provides a critical solution that enables complete, systematic, and versatile technology for manipulating THz waves across a wide range of applications.
- Top Cited PapersOpen Access
- 9 March 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 14 (17) , 7150-7160
Trap-mediated photogating in hybrid organic–inorganic heterojunction phototransistors for photo-memory and photodetection
Trap-mediated photocarrier dynamics govern transient responses in hybrid phototransistors. TES-ADT/IGZO heterojunction shows fast photodetection, while TIPS-Tc/IGZO exhibits gate-controlled trap redistribution for programmable memory and forgetting.
- 9 March 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 14 (17) , 7150-7160
Top Cited PapersOpen AccessTrap-mediated photogating in hybrid organic–inorganic heterojunction phototransistors for photo-memory and photodetection
Trap-mediated photocarrier dynamics govern transient responses in hybrid phototransistors. TES-ADT/IGZO heterojunction shows fast photodetection, while TIPS-Tc/IGZO exhibits gate-controlled trap redistribution for programmable memory and forgetting.
- 10 September 2025
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry Letters
- Vol. 16 (37) , 9806-9814
Dissecting the Large Stokes Shift Fluorescence of Graphene-Sheet-Based Carbon Dots by Excitation-Dependent Ultrafast Spectroscopy
Carbon dots (CDs) represent a new class of nontoxic and sustainable nanomaterials with increasing applications. Among them, bright and large Stokes-shift CDs are highly desirable for display and imaging, yet the emission mechanisms remain unclear. We obtained structural signatures for the recently engineered green and red CDs by ground-state femtosecond stimulated Raman spectroscopy (FSRS), then synthesized orange CDs with similar size but much higher nitrogen dopants than red CDs. We implemented femtosecond transient absorption (fs-TA) spectroscopy to capture charge transfer (CT) from the core/edge to surface states on the ∼450 fs time scale via an ultrafast excited-state absorption (ESA) band shift, confirmed by solvent-dependent studies. Subsequently, optical and acoustic phonons contribute to edge-state dynamics after 400 nm excitation, whereas optical phonons become prominent after 500 and 267 nm excitations, unveiling an interplay among the excitation region, exciton-phonon coupling, and energy dissipation. Global analysis and probe-dependent fits corroborate key excited-state dynamics for large-Stokes-shift emissions, revealing a characteristic relaxation pathway toward an excitation-independent single emissive state at surface. These insights enable a bottom-up approach to rationally design and optimize nitrogen-doped CDs for redder and brighter emissions.
- 10 September 2025
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry Letters
- Vol. 16 (37) , 9806-9814
Dissecting the Large Stokes Shift Fluorescence of Graphene-Sheet-Based Carbon Dots by Excitation-Dependent Ultrafast Spectroscopy
Carbon dots (CDs) represent a new class of nontoxic and sustainable nanomaterials with increasing applications. Among them, bright and large Stokes-shift CDs are highly desirable for display and imaging, yet the emission mechanisms remain unclear. We obtained structural signatures for the recently engineered green and red CDs by ground-state femtosecond stimulated Raman spectroscopy (FSRS), then synthesized orange CDs with similar size but much higher nitrogen dopants than red CDs. We implemented femtosecond transient absorption (fs-TA) spectroscopy to capture charge transfer (CT) from the core/edge to surface states on the ∼450 fs time scale via an ultrafast excited-state absorption (ESA) band shift, confirmed by solvent-dependent studies. Subsequently, optical and acoustic phonons contribute to edge-state dynamics after 400 nm excitation, whereas optical phonons become prominent after 500 and 267 nm excitations, unveiling an interplay among the excitation region, exciton-phonon coupling, and energy dissipation. Global analysis and probe-dependent fits corroborate key excited-state dynamics for large-Stokes-shift emissions, revealing a characteristic relaxation pathway toward an excitation-independent single emissive state at surface. These insights enable a bottom-up approach to rationally design and optimize nitrogen-doped CDs for redder and brighter emissions.
