Cristina Favieres
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Cristina Favieres has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- José Vergara
Public University of Navarre
28 shared publications - Vicente Madurga
Laboratorio de Magnetismo, Dpto. de Ciencias, Campus Arrosadía s/n, Universidad Pública de Navarra (UPNA) 5 , E-31006 Pamplona
16 shared publications V. Madurga
Laboratorio de Magnetismo, Departamento de Ciencias, Física, Universidad Pública de Navarra (UPNA), Campus de Arrosadía 1 , Pamplona, España
12 shared publicationsC. Aroca
Departamento de Física Aplicada, ETSI Telecomunicación, Universidad Politécnica de Madrid, E-28040 Madrid, Spain
6 shared publications- César Magén
Instituto de Nanociencia y Materiales de Aragón (INMA), CSIC-Universidad de Zaragoza, 50009 Zaragoza, Spain
4 shared publications - Manuel Ricardo Ibarra
Instituto de Nanociencia y Materiales de Aragón (INMA), CSIC-Universidad de Zaragoza, 50009 Zaragoza, Spain
4 shared publications
Latest Publications
- Open Access
- 17 March 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (11)
Quest for amorphous superconductors of Bi–Sb alloys by irradiation with swift heavy ions
Crystalline Bi100−xSbx alloys are known as the first discovered topological insulators, as well as for their promising thermoelectric properties, while their amorphous counterparts exhibit superconductivity (Tc > 6 K). However, their strong tendency to crystallize has hindered both the study and practical applications of amorphous Bi and Bi–Sb alloys. To explore the possibility of obtaining amorphous superconducting phases and enhancing thermoelectric properties, we investigated ion-beam irradiation as a method to induce amorphization in Bi100−xSbx alloys. We report irradiation experiments on pure Bi and Bi100−xSbx using bismuth and iodine ions (tens of MeV), generating an estimated vacancy damage of 40%–80%. Structural characterization and electrical resistivity measurements (2–300 K) revealed that, while amorphization and superconductivity were not achieved, melt-spun samples exhibited an order of magnitude higher conductivity than thermally evaporated ones. Moreover, ion-induced disorder further improved electrical conductivity, particularly in Bi90Sb10, highlighting its potential for thermoelectric applications.
- 17 March 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (11)
Open AccessQuest for amorphous superconductors of Bi–Sb alloys by irradiation with swift heavy ions
Crystalline Bi100−xSbx alloys are known as the first discovered topological insulators, as well as for their promising thermoelectric properties, while their amorphous counterparts exhibit superconductivity (Tc > 6 K). However, their strong tendency to crystallize has hindered both the study and practical applications of amorphous Bi and Bi–Sb alloys. To explore the possibility of obtaining amorphous superconducting phases and enhancing thermoelectric properties, we investigated ion-beam irradiation as a method to induce amorphization in Bi100−xSbx alloys. We report irradiation experiments on pure Bi and Bi100−xSbx using bismuth and iodine ions (tens of MeV), generating an estimated vacancy damage of 40%–80%. Structural characterization and electrical resistivity measurements (2–300 K) revealed that, while amorphization and superconductivity were not achieved, melt-spun samples exhibited an order of magnitude higher conductivity than thermally evaporated ones. Moreover, ion-induced disorder further improved electrical conductivity, particularly in Bi90Sb10, highlighting its potential for thermoelectric applications.
- Open Access
- 12 September 2024
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 610
Thermal hysteresis in the structural, magnetic and transport properties of hard magnetic MnBi films
- 12 September 2024
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 610
Open AccessThermal hysteresis in the structural, magnetic and transport properties of hard magnetic MnBi films
- Open Access
- 1 February 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (2)
Generation of highly anisotropic physical properties in ferromagnetic thin films controlled by their differently oriented nano-sheets
We fabricated ferromagnetic nano-crystalline thin films of Co, Fe, Co–Fe and Co-rich and Fe-rich, Co–MT and Fe–MT (MT = transition metal), constituted by nano-sheets with a controlled slant. Visualization of these nano-sheets by Scanning Tunneling Microscopy and High-Resolution Transmission Electron Microscopy (HRTEM) showed typically tilt angles ≈56° with respect to the substrate plane, and nano-sheets ≈3.0–4.0 nm thick, ≈30–100 nm wide, and ≈200–300 nm long, with an inter-sheet distance of ≈0.9–1.2 nm, depending on their constitutive elements. Induced by this nano-morphology, these films exhibited large uniaxial magnetic anisotropy in the plane, the easy direction of magnetization being parallel to the longitudinal direction of the nano-sheets. In the as-grown films, typical values of the anisotropy field were between Hk ≈ 48 and 110 kA/m depending on composition. The changes in the nano-morphology caused by thermal treatments, and hence in the anisotropic properties, were also visualized by HRTEM, including chemical analysis at the nano-scale. Some films retained their nano-sheet morphology and increased their anisotropies by up to three times after being heated to at least 500 °C: for example, the thermal treatments produced crystallization processes and the growth of CoV and CoFe magnetic phases, maintaining the nano-sheet morphology. In contrast, other annealed films, Co, Fe, CoZn, CoCu… lost their nano-sheet morphology and hence their anisotropies. This work opens a path of study for these new magnetically anisotropic materials, particularly with respect to the nano-morphological and structural changes related to the increase in magnetic anisotropy.
