Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Juan Pablo Hurtado-Cruz has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Predictive Model for Water Consumption in a Copper Mineral Concentrator Plant Located in a Desert Area Using Machine Learning

    by Sebastián A. Pérez Cortés, Eduardo H. Contreras Moreno, Humberto Flores Páez, Juan P. Hurtado Cruz, Juan A. Jarufe Troncoso

    In this study, water consumption predictions are made based on data obtained from two copper mineral concentration plants located in the northern region of Chile, Antofagasta Region, measured during a year of mining operation. The area to which this operation belongs is characterized by a desert climate with average annual rainfall of less than 50 mm and maximum and minimum temperatures of 29 °C and 4 °C for summer, and 26 °C and −5 °C for winter, measured during 2022. To perform the predictions, a database corresponding to two concentration plants with daily measurements for a year was used, which were analyzed using four regression models using Machine Learning (ML) in Python: Support Vector Regressor (SVR), Extreme Gradient Boost (XGBoost), Artificial Neural Network (ANN), and Random Forest Regressor (RF). The predictions obtained by each of the ML models were studied using cross-validation hyperparameter tuning and identifying the variable with the greatest impact. The model with the best prediction results was ANN, as it yielded the lowest relative error in the predictions.


  • Ventilation Modeling of Cavern with CFD

    by Juan Pablo Hurtado-Cruz, Marcelo Antonio Carvajal-Meza, Sebastián Alexander Pérez-Cortés, Juan Andrés Jarufe-Troncoso, Juan Pablo Vargas-Norambuena


  • Geothermal Energy Storage: A Conceptual Assessment of Geologic Thermal Storage Systems in North Dakota

    by E. Gyimah, M. Metwally, O. S. Tomomewo, J. P. Hurtado, M. Alamooti, W. Gosnold

    Geothermal energy and Aquifer thermal energy storage can provide beneficial ways of storing energy in excess and providing energy when needed. North Dakota's renewable energy system is impacted by its harsh winters. Geologic aquifer thermal aquifer storage system is a large scale geothermal system that can act as energy storage media. Aquifer thermal storage systems are dependent on heat conductivity of rocks, storage capacity of aquifer, fluid flow, geochemistry and geo-mechanics. The goals of the project are to 1) evaluate the amount of energy that can be stored in deep aquifers; 2) access the amount of energy that is thermally recoverable; 3) monitor changes in geo-mechanical parameters. CMG STARS, a three-phase multi-component thermal and steam additive simulator, was used for the thermal numerical simulation which takes into account the geo-mechanics (thermal dilation and re-compaction). A conventional reservoir with representative porosity and permeability is modelled in CMG and Semi Analytical Model (SAM) was used to calculate the wellbore dynamics involved with geothermal operations. This is used to calculate heat transfer to the surrounding formation and determine our heat loss. Our preliminary results show us the reservoir pore volume dilation re-compaction model changes from cold water injection. The grid block void porosity dilation re-compaction model changes are greatly influenced by grid block pressure. INTRODUCTION: Geothermal Energy and Aquifer Thermal Energy Storage (ATES): Geothermal energy refers to the earth's thermal energy that can be converted into electrical energy. Emissions from the geothermal energy industry are substantially low, which is an excellent asset to reaching a low-carbon economy. Hot dry rocks and hydrothermal resources are the primary geothermal energy sources. Water from surface seeps through faults and cracks of earth and is warmed by hot rocks or water is trapped by impermeable layers to create geothermal reservoirs. Sedimentary basins have great geologic and reservoir properties for low-cost energy generation for geothermal energy. Hot water moves from deep sources to shallow reservoirs for hot water geothermal reservoirs. Hydrothermal systems use steam or water for electricity generation. Enhanced geothermal systems extract thermal energy from geothermal resources with lower permeability and fluid saturation. (Grant & Bixley, 2011)(Barbier, 2002)


  • Open Access

    Achieving Circularity through Novel Product-Service Systems in the Mining Industry: An Opportunity for Circularity

    by Juan Pablo Vargas, Angélica Patricia Muñoz Lagos, José Guillermo Feriz Torres, Ian Scott Kinney, Sebastián Pérez Cortés, Juan Pablo Hurtado

    The evolution toward sustainable mining can be achieved by implementing circular economies (CEs), and one way forward is via product-service systems (PSSs). However, applying PSSs in the mining industry is an area with little extant research. We seek to contribute to CE and sustainability research by proposing a model by which mining companies can achieve circularity through their suppliers: something which has not yet been explored. First, we present a critical literature review of published papers about the barriers and benefits in industries where servitization or PSS has been applied. We discuss barriers impeding PSS implementation in the mining industry, along with related concepts including CE and PSSs in digital technologies. With this study we hope to draw more discussion to the topic of PSSs in the mining industry and provide useful guidelines to academics and industry professionals for PSS implementation in mining: an important step toward circularity.


