Anton Kepic
Research Subjects
Research Interests
Anton Kepic has a total of 147 co-authors. Here are the top co-authors by number of shared publications:
M. Urosevic
13 shared publications- Roman Pevzner
Centre for Exploration Geophysics, Curtin University, GPO Box U1987, Perth, WA 6845, Australia
13 shared publications Milovan Urosevic
10 shared publicationsB. D. Harris
Department of Exploration Geophysics Curtin University Perth Western Australia Australia
6 shared publicationsK. E. Butler
Department of Geology University of New Brunswick Fredericton, New Brunswick Canada
6 shared publications- Konstantin Tertyshnikov
Centre for Exploration Geophysics, Curtin University, GPO Box U1987, Perth, WA 6845, Australia
6 shared publications
Latest Publications
- 12 August 2026
- Published by Macedonian Association for Geotechnics
- p. 485-490
Combined geophysical techniques to predict and map rock mechanics parameters
Rock strength and hardness is often interpolated from relatively sparse data spanning tens to hundreds of metres away from diamond-core drilling or interpolated by hand logging and interpretation of rock-core. Geophysical methods should be the natural supporting data for inferring and interpolating information around and between boreholes. Fundamental shared relationships between geophysics measurements and mechanical properties of rock have been noted, tested and studied. However, a well-structured, statistically testable, and economically viable approach of melding geophysical measurement and rock engineering properties does not seem to be regular practice in the mining, or in many civil engineering projects. Cross-borehole seismic tomography while drilling with instrumented/logged holes gathering data appears to be most ready to meet the current and future digital mine-civil engineering needs for useful high resolution, volumetric information. By imaging subsurface rock properties through the analysis of seismic wave propagation, tomography provides valuable insight into the structural, mechanical, and dynamic behaviour of rock masses. Providing 3D maps of P- and S-wave velocity in a block model offers vast potential in decision making by allowing informed plans instead of reactive measures or allowing dilution or waste. At the former Brukunga pyrite-sulphur mine site (in South Australia) we have been investigating the possibility of using cross-borehole seismic travel time tomography with enhanced analysis of borehole wireline data to predict fracture intensity (such as RQD) and rock strength (UCS) as a case history test whether we can predict rock mechanical information and extrapolate to a rock volume. Our proposed methodology provides quantitative and repeatable measurements suitable for physical modelling and offers the opportunity to populate rock block models with engineering data in engineering units.
- 12 August 2026
- Published by Macedonian Association for Geotechnics
- p. 485-490
Combined geophysical techniques to predict and map rock mechanics parameters
Rock strength and hardness is often interpolated from relatively sparse data spanning tens to hundreds of metres away from diamond-core drilling or interpolated by hand logging and interpretation of rock-core. Geophysical methods should be the natural supporting data for inferring and interpolating information around and between boreholes. Fundamental shared relationships between geophysics measurements and mechanical properties of rock have been noted, tested and studied. However, a well-structured, statistically testable, and economically viable approach of melding geophysical measurement and rock engineering properties does not seem to be regular practice in the mining, or in many civil engineering projects. Cross-borehole seismic tomography while drilling with instrumented/logged holes gathering data appears to be most ready to meet the current and future digital mine-civil engineering needs for useful high resolution, volumetric information. By imaging subsurface rock properties through the analysis of seismic wave propagation, tomography provides valuable insight into the structural, mechanical, and dynamic behaviour of rock masses. Providing 3D maps of P- and S-wave velocity in a block model offers vast potential in decision making by allowing informed plans instead of reactive measures or allowing dilution or waste. At the former Brukunga pyrite-sulphur mine site (in South Australia) we have been investigating the possibility of using cross-borehole seismic travel time tomography with enhanced analysis of borehole wireline data to predict fracture intensity (such as RQD) and rock strength (UCS) as a case history test whether we can predict rock mechanical information and extrapolate to a rock volume. Our proposed methodology provides quantitative and repeatable measurements suitable for physical modelling and offers the opportunity to populate rock block models with engineering data in engineering units.
