Johng-Hwa Ahn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Johng-Hwa Ahn has a total of 77 co-authors. Here are the top co-authors by number of shared publications:
Seung Gu Shin
Gyeongsang National Univ
4 shared publications- Jang-Hyun Kang
Department of Environmental Engineering, College of Engineering, Kangwon National University, Chuncheon, Korea
3 shared publications Min-Woo Byeon
3 shared publicationsEui Jeong Noh
Department of Integrated Energy and Infra System, Kangwon National University, Chuncheon, Korea
2 shared publicationsEun-Young Jo
Department of Environmental Engineering, College of Engineering, Kangwon National University, Chuncheon 200-701, Korea
2 shared publicationsKyung-Min Kim
Department of Integrated Energy and Infra System, Kangwon National University, Chuncheon, Gangwon-do, 24341, South Korea
2 shared publications
Latest Publications
- Open Access
- 6 October 2026
- Published by Elsevier in SSRN Electronic Journal
Identification and Quantitative Analysis of Phenolic Compounds in Industrial Waste in the Republic of Korea
An analysis method for phenolic compounds in waste was developed, and its contents and leaching concentrations were measured to investigate the concentration and distribution of phenolic compounds in waste in South Korea. The EPA 8041 method was applied; thirteen phenolic compounds were derivatized and analyzed simultaneously using pentafluorobenzylbromide (PFBBr). Leaching pretreatment was performed using Korea’s leaching test method. For content pretreatment, extraction and derivatization were performed by applying EPA 3550C. An analysis was conducted using GC-MS. Fifty samples were collected from industrial waste in Korea, and six waste types (wastewater sludge, organic sludge, process sludge, waste foundry sand, waste soil, and waste sand) were selected for research. In the analysis results, seven phenolic compounds (2-Chlorophenol, 4-Chloro-3-methylphenol, 2,4-Dichlorophenol, 2,6-Dichlorophenol, 2,4,5-Trichlorophenol, 2,4,6-Trichlorophenol, and 2,3,4,6- Trichlorophenol) were not detected in the samples. When leachate was analyzed, organic sludge exhibited the highest total phenolic compound content of 18.8 mg/L, with nonylphenols (NPs, 14.4 mg/L) and p-Cresol (0.4 mg/L) showing the highest concentrations. In the content analysis results, the highest total phenolic compound content of 119.3 mg/kg was detected from wastewater sludge with bisphenol A (43.8 mg/kg), phenol (27.8 mg/kg), pentachlorophenol (18.1 mg/kg), o-Cresol (2.8 mg/kg), and m-Cresol (0.5 mg/kg) exhibiting the highest concentrations. When the analysis results were compared with domestic and overseas recycling criteria, the leachate criterion (1 mg/L) was exceeded by 17 samples out of 50, whereas the content criterion (4 mg/kg) was exceeded by 26 samples. This indicates that it is necessary to prepare countermeasures regarding emission source management.
- 6 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessIdentification and Quantitative Analysis of Phenolic Compounds in Industrial Waste in the Republic of Korea
An analysis method for phenolic compounds in waste was developed, and its contents and leaching concentrations were measured to investigate the concentration and distribution of phenolic compounds in waste in South Korea. The EPA 8041 method was applied; thirteen phenolic compounds were derivatized and analyzed simultaneously using pentafluorobenzylbromide (PFBBr). Leaching pretreatment was performed using Korea’s leaching test method. For content pretreatment, extraction and derivatization were performed by applying EPA 3550C. An analysis was conducted using GC-MS. Fifty samples were collected from industrial waste in Korea, and six waste types (wastewater sludge, organic sludge, process sludge, waste foundry sand, waste soil, and waste sand) were selected for research. In the analysis results, seven phenolic compounds (2-Chlorophenol, 4-Chloro-3-methylphenol, 2,4-Dichlorophenol, 2,6-Dichlorophenol, 2,4,5-Trichlorophenol, 2,4,6-Trichlorophenol, and 2,3,4,6- Trichlorophenol) were not detected in the samples. When leachate was analyzed, organic sludge exhibited the highest total phenolic compound content of 18.8 mg/L, with nonylphenols (NPs, 14.4 mg/L) and p-Cresol (0.4 mg/L) showing the highest concentrations. In the content analysis results, the highest total phenolic compound content of 119.3 mg/kg was detected from wastewater sludge with bisphenol A (43.8 mg/kg), phenol (27.8 mg/kg), pentachlorophenol (18.1 mg/kg), o-Cresol (2.8 mg/kg), and m-Cresol (0.5 mg/kg) exhibiting the highest concentrations. When the analysis results were compared with domestic and overseas recycling criteria, the leachate criterion (1 mg/L) was exceeded by 17 samples out of 50, whereas the content criterion (4 mg/kg) was exceeded by 26 samples. This indicates that it is necessary to prepare countermeasures regarding emission source management.
