Brendan Scott
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Brendan Scott has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Mark B. Jaksa
School of Architecture and Civil Engineering, The University of Adelaide, Adelaide, Australia
6 shared publications - Akshay Kumar Agarwal
Adelaide Univ
3 shared publications Mark Jaksa
3 shared publications- Peter Mitchell
Technical Director – Geotechnical Engineering, Aurecon, Adelaide, Australia; Adjunct Professor, School of Civil, Environmental & Mining Engineering, The University of Adelaide, Adelaide, South Australia, Australia
3 shared publications Mark B. Jaksa
Adelaide Univ
2 shared publicationsYien Lik Kuo
Adelaide Univ
2 shared publications
Latest Publications
- 1 November 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 39 (6)
Comparison of Compaction Techniques on Lunar Highland Regolith Simulant
National Aeronautics and Space Administration (NASA) is preparing to deploy astronauts for detailed exploration of the lunar South Pole, an area primarily composed of lunar highlands regolith. A comprehensive understanding of the composition, properties, and behavior of this surface material is critical to the success of the mission, to advancing the field of lunar exploration research, and future endeavors on the Moon. This study showcases the findings from laboratory tests conducted using a scaled-down model of two types of compaction equipment: a vibrating smooth drum roller (VSDR) and a rolling dynamic compaction (RDC) 4-sided impact roller. The experiments were performed using 1:13 scale models and utilized lunar highland simulant as the test material. Surface settlements, earth pressure cells, and densities were measured to quantify the extent of improvement for these two different compaction techniques. The results indicate that the vibrating smooth drum roller technique outperforms the impact roller in surface settlement, density, earth pressure and acceleration, demonstrating superior performance in compacting lunar highland regolith simulant.
- 1 November 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 39 (6)
Comparison of Compaction Techniques on Lunar Highland Regolith Simulant
National Aeronautics and Space Administration (NASA) is preparing to deploy astronauts for detailed exploration of the lunar South Pole, an area primarily composed of lunar highlands regolith. A comprehensive understanding of the composition, properties, and behavior of this surface material is critical to the success of the mission, to advancing the field of lunar exploration research, and future endeavors on the Moon. This study showcases the findings from laboratory tests conducted using a scaled-down model of two types of compaction equipment: a vibrating smooth drum roller (VSDR) and a rolling dynamic compaction (RDC) 4-sided impact roller. The experiments were performed using 1:13 scale models and utilized lunar highland simulant as the test material. Surface settlements, earth pressure cells, and densities were measured to quantify the extent of improvement for these two different compaction techniques. The results indicate that the vibrating smooth drum roller technique outperforms the impact roller in surface settlement, density, earth pressure and acceleration, demonstrating superior performance in compacting lunar highland regolith simulant.
- Open Access
- 10 August 2026
- Published by Open Engineering Inc in engrXiv
Experimental investigation of compaction behaviour of lunar highlands regolith simulant using a second-generation lunar vibratory drum roller
The construction of future lunar infrastructure will require efficient ground improvement techniques capable of increasing the density and load-bearing capacity of lunar regolith to support foundations, landing pads, mobility corridors, and in situ resource utilisation (ISRU) facilities. This study presents the development and experimental evaluation of a second-generation lunar vibrating drum roller (LVDR-2) scale model, incorporating an internally mounted eccentric mass to more closely replicate the operating principle of full-scale vibratory compaction equipment. Laboratory experiments were conducted using engineering-grade lunar highlands regolith simulant (LHS-1E) to investigate the coupled influence of translational speed, vibration frequency, and eccentric mass on compaction performance. Surface settlement and vertical pressures were initially measured to identify the optimum operating combination. The highest peak pressure was recorded at a translational speed of 4 km/h, a vibration frequency of 40 Hz, and an eccentric mass of 75.8 g. This combination was subsequently adopted for detailed geotechnical investigations involving surface settlement, vertical pressure, cone penetration resistance, bulk density, and vane shear strength measurements. The optimised LVDR-2 model demonstrated enhanced compaction performance, characterised by greater surface settlement, higher cone penetration resistance, increased bulk density, and deeper stress transmission within the simulant compared with the earlier LVDR-1 model. These findings provide important design guidance for the development of mechanised lunar ground improvement systems supporting future lunar infrastructure construction.
- 10 August 2026
- Published by Open Engineering Inc in engrXiv
Open AccessExperimental investigation of compaction behaviour of lunar highlands regolith simulant using a second-generation lunar vibratory drum roller
The construction of future lunar infrastructure will require efficient ground improvement techniques capable of increasing the density and load-bearing capacity of lunar regolith to support foundations, landing pads, mobility corridors, and in situ resource utilisation (ISRU) facilities. This study presents the development and experimental evaluation of a second-generation lunar vibrating drum roller (LVDR-2) scale model, incorporating an internally mounted eccentric mass to more closely replicate the operating principle of full-scale vibratory compaction equipment. Laboratory experiments were conducted using engineering-grade lunar highlands regolith simulant (LHS-1E) to investigate the coupled influence of translational speed, vibration frequency, and eccentric mass on compaction performance. Surface settlement and vertical pressures were initially measured to identify the optimum operating combination. The highest peak pressure was recorded at a translational speed of 4 km/h, a vibration frequency of 40 Hz, and an eccentric mass of 75.8 g. This combination was subsequently adopted for detailed geotechnical investigations involving surface settlement, vertical pressure, cone penetration resistance, bulk density, and vane shear strength measurements. The optimised LVDR-2 model demonstrated enhanced compaction performance, characterised by greater surface settlement, higher cone penetration resistance, increased bulk density, and deeper stress transmission within the simulant compared with the earlier LVDR-1 model. These findings provide important design guidance for the development of mechanised lunar ground improvement systems supporting future lunar infrastructure construction.
