Ricardo Gabriel de Almeida Mesquita
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ricardo Gabriel de Almeida Mesquita has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
Lourival Marin Mendes
Universidade Federal de Lavras, Brasil
11 shared publications- José Benedito Guimarães Júnior
Federal University of Lavras, Brazil
6 shared publications - Lourival Marin Mendes
Federal University of Lavras, Brazil
5 shared publications Antônia Amanda da Silva César
Federal University of Lavras, Brazil
4 shared publicationsJosé Manoel Marconcini
Brazilian Agricultural Research Corporation, Brazil
4 shared publicationsLina Bufalino
Federal University of Lavras
4 shared publications
Latest Publications
- Open Access
- 10 October 2026
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 84 (6) , 143
Bamboo particleboards bonded with lignin-modified vinyl acetate-ethylene adhesive: physical, mechanical, and thermal properties
The development of sustainable adhesive systems based on renewable resources is essential for advancing environmentally friendly lignocellulosic materials. However, limited information is available on the direct modification of vinyl acetate-ethylene (VAE) adhesives with Kraft lignin for bamboo particleboards, particularly regarding the relationship between adhesive thermal behavior, interfacial morphology, and panel performance. This study evaluated the effect of incorporating Kraft lignin (0, 5, 10, 15, and 20%) into VAE adhesive on the physical, mechanical, morphological, and thermal properties of bamboo particleboards. TGA/DTG and scanning electron microscopy (SEM) were used to investigate adhesive thermal behavior and particle–adhesive interfacial morphology, respectively. Lignin incorporation was associated with improved dimensional stability and mechanical performance. Water absorption decreased from 17.04% to 6.62% after 2 h and from 80.31% to 36.29% after 24 h. At 15% lignin, the modulus of rupture, modulus of elasticity, and internal bond increased from 38.02 to 60.45 MPa, 2219 to 5449 MPa, and 0.31 to 0.68 MPa, respectively. TGA/DTG showed that lignin did not substantially alter the overall degradation profile of VAE but increased carbonaceous residue at high temperatures. SEM revealed improved interfacial cohesion up to 15% lignin, with reduced fiber pull-out, fewer voids, and a more continuous adhesive matrix, whereas 20% lignin promoted agglomeration and microvacuole formation. Thermal conductivity remained stable at 0.13–0.15 W m⁻¹ K⁻¹. Among the formulations evaluated, 10 and 15% Kraft lignin showed the most favorable combination of dimensional stability and mechanical performance, demonstrating the potential of lignin as a renewable modifier for VAE-based bamboo particleboards.
- 10 October 2026
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 84 (6) , 143
Open AccessBamboo particleboards bonded with lignin-modified vinyl acetate-ethylene adhesive: physical, mechanical, and thermal properties
The development of sustainable adhesive systems based on renewable resources is essential for advancing environmentally friendly lignocellulosic materials. However, limited information is available on the direct modification of vinyl acetate-ethylene (VAE) adhesives with Kraft lignin for bamboo particleboards, particularly regarding the relationship between adhesive thermal behavior, interfacial morphology, and panel performance. This study evaluated the effect of incorporating Kraft lignin (0, 5, 10, 15, and 20%) into VAE adhesive on the physical, mechanical, morphological, and thermal properties of bamboo particleboards. TGA/DTG and scanning electron microscopy (SEM) were used to investigate adhesive thermal behavior and particle–adhesive interfacial morphology, respectively. Lignin incorporation was associated with improved dimensional stability and mechanical performance. Water absorption decreased from 17.04% to 6.62% after 2 h and from 80.31% to 36.29% after 24 h. At 15% lignin, the modulus of rupture, modulus of elasticity, and internal bond increased from 38.02 to 60.45 MPa, 2219 to 5449 MPa, and 0.31 to 0.68 MPa, respectively. TGA/DTG showed that lignin did not substantially alter the overall degradation profile of VAE but increased carbonaceous residue at high temperatures. SEM revealed improved interfacial cohesion up to 15% lignin, with reduced fiber pull-out, fewer voids, and a more continuous adhesive matrix, whereas 20% lignin promoted agglomeration and microvacuole formation. Thermal conductivity remained stable at 0.13–0.15 W m⁻¹ K⁻¹. Among the formulations evaluated, 10 and 15% Kraft lignin showed the most favorable combination of dimensional stability and mechanical performance, demonstrating the potential of lignin as a renewable modifier for VAE-based bamboo particleboards.
