Qing-Ping Feng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qing-Ping Feng has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Gui-Wen Huang
State Key Laboratory of Cryogenic Science and Technology, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing, China
7 shared publications Na Li
Technical Institute of Physics and Chemistry , Chinese Academy of Sciences , No. 29 Zhongguancun East Road , Beijing 100190 , P. R. China
7 shared publications- Shao-Yun Fu
College of Aerospace Engineering
4 shared publications Hong-Mei Xiao
3 shared publicationsXing-Hua Wu
Technical Institute of Physics and Chemistry, Chinese Academy of Sciences , No. 29, Zhongguancun East Road, Beijing 100190, P. R. China
3 shared publicationsYi Du
Technical Institute of Physics and Chemistry, Chinese Academy of Sciences , No. 29, Zhongguancun East Road, Beijing 100190, P. R. China
3 shared publications
Latest Publications
- 4 April 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (16) , 15028-15037
Binder-Free Graphene/Silver Nanowire Gel-Like Composite with Tunable Properties and Multifunctional Applications
To realize macroscopically utilization of the excellent properties of graphene, various forms of graphene assemblies have been investigated. Among them, the gel form assemblies show great advantages because they are shapeable and self-healable, and their manufacturing processes are facile and simple. In the conventional gel formed graphene assemblies, a relatively large content of binders, including hydrophilic polymers, celluloses, or amorphous inorganic materials are mixed with the graphene to achieve the gelation. However, these binders are electrically nonconductive and electrochemically inactive. Thus, the favorable functionalities of the composite will be weakened, and the potential advantages of graphene cannot be fully utilized. Herein, a binder-free silver nanowire (Ag-NW)/reduced graphene oxide (rGO) gel-like composite is designed and successfully fabricated by using ultra-long Ag-NWs to enhance the hierarchical synergistic effects. The fabrication technique is highly efficient and repeatable, and the obtained composite is flexible, stretchable and self-healable. Furthermore, the overall properties of the composite can be easily adjusted in a wide range by controlling the mass ratio between Ag-NW and rGO, which makes it multipurpose and suitable in different applications. Several demonstrations have been carried out and some special performances including linear strain sensing range and rapid transformation from wet to dry state are found in this unique composite. This binder-free structure could also be expended to other material systems, which may offer a valuable inspire for the development of functional devices based on nanocomposite.
- 4 April 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (16) , 15028-15037
Binder-Free Graphene/Silver Nanowire Gel-Like Composite with Tunable Properties and Multifunctional Applications
To realize macroscopically utilization of the excellent properties of graphene, various forms of graphene assemblies have been investigated. Among them, the gel form assemblies show great advantages because they are shapeable and self-healable, and their manufacturing processes are facile and simple. In the conventional gel formed graphene assemblies, a relatively large content of binders, including hydrophilic polymers, celluloses, or amorphous inorganic materials are mixed with the graphene to achieve the gelation. However, these binders are electrically nonconductive and electrochemically inactive. Thus, the favorable functionalities of the composite will be weakened, and the potential advantages of graphene cannot be fully utilized. Herein, a binder-free silver nanowire (Ag-NW)/reduced graphene oxide (rGO) gel-like composite is designed and successfully fabricated by using ultra-long Ag-NWs to enhance the hierarchical synergistic effects. The fabrication technique is highly efficient and repeatable, and the obtained composite is flexible, stretchable and self-healable. Furthermore, the overall properties of the composite can be easily adjusted in a wide range by controlling the mass ratio between Ag-NW and rGO, which makes it multipurpose and suitable in different applications. Several demonstrations have been carried out and some special performances including linear strain sensing range and rapid transformation from wet to dry state are found in this unique composite. This binder-free structure could also be expended to other material systems, which may offer a valuable inspire for the development of functional devices based on nanocomposite.