- 2 April 2025
- Published by Wiley in Advanced Optical Materials
- Vol. 13 (16)
Highly Sensitive and Fast‐Response Hybrid Phototransistors Enabled by Dynamic Photogating in Anthradithiophene‐Metal Oxide Heterojunctions
This study presents a high‐performance organic–inorganic hybrid phototransistor featuring a heterojunction formed by photoactive anthradithiophene (ADT) derivatives and a bottom‐gate indium gallium zinc oxide (IGZO) thin‐film transistor (TFT). Two ADT derivatives with silicon‐ or germanium‐containing side chains are explored for device development. The band alignment at the heterojunction facilitates efficient electron transfer and accumulation of photogenerated holes in ADT, driving a photogating effect to modulate IGZO conductivity. Unlike conventional photogating, mediated by carrier trapping with inherently slow response speeds, this device uses trap‐suppressed ADT, achieved through blending with nonconductive polymers, to enable high‐speed photogating. An optimized negative gate voltage creates a synergistic effect, driving the IGZO TFT into a partially depleted subthreshold state and significantly enhancing detectivity and sensing current. Photoluminescence and wavelength‐dependent photoresponse confirm charge transfer between ADT and IGZO, identifying the photoinduced threshold voltage shift as the key mechanism for improved performance. Simulations further elucidate the photodetection process under varying conditions. The phototransistor achieves a linear dynamic range over 100 dB, responsivity of up to 2.80 A W −1 , detectivity exceeding 10 13 Jones, and rapid response with <4 ms rise and <10 ms fall times. These characteristics make it highly suitable for machine vision and low‐power photosensor applications.
- 2 April 2025
- Published by Wiley in Advanced Optical Materials
- Vol. 13 (16)
Highly Sensitive and Fast‐Response Hybrid Phototransistors Enabled by Dynamic Photogating in Anthradithiophene‐Metal Oxide Heterojunctions
This study presents a high‐performance organic–inorganic hybrid phototransistor featuring a heterojunction formed by photoactive anthradithiophene (ADT) derivatives and a bottom‐gate indium gallium zinc oxide (IGZO) thin‐film transistor (TFT). Two ADT derivatives with silicon‐ or germanium‐containing side chains are explored for device development. The band alignment at the heterojunction facilitates efficient electron transfer and accumulation of photogenerated holes in ADT, driving a photogating effect to modulate IGZO conductivity. Unlike conventional photogating, mediated by carrier trapping with inherently slow response speeds, this device uses trap‐suppressed ADT, achieved through blending with nonconductive polymers, to enable high‐speed photogating. An optimized negative gate voltage creates a synergistic effect, driving the IGZO TFT into a partially depleted subthreshold state and significantly enhancing detectivity and sensing current. Photoluminescence and wavelength‐dependent photoresponse confirm charge transfer between ADT and IGZO, identifying the photoinduced threshold voltage shift as the key mechanism for improved performance. Simulations further elucidate the photodetection process under varying conditions. The phototransistor achieves a linear dynamic range over 100 dB, responsivity of up to 2.80 A W −1 , detectivity exceeding 10 13 Jones, and rapid response with <4 ms rise and <10 ms fall times. These characteristics make it highly suitable for machine vision and low‐power photosensor applications.
- 15 October 2024
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 6 (11) , 8163-8170
Fast-Switching Electrochromic Device Enabled by Fe2+-Mediated MnO2/Mn2+ Redox Reactions
- 15 October 2024
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 6 (11) , 8163-8170
Fast-Switching Electrochromic Device Enabled by Fe2+-Mediated MnO2/Mn2+ Redox Reactions
- 1 May 2024
- Published by AIP Publishing in Biomicrofluidics
- Vol. 18 (3)
Emerging trends in functional molecularly imprinted polymers for electrochemical detection of biomarkers
Molecularly imprinted polymers (MIPs), functioning as artificial bioreceptors, hold significant promise for biomarker detection in healthcare, disease diagnosis, and addressing drug abuse. In contrast to natural bioreceptors, MIP-based sensors offer numerous advantages, such as high stability, cost-effectiveness, high selectivity, sensitivity, and notably straightforward preparation with customizable binding sites for diverse targets. Conventional MIP sensors often necessitate external redox reagents in analytes to transduce binding events into electrochemical signals for indirect detection, presenting challenges for practical applications in wearables or point-of-care (POC) testing. Redox-active MIP sensors have emerged as a viable alternative, enabling direct and label-free electrochemical detection, with two types developed. The first type utilizes electrocatalytic materials to expedite electron transfer and facilitate a redox reaction between the captured electroactive target and the electrode. The second type incorporates an embedded redox reactive component that allows selective binding of a target to modulate its electron transfer, leading to a change in the electrical signal. This review covers emerging trends and challenges in redox-active MIP sensors for direct electrochemical detection of biomarkers, focusing on sensing mechanisms, synthesis methods, and applications. Additionally, recent progress in wearable and POC redox-active MIP sensors is highlighted. A comprehensive outlook of challenges is further provided, aiming to advance direct biomarker detection for diverse healthcare applications.
