Wenwen Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Wenwen Li has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Srabanti Chowdhury
Department of Electrical and Computer Engineering, University of California at Davis, Davis, CA, USA
7 shared publications- Dong Ji
Department of Electrical and Computer Engineering, University of California at Davis, Davis, CA, USA
5 shared publications Anchal Agarwal
Department of Electrical and Computer Engineering, University of California at Santa Barbara, Santa Barbara, CA, USA
4 shared publicationsStacia Keller
Department of Electrical and Computer Engineering, University of California at Santa Barbara, Santa Barbara, CA, USA
4 shared publications- Chirag Gupta
Department of Electrical and Computer Engineering, University of Wisconsin-Madison , Madison, Wisconsin 53706
2 shared publications Haoran Li
Department of Electrical and Computer Engineering, University of California at Santa Barbara, Santa Barbara, CA, USA
2 shared publications
Latest Publications
- 4 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (12) , 5301-5306
Discrete-Pulsed Current Time Method to Estimate Channel Thermal Resistance of GaN-Based Power Devices
A simple electrical method to extract device channel thermal resistance in transistors is presented here. The method compares the dc to discrete-pulsed characteristics and estimates the effective increase in channel temperature under dc biasing conditions. Using the discrete-pulsed I versus t method, the self-heating of the device is effectively eliminated, which helps avoiding the underestimation of the device channel thermal resistance, therefore, making it possible to perform thermal measurements at the high power operation. This technique was applied to lateral GaN HEMTs with three different substrates as well as vertical GaN current aperture vertical electron transistor (CAVET) on sapphire, which proved its sensitivity and validity for different device structures and geometries.
- 4 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (12) , 5301-5306
Discrete-Pulsed Current Time Method to Estimate Channel Thermal Resistance of GaN-Based Power Devices
A simple electrical method to extract device channel thermal resistance in transistors is presented here. The method compares the dc to discrete-pulsed characteristics and estimates the effective increase in channel temperature under dc biasing conditions. Using the discrete-pulsed I versus t method, the self-heating of the device is effectively eliminated, which helps avoiding the underestimation of the device channel thermal resistance, therefore, making it possible to perform thermal measurements at the high power operation. This technique was applied to lateral GaN HEMTs with three different substrates as well as vertical GaN current aperture vertical electron transistor (CAVET) on sapphire, which proved its sensitivity and validity for different device structures and geometries.
- 22 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (10) , 4271-4275
A Study on the Impact of Channel Mobility on Switching Performance of Vertical GaN MOSFETs
This paper presents a comparison of switching performances between the in-situ oxide, gallium nitride (GaN) interlayer FET (OG-FET) and the conventional GaN metal-oxide-semiconductor FET (MOSFET), and explores the influence of the channel electron mobility on the device switching performance. GaN OG-FET is a novel structure with a pristine GaN layer grown between the gate oxide and the p-GaN enhancing the channel mobility up to 185 cm 2 /V· s, which is over 3× larger than that of the typical reported value (50 cm 2 /V · s) in GaN MOSFET. Owing to the high channel electron mobility, the GaN OG-FET showed a switching loss 30% lower than that of the conventional GaN trench MOSFET. Our results indicate that GaN OG-FET has the potential to attain greater efficiency, particularly at higher frequencies, showing a possible patch toward megahertz range conversions.
- 22 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (10) , 4271-4275
A Study on the Impact of Channel Mobility on Switching Performance of Vertical GaN MOSFETs
This paper presents a comparison of switching performances between the in-situ oxide, gallium nitride (GaN) interlayer FET (OG-FET) and the conventional GaN metal-oxide-semiconductor FET (MOSFET), and explores the influence of the channel electron mobility on the device switching performance. GaN OG-FET is a novel structure with a pristine GaN layer grown between the gate oxide and the p-GaN enhancing the channel mobility up to 185 cm 2 /V· s, which is over 3× larger than that of the typical reported value (50 cm 2 /V · s) in GaN MOSFET. Owing to the high channel electron mobility, the GaN OG-FET showed a switching loss 30% lower than that of the conventional GaN trench MOSFET. Our results indicate that GaN OG-FET has the potential to attain greater efficiency, particularly at higher frequencies, showing a possible patch toward megahertz range conversions.