- 1 February 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (2)
Open AccessGeneration of highly anisotropic physical properties in ferromagnetic thin films controlled by their differently oriented nano-sheets
We fabricated ferromagnetic nano-crystalline thin films of Co, Fe, Co–Fe and Co-rich and Fe-rich, Co–MT and Fe–MT (MT = transition metal), constituted by nano-sheets with a controlled slant. Visualization of these nano-sheets by Scanning Tunneling Microscopy and High-Resolution Transmission Electron Microscopy (HRTEM) showed typically tilt angles ≈56° with respect to the substrate plane, and nano-sheets ≈3.0–4.0 nm thick, ≈30–100 nm wide, and ≈200–300 nm long, with an inter-sheet distance of ≈0.9–1.2 nm, depending on their constitutive elements. Induced by this nano-morphology, these films exhibited large uniaxial magnetic anisotropy in the plane, the easy direction of magnetization being parallel to the longitudinal direction of the nano-sheets. In the as-grown films, typical values of the anisotropy field were between Hk ≈ 48 and 110 kA/m depending on composition. The changes in the nano-morphology caused by thermal treatments, and hence in the anisotropic properties, were also visualized by HRTEM, including chemical analysis at the nano-scale. Some films retained their nano-sheet morphology and increased their anisotropies by up to three times after being heated to at least 500 °C: for example, the thermal treatments produced crystallization processes and the growth of CoV and CoFe magnetic phases, maintaining the nano-sheet morphology. In contrast, other annealed films, Co, Fe, CoZn, CoCu… lost their nano-sheet morphology and hence their anisotropies. This work opens a path of study for these new magnetically anisotropic materials, particularly with respect to the nano-morphological and structural changes related to the increase in magnetic anisotropy.
- Open Access
- 10 July 2023
- Published by MDPI AG in Magnetochemistry
- Vol. 9 (7) , 179
Special Issue: Soft and Hard Magnetic Materials: Latest Advances and Prospects
The Special Issue Soft and Hard Magnetic Materials: Latest Advances and Prospects aims to provide researchers with an overview of some aspects of the current research in magnetic materials from theoretical studies to their applications, including their fabrication and characterization
- 10 July 2023
- Published by MDPI AG in Magnetochemistry
- Vol. 9 (7) , 179
Open AccessSpecial Issue: Soft and Hard Magnetic Materials: Latest Advances and Prospects
The Special Issue Soft and Hard Magnetic Materials: Latest Advances and Prospects aims to provide researchers with an overview of some aspects of the current research in magnetic materials from theoretical studies to their applications, including their fabrication and characterization
- 22 March 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 133 (12) , 124301
High magnetic, transport, and optical uniaxial anisotropies generated by controlled directionally grown nano-sheets in Fe thin films
Fe films with thicknesses between 17 and 95 nm were grown with a nano-sheet morphology, which enabled their high uniaxial magnetic, transport, and optical in-plane anisotropies. The top edge of the nano-sheets was directly visualized as nano-string-like structures of approximately 12.5–14 nm width and 100–300 nm length. The hysteresis loops showed a clear easy direction of magnetization in the longitudinal direction of the nano-sheets, whereas the hard direction loops were anhysteretic, with no remanence and zero coercive field. The anisotropy field exhibited values between 70 and 111 kA/m depending on the thickness of the films, with the maximum value corresponding to a 34 nm thick sample. The resistance of the films was also found to be highly anisotropic. The ratio (R⊥–R||)/R|| was ≈86%, with R|| and R⊥ being the resistances in the parallel and perpendicular directions of the nano-sheets, respectively. Likewise, the reflectivity of the samples behaved anisotropically; the ratio (IReflmax–IReflmin)/IReflmax of the intensity of reflected light by the films reached up to 61% for 34 nm thick samples, achieving the maximum value, IReflmax, when the plane of the incident light coincided with the direction of the nano-sheets and the minimum, IReflmin, when this plane was perpendicular to the direction of the nano-sheets. The origin of these anisotropic behaviors was established. These anisotropic films with high magnetization and high uniaxial anisotropies at the nanoscale can be useful for microelectronics applications, for devices such as magnetic sensors and transducers, or for ultrahigh frequency inductors.