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 32
TECHNICAL AND ENVIRONMENTAL PERFORMANCE OF PARTICLEBOARDS FROM Erythrina poeppigiana (Walp.) O.F. Cook IN AGROFORESTRY SYSTEMS
Background: This study evaluated the technical performance, energy demand, and carbon footprint of particleboards produced from Erythrina poeppigiana (Walp.) O.F. Cook wood obtained from agroforestry systems, considering different panel densities and structural configurations. Results: Panel density significantly influenced both physical properties and environmental performance. Single-layer panels showed improved dimensional stability, with thickness swelling values below 22%, whereas multilayer panels exceeded this limit. Water absorption ranged from 40.1 to 78.4%, confirming the high hygroscopicity of the material. Mechanical performance was satisfactory, with modulus of elasticity ranging from 2062 to 2654 MPa, while modulus of rupture (18.6–23.7 MPa) and internal bond strength (0.49–0.80 MPa) showed no significant differences among treatments. In the cradle-to-gate assessment, energy demand ranged from 4649 to 4869 MJ·m⁻³ and CO₂e emissions from 189.89 to 203.06 kg CO₂e·m⁻³. Lower-density panels showed the lowest environmental impacts due to reduced wood and adhesive consumption. Adhesive production was the main contributor, accounting for approximately 72–74% of total emissions. Conclusion: E. poeppigiana wood from agroforestry systems is a viable alternative raw material for particleboard production. Panel structure and material efficiency were the main factors controlling performance and environmental impacts. High water absorption values (40.1–78.4%) represent a critical limitation, compromising dimensional stability and restricting multilayer configurations under moisture exposure. Improvements in dimensional stability are still required.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 32
Open AccessTECHNICAL AND ENVIRONMENTAL PERFORMANCE OF PARTICLEBOARDS FROM Erythrina poeppigiana (Walp.) O.F. Cook IN AGROFORESTRY SYSTEMS
Background: This study evaluated the technical performance, energy demand, and carbon footprint of particleboards produced from Erythrina poeppigiana (Walp.) O.F. Cook wood obtained from agroforestry systems, considering different panel densities and structural configurations. Results: Panel density significantly influenced both physical properties and environmental performance. Single-layer panels showed improved dimensional stability, with thickness swelling values below 22%, whereas multilayer panels exceeded this limit. Water absorption ranged from 40.1 to 78.4%, confirming the high hygroscopicity of the material. Mechanical performance was satisfactory, with modulus of elasticity ranging from 2062 to 2654 MPa, while modulus of rupture (18.6–23.7 MPa) and internal bond strength (0.49–0.80 MPa) showed no significant differences among treatments. In the cradle-to-gate assessment, energy demand ranged from 4649 to 4869 MJ·m⁻³ and CO₂e emissions from 189.89 to 203.06 kg CO₂e·m⁻³. Lower-density panels showed the lowest environmental impacts due to reduced wood and adhesive consumption. Adhesive production was the main contributor, accounting for approximately 72–74% of total emissions. Conclusion: E. poeppigiana wood from agroforestry systems is a viable alternative raw material for particleboard production. Panel structure and material efficiency were the main factors controlling performance and environmental impacts. High water absorption values (40.1–78.4%) represent a critical limitation, compromising dimensional stability and restricting multilayer configurations under moisture exposure. Improvements in dimensional stability are still required.