- 12 August 2026
- Published by Macedonian Association for Geotechnics
- p. 479-484
A robust sampling strategy for UCS using wireline geophysics
Determining where to sample a diamond drillcore and estimating how many Unconfined Compression Test (UCS) samples would be needed to obtain accurate data are tasks largely based on qualitative knowledge. ISRM suggests taking a minimum of five samples per domain. Prior research has shown that due to the natural heterogeneity in rock better insights with statistically based estimations are usually needed. This hypothesis was confirmed in a recent study at the former Brukunga Mine site, South Australia. Our study in a hard/crystalline rock geology revealed a wider variation than initially anticipated. The UCS results from 162 samples showed a minimum value of 22.9 MPa, a maximum value of 320.2 MPa, and a CoV of 59%. Continuous full wave sonic (FWS), and density logs were extracted to calculate dynamic elastic modulus (Ed) along the length of a single borehole. Robust statistical methods were used to create a measure of variation of rock elastic modulus. This measure is called Relative Median of Absolute Deviation (RMAD) over a 5 m-long moving window. Gaussian Mixture Modelling identified a threshold of 3% RMAD that separates the geological record exposed in the borehole into mechanically homogeneous and anomalous zones. A sampling strategy was developed by combination of fuzzy c-means clustering domaining on continuous X-ray fluorescence geochemistry data as well as RMAD zones. The outcome of the study is a sampling strategy guided with RMAD that provides a measurable and quantitative means to take samples, based on the mechanical and geological conditions of the sampled medium.
- 12 August 2026
- Published by Macedonian Association for Geotechnics
- p. 479-484
A robust sampling strategy for UCS using wireline geophysics
Determining where to sample a diamond drillcore and estimating how many Unconfined Compression Test (UCS) samples would be needed to obtain accurate data are tasks largely based on qualitative knowledge. ISRM suggests taking a minimum of five samples per domain. Prior research has shown that due to the natural heterogeneity in rock better insights with statistically based estimations are usually needed. This hypothesis was confirmed in a recent study at the former Brukunga Mine site, South Australia. Our study in a hard/crystalline rock geology revealed a wider variation than initially anticipated. The UCS results from 162 samples showed a minimum value of 22.9 MPa, a maximum value of 320.2 MPa, and a CoV of 59%. Continuous full wave sonic (FWS), and density logs were extracted to calculate dynamic elastic modulus (Ed) along the length of a single borehole. Robust statistical methods were used to create a measure of variation of rock elastic modulus. This measure is called Relative Median of Absolute Deviation (RMAD) over a 5 m-long moving window. Gaussian Mixture Modelling identified a threshold of 3% RMAD that separates the geological record exposed in the borehole into mechanically homogeneous and anomalous zones. A sampling strategy was developed by combination of fuzzy c-means clustering domaining on continuous X-ray fluorescence geochemistry data as well as RMAD zones. The outcome of the study is a sampling strategy guided with RMAD that provides a measurable and quantitative means to take samples, based on the mechanical and geological conditions of the sampled medium.
- 14 July 2022
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 87 (6) , D189-D199
A method to indicate heavy minerals in logging-while-drilling
The low-energy region of the gamma ray spectrum, less than 200 keV, often is either discarded or not analyzed in borehole logging or airborne radiometric surveys. There is much useful information about earth properties to be extracted from the low-energy region because it is sensitive to photoelectric absorption within the rock, a process that is highly sensitive to the atomic number of the elements within the rock. In addition, the rate of photoelectric absorption is proportional to the density of the rock. At higher energies, the spectrum is primarily sensitive to density variations only. The ratio of counts in the two energy regions may be used as a heavy mineral indicator (HMI). This ratio normalizes density effects and is primarily sensitive to variations in the average (or effective) atomic number (Zeff) of the rock. Previous work by other authors has focused on the application of this idea for wireline logging with an isotopic source and multiple scattering of copious primary gamma rays, which allows for good counting statistics in the recorded spectrum. Recent advances in gamma ray detectors and logging-while-drilling (LWD) techniques open the possibility of applying the HMI measurement to the natural gamma ray LWD logs. Drilling speeds are much slower than the running speeds of wireline tools, resulting in improved counting statistics. Using computer simulations, laboratory experiments, and field measurements, we find that the natural gamma ray spectrum, recorded while (diamond) drilling, provides sufficient counting statistics to be used for robustly calculating HMI. As iron is the most abundant and influential element in photoelectric gamma ray scattering processes in rock fabrics, we postulate that we can, in most cases, use HMI to indicate the iron content of the rocks. The HMI calculated under these conditions provides a good measure of changes in Zeff of rocks and correlates well with iron-rich sections. Our field and laboratory tests demonstrate that the HMI measures can be used as a proxy to separate many metalliferous ores from waste based on the differences in Zeff.
