Jennifer B. Sharpe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Interests
Jennifer B. Sharpe has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
David T. Soong
7 shared publicationsElizabeth A. Murphy
5 shared publications- Thomas M. Over
Central Midwest Water Science Center, U.S. Geological Survey, Urbana, IL 61801, USA
3 shared publications - Amy M. Gahala2 shared publications
Audrey L. Ishii
2 shared publicationsCharles F. Avery
2 shared publications
Latest Publications
- Open Access
- 1 January 2024
- Published by US Geological Survey
Simulation of groundwater and surface-water interaction and lake resiliency at Crystal Lake, City of Crystal Lake, Illinois
The U.S. Geological Survey, in cooperation with the City of Crystal Lake, Illinois, started a study to increase understanding of groundwater and surface-water interaction between the glacial aquifer and the city’s namesake lake, Crystal Lake, and the effect of higher and lower precipitation conditions on groundwater and lake levels. The results from this study could be used by the city and others to aid in lake management strategies. This report describes the hydrologic lake budget and each of the budget components, which are then used in the construction, calibration, and application of a regional groundwater flow model. The flow model is used to simulate the shallow groundwater flow system and the lake responses to increased and decreased precipitation under the current weir elevation and the proposed lowered weir elevation.Using the program groundwater flow analytic element model (GFLOW), a two-dimensional, steady-state model was constructed. The model was calibrated by matching target water levels and stream base flows by adjusting model input parameters. A sensitivity analysis was completed by adjusting the parameters within reasonable ranges and noting the magnitude of changes in model calibration targets. Potential effects of extended wet and dry periods (within historical ranges and published predicted ranges) were evaluated by adjusting precipitation, groundwater recharge, and discharge at Crystal Lake culvert outlet in the model and comparing the resulting simulated lake stage and water budgets to stages and water budgets from the calibrated model.Model results under average, wet, and dry conditions with a lowered weir of 1 foot at the Crystal Lake culvert outlet indicate minor changes in the simulated lake-water budgets and associated lake levels and groundwater elevation contours; however, simulations with an increased outflow at the Crystal Lake culvert outlet decreased the lake water levels by as much as 1.87 feet and also decreased the groundwater levels surrounding the lake by about 1–2 feet during average and wet conditions.
- 1 January 2024
- Published by US Geological Survey
Open AccessSimulation of groundwater and surface-water interaction and lake resiliency at Crystal Lake, City of Crystal Lake, Illinois
The U.S. Geological Survey, in cooperation with the City of Crystal Lake, Illinois, started a study to increase understanding of groundwater and surface-water interaction between the glacial aquifer and the city’s namesake lake, Crystal Lake, and the effect of higher and lower precipitation conditions on groundwater and lake levels. The results from this study could be used by the city and others to aid in lake management strategies. This report describes the hydrologic lake budget and each of the budget components, which are then used in the construction, calibration, and application of a regional groundwater flow model. The flow model is used to simulate the shallow groundwater flow system and the lake responses to increased and decreased precipitation under the current weir elevation and the proposed lowered weir elevation.Using the program groundwater flow analytic element model (GFLOW), a two-dimensional, steady-state model was constructed. The model was calibrated by matching target water levels and stream base flows by adjusting model input parameters. A sensitivity analysis was completed by adjusting the parameters within reasonable ranges and noting the magnitude of changes in model calibration targets. Potential effects of extended wet and dry periods (within historical ranges and published predicted ranges) were evaluated by adjusting precipitation, groundwater recharge, and discharge at Crystal Lake culvert outlet in the model and comparing the resulting simulated lake stage and water budgets to stages and water budgets from the calibrated model.Model results under average, wet, and dry conditions with a lowered weir of 1 foot at the Crystal Lake culvert outlet indicate minor changes in the simulated lake-water budgets and associated lake levels and groundwater elevation contours; however, simulations with an increased outflow at the Crystal Lake culvert outlet decreased the lake water levels by as much as 1.87 feet and also decreased the groundwater levels surrounding the lake by about 1–2 feet during average and wet conditions.