  • Open Access

    A Computational Fluid Dynamic Study of Developed Parallel Stations for Primary Fans

    by Juan Pablo Hurtado, Gabriel Reyes, Juan Pablo Vargas, Enrique Acuña

    A Computational fluid dynamic (CFD) model was developed considering three geometries for primary parallel fan stations that have already been developed, implemented, and are currently in operation within Chilean mines. To standardize the comparison, the same primary fan was used in all the simulations with a unique set of settings (speed, blade angle, and density). The CFD representation was used to determine the operating point per configuration and compare the performances in terms of airflow and pressure delivered. This approach allowed ranking primary fan station geometry based on resistance curve and energy consumption of the fan. This paper presents the results obtained through the CFD simulations and the corresponding primary fans operating points of each configuration: symmetrical branches (SB), overlap branches (OB), and run around (RA) bypass. The RA configuration was identified as the best-performing station geometry on the lowest frictional and shock pressure losses, highest airflow delivery, and lowest energy cost. The results are discussed, considering pressure, velocity, and vector contours to understand the fluid dynamics phenomena occurring inside the station. The capital cost involved in the development of each primary parallel station was considered in the analysis in addition to the energy cost to determine the economic configuration over time.


  • Open Access

    Optimization Study of Guide Vanes for the Intake Fan-Duct Connection Using CFD

    by Juan Pablo Hurtado, Bryan Villegas, Sebastián Pérez, Enrique Acuña

    The connection between an intake fan and a ventilation shaft must be designed in such a way that it minimizes the energy waste due to singularity losses. As a result, the questions of which radius of curvature to use and if guide vanes have to be included need to be answered. In that case, the variables such as the number, upstream and downstream penetration length, radius of curvature, and width of the vanes, need to be defined. Although this work is oriented to mine ventilation, these questions are usually valid in other engineering applications as well. The objective of this study is to define the previously mentioned variables to determine the optimal design combination for the radius/diameter relationship (r/D). Computational fluid dynamics was used to determine the shock loss factor of seven elbow curvature ratios for a 3 m diameter duct and fan, with and without guide vanes to estimate the best performing configuration and, therefore, to maximize the fan airflow volume. The methodology used consisted of initially developing models in 2D geometries, to optimize the meshing and the CPU use, and studying separately the number of vanes, upstream and downstream penetration, radius of curvature, and width of the vanes for each curvature ratio (r/D). Then, the best-performing variable combinations for each curvature ratio were selected to be simulated and studied with the 3D geometries. The application of the guide vane designs for three-dimensional simulated geometries is presented, first without and then with guide vanes, including the shock loss factors obtained. The methodology and obtained results allowed quantifying the energy savings and to reduce the CFD simulations steps required to optimize the design of the elbow and guide vanes. The results obtained cannot be used with elbows in exhaust fans, because fluid dynamics phenomena are different.


  • Noise Prediction of a Centrifugal Fan: Numerical Results and Experimental Validation

    by Rafael Ballesteros-Tajadura, Sandra Velarde-Suárez, Juan Pablo Hurtado-Cruz

    Centrifugal fans are widely used in several applications, and in some cases, the noise generated by these machines has become a serious problem. The centrifugal fan noise is frequently dominated by tones at the blade passing frequency as a consequence of the strong interaction between the flow discharged from the impeller and the volute tongue. In this study, a previously published aeroacoustic prediction methodology (Cho, Y., and Moon, Y.J., 2003, “Discrete Noise Prediction of Variable Pitch Cross-Flow Fans by Unsteady Navier-Stokes Computations ,” ASME J. Fluids Eng., 125, pp. 543–550) has been extended to three-dimensional turbulent flow in order to predict the noise generated by a centrifugal fan. A three-dimensional numerical simulation of the complete unsteady flow on the whole impeller-volute configuration has been carried out using the computational fluid dynamics code FLUENT ® . The unsteady forces applied by the fan blades to the fluid are obtained from the data provided by the simulation. The Ffowcs Williams and Hawkings model extension of Lighthill’s analogy has been used to predict the aerodynamic noise generated by the centrifugal fan from these unsteady forces. Also, the noise generated by the fan has been measured experimentally, and the experimental results have been compared to the numerical results in order to validate the aerodynamic noise prediction methodology. Reasonable agreement has been found between the numerical and the experimental results.


  • Experimental determination of the tonal noise sources in a centrifugal fan

    by Sandra Velarde-Suárez, Rafael Ballesteros-Tajadura, Juan Pablo Hurtado-Cruz, Carlos Santolaria-Morros


  • A predictive maintenance procedure using pressure and acceleration signals from a centrifugal fan

    by Sandra Velarde-Suárez, Rafael Ballesteros-Tajadura, Juan Pablo Hurtado-Cruz


  • Numerical Calculation of Pressure Fluctuations in the Volute of a Centrifugal Fan

    by Rafael Ballesteros-Tajadura, Sandra Velarde-Suárez, Juan Pablo Hurtado-Cruz, Carlos Santolaria-Morros

    In this work, a numerical model has been applied in order to obtain the wall pressure fluctuations at the volute of an industrial centrifugal fan. The numerical results have been compared to experimental results obtained in the same machine. A three-dimensional numerical simulation of the complete unsteady flow on the whole impeller-volute configuration has been carried out using the computational fluid dynamics code FLUENT®. This code has been employed to calculate the time-dependent pressure both in the impeller and in the volute. In this way, the pressure fluctuations in some locations over the volute wall have been obtained. The power spectra of these fluctuations have been obtained, showing an important peak at the blade passing frequency. The amplitude of this peak presents the highest values near the volute tongue, but the spatial pattern over the volute extension is different depending on the operating conditions. A good agreement has been found between the numerical and the experimental results.