- 1 February 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Environmental Engineering
- Vol. 152 (2)
Quantitative Standardization of Preincubation for Reliable Biochemical Methane Potential
- 1 February 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Environmental Engineering
- Vol. 152 (2)
Quantitative Standardization of Preincubation for Reliable Biochemical Methane Potential
- Open Access
- 1 January 2026
- Published by Korean Society of Environmental Engineering in Journal of Korean Society of Environmental Engineers
- Vol. 48 (1) , 1-8
Response Surface Optimization of Turbidity Removal Using Plant-Based Mixed Coagulant
Optimal conditions for turbidity removal from synthetic wastewater were investigated using a mixed plant-based coagulant. Synthetic wastewater was prepared by suspending kaolin powder in distilled water and adjusting the final turbidity to 500 NTU. The mixed coagulant was prepared by extracting Clerodendrum powders and cactus powders in a 0.5mol/L NaCl solution followed by filtration. The experimental ranges of the key factors were pH 3-8, coagulant dosage 30-120mg/L, and cactus ratio 30-90%. A face-centered response surface design was employed to evaluate factor interactions and to determine the optimal conditions. In the single-factor experiments, the highest turbidity removal efficiency (96%) was obtained at pH 3, and the efficiency progressively decreased with increasing pH. The maximum removal efficiency was 84% at 90mg/L of dosage and 78% at 50% of cactus ratio. In the response surface analysis, all independent variables significantly influenced turbidity removal (p< 0.05), with pH (p<0.001) and dosage (p<0.001) exerting stronger effects than the cactus ratio (p=0.006). Significant two-way interactions were observed for pH × dosage (p=0.005) and pH × cactus ratio (p=0.006). The response surface model (R2=0.93) predicted optimal conditions of pH 3.0, dosage 75 mg/L, and cactus ratio 65%, yielding a predicted turbidity removal efficiency exceeding 99.9%. These findings demonstrate that Clerodendrum (charge neutralization) and cactus (bridging effect) act synergistically, providing enhanced turbidity removal performance and overcoming the limitations of single plant-based coagulants.
- 1 January 2026
- Published by Korean Society of Environmental Engineering in Journal of Korean Society of Environmental Engineers
- Vol. 48 (1) , 1-8
Open AccessResponse Surface Optimization of Turbidity Removal Using Plant-Based Mixed Coagulant
Optimal conditions for turbidity removal from synthetic wastewater were investigated using a mixed plant-based coagulant. Synthetic wastewater was prepared by suspending kaolin powder in distilled water and adjusting the final turbidity to 500 NTU. The mixed coagulant was prepared by extracting Clerodendrum powders and cactus powders in a 0.5mol/L NaCl solution followed by filtration. The experimental ranges of the key factors were pH 3-8, coagulant dosage 30-120mg/L, and cactus ratio 30-90%. A face-centered response surface design was employed to evaluate factor interactions and to determine the optimal conditions. In the single-factor experiments, the highest turbidity removal efficiency (96%) was obtained at pH 3, and the efficiency progressively decreased with increasing pH. The maximum removal efficiency was 84% at 90mg/L of dosage and 78% at 50% of cactus ratio. In the response surface analysis, all independent variables significantly influenced turbidity removal (p< 0.05), with pH (p<0.001) and dosage (p<0.001) exerting stronger effects than the cactus ratio (p=0.006). Significant two-way interactions were observed for pH × dosage (p=0.005) and pH × cactus ratio (p=0.006). The response surface model (R2=0.93) predicted optimal conditions of pH 3.0, dosage 75 mg/L, and cactus ratio 65%, yielding a predicted turbidity removal efficiency exceeding 99.9%. These findings demonstrate that Clerodendrum (charge neutralization) and cactus (bridging effect) act synergistically, providing enhanced turbidity removal performance and overcoming the limitations of single plant-based coagulants.