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 32, e103675
The effect of cellulose nanocrystals on the properties of Erythrina poeppigiana (Walp.) O.F. Cook plywood
Background: Erythrina poeppigiana is a fast-growing, low density tropical wood species underutilized in southern Bahia, Brazil. Its plywood exhibits limited mechanical performance due to wide parenchyma bands, low lignin content, and high porosity. Cellulose nanocrystals (NCC) have been proposed as reinforcement to enhance panel stiffness and modify adhesive behavior. This study evaluated the effects of incorporating NCC into phenol-formaldehyde adhesive (PF) on the physical and mechanical properties of E. poeppigiana plywood. Results: Plywood panels were produced with NCC loadings of 0, 1, 1.5, and 2% based on the total mass of the PF adhesive. NCC addition increased the parallel modulus of elasticity from 4651 MPa in the control to 6076 MPa at 2% NCC (≈31% increase), allowing the panels to reach the minimum requirement for concrete formwork plywood. No significant effect was observed on modulus of rupture. Water absorption and 24-hour thickness swelling increased with NCC, reflecting the hydrophilic nature of NCC and the wood’s anatomical structure. Shear strength decreased at higher NCC contents, particularly above 1%, likely due to increased adhesive viscosity and reduced spreading caused by NCC–polymer interactions. Other properties, including density and moisture content, remained unaffected. Conclusion: NCC incorporation improved the stiffness of E. poeppigiana plywood; however, higher concentrations negatively affect bonding performance and moisture-related properties. The wood’s chemical and anatomical characteristics, notably broad parenchyma bands and low density, influence the overall performance. These findings suggest that controlled NCC incorporation offers a strategy to enhance value-added applications of underutilized species.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 32, e103675
Open AccessThe effect of cellulose nanocrystals on the properties of Erythrina poeppigiana (Walp.) O.F. Cook plywood
Background: Erythrina poeppigiana is a fast-growing, low density tropical wood species underutilized in southern Bahia, Brazil. Its plywood exhibits limited mechanical performance due to wide parenchyma bands, low lignin content, and high porosity. Cellulose nanocrystals (NCC) have been proposed as reinforcement to enhance panel stiffness and modify adhesive behavior. This study evaluated the effects of incorporating NCC into phenol-formaldehyde adhesive (PF) on the physical and mechanical properties of E. poeppigiana plywood. Results: Plywood panels were produced with NCC loadings of 0, 1, 1.5, and 2% based on the total mass of the PF adhesive. NCC addition increased the parallel modulus of elasticity from 4651 MPa in the control to 6076 MPa at 2% NCC (≈31% increase), allowing the panels to reach the minimum requirement for concrete formwork plywood. No significant effect was observed on modulus of rupture. Water absorption and 24-hour thickness swelling increased with NCC, reflecting the hydrophilic nature of NCC and the wood’s anatomical structure. Shear strength decreased at higher NCC contents, particularly above 1%, likely due to increased adhesive viscosity and reduced spreading caused by NCC–polymer interactions. Other properties, including density and moisture content, remained unaffected. Conclusion: NCC incorporation improved the stiffness of E. poeppigiana plywood; however, higher concentrations negatively affect bonding performance and moisture-related properties. The wood’s chemical and anatomical characteristics, notably broad parenchyma bands and low density, influence the overall performance. These findings suggest that controlled NCC incorporation offers a strategy to enhance value-added applications of underutilized species.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 31
Partial replacement of tannin with nanolignin in adhesive formulations for bonding plywood produced with Erythrina poeppigiana wood
Background: Fast-growing species are crucial for the wood panel market, and Erythrina poeppigiana (mulungu) emerges as a promising alternative. Although its wood is not suitable for high-performance applications, using its veneers for plywood supports the diversification of raw materials in forestry. Furthermore, replacing petrochemical-based adhesives is essential due to associated health and environmental risks. Tannins from forest species provide a sustainable alternative; however, their mechanical strength and moisture resistance must be improved. Nanolignin, a nanoscale additive, enhances these properties, making it a viable option for biodegradable adhesives. This study evaluates plywood production using E. poeppigiana veneers bonded with a tannin-nanolignin adhesive. Results: Adhesives were formulated with Acacia mearnsii* tannin partially replaced by nanolignin at different concentrations and tested for rheological properties. The wood, sourced from experimental plantations in Ilhéus, Bahia (Brazil), was processed into five-layer plywood panels bonded with 320 g/m² of natural adhesive and pressed at 150 °C and 1 MPa for 10 minutes. The resulting panels were evaluated for physical and mechanical properties, contact angle, scanning electron microscopy (SEM), acoustic insulation, and thermal conductivity. The results confirmed E. poeppigiana as a viable raw material for plywood production. Partial replacement of tannin with 1-2% nanolignin reduced adhesive viscosity, improving application and veneer penetration. The 2% nanolignin formulation increased hydrophobicity, reducing water absorption, while shear strength tests revealed higher cohesion and adhesion, particularly in adhesives containing 2-3% nanolignin. Conclusions: The findings demonstrate that E. poeppigiana veneers bonded with tannin-nanolignin adhesives can produce plywood panels with suitable physical and mechanical performance. The incorporation of small amounts of nanolignin enhances the adhesive’s rheological and bonding characteristics, contributing to improved durability and water resistance. These results support the potential use of E. poeppigian and nanolignin-modified tannins as sustainable materials in eco-friendly plywood manufacturing.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 31
