Xiaoyong Ren
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Xiaoyong Ren has a total of 106 co-authors. Here are the top co-authors by number of shared publications:
- Zhiliang Zhang
Nanjing University of Aeronautics and Astronautics
54 shared publications - Qianhong Chen
Nanjing University of Aeronautics and Astronautics
41 shared publications Qianhong Chen
College of Automation Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, China
10 shared publications- Haoran Li
School of Electrical Engineering and Automation, Anhui University, Hefei, China
9 shared publications - Yu Wu
Aero-Power Sci-tech Center, Nanjing University of Aeronautics and Astronautics, Nanjing, China
7 shared publications - Shengdong Wang
Aero-Power Sci-tech Center, Nanjing University of Aeronautics and Astronautics, Nanjing, China
6 shared publications
Latest Publications
- 1 December 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (12) , 20933-20942
Phase-Compensated Wide-Bandwidth Current Sensor Combining Rogowski Coil and TMR
- 1 December 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (12) , 20933-20942
Phase-Compensated Wide-Bandwidth Current Sensor Combining Rogowski Coil and TMR
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73  (9) , 1-13
A High Efficiency Asymmetric Three-Level Buck–Boost Converter for Battery Charging Applications
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73  (9) , 1-13
A High Efficiency Asymmetric Three-Level Buck–Boost Converter for Battery Charging Applications
- 18 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 14  (3) , 2966-2978
Zero-Pole Configuration Method for Low-Voltage Stress Single-Switch Resonant Converter With Double-Sided Compensation
To address the high voltage stress issue in conventional isolated single-switch resonant converters (SSRCs), this paper proposes a novel zero-pole configuration method for general double-sided compensated SSRCs to reduce voltage stress. Input impedance analysis is performed, revealing that doublesided compensated SSRCs inherently exhibit one zero and two poles, thus possessing the inherent capability to achieve low voltage stress. By configuring the zero at the 2nd harmonic frequency and one pole around the 3rd harmonic frequency, lowvoltage stress can be realized. In addition, the study finds that a 3:1 ratio of the transformer’s magnetizing inductance to leakage inductance enables the zero to be placed at the 2nd harmonic frequency. The proposed zero-pole configuration method eliminates the need for additional LC resonant tanks, enabling low-voltage stress to be independent of the secondary compensation network type. Finally, a 1900W, 50kHz prototype with secondary-side LCC compensation network was built to verify the theoretical analysis. Experimental results demonstrate that the switch’s peak voltage is reduced to 2.16 times the input voltage, with a full-load efficiency of 93.85%.
- 18 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 14  (3) , 2966-2978
Zero-Pole Configuration Method for Low-Voltage Stress Single-Switch Resonant Converter With Double-Sided Compensation
To address the high voltage stress issue in conventional isolated single-switch resonant converters (SSRCs), this paper proposes a novel zero-pole configuration method for general double-sided compensated SSRCs to reduce voltage stress. Input impedance analysis is performed, revealing that doublesided compensated SSRCs inherently exhibit one zero and two poles, thus possessing the inherent capability to achieve low voltage stress. By configuring the zero at the 2nd harmonic frequency and one pole around the 3rd harmonic frequency, lowvoltage stress can be realized. In addition, the study finds that a 3:1 ratio of the transformer’s magnetizing inductance to leakage inductance enables the zero to be placed at the 2nd harmonic frequency. The proposed zero-pole configuration method eliminates the need for additional LC resonant tanks, enabling low-voltage stress to be independent of the secondary compensation network type. Finally, a 1900W, 50kHz prototype with secondary-side LCC compensation network was built to verify the theoretical analysis. Experimental results demonstrate that the switch’s peak voltage is reduced to 2.16 times the input voltage, with a full-load efficiency of 93.85%.
- 29 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72  (12) , 12888-12899
Modeling and Suppression Method of the Floating Potential in Inductive Power Transfer Systems for Monorail
In inductive power transfer (IPT) systems, the high-frequency voltage variations in coupling coils can induce an undesired floating potential on ungrounded surfaces, posing a safety risk. Considering the long rail-type coil structure, circuits on transmitting (Tx) and receiving (Rx) sides, an equivalent model of displacement current paths is proposed for predicting the floating potential on sorting transfer vehicles in monorail IPT systems. An expression for floating potential is then derived, revealing that the placement of compensation components for Tx coil is the main factor affecting the floating potential. Based on it, we propose the novel suppression approaches through symmetrical split resonant inductors and strategic repositioning of the Tx coil compensation elements. Experimental validation is conducted using 1-kW power pick-ups with a 3-m-long Tx coil. Experimental and simulation results confirm the validity of the analysis. Adopting the proposed method, remarkable floating potential suppression is achieved from 50.2 V to a near-zero level.
- 29 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72  (12) , 12888-12899
Modeling and Suppression Method of the Floating Potential in Inductive Power Transfer Systems for Monorail
In inductive power transfer (IPT) systems, the high-frequency voltage variations in coupling coils can induce an undesired floating potential on ungrounded surfaces, posing a safety risk. Considering the long rail-type coil structure, circuits on transmitting (Tx) and receiving (Rx) sides, an equivalent model of displacement current paths is proposed for predicting the floating potential on sorting transfer vehicles in monorail IPT systems. An expression for floating potential is then derived, revealing that the placement of compensation components for Tx coil is the main factor affecting the floating potential. Based on it, we propose the novel suppression approaches through symmetrical split resonant inductors and strategic repositioning of the Tx coil compensation elements. Experimental validation is conducted using 1-kW power pick-ups with a 3-m-long Tx coil. Experimental and simulation results confirm the validity of the analysis. Adopting the proposed method, remarkable floating potential suppression is achieved from 50.2 V to a near-zero level.