- 22 March 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 133 (12) , 124301
High magnetic, transport, and optical uniaxial anisotropies generated by controlled directionally grown nano-sheets in Fe thin films
Fe films with thicknesses between 17 and 95 nm were grown with a nano-sheet morphology, which enabled their high uniaxial magnetic, transport, and optical in-plane anisotropies. The top edge of the nano-sheets was directly visualized as nano-string-like structures of approximately 12.5–14 nm width and 100–300 nm length. The hysteresis loops showed a clear easy direction of magnetization in the longitudinal direction of the nano-sheets, whereas the hard direction loops were anhysteretic, with no remanence and zero coercive field. The anisotropy field exhibited values between 70 and 111 kA/m depending on the thickness of the films, with the maximum value corresponding to a 34 nm thick sample. The resistance of the films was also found to be highly anisotropic. The ratio (R⊥–R||)/R|| was ≈86%, with R|| and R⊥ being the resistances in the parallel and perpendicular directions of the nano-sheets, respectively. Likewise, the reflectivity of the samples behaved anisotropically; the ratio (IReflmax–IReflmin)/IReflmax of the intensity of reflected light by the films reached up to 61% for 34 nm thick samples, achieving the maximum value, IReflmax, when the plane of the incident light coincided with the direction of the nano-sheets and the minimum, IReflmin, when this plane was perpendicular to the direction of the nano-sheets. The origin of these anisotropic behaviors was established. These anisotropic films with high magnetization and high uniaxial anisotropies at the nanoscale can be useful for microelectronics applications, for devices such as magnetic sensors and transducers, or for ultrahigh frequency inductors.
- Open Access
- 29 July 2022
- Published by MDPI AG in Magnetochemistry
- Vol. 8 (8) , 82
Influence of Bi Content on the Temperature of the Formation of the Hard Magnetic MnBi Phase: Simultaneous Irreversible Drop of Resistance
Pulsed laser-deposited (PLD) MnBi films were fabricated by alternating deposition of Mn and Bi layers. In order to obtain the ferromagnetic MnBi phase, heat treatments were performed on the samples. Simultaneously, the resistance of the samples was monitored as a function of the temperature. Thus, on increasing the temperature, a steep decrease in the resistance of the films was observed, simultaneous to the onset of the formation of the MnBi phase. At room-temperature, these annealed samples showed a ferromagnetic behavior, as well as the presence of the characteristic LT-MnBi phase diffraction peaks in the X-ray diffraction patterns. The temperature of the generation of the MnBi phase depended on the relative concentration of Mn and Bi in the different samples: on increasing the Bi atomic concentration, the temperature of the generation of the MnBi phase decreased.
- 29 July 2022
- Published by MDPI AG in Magnetochemistry
- Vol. 8 (8) , 82
Open AccessInfluence of Bi Content on the Temperature of the Formation of the Hard Magnetic MnBi Phase: Simultaneous Irreversible Drop of Resistance
Pulsed laser-deposited (PLD) MnBi films were fabricated by alternating deposition of Mn and Bi layers. In order to obtain the ferromagnetic MnBi phase, heat treatments were performed on the samples. Simultaneously, the resistance of the samples was monitored as a function of the temperature. Thus, on increasing the temperature, a steep decrease in the resistance of the films was observed, simultaneous to the onset of the formation of the MnBi phase. At room-temperature, these annealed samples showed a ferromagnetic behavior, as well as the presence of the characteristic LT-MnBi phase diffraction peaks in the X-ray diffraction patterns. The temperature of the generation of the MnBi phase depended on the relative concentration of Mn and Bi in the different samples: on increasing the Bi atomic concentration, the temperature of the generation of the MnBi phase decreased.