- 1 May 2024
- Published by AIP Publishing in Biomicrofluidics
- Vol. 18 (3)
Emerging trends in functional molecularly imprinted polymers for electrochemical detection of biomarkers
Molecularly imprinted polymers (MIPs), functioning as artificial bioreceptors, hold significant promise for biomarker detection in healthcare, disease diagnosis, and addressing drug abuse. In contrast to natural bioreceptors, MIP-based sensors offer numerous advantages, such as high stability, cost-effectiveness, high selectivity, sensitivity, and notably straightforward preparation with customizable binding sites for diverse targets. Conventional MIP sensors often necessitate external redox reagents in analytes to transduce binding events into electrochemical signals for indirect detection, presenting challenges for practical applications in wearables or point-of-care (POC) testing. Redox-active MIP sensors have emerged as a viable alternative, enabling direct and label-free electrochemical detection, with two types developed. The first type utilizes electrocatalytic materials to expedite electron transfer and facilitate a redox reaction between the captured electroactive target and the electrode. The second type incorporates an embedded redox reactive component that allows selective binding of a target to modulate its electron transfer, leading to a change in the electrical signal. This review covers emerging trends and challenges in redox-active MIP sensors for direct electrochemical detection of biomarkers, focusing on sensing mechanisms, synthesis methods, and applications. Additionally, recent progress in wearable and POC redox-active MIP sensors is highlighted. A comprehensive outlook of challenges is further provided, aiming to advance direct biomarker detection for diverse healthcare applications.
- 18 October 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (43) , 50034-50046
Hybrid Functional Polymer-Enabled Multiplexed Chemosensor Patch for Wearable Adrenocortex Stress Profiling
Measuring bioactive stress hormones, including cortisol and dehydroepiandrosterone (DHEA), allows for evaluating the hypothalamic-pituitary-adrenal (HPA) axis functioning, offering valuable insights into an individual's stress response through adrenocortex stress profiles (ASPs). Conventional methods for detecting steroid hormones involve sample collections and competitive immunoassays, which suffer from drawbacks such as time-consuming labeling and binding procedures, reliance on unstable biological receptors, and the need for sophisticated instruments. Here, we report a label-free and external redox reagent-free amperometric assay directly detecting sweat cortisol and DHEA levels on the skin. The approach utilizes multitarget sensors based on redox-active molecularly imprinted polymers (redox MIPs) capable of selectively binding cortisol and DHEA, inducing changes in electrochemical redox features. The redox MIP consists of imprinted cavities for specific capture of cortisol or DHEA in a poly(pyrrole-co-(dimethylamino)pyrrole) copolymer containing hydrophobic moieties to enhance affinity toward steroid hormones. The polymer matrix also incorporates covalently linked interpenetrating redox-active polyvinylferrocene, offering a stable electrochemical redox feature that enables sensitive current change in response to the target capture in the vicinity. The multiplexed sensor detects cortisol and DHEA within 5 min, with detection limits of 115 and 390 pM, respectively. Through the integration of redox MIP sensors into a wireless wearable sensing system, we successfully achieved ambulatory detection of these two steroid hormones in sweat directly on the skin. The new sensing method facilitates rapid, robust determination of the cortisol-DHEA ratio, providing a promising avenue for point-of-care assessment of an individual's physiological state.