Open AccessPartial replacement of tannin with nanolignin in adhesive formulations for bonding plywood produced with Erythrina poeppigiana wood
Background: Fast-growing species are crucial for the wood panel market, and Erythrina poeppigiana (mulungu) emerges as a promising alternative. Although its wood is not suitable for high-performance applications, using its veneers for plywood supports the diversification of raw materials in forestry. Furthermore, replacing petrochemical-based adhesives is essential due to associated health and environmental risks. Tannins from forest species provide a sustainable alternative; however, their mechanical strength and moisture resistance must be improved. Nanolignin, a nanoscale additive, enhances these properties, making it a viable option for biodegradable adhesives. This study evaluates plywood production using E. poeppigiana veneers bonded with a tannin-nanolignin adhesive. Results: Adhesives were formulated with Acacia mearnsii* tannin partially replaced by nanolignin at different concentrations and tested for rheological properties. The wood, sourced from experimental plantations in Ilhéus, Bahia (Brazil), was processed into five-layer plywood panels bonded with 320 g/m² of natural adhesive and pressed at 150 °C and 1 MPa for 10 minutes. The resulting panels were evaluated for physical and mechanical properties, contact angle, scanning electron microscopy (SEM), acoustic insulation, and thermal conductivity. The results confirmed E. poeppigiana as a viable raw material for plywood production. Partial replacement of tannin with 1-2% nanolignin reduced adhesive viscosity, improving application and veneer penetration. The 2% nanolignin formulation increased hydrophobicity, reducing water absorption, while shear strength tests revealed higher cohesion and adhesion, particularly in adhesives containing 2-3% nanolignin. Conclusions: The findings demonstrate that E. poeppigiana veneers bonded with tannin-nanolignin adhesives can produce plywood panels with suitable physical and mechanical performance. The incorporation of small amounts of nanolignin enhances the adhesive’s rheological and bonding characteristics, contributing to improved durability and water resistance. These results support the potential use of E. poeppigian and nanolignin-modified tannins as sustainable materials in eco-friendly plywood manufacturing.
- Open Access
- 1 December 2024
- Published by FapUNIFESP (SciELO) in Ambiente Construído
- Vol. 24, e132136
Sustainable use of Erythrina poeppigiana in formaldehyde-free plywood: environmental and energy analysis
The study analyzed the technical and environmental feasibility of using Erythrina poeppigiana to produce plywood with different adhesives: phenol-formaldehyde (PF), urea-formaldehyde (UF), and castor oil-based polyurethane (PUA). The physical and mechanical properties of the plywood were evaluated, including apparent density, moisture content, water absorption, thickness swelling, shear resistance, and static bending. Tests proved erythrina’s suitability for non-structural plywood production. The environmental impact of the production process was also evaluated, using embedded energy and CO2e emissions as indicators. The results showed that plywood produced with PU adhesive had better environmental performance compared to panels with FF and UF adhesives. T1 treatment (PF) had the highest embodied energy, while T2 (UF) had the highest CO2e emission. Overall, the study suggests that using erythrina to produce plywood can be a viable option for promoting regional socioeconomic development while also being environmentally sustainable and presents an advantage over foreign plywood in terms of environmental performance.
- 1 December 2024
- Published by FapUNIFESP (SciELO) in Ambiente Construído
- Vol. 24, e132136
Open AccessSustainable use of Erythrina poeppigiana in formaldehyde-free plywood: environmental and energy analysis
The study analyzed the technical and environmental feasibility of using Erythrina poeppigiana to produce plywood with different adhesives: phenol-formaldehyde (PF), urea-formaldehyde (UF), and castor oil-based polyurethane (PUA). The physical and mechanical properties of the plywood were evaluated, including apparent density, moisture content, water absorption, thickness swelling, shear resistance, and static bending. Tests proved erythrina’s suitability for non-structural plywood production. The environmental impact of the production process was also evaluated, using embedded energy and CO2e emissions as indicators. The results showed that plywood produced with PU adhesive had better environmental performance compared to panels with FF and UF adhesives. T1 treatment (PF) had the highest embodied energy, while T2 (UF) had the highest CO2e emission. Overall, the study suggests that using erythrina to produce plywood can be a viable option for promoting regional socioeconomic development while also being environmentally sustainable and presents an advantage over foreign plywood in terms of environmental performance.