- Open Access
- 12 April 2022
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 911
Vanadium trapped by oblique nano-sheets to preserve the anisotropy in Co–V thin films at high temperature
- 12 April 2022
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 911
Open AccessVanadium trapped by oblique nano-sheets to preserve the anisotropy in Co–V thin films at high temperature
- Open Access
- 28 December 2021
- Published by MDPI AG in Magnetochemistry
- Vol. 8 (1) , 4
Tailoring Magnetic and Transport Anisotropies in Co100−x–Cux Thin Films through Obliquely Grown Nano-Sheets
The magnetic and transport properties of pulsed laser-deposited Co100−x–Cux thin films were tailored through their nano-morphology and composition by controlling for the deposition geometry, namely normal or oblique deposition, and their Cu content. All films were composed of an amorphous Co matrix and a textured growth of Cu nanocrystals, whose presence and size d increased as x increased. For x = 50, all films were superparamagnetic, regardless of deposition geometry. The normally deposited films showed no in-plane magnetic anisotropy. On the contrary, controllable in-plane uniaxial magnetic anisotropy in both direction and magnitude was generated in the obliquely deposited films. The magnetic anisotropy field Hk remained constant for x = 0, 5 and 10, Hk ≈ 35 kAm−1, and decreased to 28 and 26 kAm−1 for x = 20 and 30, respectively. This anisotropy had a magnetostatic origin due to a tilted nano-sheet morphology. In the normally deposited films, the coercive field Hc increased when x increased, from 200 (x = 0) to 1100 Am−1 (x = 30). In contrast, in obliquely deposited films, Hc decreased from 1500 (x = 0) to 100 Am−1 (x = 30) as x increased. Activation energy spectra corresponding to structural relaxation phenomena in obliquely deposited films were obtained from transport property measurements. They revealed two peaks, which also depended on their nano-morphology and composition.
- 28 December 2021
- Published by MDPI AG in Magnetochemistry
- Vol. 8 (1) , 4
Open AccessTailoring Magnetic and Transport Anisotropies in Co100−x–Cux Thin Films through Obliquely Grown Nano-Sheets
The magnetic and transport properties of pulsed laser-deposited Co100−x–Cux thin films were tailored through their nano-morphology and composition by controlling for the deposition geometry, namely normal or oblique deposition, and their Cu content. All films were composed of an amorphous Co matrix and a textured growth of Cu nanocrystals, whose presence and size d increased as x increased. For x = 50, all films were superparamagnetic, regardless of deposition geometry. The normally deposited films showed no in-plane magnetic anisotropy. On the contrary, controllable in-plane uniaxial magnetic anisotropy in both direction and magnitude was generated in the obliquely deposited films. The magnetic anisotropy field Hk remained constant for x = 0, 5 and 10, Hk ≈ 35 kAm−1, and decreased to 28 and 26 kAm−1 for x = 20 and 30, respectively. This anisotropy had a magnetostatic origin due to a tilted nano-sheet morphology. In the normally deposited films, the coercive field Hc increased when x increased, from 200 (x = 0) to 1100 Am−1 (x = 30). In contrast, in obliquely deposited films, Hc decreased from 1500 (x = 0) to 100 Am−1 (x = 30) as x increased. Activation energy spectra corresponding to structural relaxation phenomena in obliquely deposited films were obtained from transport property measurements. They revealed two peaks, which also depended on their nano-morphology and composition.
- Open Access
Surface Roughness Influence on Néel-, Crosstie, and Bloch-Type Charged Zigzag Magnetic Domain Walls in Nanostructured Fe Films
Charged magnetic domain walls have been visualized in soft magnetic nanostructured Fe thin films under both static and dynamic conditions. A transition in the core of these zigzagged magnetic walls from Néel-type to Bloch-type through the formation of crosstie walls has been observed. This transition in charged zigzagged walls was not previously shown experimentally in Fe thin films. For film thicknesses t < 30 nm, Néel-type cores are present, while at t ≈ 33 nm, walls with crosstie cores are observed. At t > 60 nm, Bloch-type cores are observed. Along with the visualization of these critical parameters, the dependence on the film thickness of the characteristic angle and length of the segments of the zigzagged walls has been observed and analyzed. After measuring the bistable magneto-optical behavior, the values of the wall nucleation magnetic field and the surface roughness of the films, an energetic fit to these nucleation values is presented.
Open AccessSurface Roughness Influence on Néel-, Crosstie, and Bloch-Type Charged Zigzag Magnetic Domain Walls in Nanostructured Fe Films
Charged magnetic domain walls have been visualized in soft magnetic nanostructured Fe thin films under both static and dynamic conditions. A transition in the core of these zigzagged magnetic walls from Néel-type to Bloch-type through the formation of crosstie walls has been observed. This transition in charged zigzagged walls was not previously shown experimentally in Fe thin films. For film thicknesses t < 30 nm, Néel-type cores are present, while at t ≈ 33 nm, walls with crosstie cores are observed. At t > 60 nm, Bloch-type cores are observed. Along with the visualization of these critical parameters, the dependence on the film thickness of the characteristic angle and length of the segments of the zigzagged walls has been observed and analyzed. After measuring the bistable magneto-optical behavior, the values of the wall nucleation magnetic field and the surface roughness of the films, an energetic fit to these nucleation values is presented.