- 25 May 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (22) , 19278
Correction to “Enhanced Microwave Absorption Performance of Coated Carbon Nanotubes by Optimizing the Fe3O4 Nanocoating Structure”
- 25 May 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (22) , 19278
Correction to “Enhanced Microwave Absorption Performance of Coated Carbon Nanotubes by Optimizing the Fe3O4 Nanocoating Structure”
- 26 December 2017
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (1) , 723-732
Laser-Printed In-Plane Micro-Supercapacitors: From Symmetric to Asymmetric Structure
Here we propose and demonstrate a complete solution for efficiently fabricating in-plane micro-supercapacitors (MSCs) from symmetric to asymmetric structure. By using an original laser printing process, symmetric MSC with reduced graphene oxide (rGO) / silver nanowires (Ag-NWs) hybrid electrodes was facilely fabricated and a high areal capacitance of 5.5 mF cm-2 was achieved, which reaches the best reports on graphene-based MSCs. More importantly, a “print-and-fold” method has been creatively proposed that enabled the rapidly manufacturing of asymmetric in-plane MSCs beyond the traditional cumbersome technologies. α-Ni(OH)2 particles with high tapping density was successfully synthesized and employed as the pseudocapacitive material. Consequently, an improved supply voltage of 1.5 V was obtained and an areal capacitance as high as 8.6 mF cm-2 has been realized. Moreover, a demonstration of a miniaturized MSC pack was performed by multiply folding the serially Ag-NW-connected MSC units. As a result, a compact MSC pack with high supply voltage of 3 V was obtained which can be utilized to power a LED light. These presented technologies may pave the way for the efficiently producing of high performance in-plane MSCs, meanwhile offer a solution for the achievement of practical power supply packs integrated in limited spaces.
- 26 December 2017
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (1) , 723-732
Laser-Printed In-Plane Micro-Supercapacitors: From Symmetric to Asymmetric Structure
Here we propose and demonstrate a complete solution for efficiently fabricating in-plane micro-supercapacitors (MSCs) from symmetric to asymmetric structure. By using an original laser printing process, symmetric MSC with reduced graphene oxide (rGO) / silver nanowires (Ag-NWs) hybrid electrodes was facilely fabricated and a high areal capacitance of 5.5 mF cm-2 was achieved, which reaches the best reports on graphene-based MSCs. More importantly, a “print-and-fold” method has been creatively proposed that enabled the rapidly manufacturing of asymmetric in-plane MSCs beyond the traditional cumbersome technologies. α-Ni(OH)2 particles with high tapping density was successfully synthesized and employed as the pseudocapacitive material. Consequently, an improved supply voltage of 1.5 V was obtained and an areal capacitance as high as 8.6 mF cm-2 has been realized. Moreover, a demonstration of a miniaturized MSC pack was performed by multiply folding the serially Ag-NW-connected MSC units. As a result, a compact MSC pack with high supply voltage of 3 V was obtained which can be utilized to power a LED light. These presented technologies may pave the way for the efficiently producing of high performance in-plane MSCs, meanwhile offer a solution for the achievement of practical power supply packs integrated in limited spaces.
- 14 December 2017
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 9 (51) , 44828-44838
A Novel Type of Battery–Supercapacitor Hybrid Device with Highly Switchable Dual Performances Based on a Carbon Skeleton/Mg2Ni Free-Standing Hydrogen Storage Electrode
The sharp proliferation of high power electronics and electrical vehicles has promoted growing demands for power sources with simultaneous performances of high energy and power densities. Under the circumstances, battery-supercapacitor hybrid devices are attracting considerable attention as they combine the advantages of both batteries and supercapacitors. Here, a novel type of hybrid device based on carbon skeleton / Mg2Ni free-standing electrode without the traditional nickel foam current collector is reported, which has been designed and fabricated through a dispersing-freeze drying method by employing the reduced graphene oxide (rGO) and multi-walled carbon nanotubes (MWCNTs) as hybrid skeleton. As a result, the Mg2Ni alloy is able to deliver a high discharge capacity of 644 mAh g-1 and more importantly, a high cycling stability with retention over 78% after 50 charge/discharge cycles has been achieved, which exceeds almost all the results ever reported on Mg2Ni alloy. Simultaneously, the electrode could also exhibit excellent supercapacitor performances including high specific capacities (296 F g-1) and outstanding cycling stability (100% retention after 100 cycles). Moreover, the hybrid device can switch between battery and supercapacitor modes immediately for need during application. These features make the C skeleton/alloy electrode a highly promising candidate for battery-supercapacitor hybrid devices with high power/energy density and favorable cycling stability.