- 4 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 39 (7) , 1030-1033
Improved Dynamic RON of GaN Vertical Trench MOSFETs (OG-FETs) Using TMAH Wet Etch
This letter reports on the dynamic $R_{\text{ON}}$ performance of large-area GaN vertical trench MOSFETs (OG-FETs) fabricated on bulk GaN substrates. OG-FETs demonstrated excellent DC performance with a breakdown voltage of 900 V and a $R_{\text{ON}}$ of 4.1 $\Omega$ (8.2 $\text{m}\Omega \cdot \text {cm}^{2}$ ). However, damage to the trench sidewalls caused by RIE dry etching led to poor dynamic $R_{\text{ON}}$ performance. An improved dynamic $R_{\text{ON}}$ performance was achieved by following the RIE dry etch with a TMAH wet etch. With this process combination, the dynamic $R_{\text{ON}}$ was reduced by more than 10 times compared with the dynamic $R_{\text{ON}}$ in devices fabricated by dry etch only.
- 4 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 39 (7) , 1030-1033
Improved Dynamic RON of GaN Vertical Trench MOSFETs (OG-FETs) Using TMAH Wet Etch
This letter reports on the dynamic $R_{\text{ON}}$ performance of large-area GaN vertical trench MOSFETs (OG-FETs) fabricated on bulk GaN substrates. OG-FETs demonstrated excellent DC performance with a breakdown voltage of 900 V and a $R_{\text{ON}}$ of 4.1 $\Omega$ (8.2 $\text{m}\Omega \cdot \text {cm}^{2}$ ). However, damage to the trench sidewalls caused by RIE dry etching led to poor dynamic $R_{\text{ON}}$ performance. An improved dynamic $R_{\text{ON}}$ performance was achieved by following the RIE dry etch with a TMAH wet etch. With this process combination, the dynamic $R_{\text{ON}}$ was reduced by more than 10 times compared with the dynamic $R_{\text{ON}}$ in devices fabricated by dry etch only.
- 20 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 39 (6) , 863-865
880 V/$2.7~\text{m}\Omega\cdot\text{cm}^{\text{2}}$ MIS Gate Trench CAVET on Bulk GaN Substrates
In this letter, we report a high-voltage metal-insulator-semiconductor (MIS) gate trench CAVET using MOCVD regrown AlGaN/GaN as the channel and in-situ Si3N4 as the gate dielectric. The device had a high breakdown voltage of 880 V and a low Ron,sp of 2.7 mΩ·cm2. A low hysteresis of ~ 0.1 V was observed due to the high quality of the in-situ Si3N4.
- 20 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 39 (6) , 863-865
880 V/$2.7~\text{m}\Omega\cdot\text{cm}^{\text{2}}$ MIS Gate Trench CAVET on Bulk GaN Substrates
In this letter, we report a high-voltage metal-insulator-semiconductor (MIS) gate trench CAVET using MOCVD regrown AlGaN/GaN as the channel and in-situ Si3N4 as the gate dielectric. The device had a high breakdown voltage of 880 V and a low Ron,sp of 2.7 mΩ·cm2. A low hysteresis of ~ 0.1 V was observed due to the high quality of the in-situ Si3N4.
- 8 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 39 (5) , 711-714
Large-Area In-Situ Oxide, GaN Interlayer-Based Vertical Trench MOSFET (OG-FET)
We present a large area in-situ oxide, GaN interlayer based vertical trench MOSFET (OG-FET) with an MOCVD regrown 10 nm UID-GaN interlayer as the channel and 50 nm in-situ Al2O3 as the gate dielectric. The threshold voltage of the device on bulk GaN substrate was 1 V measured at Ion/Ioff = 107. The OG-FET with an area scaled to 0.2 mm2 demonstrated a breakdown voltage (VBR) of 320 V and an on-state resistance (Ron)of 3.8 Ω(specific on-state resistance: Ron,sp= 7.6 mΩ∙cm2). For the single unit cell OG-FET from the same sample, VBR was as high as 700 V (measured at VGS = -10V), corresponding to a breakdown electric field of 1.4 MV/cm, and Ron,sp of 0.98 mΩ∙cm2. On our control sample was grown on sapphire substrate, a 1 A current was measured as well. These results show the potential of the OG-FET in power conversion applications.
- 8 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 39 (5) , 711-714
Large-Area In-Situ Oxide, GaN Interlayer-Based Vertical Trench MOSFET (OG-FET)
We present a large area in-situ oxide, GaN interlayer based vertical trench MOSFET (OG-FET) with an MOCVD regrown 10 nm UID-GaN interlayer as the channel and 50 nm in-situ Al2O3 as the gate dielectric. The threshold voltage of the device on bulk GaN substrate was 1 V measured at Ion/Ioff = 107. The OG-FET with an area scaled to 0.2 mm2 demonstrated a breakdown voltage (VBR) of 320 V and an on-state resistance (Ron)of 3.8 Ω(specific on-state resistance: Ron,sp= 7.6 mΩ∙cm2). For the single unit cell OG-FET from the same sample, VBR was as high as 700 V (measured at VGS = -10V), corresponding to a breakdown electric field of 1.4 MV/cm, and Ron,sp of 0.98 mΩ∙cm2. On our control sample was grown on sapphire substrate, a 1 A current was measured as well. These results show the potential of the OG-FET in power conversion applications.