- Open Access
- 1 December 2025
- Published by Korean Society of Environmental Engineering in Journal of Korean Society of Environmental Engineers
- Vol. 47 (12) , 776-785
Removal of Methylene Blue Using Agricultural Waste Biomass: A Comparative Study of Corncob, Rice Husk, and Walnut Shell
Industrial dye effluents have been identified as a substantial contributor to water contamination. In order to achieve the efficient removal of methylene blue (MB) using accessible and low-cost sorbents, a comparison was made of the removal performance of agricultural-waste biomass, including corncob, rice husk, and walnut shell. Without pretreatment, batch adsorption experiments were conducted for reaction times of 1-80 min at dosages of 2.5-7.5g/L with an initial MB concentration of 100mg/L. The suspensions were subjected to agitation with a jar tester at a frequency of 150 rpm, followed by a centrifugation step at 4,000 rpm for 10 min. The concentration of MB was subsequently quantified at a wavelength of 664 nm utilizing an ultraviolet-visible spectrophotometer. The maximum removal efficiencies were 99.2±0.04% with corncob, 97.4±0.61% with rice husk, and 94.1±1.48% with walnut shell at 80 min and 7.5g/L. Isotherm analysis revealed higher coefficient of determination (R2) for the Langmuir model (0.98-0.99) in comparison to the Freundlich model (0.94-0.96), suggesting that MB adsorption is more accurately represented by monolayer coverage on homogeneous sites. The findings of the kinetic analysis demonstrated that the pseudo-second-order kinetic model (R2 = 0.9985-1.0000) yielded a superior fit to all biomass in comparison to the pseudo-first-order kinetic model (R2 =0.003-0.932). This finding indicates that the pseudo-second-order kinetic model provides a superior description of the adsorption rates of the tested biomass. The Fourier-transform infrared analysis revealed the presence of characteristic functional groups of lignocellulosic biomass, including cellulose, hemicellulose, and lignin, across all sorbents. The overall peak intensities followed the order corncob>rice husk>walnut shell, which is consistent with the observed relative MB adsorption performance. Consequently, corncob, rice husk, and walnut shell biomass, in that order, were the most effective for MB removal in this study.
- 1 December 2025
- Published by Korean Society of Environmental Engineering in Journal of Korean Society of Environmental Engineers
- Vol. 47 (12) , 776-785
Open AccessRemoval of Methylene Blue Using Agricultural Waste Biomass: A Comparative Study of Corncob, Rice Husk, and Walnut Shell
Industrial dye effluents have been identified as a substantial contributor to water contamination. In order to achieve the efficient removal of methylene blue (MB) using accessible and low-cost sorbents, a comparison was made of the removal performance of agricultural-waste biomass, including corncob, rice husk, and walnut shell. Without pretreatment, batch adsorption experiments were conducted for reaction times of 1-80 min at dosages of 2.5-7.5g/L with an initial MB concentration of 100mg/L. The suspensions were subjected to agitation with a jar tester at a frequency of 150 rpm, followed by a centrifugation step at 4,000 rpm for 10 min. The concentration of MB was subsequently quantified at a wavelength of 664 nm utilizing an ultraviolet-visible spectrophotometer. The maximum removal efficiencies were 99.2±0.04% with corncob, 97.4±0.61% with rice husk, and 94.1±1.48% with walnut shell at 80 min and 7.5g/L. Isotherm analysis revealed higher coefficient of determination (R2) for the Langmuir model (0.98-0.99) in comparison to the Freundlich model (0.94-0.96), suggesting that MB adsorption is more accurately represented by monolayer coverage on homogeneous sites. The findings of the kinetic analysis demonstrated that the pseudo-second-order kinetic model (R2 = 0.9985-1.0000) yielded a superior fit to all biomass in comparison to the pseudo-first-order kinetic model (R2 =0.003-0.932). This finding indicates that the pseudo-second-order kinetic model provides a superior description of the adsorption rates of the tested biomass. The Fourier-transform infrared analysis revealed the presence of characteristic functional groups of lignocellulosic biomass, including cellulose, hemicellulose, and lignin, across all sorbents. The overall peak intensities followed the order corncob>rice husk>walnut shell, which is consistent with the observed relative MB adsorption performance. Consequently, corncob, rice husk, and walnut shell biomass, in that order, were the most effective for MB removal in this study.