- 18 October 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (43) , 50034-50046
Hybrid Functional Polymer-Enabled Multiplexed Chemosensor Patch for Wearable Adrenocortex Stress Profiling
Measuring bioactive stress hormones, including cortisol and dehydroepiandrosterone (DHEA), allows for evaluating the hypothalamic-pituitary-adrenal (HPA) axis functioning, offering valuable insights into an individual's stress response through adrenocortex stress profiles (ASPs). Conventional methods for detecting steroid hormones involve sample collections and competitive immunoassays, which suffer from drawbacks such as time-consuming labeling and binding procedures, reliance on unstable biological receptors, and the need for sophisticated instruments. Here, we report a label-free and external redox reagent-free amperometric assay directly detecting sweat cortisol and DHEA levels on the skin. The approach utilizes multitarget sensors based on redox-active molecularly imprinted polymers (redox MIPs) capable of selectively binding cortisol and DHEA, inducing changes in electrochemical redox features. The redox MIP consists of imprinted cavities for specific capture of cortisol or DHEA in a poly(pyrrole-co-(dimethylamino)pyrrole) copolymer containing hydrophobic moieties to enhance affinity toward steroid hormones. The polymer matrix also incorporates covalently linked interpenetrating redox-active polyvinylferrocene, offering a stable electrochemical redox feature that enables sensitive current change in response to the target capture in the vicinity. The multiplexed sensor detects cortisol and DHEA within 5 min, with detection limits of 115 and 390 pM, respectively. Through the integration of redox MIP sensors into a wireless wearable sensing system, we successfully achieved ambulatory detection of these two steroid hormones in sweat directly on the skin. The new sensing method facilitates rapid, robust determination of the cortisol-DHEA ratio, providing a promising avenue for point-of-care assessment of an individual's physiological state.
- 27 July 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 11 (34) , 11476-11485
Highly fluorescent nitrogen-doped carbon dots with large Stokes shifts
We present highly fluorescent red and green carbon dots (CDs) with remarkable Stokes shifts of 216 and 140 nm, respectively, due to the surface-state emission. Printable inks are demonstrated with CD patterns for color-conversion LEDs and display.
- 27 July 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 11 (34) , 11476-11485
Highly fluorescent nitrogen-doped carbon dots with large Stokes shifts
We present highly fluorescent red and green carbon dots (CDs) with remarkable Stokes shifts of 216 and 140 nm, respectively, due to the surface-state emission. Printable inks are demonstrated with CD patterns for color-conversion LEDs and display.
- 12 March 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (11) , 13971-13982
Enzyme-Mimics for Sensitive and Selective Steroid Metabolite Detection
We present an enzyme-like functional polymer that recognizes nonelectroactive targets and catalyzes their redox reactions for simple, selective steroid metabolite detection. Measuring steroid metabolites, such as cortisol, has been widely adopted to diagnose stress and chronic diseases. Conventional detection method based on competitive immunoassay requires time-consuming labeling processes for signal transduction and unstable biological receptors for biorecognition yet with limited selectivity. Inspired by natural enzymes' target specificity and catalytic nature, we report an enzyme-mimic using electrocatalytic molecularly imprinted polymers (EC-MIP) to achieve label-free, external redox reagent-free, sensitive, and selective electrochemical detection of cortisol. The EC-MIP sensor contains molecularly imprinted cavities for specific cortisol binding and embedded copper phthalocyanine tetrasulfonate (CuPcTS) for electrocatalytic reduction of the ketones on the captured cortisol into alcohols. The direct sensing approach resolves the intrinsic limitations of conventional MIP-based sensors, most notably the use of external redox probes and weak sensing signals. The sensor exhibited a detection limit of 181 pM with significantly enhanced selectivity using a differential sensing mechanism. The new enzyme-like sensor can be modified to detect other targets, offering a simple, robust approach to future health monitoring technologies.
- 12 March 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (11) , 13971-13982
Enzyme-Mimics for Sensitive and Selective Steroid Metabolite Detection
We present an enzyme-like functional polymer that recognizes nonelectroactive targets and catalyzes their redox reactions for simple, selective steroid metabolite detection. Measuring steroid metabolites, such as cortisol, has been widely adopted to diagnose stress and chronic diseases. Conventional detection method based on competitive immunoassay requires time-consuming labeling processes for signal transduction and unstable biological receptors for biorecognition yet with limited selectivity. Inspired by natural enzymes' target specificity and catalytic nature, we report an enzyme-mimic using electrocatalytic molecularly imprinted polymers (EC-MIP) to achieve label-free, external redox reagent-free, sensitive, and selective electrochemical detection of cortisol. The EC-MIP sensor contains molecularly imprinted cavities for specific cortisol binding and embedded copper phthalocyanine tetrasulfonate (CuPcTS) for electrocatalytic reduction of the ketones on the captured cortisol into alcohols. The direct sensing approach resolves the intrinsic limitations of conventional MIP-based sensors, most notably the use of external redox probes and weak sensing signals. The sensor exhibited a detection limit of 181 pM with significantly enhanced selectivity using a differential sensing mechanism. The new enzyme-like sensor can be modified to detect other targets, offering a simple, robust approach to future health monitoring technologies.