- 5 August 2020
- Published by Springer Nature in Journal of Polymer Research
- Vol. 27 (9) , 1-13
Production of castor oil-based polyurethane resin composites reinforced with coconut husk fibres
- 5 August 2020
- Published by Springer Nature in Journal of Polymer Research
- Vol. 27 (9) , 1-13
Production of castor oil-based polyurethane resin composites reinforced with coconut husk fibres
- Open Access
- 1 June 2019
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 25 (2) , 203-213
THE EFFECT OF CELLULOSE NANOCRYSTALS IN SUGARCANE BAGASSE PARTICLEBOARDS OF PITH AND FIBERS
The aim of this research was to investigate sugarcane bagasse (SCB) particleboards, using two kinds of particles, from pith and fibers, reinforced with cellulose nanocrystals (NCC). The NCCs were dispersed in the adhesive urea formaldehyde (UF) using a sonificator in two proportions (0 and 1%). The NCCs and UF were applied in the SCB particles using a rotary blender. The particleboards were produced in three layers using two kinds of particles: pith and fibers. After dispersion of the adhesive, the mixture was compressed to produce the particleboards, which were characterized by physical, mechanical and thermal properties. The anatomical and chemical features relating to pith and fiber were very similar. The particleboards made with and without NCCs did not differ statistically for most properties: modulus of elasticity (MOE), modulus of rupture (MOR), water absorption (WA) thermal conductivity (TC), and the volume heat capacity (VHC). Particleboards made only with fibers and without NCCs showed higher internal bond (IB). In the other hand particleboards made only with fibers in the face and pith in the core (without NCCs) showed lower thickness swelling after 24 hours (TS24h). Probably, the NCCs did not improve the particleboards performance, because less links were available for SCB to interact with the adhesive. For the others properties the particleboards made with pith and fibers did not showed statistical difference (MOE, MOR, TC, WA, TC and VHC), demonstrating that separation of pith and fiber are not significant and does not affect the final properties of particleboards.
- 1 June 2019
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 25 (2) , 203-213
Open AccessTHE EFFECT OF CELLULOSE NANOCRYSTALS IN SUGARCANE BAGASSE PARTICLEBOARDS OF PITH AND FIBERS
The aim of this research was to investigate sugarcane bagasse (SCB) particleboards, using two kinds of particles, from pith and fibers, reinforced with cellulose nanocrystals (NCC). The NCCs were dispersed in the adhesive urea formaldehyde (UF) using a sonificator in two proportions (0 and 1%). The NCCs and UF were applied in the SCB particles using a rotary blender. The particleboards were produced in three layers using two kinds of particles: pith and fibers. After dispersion of the adhesive, the mixture was compressed to produce the particleboards, which were characterized by physical, mechanical and thermal properties. The anatomical and chemical features relating to pith and fiber were very similar. The particleboards made with and without NCCs did not differ statistically for most properties: modulus of elasticity (MOE), modulus of rupture (MOR), water absorption (WA) thermal conductivity (TC), and the volume heat capacity (VHC). Particleboards made only with fibers and without NCCs showed higher internal bond (IB). In the other hand particleboards made only with fibers in the face and pith in the core (without NCCs) showed lower thickness swelling after 24 hours (TS24h). Probably, the NCCs did not improve the particleboards performance, because less links were available for SCB to interact with the adhesive. For the others properties the particleboards made with pith and fibers did not showed statistical difference (MOE, MOR, TC, WA, TC and VHC), demonstrating that separation of pith and fiber are not significant and does not affect the final properties of particleboards.