- 14 July 2022
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 87 (6) , D189-D199
A method to indicate heavy minerals in logging-while-drilling
The low-energy region of the gamma ray spectrum, less than 200 keV, often is either discarded or not analyzed in borehole logging or airborne radiometric surveys. There is much useful information about earth properties to be extracted from the low-energy region because it is sensitive to photoelectric absorption within the rock, a process that is highly sensitive to the atomic number of the elements within the rock. In addition, the rate of photoelectric absorption is proportional to the density of the rock. At higher energies, the spectrum is primarily sensitive to density variations only. The ratio of counts in the two energy regions may be used as a heavy mineral indicator (HMI). This ratio normalizes density effects and is primarily sensitive to variations in the average (or effective) atomic number (Zeff) of the rock. Previous work by other authors has focused on the application of this idea for wireline logging with an isotopic source and multiple scattering of copious primary gamma rays, which allows for good counting statistics in the recorded spectrum. Recent advances in gamma ray detectors and logging-while-drilling (LWD) techniques open the possibility of applying the HMI measurement to the natural gamma ray LWD logs. Drilling speeds are much slower than the running speeds of wireline tools, resulting in improved counting statistics. Using computer simulations, laboratory experiments, and field measurements, we find that the natural gamma ray spectrum, recorded while (diamond) drilling, provides sufficient counting statistics to be used for robustly calculating HMI. As iron is the most abundant and influential element in photoelectric gamma ray scattering processes in rock fabrics, we postulate that we can, in most cases, use HMI to indicate the iron content of the rocks. The HMI calculated under these conditions provides a good measure of changes in Zeff of rocks and correlates well with iron-rich sections. Our field and laboratory tests demonstrate that the HMI measures can be used as a proxy to separate many metalliferous ores from waste based on the differences in Zeff.
- Open Access
- 1 May 2019
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 84 (3) , D131-D149
Experimental testing of semirigid corrugated baffles for the suppression of tube waves in vertical seismic profile data
Multichannel borehole hydrophone strings are a low-cost, low-risk, alternative to borehole clamping geophones. Vertical seismic profile (VSP) data collected with hydrophones, however, suffer from high-amplitude coherent tube-wave noise. This reduces the usable data to the first arrivals and traveltimes for check-shot surveys. To significantly reduce tube-wave noise from VSP data acquired with hydrophones, we have designed and tested a novel tube-wave attenuation baffle. The effectiveness of the baffle was first verified in a laboratory-scale experiment and then in a borehole drilled into a hardrock environment. The laboratory experiments tested the performance of four different baffle topologies, whereby the best performing topology was the semirigid corrugated pipe baffle. This design reduced the amplitude of the tube wave with more than 40 dB and was logistically easy to deploy. The field experiment investigated the effectiveness of three different semirigid corrugated pipe baffle topologies in a PQ (123 mm) diamond drillhole in Western Australia. Here, we found that the semirigid corrugated pipe baffle was effective in disrupting tube-wave propagation. The 100 mm diameter baffle achieved an impressive 60 dB of tube-wave attenuation, whereas the 50 mm baffle had a modest attenuation of 10–15 dB. This suggests that the performance of this new type of baffle is best when the diameter of the baffle is closely matched to the diameter of the borehole. The results of these experiments have significant implications because hydrophone arrays with a large number of receivers are comparatively inexpensive and simpler to deploy than borehole geophone counterparts. The development of hydrophone arrays that are free of interfering borehole modes could allow VSPs to be acquired in situations in which seismic-polarity information is not required and could help VSP gain traction in cases in which the cost of acquisition has precluded its use until now.