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13  (5) , 6281-6291
Three-Level T-Type APF With Paralleled Discrete SiC MOSFETs Using Optimized-Balanced Parasitic Inductance Structure
The implementation of a 100 kVA high-power-density Active Power Filter (APF) with constraints of volume, loss and cost faces the challenges of selecting optimal three-level topology and SiC MOSFET, reducing Turn-off Transient voltage Overshoot (TTVO) and balancing Turn-on Transient Current Sharing (TTCS). This paper presents an optimal solution design methodology for topologies and devices selection, and proposes a parasitic inductance minimized-and-balanced PCB improve method for reducing TTVO and balancing TTCS. The three-level T-type (3LT2) and neutral-point-clamped (NPC) topologies with the finitely enumerated SiC devices are quantitatively evaluated to select the optimal solution satisfying constraints of volume, loss and cost. The 3LT2 circuit with three parallel 1200V discrete devices is evaluated as the optimal solution that faces the TTVO and TTCS problems in practice. A minimized-and-balanced parasitic inductance PCB structure is proposed to solve the challenges. The TTVO is reduced from 1.06 kV to 780 V, a reduction of 26.4 %, and the TTCS deviation from 82.4 % to 3.7 % under an 800 V DC voltage and a 450 A load current. The APF prototype achieves a power density of 4.27 kW/L and a full-load efficiency of 98.16 % with reducing power device cost by 10.4 %.
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13  (5) , 6281-6291
Three-Level T-Type APF With Paralleled Discrete SiC MOSFETs Using Optimized-Balanced Parasitic Inductance Structure
The implementation of a 100 kVA high-power-density Active Power Filter (APF) with constraints of volume, loss and cost faces the challenges of selecting optimal three-level topology and SiC MOSFET, reducing Turn-off Transient voltage Overshoot (TTVO) and balancing Turn-on Transient Current Sharing (TTCS). This paper presents an optimal solution design methodology for topologies and devices selection, and proposes a parasitic inductance minimized-and-balanced PCB improve method for reducing TTVO and balancing TTCS. The three-level T-type (3LT2) and neutral-point-clamped (NPC) topologies with the finitely enumerated SiC devices are quantitatively evaluated to select the optimal solution satisfying constraints of volume, loss and cost. The 3LT2 circuit with three parallel 1200V discrete devices is evaluated as the optimal solution that faces the TTVO and TTCS problems in practice. A minimized-and-balanced parasitic inductance PCB structure is proposed to solve the challenges. The TTVO is reduced from 1.06 kV to 780 V, a reduction of 26.4 %, and the TTCS deviation from 82.4 % to 3.7 % under an 800 V DC voltage and a 450 A load current. The APF prototype achieves a power density of 4.27 kW/L and a full-load efficiency of 98.16 % with reducing power device cost by 10.4 %.
- 6 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13  (2) , 2036-2045
Analytical Modeling and Worst Case Analysis of Common-Mode EMI Spectrum in Quasi-Resonant Flyback Converters
Modern quasi-resonant (QR) Flyback converter employs advanced control strategies to optimize efficiency across all load conditions, resulting in a complex electromagnetic interference (EMI) spectrum. This paper proposes an analytical modeling method to facilitate the prediction and suppression of the common-mode (CM) EMI noise of QR Flyback converter. By incorporating practical considerations such as the second-harmonic ripple on the input, valley-switching techniques, and varying load conditions, an accurate CM EMI (CE) model for QR Flyback converters is developed, serving as a predictive tool for CM noise. Furthermore, a worst-case analysis (WCA) is carried out, which establishes the design criteria for the CM filter. The proposed noise-prediction method is validated by experiments on a 90W QR Flyback charger, demonstrating an exceptionally low prediction error of less than 3dB under different input and output conditions. Additionally, a CM filter is designed according to the WCA-based guidelines, which shows effective suppression of CM noise, yielding satisfactory results by achieving compliance with EN55032 Class B standards across the entire test frequency range.
- 6 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13  (2) , 2036-2045
Analytical Modeling and Worst Case Analysis of Common-Mode EMI Spectrum in Quasi-Resonant Flyback Converters
Modern quasi-resonant (QR) Flyback converter employs advanced control strategies to optimize efficiency across all load conditions, resulting in a complex electromagnetic interference (EMI) spectrum. This paper proposes an analytical modeling method to facilitate the prediction and suppression of the common-mode (CM) EMI noise of QR Flyback converter. By incorporating practical considerations such as the second-harmonic ripple on the input, valley-switching techniques, and varying load conditions, an accurate CM EMI (CE) model for QR Flyback converters is developed, serving as a predictive tool for CM noise. Furthermore, a worst-case analysis (WCA) is carried out, which establishes the design criteria for the CM filter. The proposed noise-prediction method is validated by experiments on a 90W QR Flyback charger, demonstrating an exceptionally low prediction error of less than 3dB under different input and output conditions. Additionally, a CM filter is designed according to the WCA-based guidelines, which shows effective suppression of CM noise, yielding satisfactory results by achieving compliance with EN55032 Class B standards across the entire test frequency range.