- Open Access
- 1 January 2023
- Published by US Geological Survey
Statewide sampling to determine spatial distribution, prevalence, and occurrence of per- and polyfluoroalkyl substances (PFAS) in Illinois community water supplies, 2020–21
Per- and polyfluoroalkyl substances (PFAS) are a group of synthetic chemicals that have been manufactured and used globally since the 1940s. PFAS are used for their oil- and water-repellent properties, ability to reduce friction, and their flame-retardant nature. PFAS are widely used in a variety of products, including clothing, carpet, food packaging, and firefighting foam. The properties that make them useful in manufacturing, however, also make them persistent and mobile, causing potential exposures to the environment and humans. Known as “forever chemicals,” these compounds resist degradation and have been determined to bioaccumulate in humans and wildlife.The Illinois Environmental Protection Agency (IEPA) collected a total of 1,711 samples (includes quality-control samples) of finished water at 1,428 entry points from 1,017 Illinois community water supply (CWS) systems and analyzed the water samples for PFAS. The results following confirmation samples indicated a mean of 99 percent of all sample results were below the minimum reporting level (MRL) of 2 nanograms per liter (ng/L). Of the detections at or above the MRL, 7 of 18 PFAS were detected in 149 of 1,428 entry points (about 10 percent). Of the nearly 7.4 million residents directly served by the CWS systems sampled, more than 1.3 million residents (about 18 percent) are served by CWS systems that had at least one detection of PFAS above the MRL of 2 ng/L. The most frequently detected PFAS were perfluorobutanesulfonic acid (about 6.2 percent, 37 ng/L maximum concentration), perfluorooctanesulfonic acid (PFOS) (about 5.0 percent, 150 ng/L maximum concentration), and perfluorooctanoic acid (PFOA) (about 4.8 percent, 25 ng/L maximum concentration). Of the 1,428 entry point samples from the CWS systems, 149 samples had confirmed detections of PFAS, with 93 of those 149 (about 62 percent) samples having at least one PFAS with a concentration that exceeded the median detected concentration of 3.2 ng/L. The highest concentrations detected were 150 ng/L (PFOS) and 140 ng/L (perfluorohexanesulfonic acid) at one CWS location which has been shut down and a different source of water has been provided to the consumers.Although PFAS detections were more common in CWS systems using surface-water sources (about 35 percent, 30 of 85) and mixed sources (50 percent, 5 of 10) compared to those using groundwater sources (about 9 percent, 114 of 1,333), a greater range of PFAS concentrations were observed in groundwater CWS systems (2 to 150 ng/L) than in surface-water CWS systems (2 to 15 ng/L). Statistically significant differences were determined between some detected PFAS (PFOA, PFOS, and perfluorohexanoic acid) and the source of drinking water (groundwater, surface water, or mixed).This report summarizes the occurrence and spatial distribution of PFAS in CWS systems across Illinois. The results from this sampling effort could be used by Illinois public health officials to identify the potential risk of PFAS in drinking water to human health.
- 1 January 2023
- Published by US Geological Survey
Open AccessStatewide sampling to determine spatial distribution, prevalence, and occurrence of per- and polyfluoroalkyl substances (PFAS) in Illinois community water supplies, 2020–21
Per- and polyfluoroalkyl substances (PFAS) are a group of synthetic chemicals that have been manufactured and used globally since the 1940s. PFAS are used for their oil- and water-repellent properties, ability to reduce friction, and their flame-retardant nature. PFAS are widely used in a variety of products, including clothing, carpet, food packaging, and firefighting foam. The properties that make them useful in manufacturing, however, also make them persistent and mobile, causing potential exposures to the environment and humans. Known as “forever chemicals,” these compounds resist degradation and have been determined to bioaccumulate in humans and wildlife.The Illinois Environmental Protection Agency (IEPA) collected a total of 1,711 samples (includes quality-control samples) of finished water at 1,428 entry points from 1,017 Illinois community water supply (CWS) systems and analyzed the water samples for PFAS. The results following confirmation samples indicated a mean of 99 percent of all sample results were below the minimum reporting level (MRL) of 2 nanograms per liter (ng/L). Of the detections at or above the MRL, 7 of 18 PFAS were detected in 149 of 1,428 entry points (about 10 percent). Of the nearly 7.4 million residents directly served by the CWS systems sampled, more than 1.3 million residents (about 18 percent) are served by CWS systems that had at least one detection of PFAS above the MRL of 2 ng/L. The most frequently detected PFAS were perfluorobutanesulfonic acid (about 6.2 percent, 37 ng/L maximum concentration), perfluorooctanesulfonic acid (PFOS) (about 5.0 percent, 150 ng/L maximum concentration), and perfluorooctanoic acid (PFOA) (about 4.8 percent, 25 ng/L maximum concentration). Of the 1,428 entry point samples from the CWS systems, 149 samples had confirmed detections of PFAS, with 93 of those 149 (about 62 percent) samples having at least one PFAS with a concentration that exceeded the median detected concentration of 3.2 ng/L. The highest concentrations detected were 150 ng/L (PFOS) and 140 ng/L (perfluorohexanesulfonic acid) at one CWS location which has been shut down and a different source of water has been provided to the consumers.Although PFAS detections were more common in CWS systems using surface-water sources (about 35 percent, 30 of 85) and mixed sources (50 percent, 5 of 10) compared to those using groundwater sources (about 9 percent, 114 of 1,333), a greater range of PFAS concentrations were observed in groundwater CWS systems (2 to 150 ng/L) than in surface-water CWS systems (2 to 15 ng/L). Statistically significant differences were determined between some detected PFAS (PFOA, PFOS, and perfluorohexanoic acid) and the source of drinking water (groundwater, surface water, or mixed).This report summarizes the occurrence and spatial distribution of PFAS in CWS systems across Illinois. The results from this sampling effort could be used by Illinois public health officials to identify the potential risk of PFAS in drinking water to human health.