- Open Access
- 4 May 2026
- Published by Open Engineering Inc in engrXiv
Compaction performance of a scale model vibrating drum roller on lunar highlands regolith simulant
As NASA is progressing towards crewed long-term missions to the lunar South Pole, a detailed understanding of the geotechnical behaviour of lunar highlands regolith will be essential for the design of foundations, mobility systems, and in situ construction processes. This study investigates the compaction behaviour of a lunar highlands regolith simulant using a scale model lunar vibrating drum roller (LVDR-1). Two drum roller masses—2.92 kg and 4.45 kg—were examined under controlled vibration frequencies and translational scale speeds. For the 2.92 kg mass, scale speeds of 2 km/h and 4 km/h were tested at 40 Hz and 30 Hz, respectively, whilst for the 4.45 kg mass, scale speeds of 2 km/h and 6 km/h were tested at 40 Hz to evaluate their influence on compaction performance. Key parameters, including surface settlement, vertical pressure, penetration resistance, and bulk density, were recorded to assess the effectiveness of each roller configuration. The results show that the heavier roller mass consistently provides superior compaction performance, achieving greater surface deformation, higher penetration resistance, increased bulk density, and deeper stress transmission within the simulant bed.
- 4 May 2026
- Published by Open Engineering Inc in engrXiv
Open AccessCompaction performance of a scale model vibrating drum roller on lunar highlands regolith simulant
As NASA is progressing towards crewed long-term missions to the lunar South Pole, a detailed understanding of the geotechnical behaviour of lunar highlands regolith will be essential for the design of foundations, mobility systems, and in situ construction processes. This study investigates the compaction behaviour of a lunar highlands regolith simulant using a scale model lunar vibrating drum roller (LVDR-1). Two drum roller masses—2.92 kg and 4.45 kg—were examined under controlled vibration frequencies and translational scale speeds. For the 2.92 kg mass, scale speeds of 2 km/h and 4 km/h were tested at 40 Hz and 30 Hz, respectively, whilst for the 4.45 kg mass, scale speeds of 2 km/h and 6 km/h were tested at 40 Hz to evaluate their influence on compaction performance. Key parameters, including surface settlement, vertical pressure, penetration resistance, and bulk density, were recorded to assess the effectiveness of each roller configuration. The results show that the heavier roller mass consistently provides superior compaction performance, achieving greater surface deformation, higher penetration resistance, increased bulk density, and deeper stress transmission within the simulant bed.
- Open Access
- 2 February 2026
- Published by Open Engineering Inc in engrXiv
Density, strength and compressibility characteristics of lunar regolith simulant
Humankind will soon be returning to the Moon, as part of NASA’s Artemis program, where the objective is long-term habitation to facilitate extra-terrestrial exploration and in situ resource utilisation. The Artemis program is focused on inhabiting the Moon’s South pole, which consists of lunar highlands regolith. The Lunar Construction Group, which is part of the University of Adelaide’s Andy Thomas Centre for Space Resources (ATCSR), is actively undertaking research to design and construct infrastructure on the Moon. Due to the lack of availability of lunar regolith samples, lunar simulants have been developed which are intended to provide authentic surrogates of lunar regolith. It is essential, for the development of sustainable and resilient lunar infrastructure, that the geotechnical characteristics of the regolith are quantified and understood. This paper begins by first summarising the known ground conditions on the Moon and then presents the results of laboratory testing on three lunar simulants LHS-1 (lunar highland simulant), MAB-1 (a modified lunar highland simulant, which is a mixture of anorthosite and basalt), and LMS-1 (lunar mare simulant), in order to quantify their strength and compressibility characteristics.
- 2 February 2026
- Published by Open Engineering Inc in engrXiv
Open AccessDensity, strength and compressibility characteristics of lunar regolith simulant
Humankind will soon be returning to the Moon, as part of NASA’s Artemis program, where the objective is long-term habitation to facilitate extra-terrestrial exploration and in situ resource utilisation. The Artemis program is focused on inhabiting the Moon’s South pole, which consists of lunar highlands regolith. The Lunar Construction Group, which is part of the University of Adelaide’s Andy Thomas Centre for Space Resources (ATCSR), is actively undertaking research to design and construct infrastructure on the Moon. Due to the lack of availability of lunar regolith samples, lunar simulants have been developed which are intended to provide authentic surrogates of lunar regolith. It is essential, for the development of sustainable and resilient lunar infrastructure, that the geotechnical characteristics of the regolith are quantified and understood. This paper begins by first summarising the known ground conditions on the Moon and then presents the results of laboratory testing on three lunar simulants LHS-1 (lunar highland simulant), MAB-1 (a modified lunar highland simulant, which is a mixture of anorthosite and basalt), and LMS-1 (lunar mare simulant), in order to quantify their strength and compressibility characteristics.