- Open Access
- 1 March 2018
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 24 (1) , 1-8
POLYESTER COMPOSITES REINFORCED WITH MALEIC ANHYDRIDE-TREATED FILAMENTS FROM MAUVE
The objective of this study was to evaluate the polyester-based fiber composites reinfor ced with filaments/fibers of mauve treated with NaOH and maleic anhydride. The che mical treatment of the mauve filament/fibers (3 cm of length) was carried out, first with NaOH, followed by maleic anhydride. The resin used was ortho unsaturated polyester with addition of catalyst peroxide methyl ethyl ketone. The composites were prepared with 15% filaments (w/w) and tested for water absorption, three-point bending, tensile and impact strength. Fiberglass composites were produced using the same methodology for comparison purpose. The results demonstrate the potential use of mauve filaments. For some properties, the mauve composites showed better mechanical properties than fiberglass composites (three-point bending and tensile). The treatment of the filaments had varied effect and did not improve the mechanical properties. However, for the water absorption was observed a reduction of 35% in composites with treated mauve filaments.
- 1 March 2018
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 24 (1) , 1-8
Open AccessPOLYESTER COMPOSITES REINFORCED WITH MALEIC ANHYDRIDE-TREATED FILAMENTS FROM MAUVE
The objective of this study was to evaluate the polyester-based fiber composites reinfor ced with filaments/fibers of mauve treated with NaOH and maleic anhydride. The che mical treatment of the mauve filament/fibers (3 cm of length) was carried out, first with NaOH, followed by maleic anhydride. The resin used was ortho unsaturated polyester with addition of catalyst peroxide methyl ethyl ketone. The composites were prepared with 15% filaments (w/w) and tested for water absorption, three-point bending, tensile and impact strength. Fiberglass composites were produced using the same methodology for comparison purpose. The results demonstrate the potential use of mauve filaments. For some properties, the mauve composites showed better mechanical properties than fiberglass composites (three-point bending and tensile). The treatment of the filaments had varied effect and did not improve the mechanical properties. However, for the water absorption was observed a reduction of 35% in composites with treated mauve filaments.
- 2 February 2018
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 26 (7) , 3040-3050
Urea Formaldehyde and Cellulose Nanocrystals Adhesive: Studies Applied to Sugarcane Bagasse Particleboards
- 2 February 2018
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 26 (7) , 3040-3050
Urea Formaldehyde and Cellulose Nanocrystals Adhesive: Studies Applied to Sugarcane Bagasse Particleboards
- Open Access
- 20 October 2016
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 19 (6) , 1429-1436
Coir and Sisal Fibers as Fillers in the Production of Eucalyptus Medium Density Particleboards - MDP
The aim of this study was to evaluate the potential use of sisal and coir fibers in combination with Eucalyptus particles for the production of particleboard. The particleboards were produced in three layers. The first and third layers (face) were made with small Eucalyptus particles. The second layer (core) was made with big Eucalyptus particles in combination with coir or sisal fibers. The particleboards were prepared with the substitution on Eucalyptus wood for sisal and coir fibers in the particleboards core, in doses of 0, 10, and 20%, relative to the total mass of particles. The particleboards were characterized by mechanical, physical and thermal properties. The results were not satisfactory for particleboards with sisal. However, for coir particleboards the physical-mechanical properties were very similar to those particleboards produced only with Eucalyptus. This work demonstrates the potential use of the coir that is commonly disposed in landfills on the Brazilian beaches.
- 20 October 2016
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 19 (6) , 1429-1436
Open AccessCoir and Sisal Fibers as Fillers in the Production of Eucalyptus Medium Density Particleboards - MDP
The aim of this study was to evaluate the potential use of sisal and coir fibers in combination with Eucalyptus particles for the production of particleboard. The particleboards were produced in three layers. The first and third layers (face) were made with small Eucalyptus particles. The second layer (core) was made with big Eucalyptus particles in combination with coir or sisal fibers. The particleboards were prepared with the substitution on Eucalyptus wood for sisal and coir fibers in the particleboards core, in doses of 0, 10, and 20%, relative to the total mass of particles. The particleboards were characterized by mechanical, physical and thermal properties. The results were not satisfactory for particleboards with sisal. However, for coir particleboards the physical-mechanical properties were very similar to those particleboards produced only with Eucalyptus. This work demonstrates the potential use of the coir that is commonly disposed in landfills on the Brazilian beaches.