- 1 May 2019
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 84 (3) , D131-D149
Open AccessExperimental testing of semirigid corrugated baffles for the suppression of tube waves in vertical seismic profile data
Multichannel borehole hydrophone strings are a low-cost, low-risk, alternative to borehole clamping geophones. Vertical seismic profile (VSP) data collected with hydrophones, however, suffer from high-amplitude coherent tube-wave noise. This reduces the usable data to the first arrivals and traveltimes for check-shot surveys. To significantly reduce tube-wave noise from VSP data acquired with hydrophones, we have designed and tested a novel tube-wave attenuation baffle. The effectiveness of the baffle was first verified in a laboratory-scale experiment and then in a borehole drilled into a hardrock environment. The laboratory experiments tested the performance of four different baffle topologies, whereby the best performing topology was the semirigid corrugated pipe baffle. This design reduced the amplitude of the tube wave with more than 40 dB and was logistically easy to deploy. The field experiment investigated the effectiveness of three different semirigid corrugated pipe baffle topologies in a PQ (123 mm) diamond drillhole in Western Australia. Here, we found that the semirigid corrugated pipe baffle was effective in disrupting tube-wave propagation. The 100 mm diameter baffle achieved an impressive 60 dB of tube-wave attenuation, whereas the 50 mm baffle had a modest attenuation of 10–15 dB. This suggests that the performance of this new type of baffle is best when the diameter of the baffle is closely matched to the diameter of the borehole. The results of these experiments have significant implications because hydrophone arrays with a large number of receivers are comparatively inexpensive and simpler to deploy than borehole geophone counterparts. The development of hydrophone arrays that are free of interfering borehole modes could allow VSPs to be acquired in situations in which seismic-polarity information is not required and could help VSP gain traction in cases in which the cost of acquisition has precluded its use until now.
- Open Access
- 1 December 2018
- Published by Australian Society of Exploration Geophysicists in ASEG Extended Abstracts
- Vol. 2018 (1) , 1-8
How to build your own simple, low-cost, seismic system
Acquiring seismic data has typically been an expensive pursuit due to the high price of the acquisition systems. Such systems are also typically not easily adaptable to suit different acquisition scenarios. In this paper we detail how you can build your own simple, low-cost (~$60/channel), seismic acquisition system. Data recorded using such systems is comparable to that obtained using a far more expensive commercial seismograph. Seismic sources are similarly expensive with the only low-cost option being a sledgehammer. In this paper we also describe how to manufacture a small vibroseis unit from easily available components at a cost of less than $3,000. This unit has a wider, more controllable, bandwidth than an impact source and can be easily adapted to create a shear wave source for MASW surveys.
- 1 December 2018
- Published by Australian Society of Exploration Geophysicists in ASEG Extended Abstracts
- Vol. 2018 (1) , 1-8
Open AccessHow to build your own simple, low-cost, seismic system
Acquiring seismic data has typically been an expensive pursuit due to the high price of the acquisition systems. Such systems are also typically not easily adaptable to suit different acquisition scenarios. In this paper we detail how you can build your own simple, low-cost (~$60/channel), seismic acquisition system. Data recorded using such systems is comparable to that obtained using a far more expensive commercial seismograph. Seismic sources are similarly expensive with the only low-cost option being a sledgehammer. In this paper we also describe how to manufacture a small vibroseis unit from easily available components at a cost of less than $3,000. This unit has a wider, more controllable, bandwidth than an impact source and can be easily adapted to create a shear wave source for MASW surveys.