- 14 December 2017
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 9 (51) , 44828-44838
A Novel Type of Battery–Supercapacitor Hybrid Device with Highly Switchable Dual Performances Based on a Carbon Skeleton/Mg2Ni Free-Standing Hydrogen Storage Electrode
The sharp proliferation of high power electronics and electrical vehicles has promoted growing demands for power sources with simultaneous performances of high energy and power densities. Under the circumstances, battery-supercapacitor hybrid devices are attracting considerable attention as they combine the advantages of both batteries and supercapacitors. Here, a novel type of hybrid device based on carbon skeleton / Mg2Ni free-standing electrode without the traditional nickel foam current collector is reported, which has been designed and fabricated through a dispersing-freeze drying method by employing the reduced graphene oxide (rGO) and multi-walled carbon nanotubes (MWCNTs) as hybrid skeleton. As a result, the Mg2Ni alloy is able to deliver a high discharge capacity of 644 mAh g-1 and more importantly, a high cycling stability with retention over 78% after 50 charge/discharge cycles has been achieved, which exceeds almost all the results ever reported on Mg2Ni alloy. Simultaneously, the electrode could also exhibit excellent supercapacitor performances including high specific capacities (296 F g-1) and outstanding cycling stability (100% retention after 100 cycles). Moreover, the hybrid device can switch between battery and supercapacitor modes immediately for need during application. These features make the C skeleton/alloy electrode a highly promising candidate for battery-supercapacitor hybrid devices with high power/energy density and favorable cycling stability.
- 15 August 2017
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 9 (34) , 28980-28989
Reduced Graphene Oxide Coating with Anticorrosion and Electrochemical Property-Enhancing Effects Applied in Hydrogen Storage System
Low-capacity retention is the most prominent problem of the magnesium nickel alloy (Mg2Ni), which prevents it from being commercially applied. Here, we propose a practical method for enhancing the cycle stability of the Mg2Ni alloy. Reduced graphene oxide (rGO) possesses a graphene-based structure, which could provide high-quality barriers that block the hydroxyl in the aqueous electrolyte; it also possesses good hydrophilicity. rGO has been successfully coated on the amorphous-structured Mg2Ni alloy via electrostatic assembly to form the rGO-encapsulated Mg2Ni alloy composite (rGO/Mg2Ni). The experimental results show that ζ potentials of rGO and the modified Mg2Ni alloy are totally opposite in water, with values of −11.0 and +22.4 mV, respectively. The crumpled structure of rGO sheets and the contents of the carbon element on the surface of the alloy are measured using scanning electron microscopy, transmission electron microscopy, and energy dispersive spectrometry. The Tafel polarization test indicates that the rGO/Mg2Ni system exhibits a much higher anticorrosion ability against the alkaline solution during charging/discharging. As a result, high-capacity retentions of 94% (557 mAh g–1) at the 10th cycle and 60% (358 mAh g–1) at the 50th cycle have been achieved, which are much higher than the results on Mg2Ni capacity retention combined with the absolute value reported so far to our knowledge. In addition, both the charge-transfer reaction rate and the hydrogen diffusion rate are proven to be boosted with the rGO encapsulation. Overall, this work demonstrates the effective anticorrosion and electrochemical property-enhancing effects of rGO coating and shows its applicability in the Mg-based hydrogen storage system.