- 1 January 2019
- Published by US Geological Survey
Bathymetric map and surface area and capacity table for Beaver Lake near Rogers, Arkansas, 2018
Beaver Lake was constructed in 1966 on the White River in the northwest corner of Arkansas for flood control, hydroelectric power, public water supply, and recreation. The surface area of Beaver Lake is about 27,900 acres and approximately 449 miles of shoreline are at the conservation pool level (1,120 feet above the North American Vertical Datum of 1988). Sedimentation in reservoirs can result in reduced water storage capacity and a reduction in usable aquatic habitat. Therefore, accurate and up-to-date estimates of reservoir water capacity are important for managing pool levels, power generation, recreation, and downstream aquatic habitat. Many of the lakes operated by the U.S. Army Corps of Engineers are periodically surveyed to monitor bathymetric changes that affect water capacity. In October 2018, the U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, completed one such survey of Beaver Lake using a multibeam echosounder. The echosounder data were combined with light detection and ranging (lidar) data to prepare a bathymetric map and a surface area and capacity table.
- 1 January 2019
- Published by US Geological Survey
Bathymetric map and surface area and capacity table for Beaver Lake near Rogers, Arkansas, 2018
Beaver Lake was constructed in 1966 on the White River in the northwest corner of Arkansas for flood control, hydroelectric power, public water supply, and recreation. The surface area of Beaver Lake is about 27,900 acres and approximately 449 miles of shoreline are at the conservation pool level (1,120 feet above the North American Vertical Datum of 1988). Sedimentation in reservoirs can result in reduced water storage capacity and a reduction in usable aquatic habitat. Therefore, accurate and up-to-date estimates of reservoir water capacity are important for managing pool levels, power generation, recreation, and downstream aquatic habitat. Many of the lakes operated by the U.S. Army Corps of Engineers are periodically surveyed to monitor bathymetric changes that affect water capacity. In October 2018, the U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, completed one such survey of Beaver Lake using a multibeam echosounder. The echosounder data were combined with light detection and ranging (lidar) data to prepare a bathymetric map and a surface area and capacity table.
- 1 January 2016
- Published by US Geological Survey in Scientific Investigations Report
Estimation of peak discharge quantiles for selected annual exceedance probabilities in northeastern Illinois
First posted June 28, 2016 Revised November 28, 2017 Director, Illinois Water Science Center U.S. Geological Survey 405 North Goodwin Avenue Urbana, IL 61801 http://il.water.usgs.gov This report provides two sets of equations for estimating peak discharge quantiles at annual exceedance probabilities (AEPs) of 0.50, 0.20, 0.10, 0.04, 0.02, 0.01, 0.005, and 0.002 (recurrence intervals of 2, 5, 10, 25, 50, 100, 200, and 500 years, respectively) for watersheds in Illinois based on annual maximum peak discharge data from 117 watersheds in and near northeastern Illinois. One set of equations was developed through a temporal analysis with a two-step least squares-quantile regression technique that measures the average effect of changes in the urbanization of the watersheds used in the study. The resulting equations can be used to adjust rural peak discharge quantiles for the effect of urbanization, and in this study the equations also were used to adjust the annual maximum peak discharges from the study watersheds to 2010 urbanization conditions. The other set of equations was developed by a spatial analysis. This analysis used generalized least-squares regression to fit the peak discharge quantiles computed from the urbanization-adjusted annual maximum peak discharges from the study watersheds to drainage-basin characteristics. The peak discharge quantiles were computed by using the Expected Moments Algorithm following the removal of potentially influential low floods defined by a multiple Grubbs-Beck test. To improve the quantile estimates, regional skew coefficients were obtained from a newly developed regional skew model in which the skew increases with the urbanized land use fraction. The drainage-basin characteristics used as explanatory variables in the spatial analysis include drainage area, the fraction of developed land, the fraction of land with poorly drained soils or likely water, and the basin slope estimated as the ratio of the basin relief to basin perimeter. This report also provides the following: (1) examples to illustrate the use of the spatial and urbanization-adjustment equations for estimating peak discharge quantiles at ungaged sites and to improve flood-quantile estimates at and near a gaged site; (2) the urbanization-adjusted annual maximum peak discharges and peak discharge quantile estimates at streamgages from 181 watersheds including the 117 study watersheds and 64 additional watersheds in the study region that were originally considered for use in the study but later deemed to be redundant. The urbanization-adjustment equations, spatial regression equations, and peak discharge quantile estimates developed in this study will be made available in the web application StreamStats, which provides automated regression-equation solutions for user-selected stream locations. Figures and tables comparing the observed and urbanization-adjusted annual maximum peak discharge records by streamgage are provided at https://doi.org/10.3133/sir20165050 for download.