- Open Access
- 1 December 2018
- Published by Australian Society of Exploration Geophysicists in ASEG Extended Abstracts
- Vol. 2018 (1) , 1-6
Scintillators for PGNAA in Mineral Exploration
Current gamma-ray detectors, based upon scintillation, are not likely to perform well in narrow diameter logging-while-drilling (LWD), such as NQ diamond drilling. The normally used halide scintillators of NaI, CsI are considered to not have sufficient resolution to compensate for a lack of stopping power in PGNAA applications. Whereas, BGO, a robust oxide scintillator performs so poorly with respect to resolution, light output, and temperature sensitivity that the higher density and stopping power does not compensate fully for its limitations. We have evaluated several novel halide and oxide scintillators that might improve the viability PGNAA in small diameter LWD application. Specifically, we have looked at CsI, SrI, BGO, CWO, CeBr, GAGG, LaBr, YAP scintillators, and find that CeBr and CWO may be a useful alternative to LaBr in PGNAA applications. Our modelling and analysis indicates that very dense scintillators such as CWO, with moderate resolution capability, or moderate density with high resolution, such as CeBr and LaBr, are the best candidates for measuring line spectra from PGNAA with small, less than 50 mm diameter, detectors. However, none of the newer scintillators are a panacea as the penetrative nature of the PGNAA process means that a high background of scattered gamma rays will obscure many weak elemental peaks even with a “perfect” detector.
- 1 December 2018
- Published by Australian Society of Exploration Geophysicists in ASEG Extended Abstracts
- Vol. 2018 (1) , 1-6
Open AccessScintillators for PGNAA in Mineral Exploration
Current gamma-ray detectors, based upon scintillation, are not likely to perform well in narrow diameter logging-while-drilling (LWD), such as NQ diamond drilling. The normally used halide scintillators of NaI, CsI are considered to not have sufficient resolution to compensate for a lack of stopping power in PGNAA applications. Whereas, BGO, a robust oxide scintillator performs so poorly with respect to resolution, light output, and temperature sensitivity that the higher density and stopping power does not compensate fully for its limitations. We have evaluated several novel halide and oxide scintillators that might improve the viability PGNAA in small diameter LWD application. Specifically, we have looked at CsI, SrI, BGO, CWO, CeBr, GAGG, LaBr, YAP scintillators, and find that CeBr and CWO may be a useful alternative to LaBr in PGNAA applications. Our modelling and analysis indicates that very dense scintillators such as CWO, with moderate resolution capability, or moderate density with high resolution, such as CeBr and LaBr, are the best candidates for measuring line spectra from PGNAA with small, less than 50 mm diameter, detectors. However, none of the newer scintillators are a panacea as the penetrative nature of the PGNAA process means that a high background of scattered gamma rays will obscure many weak elemental peaks even with a “perfect” detector.
- 4 July 2018
- Published by Wiley in Geophysical Prospecting
- Vol. 67 (6) , 1686-1697
The construction of a simple portable electromagnetic vibrator from commercially available components
- 4 July 2018
- Published by Wiley in Geophysical Prospecting
- Vol. 67 (6) , 1686-1697
The construction of a simple portable electromagnetic vibrator from commercially available components
- Open Access
Near Real-Time Classification of Iron Ore Lithology by Applying Fuzzy Inference Systems to Petrophysical Downhole Data
Fluctuating commodity prices have repeatedly put the mining industry under pressure to increase productiveness and efficiency of their operations. Current procedures often rely heavily on manual analysis and interpretation although new technologies and analytical procedures are available to automate workflows. Grade control is one such issue where the laboratory assay turn-around times cannot beat the shovel. We propose that for iron ore deposits in the Pilbara geophysical downhole logging may provide the necessary and sufficient information about rock formation properties, circumventing any need for real-time elemental analysis entirely. This study provides an example where petrophysical downhole data is automatically classified using a neuro-adaptive learning algorithm to differentiate between different rock types of iron ore deposits and for grade estimation. We exploit a rarely used ability in a spectral gamma-gamma density tool to gather both density and iron content with a single geophysical measurement. This inaccurate data is then put into a neural fuzzy inference system to classify the rock into different grades and waste lithologies, with success rates nearly equal to those from laboratory geochemistry. The steps outlined in this study may be used to produce a workflow for current logging tools and future logging-while-drilling technologies for real-time iron ore grade estimation and lithological classification.