- 22 October 2024
- Published by Springer Nature
- p. 81-89
The Carbon Footprint of Vibratory and Impact Rolling: A Sustainable Option for Bulk Earthworks on Infrastructure Projects
- 22 October 2024
- Published by Springer Nature
- p. 81-89
The Carbon Footprint of Vibratory and Impact Rolling: A Sustainable Option for Bulk Earthworks on Infrastructure Projects
- Open Access
- 1 May 2021
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Ground Improvement
- Vol. 174 (2) , 85-94
Depth of influence of rolling dynamic compaction
The depth of influence of rolling dynamic compaction (RDC) was investigated in a field trial using a four-sided impact roller. Earth pressure cells (EPCs) were placed at varying depths at a site consisting of homogeneous soil conditions. EPCs measured pressures imparted by RDC at 3·85 m depth; however, the largest magnitudes of pressure were confined to the top 2 m beneath the ground surface. These results were complemented by field density data, penetrometer and geophysical testing. A number of published case studies using the 8 t four-sided impact roller, for either improving ground in situ or compacting soil in thick layers, are summarised in this paper. Finally, equations are presented that predict first, the effective depth of improvement, appropriate for determining the depth to which the ground can be significantly improved in situ, and, second, the depth of major improvement for RDC, appropriate for thick-layer compaction.
- 1 May 2021
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Ground Improvement
- Vol. 174 (2) , 85-94
Open AccessDepth of influence of rolling dynamic compaction
The depth of influence of rolling dynamic compaction (RDC) was investigated in a field trial using a four-sided impact roller. Earth pressure cells (EPCs) were placed at varying depths at a site consisting of homogeneous soil conditions. EPCs measured pressures imparted by RDC at 3·85 m depth; however, the largest magnitudes of pressure were confined to the top 2 m beneath the ground surface. These results were complemented by field density data, penetrometer and geophysical testing. A number of published case studies using the 8 t four-sided impact roller, for either improving ground in situ or compacting soil in thick layers, are summarised in this paper. Finally, equations are presented that predict first, the effective depth of improvement, appropriate for determining the depth to which the ground can be significantly improved in situ, and, second, the depth of major improvement for RDC, appropriate for thick-layer compaction.
- Open Access
- 1 February 2020
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
- Vol. 12 (1) , 126-134
Influence of towing speed on effectiveness of rolling dynamic compaction
- 1 February 2020
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
- Vol. 12 (1) , 126-134
Open AccessInfluence of towing speed on effectiveness of rolling dynamic compaction
- Open Access
- 1 June 2019
- Published by Emerald Publishing in Géotechnique Letters
- Vol. 9 (2) , 99-105
Ground response to rolling dynamic compaction
Rolling dynamic compaction (RDC) is typically used for improving ground in situ or compacting fill in thick lifts. In many project applications, the effects of RDC are verified by way of testing that is undertaken pre- and/or post-compaction. This study presents results from a full-scale field trial that involved placing an earth pressure cell (EPC) and accelerometers at a depth of 0·7 m within a 1·5 m thick layer of homogeneous sandy gravel to measure the response to RDC in real-time. Double integration of acceleration–time data enabled settlement to be inferred, while the EPC measured the change in stress due to impact. The maximum change in vertical stress recorded over the 80 passes undertaken was approximately 1100 kPa. During a typical module impact, the loading and unloading response occurred over a duration of approximately 0·05 s. The acceleration response of RDC was measured in three orthogonal directions, with the vertical accelerations dominant.
- 1 June 2019
- Published by Emerald Publishing in Géotechnique Letters
- Vol. 9 (2) , 99-105
Open AccessGround response to rolling dynamic compaction
Rolling dynamic compaction (RDC) is typically used for improving ground in situ or compacting fill in thick lifts. In many project applications, the effects of RDC are verified by way of testing that is undertaken pre- and/or post-compaction. This study presents results from a full-scale field trial that involved placing an earth pressure cell (EPC) and accelerometers at a depth of 0·7 m within a 1·5 m thick layer of homogeneous sandy gravel to measure the response to RDC in real-time. Double integration of acceleration–time data enabled settlement to be inferred, while the EPC measured the change in stress due to impact. The maximum change in vertical stress recorded over the 80 passes undertaken was approximately 1100 kPa. During a typical module impact, the loading and unloading response occurred over a duration of approximately 0·05 s. The acceleration response of RDC was measured in three orthogonal directions, with the vertical accelerations dominant.
- 1 January 2015
- Published by Elsevier
- p. 429-452
A Field-Based Study of the Effectiveness of Rolling Dynamic Compaction
- 1 January 2015
- Published by Elsevier
- p. 429-452
A Field-Based Study of the Effectiveness of Rolling Dynamic Compaction