- 15 August 2017
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 9 (34) , 28980-28989
Reduced Graphene Oxide Coating with Anticorrosion and Electrochemical Property-Enhancing Effects Applied in Hydrogen Storage System
Low-capacity retention is the most prominent problem of the magnesium nickel alloy (Mg2Ni), which prevents it from being commercially applied. Here, we propose a practical method for enhancing the cycle stability of the Mg2Ni alloy. Reduced graphene oxide (rGO) possesses a graphene-based structure, which could provide high-quality barriers that block the hydroxyl in the aqueous electrolyte; it also possesses good hydrophilicity. rGO has been successfully coated on the amorphous-structured Mg2Ni alloy via electrostatic assembly to form the rGO-encapsulated Mg2Ni alloy composite (rGO/Mg2Ni). The experimental results show that ζ potentials of rGO and the modified Mg2Ni alloy are totally opposite in water, with values of −11.0 and +22.4 mV, respectively. The crumpled structure of rGO sheets and the contents of the carbon element on the surface of the alloy are measured using scanning electron microscopy, transmission electron microscopy, and energy dispersive spectrometry. The Tafel polarization test indicates that the rGO/Mg2Ni system exhibits a much higher anticorrosion ability against the alkaline solution during charging/discharging. As a result, high-capacity retentions of 94% (557 mAh g–1) at the 10th cycle and 60% (358 mAh g–1) at the 50th cycle have been achieved, which are much higher than the results on Mg2Ni capacity retention combined with the absolute value reported so far to our knowledge. In addition, both the charge-transfer reaction rate and the hydrogen diffusion rate are proven to be boosted with the rGO encapsulation. Overall, this work demonstrates the effective anticorrosion and electrochemical property-enhancing effects of rGO coating and shows its applicability in the Mg-based hydrogen storage system.
- 6 June 2017
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 9 (27) , 9598-9605
A paper-based touch sensor with an embedded micro-probe array fabricated by double-sided laser printing
Touch sensor is one of the key components for human interfacing devices. However, although various touch sensors have been demonstrated, their sophisticated fabrication processes and complicated structures make them expensive and delicate, and thus they are not considered to be practical for wide application in daily life. Herein, we present a low-cost and scalable paper-based touch sensor suitable for practical applications. The sensor is based on the novel structure of embedded silver nanowire micro-probe arrays in a paper substrate, which exhibits high sensitivity to multiple touch inputs and compact structure with a total thickness of ca. 100 μm. Silver nanowire electrodes on two sides are manufactured at the same time via an original double-sided laser printing technique. Since this technique is mask-free, solvent-free and highly efficient, it is very suitable for paper substrates that cannot endure solvent processing. The sensing properties of the sensor in various extreme situations are examined and the spatial distributions of touch pressure are detected by arranging the sensing units in arrays. Demonstration examples of the touch sensor and pressure mapping are presented, and finally, the successful application of the sensor array in an electronic lock system is shown to further illustrate its applicability.
- 6 June 2017
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 9 (27) , 9598-9605
A paper-based touch sensor with an embedded micro-probe array fabricated by double-sided laser printing
Touch sensor is one of the key components for human interfacing devices. However, although various touch sensors have been demonstrated, their sophisticated fabrication processes and complicated structures make them expensive and delicate, and thus they are not considered to be practical for wide application in daily life. Herein, we present a low-cost and scalable paper-based touch sensor suitable for practical applications. The sensor is based on the novel structure of embedded silver nanowire micro-probe arrays in a paper substrate, which exhibits high sensitivity to multiple touch inputs and compact structure with a total thickness of ca. 100 μm. Silver nanowire electrodes on two sides are manufactured at the same time via an original double-sided laser printing technique. Since this technique is mask-free, solvent-free and highly efficient, it is very suitable for paper substrates that cannot endure solvent processing. The sensing properties of the sensor in various extreme situations are examined and the spatial distributions of touch pressure are detected by arranging the sensing units in arrays. Demonstration examples of the touch sensor and pressure mapping are presented, and finally, the successful application of the sensor array in an electronic lock system is shown to further illustrate its applicability.