- 1 January 2016
- Published by US Geological Survey in Scientific Investigations Report
Estimation of peak discharge quantiles for selected annual exceedance probabilities in northeastern Illinois
First posted June 28, 2016 Revised November 28, 2017 Director, Illinois Water Science Center U.S. Geological Survey 405 North Goodwin Avenue Urbana, IL 61801 http://il.water.usgs.gov This report provides two sets of equations for estimating peak discharge quantiles at annual exceedance probabilities (AEPs) of 0.50, 0.20, 0.10, 0.04, 0.02, 0.01, 0.005, and 0.002 (recurrence intervals of 2, 5, 10, 25, 50, 100, 200, and 500 years, respectively) for watersheds in Illinois based on annual maximum peak discharge data from 117 watersheds in and near northeastern Illinois. One set of equations was developed through a temporal analysis with a two-step least squares-quantile regression technique that measures the average effect of changes in the urbanization of the watersheds used in the study. The resulting equations can be used to adjust rural peak discharge quantiles for the effect of urbanization, and in this study the equations also were used to adjust the annual maximum peak discharges from the study watersheds to 2010 urbanization conditions. The other set of equations was developed by a spatial analysis. This analysis used generalized least-squares regression to fit the peak discharge quantiles computed from the urbanization-adjusted annual maximum peak discharges from the study watersheds to drainage-basin characteristics. The peak discharge quantiles were computed by using the Expected Moments Algorithm following the removal of potentially influential low floods defined by a multiple Grubbs-Beck test. To improve the quantile estimates, regional skew coefficients were obtained from a newly developed regional skew model in which the skew increases with the urbanized land use fraction. The drainage-basin characteristics used as explanatory variables in the spatial analysis include drainage area, the fraction of developed land, the fraction of land with poorly drained soils or likely water, and the basin slope estimated as the ratio of the basin relief to basin perimeter. This report also provides the following: (1) examples to illustrate the use of the spatial and urbanization-adjustment equations for estimating peak discharge quantiles at ungaged sites and to improve flood-quantile estimates at and near a gaged site; (2) the urbanization-adjusted annual maximum peak discharges and peak discharge quantile estimates at streamgages from 181 watersheds including the 117 study watersheds and 64 additional watersheds in the study region that were originally considered for use in the study but later deemed to be redundant. The urbanization-adjustment equations, spatial regression equations, and peak discharge quantile estimates developed in this study will be made available in the web application StreamStats, which provides automated regression-equation solutions for user-selected stream locations. Figures and tables comparing the observed and urbanization-adjusted annual maximum peak discharge records by streamgage are provided at https://doi.org/10.3133/sir20165050 for download.
- 1 January 2015
- Published by US Geological Survey
Bathymetric survey of Lake Calumet, Cook County, Illinois
- 1 January 2015
- Published by US Geological Survey
Bathymetric survey of Lake Calumet, Cook County, Illinois
- Open Access
- 1 January 2014
- Published by US Geological Survey
Estimation of regional flow-duration curves for Indiana and Illinois
- 1 January 2014
- Published by US Geological Survey
Open AccessEstimation of regional flow-duration curves for Indiana and Illinois
- 1 January 2013
- Published by US Geological Survey
Flood-inundation maps for the DuPage River from Plainfield to Shorewood, Illinois, 2013
- 1 January 2013
- Published by US Geological Survey
Flood-inundation maps for the DuPage River from Plainfield to Shorewood, Illinois, 2013