- 15 October 2025
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 17 (7) , 3835-3843
Anaerobic Co-digestion of Fish Waste and Primary Sludge: Biochemical Methane Potential and Mixing Ratio
- 15 October 2025
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 17 (7) , 3835-3843
Anaerobic Co-digestion of Fish Waste and Primary Sludge: Biochemical Methane Potential and Mixing Ratio
- 22 April 2025
- Published by Elsevier in Bioresource Technology
- Vol. 430, 132568
Optimization of synergistic microwave and zero–valent iron co–pretreatment for anaerobic digestion of waste activated sludge
- 22 April 2025
- Published by Elsevier in Bioresource Technology
- Vol. 430, 132568
Optimization of synergistic microwave and zero–valent iron co–pretreatment for anaerobic digestion of waste activated sludge
- Open Access
- 1 February 2025
- Published by Korean Society of Environmental Engineering in Journal of Korean Society of Environmental Engineers
- Vol. 47 (2) , 98-109
Extraction of Chitin from Shrimp Shells using Microwave: Optimization of Protein Removal based on Central Composite Face-centered Design
The objective of this study is to extract chitin from shrimp shells by removing minerals and proteins using a microwave heating method. The optimal conditions for protein removal were proposed using response surface analysis. Experiments on mineral removal were conducted under discontinuous conditions with irradiation time (1~5 min), temperature (90~130℃), and irradiation power (400~1,600 W). Following the mineral removal process, protein removal experiments were performed under discontinuous conditions with irradiation time (1~10 min), temperature (40~100℃), and irradiation power (400~1,600 W). To identify the optimal points and interactions between factors for protein removal on a continuous scale, the central composite face-centered design, a type of response surface analysis, was employed. Independent variables were set as temperature (40~100℃) and irradiation power (600~1,600 W). Under discontinuous conditions, mineral removal experiments resulted in over 99.9% mineral removal efficiency at 3 min, 100℃, and 1,600 W. For protein removal, maximum efficiency of 94.9% was observed at 3 min, 40℃, and 1,600 W. Lower temperatures resulted in higher protein removal efficiency. Higher irradiation power led to increased protein removal efficiency. The optimal conditions for protein removal in continuous scale experiments were found to be 40℃ and 1,600 W. Under these conditions, a removal efficiency of 95% was achieved. All independent variables significantly influenced the removal process using microwave heating, with p<0.05. The chitin extracted in this experiment exhibited an α-chitin structure with a crystallinity of 84.5%, which is higher than that of commercial chitin (82.1%). Observation of the chitin surface confirmed increased porosity and the removal of minerals and proteins. Mineral removal achieved over 99.9% removal efficiency at 3 min, 100℃, and 1,600 W. The optimal conditions for protein removal in chitin extraction from shrimp shells are 40℃ and 1,600 W. The extracted chitin has an α-chitin structure with a crystallinity of 84.5%. Thus, microwave heating can be used as an effective pretreatment method for mineral and protein removal in chitin extraction from crustaceans.