Open AccessNear Real-Time Classification of Iron Ore Lithology by Applying Fuzzy Inference Systems to Petrophysical Downhole Data
Fluctuating commodity prices have repeatedly put the mining industry under pressure to increase productiveness and efficiency of their operations. Current procedures often rely heavily on manual analysis and interpretation although new technologies and analytical procedures are available to automate workflows. Grade control is one such issue where the laboratory assay turn-around times cannot beat the shovel. We propose that for iron ore deposits in the Pilbara geophysical downhole logging may provide the necessary and sufficient information about rock formation properties, circumventing any need for real-time elemental analysis entirely. This study provides an example where petrophysical downhole data is automatically classified using a neuro-adaptive learning algorithm to differentiate between different rock types of iron ore deposits and for grade estimation. We exploit a rarely used ability in a spectral gamma-gamma density tool to gather both density and iron content with a single geophysical measurement. This inaccurate data is then put into a neural fuzzy inference system to classify the rock into different grades and waste lithologies, with success rates nearly equal to those from laboratory geochemistry. The steps outlined in this study may be used to produce a workflow for current logging tools and future logging-while-drilling technologies for real-time iron ore grade estimation and lithological classification.
- Open Access
- 1 September 2017
- Published by Australian Society of Exploration Geophysicists in Exploration Geophysics
- Vol. 48 (3) , 344-352
Testing cluster analysis on combined petrophysical and geochemical data for rock mass classification
New drilling, measurement-while-drilling and top-of-hole sensing technologies are being developed to overcome the challenges of exploration for new mineral deposits under deep cover. These methods will provide continuous, near-real time data collection from every drillhole in the future. Consequently, there will be a need for efficient methods of analysing and interpreting this data stream to complement the exploration strategy. We demonstrate the usefulness of cluster analysis for rapid, automated rock mass classification, and the impact of selecting different subsets of the available data on the classification results. Our study shows that only a few measurements are needed to broadly domain the intersected rock mass and highlights the importance of selecting correct input data depending on the purpose of the classification. Our analysis also indicates the potential of identifying textural and rock mechanical properties from petrophysical measurements via cluster analysis.
- 1 September 2017
- Published by Australian Society of Exploration Geophysicists in Exploration Geophysics
- Vol. 48 (3) , 344-352
Open AccessTesting cluster analysis on combined petrophysical and geochemical data for rock mass classification
New drilling, measurement-while-drilling and top-of-hole sensing technologies are being developed to overcome the challenges of exploration for new mineral deposits under deep cover. These methods will provide continuous, near-real time data collection from every drillhole in the future. Consequently, there will be a need for efficient methods of analysing and interpreting this data stream to complement the exploration strategy. We demonstrate the usefulness of cluster analysis for rapid, automated rock mass classification, and the impact of selecting different subsets of the available data on the classification results. Our study shows that only a few measurements are needed to broadly domain the intersected rock mass and highlights the importance of selecting correct input data depending on the purpose of the classification. Our analysis also indicates the potential of identifying textural and rock mechanical properties from petrophysical measurements via cluster analysis.
- 1 August 2017
- Published by Elsevier in International Journal of Greenhouse Gas Control
- Vol. 63, 150-157
4D surface seismic tracks small supercritical CO2 injection into the subsurface: CO2CRC Otway Project
- 1 August 2017
- Published by Elsevier in International Journal of Greenhouse Gas Control
- Vol. 63, 150-157
4D surface seismic tracks small supercritical CO2 injection into the subsurface: CO2CRC Otway Project