- 9 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (2) , 483-487
Demonstration of GaN Current Aperture Vertical Electron Transistors With Aperture Region Formed by Ion Implantation
In this paper, we report the successful demonstration of current aperture vertical electron transistors (CAVETs) obtained by using a novel implantation-based compensation method to achieve a conductive aperture. This innovation leads to the first demonstration of ``regrowth-free'' CAVETs. Two gallium nitride (GaN) CAVETs were fabricated using the ion-implantation-compensated aperture regions, both with Mg-doped p-GaN as current-blocking layers (CBLs). The aperture regions were formed by implanting Si into the p-GaN CBL. In one of the CAVET samples, the Si-implantation-based aperture was formed prior to the regrowth of AlGaN/GaN layers on top. The other CAVET sample was subjected to aperture formation via Si implantation after all the device layers were grown. An ion-implantation scheme using multiple-energy levels was designed to realize a 250-nm Si box profile with a total dose of 4.2 x 10¹⁵ cm⁻², converting a 250-nm p-GaN (Mg: 8 x 10¹⁹ cm⁻²) to conductive (n-type) GaN successfully. This novel fabrication method enables the use of Mg-doped CBLs without conventional etch and regrowth steps. Moreover, the proposed scheme can ultimately lead to regrowth-free CAVETs.
- 9 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (2) , 483-487
Demonstration of GaN Current Aperture Vertical Electron Transistors With Aperture Region Formed by Ion Implantation
In this paper, we report the successful demonstration of current aperture vertical electron transistors (CAVETs) obtained by using a novel implantation-based compensation method to achieve a conductive aperture. This innovation leads to the first demonstration of ``regrowth-free'' CAVETs. Two gallium nitride (GaN) CAVETs were fabricated using the ion-implantation-compensated aperture regions, both with Mg-doped p-GaN as current-blocking layers (CBLs). The aperture regions were formed by implanting Si into the p-GaN CBL. In one of the CAVET samples, the Si-implantation-based aperture was formed prior to the regrowth of AlGaN/GaN layers on top. The other CAVET sample was subjected to aperture formation via Si implantation after all the device layers were grown. An ion-implantation scheme using multiple-energy levels was designed to realize a 250-nm Si box profile with a total dose of 4.2 x 10¹⁵ cm⁻², converting a 250-nm p-GaN (Mg: 8 x 10¹⁹ cm⁻²) to conductive (n-type) GaN successfully. This novel fabrication method enables the use of Mg-doped CBLs without conventional etch and regrowth steps. Moreover, the proposed scheme can ultimately lead to regrowth-free CAVETs.
- 10 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (5) , 600-603
High Voltage Diodes in Diamond Using (100)- and (111)- Substrates
We present a comparative study of PIN structures in diamond on type IIa (100)- and type IIb (111)-oriented bulk diamond substrates. An 8.5-μm thick i-layer demonstrated a blocking voltage>1kV for the (100)-oriented diamond sample without any mesa isolation, passivation, or edge termination structures. PIN diodes with a 530nm thick drift region, on the (111)-sample, demonstrated a blocking voltage of 207V at a current level of 1A/cm 2 with a corresponding blocking electric field of 3.9MV/cm. A deep ultraviolet light emission was observed only in (111)-diodes under forward bias, confirming well-behaved p-n junction characteristics in (111) as compared to (100).
- 10 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (5) , 600-603
High Voltage Diodes in Diamond Using (100)- and (111)- Substrates
We present a comparative study of PIN structures in diamond on type IIa (100)- and type IIb (111)-oriented bulk diamond substrates. An 8.5-μm thick i-layer demonstrated a blocking voltage>1kV for the (100)-oriented diamond sample without any mesa isolation, passivation, or edge termination structures. PIN diodes with a 530nm thick drift region, on the (111)-sample, demonstrated a blocking voltage of 207V at a current level of 1A/cm 2 with a corresponding blocking electric field of 3.9MV/cm. A deep ultraviolet light emission was observed only in (111)-diodes under forward bias, confirming well-behaved p-n junction characteristics in (111) as compared to (100).