- 1 February 2025
- Published by Korean Society of Environmental Engineering in Journal of Korean Society of Environmental Engineers
- Vol. 47 (2) , 98-109
Open AccessExtraction of Chitin from Shrimp Shells using Microwave: Optimization of Protein Removal based on Central Composite Face-centered Design
The objective of this study is to extract chitin from shrimp shells by removing minerals and proteins using a microwave heating method. The optimal conditions for protein removal were proposed using response surface analysis. Experiments on mineral removal were conducted under discontinuous conditions with irradiation time (1~5 min), temperature (90~130℃), and irradiation power (400~1,600 W). Following the mineral removal process, protein removal experiments were performed under discontinuous conditions with irradiation time (1~10 min), temperature (40~100℃), and irradiation power (400~1,600 W). To identify the optimal points and interactions between factors for protein removal on a continuous scale, the central composite face-centered design, a type of response surface analysis, was employed. Independent variables were set as temperature (40~100℃) and irradiation power (600~1,600 W). Under discontinuous conditions, mineral removal experiments resulted in over 99.9% mineral removal efficiency at 3 min, 100℃, and 1,600 W. For protein removal, maximum efficiency of 94.9% was observed at 3 min, 40℃, and 1,600 W. Lower temperatures resulted in higher protein removal efficiency. Higher irradiation power led to increased protein removal efficiency. The optimal conditions for protein removal in continuous scale experiments were found to be 40℃ and 1,600 W. Under these conditions, a removal efficiency of 95% was achieved. All independent variables significantly influenced the removal process using microwave heating, with p<0.05. The chitin extracted in this experiment exhibited an α-chitin structure with a crystallinity of 84.5%, which is higher than that of commercial chitin (82.1%). Observation of the chitin surface confirmed increased porosity and the removal of minerals and proteins. Mineral removal achieved over 99.9% removal efficiency at 3 min, 100℃, and 1,600 W. The optimal conditions for protein removal in chitin extraction from shrimp shells are 40℃ and 1,600 W. The extracted chitin has an α-chitin structure with a crystallinity of 84.5%. Thus, microwave heating can be used as an effective pretreatment method for mineral and protein removal in chitin extraction from crustaceans.
- Open Access
- 1 December 2024
- Published by Korean Society of Environmental Engineering in Journal of Korean Society of Environmental Engineers
- Vol. 46 (12) , 775-782
Chemical Precipitation removal of Boron in Synthetic Wastewater using Microwave Heating
Objectives : The objective of this study is to investigate the potential for the removal of boron(B) from synthetic wastewater through chemical precipitation using microwave heating to identify the optimal conditions for the removal of boron.Methods : Synthetic wastewater was prepared using boric acid(H3BO3) and distilled water. The range of variables that exert an influence on boron removal included the initial pH 3-13, the calcium hydroxide(Ca(OH)2) dosage of 0.5-10 g per 30 mL(17–333 g/L), and the boron concentration of 100-1,500 mg/L. A face-centered design in response surface method was employed to identify the optimal conditions for boron removal in a continuous scale and to ascertain the interaction of the factors.Results and Discussion : In discontinuous conditions, the maximum removal efficiency was observed at initial pH 3, Ca(OH)2 of 2 g, and the boron concentration of 1,500 mg/L. As the pH value decreased, the removal of boron increased. The greatest removal efficiency was observed when the dosage of Ca(OH)2 was 2-5 g. It was also found that the higher the concentration of boron, the greater the removal efficiency. In the continuous scale, the optimal conditions for boron removal were identified as initial pH 3.3, the dosage of 6.2 g Ca(OH)2, and the boron concentration of 1,500 mg/L, with the removal efficiency of 93%. All independent variables exerted a statistically significant influence on chemical precipitation removal(p<0.05). In comparison to pH(p=0.047), boron concentration(p<0.001) and Ca(OH)2 dosage(p<0.001) demonstrated a more pronounced impact on boron removal. The interaction between boron concentration and Ca(OH)2 dosage was also identified as statistically significant(p<0.001).Conclusion : Chemical precipitation using microwave heating was effective in removal of boron from wastewater, and the optimal conditions in continuous scale through response surface analysis were initial pH 3.3, boron concentration 1,500 mg/L, and Ca(OH)2 dosage 6.2 g(207 g/L).
- 1 December 2024
- Published by Korean Society of Environmental Engineering in Journal of Korean Society of Environmental Engineers
- Vol. 46 (12) , 775-782
Open AccessChemical Precipitation removal of Boron in Synthetic Wastewater using Microwave Heating
Objectives : The objective of this study is to investigate the potential for the removal of boron(B) from synthetic wastewater through chemical precipitation using microwave heating to identify the optimal conditions for the removal of boron.Methods : Synthetic wastewater was prepared using boric acid(H3BO3) and distilled water. The range of variables that exert an influence on boron removal included the initial pH 3-13, the calcium hydroxide(Ca(OH)2) dosage of 0.5-10 g per 30 mL(17–333 g/L), and the boron concentration of 100-1,500 mg/L. A face-centered design in response surface method was employed to identify the optimal conditions for boron removal in a continuous scale and to ascertain the interaction of the factors.Results and Discussion : In discontinuous conditions, the maximum removal efficiency was observed at initial pH 3, Ca(OH)2 of 2 g, and the boron concentration of 1,500 mg/L. As the pH value decreased, the removal of boron increased. The greatest removal efficiency was observed when the dosage of Ca(OH)2 was 2-5 g. It was also found that the higher the concentration of boron, the greater the removal efficiency. In the continuous scale, the optimal conditions for boron removal were identified as initial pH 3.3, the dosage of 6.2 g Ca(OH)2, and the boron concentration of 1,500 mg/L, with the removal efficiency of 93%. All independent variables exerted a statistically significant influence on chemical precipitation removal(p<0.05). In comparison to pH(p=0.047), boron concentration(p<0.001) and Ca(OH)2 dosage(p<0.001) demonstrated a more pronounced impact on boron removal. The interaction between boron concentration and Ca(OH)2 dosage was also identified as statistically significant(p<0.001).Conclusion : Chemical precipitation using microwave heating was effective in removal of boron from wastewater, and the optimal conditions in continuous scale through response surface analysis were initial pH 3.3, boron concentration 1,500 mg/L, and Ca(OH)2 dosage 6.2 g(207 g/L).
- 7 February 2024
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 99 (4) , 893-901
Effect of iron powder on hydrogen sulfide reduction and phosphate removal in semi‐continuous anaerobic digestion treating primary sludge
BACKGROUND: To our best knowledge, no experimental study has previously investigated the simultaneous effects of adding Fe powder for the decrease of hydrogen sulfide (H2S) in biogas and the removal of phosphate (PO4‐P) in continuous anaerobic digestion (AD). This study investigated the effects of iron (Fe) powder (5 g L−1) in AD to remove H2S and PO4‐P. A comparative experiment was conducted using two semi‐continuous‐flow anaerobic digesters treating primary sludge at decreasing hydraulic retention times (HRTs) of 20 to 10 days.RESULTS: The addition of Fe powder to AD removed > 98% of H2S at all HRTs, and removed 64–72% of PO4‐P, with the highest removal efficiency at HRT = 10 d. The addition of Fe powder to AD had no noticeable effect on biogas production or pH, but it increased the CH4 content (62.7–66.0% in Fe‐treated vs 58.2–60.4% in the Control) partly due to the greater presence of Methanoregulaceae. The relative abundance of the microbial groups was more affected by HRT than by the addition of Fe powder. The presence of Fe powder notably increased the abundance of Spirochaetaceae and Syntrophaceae.CONCLUSION: As shown, the addition of Fe powder can improve the management of both H2S in the biogas and PO4‐P in the digested sludge in the AD system. © 2024 Society of Chemical Industry (SCI).
- 7 February 2024
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 99 (4) , 893-901
Effect of iron powder on hydrogen sulfide reduction and phosphate removal in semi‐continuous anaerobic digestion treating primary sludge
BACKGROUND: To our best knowledge, no experimental study has previously investigated the simultaneous effects of adding Fe powder for the decrease of hydrogen sulfide (H2S) in biogas and the removal of phosphate (PO4‐P) in continuous anaerobic digestion (AD). This study investigated the effects of iron (Fe) powder (5 g L−1) in AD to remove H2S and PO4‐P. A comparative experiment was conducted using two semi‐continuous‐flow anaerobic digesters treating primary sludge at decreasing hydraulic retention times (HRTs) of 20 to 10 days.RESULTS: The addition of Fe powder to AD removed > 98% of H2S at all HRTs, and removed 64–72% of PO4‐P, with the highest removal efficiency at HRT = 10 d. The addition of Fe powder to AD had no noticeable effect on biogas production or pH, but it increased the CH4 content (62.7–66.0% in Fe‐treated vs 58.2–60.4% in the Control) partly due to the greater presence of Methanoregulaceae. The relative abundance of the microbial groups was more affected by HRT than by the addition of Fe powder. The presence of Fe powder notably increased the abundance of Spirochaetaceae and Syntrophaceae.CONCLUSION: As shown, the addition of Fe powder can improve the management of both H2S in the biogas and PO4‐P in the digested sludge in the AD system. © 2024 Society of Chemical Industry (SCI).