Tao Jiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tao Jiang has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Jin-Guang Teng
Department of Civil and Environmental Engineering, The Hong Kong Polytechnic University, Hong Kong, China
5 shared publications C. J. Lin
Formerly, Postgraduate Student, School of Civil and Transportation Engineering, Guangdong Univ. of Technology, Guangzhou 510006, China
2 shared publications- En Li Xie
Zhejiang Shuren University
2 shared publications G. M. Chen
Professor, School of Civil and Transportation Engineering, Guangdong Univ. of Technology, Guangzhou 510006, China
2 shared publicationsJ. J. Zhang
Formerly, Postgraduate Student, School of Civil and Transportation Engineering, Guangdong Univ. of Technology, Guangzhou 510006, China
2 shared publicationsT Yu
Department of Civil and Environmental Engineering, The Hong Kong Polytechnic University, Hong Kong, China
2 shared publications
Latest Publications
- 15 September 2025
- Published by SAGE Publications in Advances in Structural Engineering
- Vol. 29  (7) , 1417-1436
Investigation of in-plane stability in bending-active arches
Bending-active arches derive their curved shape from the elastic bending of an initially straight strut, a process that necessitates slender and flexible members. Recent interest in this structural form has been propelled by the adoption of fiber-reinforced polymer profiles, while stability remains a critical concern for bending-active arches. In this study, the in-plane instability of bending-active arches is investigated under both hinged and fixed support conditions, with mid-span concentrated loads and uniformly distributed loads considered. Analytical formulations capturing symmetric and antisymmetric instability modes are derived and validated against numerical simulations performed in Abaqus. A parametric study is then conducted to identify the roles of span ratio and loading configurations. Results indicate that symmetric instability generally exhibits a higher peak load than antisymmetric instability under the same span ratio, although antisymmetric instability often develops earlier—an exception arises at certain span ratios for arches with fixed supports. Under uniformly distributed loads, arches with larger span ratios may initially experience a negative (upward) mid-span deflection. Furthermore, half-span uniform loading consistently achieves higher peak loads than full-span uniform loading. In hinged arches subjected to mid-span concentrated loads, looping load–deflection behavior emerges, with smaller span ratios yielding higher peak loads.
- 15 September 2025
- Published by SAGE Publications in Advances in Structural Engineering
- Vol. 29  (7) , 1417-1436
Investigation of in-plane stability in bending-active arches
Bending-active arches derive their curved shape from the elastic bending of an initially straight strut, a process that necessitates slender and flexible members. Recent interest in this structural form has been propelled by the adoption of fiber-reinforced polymer profiles, while stability remains a critical concern for bending-active arches. In this study, the in-plane instability of bending-active arches is investigated under both hinged and fixed support conditions, with mid-span concentrated loads and uniformly distributed loads considered. Analytical formulations capturing symmetric and antisymmetric instability modes are derived and validated against numerical simulations performed in Abaqus. A parametric study is then conducted to identify the roles of span ratio and loading configurations. Results indicate that symmetric instability generally exhibits a higher peak load than antisymmetric instability under the same span ratio, although antisymmetric instability often develops earlier—an exception arises at certain span ratios for arches with fixed supports. Under uniformly distributed loads, arches with larger span ratios may initially experience a negative (upward) mid-span deflection. Furthermore, half-span uniform loading consistently achieves higher peak loads than full-span uniform loading. In hinged arches subjected to mid-span concentrated loads, looping load–deflection behavior emerges, with smaller span ratios yielding higher peak loads.
- 22 June 2024
- Published by SAGE Publications in Advances in Structural Engineering
- Vol. 27  (12) , 2153-2166
Enhanced deflection method for large-curvature problems: Formulation, verification and application to fiber-reinforced polymer-enabled arches
Motivated by a curiosity to explore the behavior of innovative arch structures enabled by the use of fiber-reinforced polymer (FRP) composites, this paper proposes a theoretical model built upon an enhanced formulation of the deflection method, broadening its scope to large-curvature problems. Traditionally, the deflection method approximates curvature as the second-order derivative of deflection, a simplification valid only for small curvatures. This limitation poses a challenge when applying the deflection method to problems involving large curvatures, a characteristic inherent in FRP-enabled arches where significant curvatures arise either initially or due to deformation. The enhanced formulation at the core of the proposed model addresses this challenge by incorporating a circular deflection function. This function posits that each deformed segment of the structural member can be represented by a circular arc, with its curvature and length related to the internal axial force and bending moment at the midpoint section of the segment. This feature facilitates the exact representation of curvature, offering the proposed model a unified approach capable of addressing both small- and large-curvature problems. The paper details the formulation and verification of the theoretical model, with an emphasis on its application to representative cases of FRP-enabled arches.
- 22 June 2024
- Published by SAGE Publications in Advances in Structural Engineering
- Vol. 27  (12) , 2153-2166
Enhanced deflection method for large-curvature problems: Formulation, verification and application to fiber-reinforced polymer-enabled arches
Motivated by a curiosity to explore the behavior of innovative arch structures enabled by the use of fiber-reinforced polymer (FRP) composites, this paper proposes a theoretical model built upon an enhanced formulation of the deflection method, broadening its scope to large-curvature problems. Traditionally, the deflection method approximates curvature as the second-order derivative of deflection, a simplification valid only for small curvatures. This limitation poses a challenge when applying the deflection method to problems involving large curvatures, a characteristic inherent in FRP-enabled arches where significant curvatures arise either initially or due to deformation. The enhanced formulation at the core of the proposed model addresses this challenge by incorporating a circular deflection function. This function posits that each deformed segment of the structural member can be represented by a circular arc, with its curvature and length related to the internal axial force and bending moment at the midpoint section of the segment. This feature facilitates the exact representation of curvature, offering the proposed model a unified approach capable of addressing both small- and large-curvature problems. The paper details the formulation and verification of the theoretical model, with an emphasis on its application to representative cases of FRP-enabled arches.
- 1 October 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 27  (5)
Postbuckling Behavior of FRP Bending-Active Arches Subjected to a Central Point Load
- 1 October 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 27  (5)
Postbuckling Behavior of FRP Bending-Active Arches Subjected to a Central Point Load
- 7 June 2023
- Published by SAGE Publications in Advances in Structural Engineering
- Vol. 26  (13) , 2341-2358
Innovating arch structures with fiber-reinforced polymer composites: A review
Fiber-reinforced polymer (FRP) composites are a class of advanced non-metallic materials featuring advantages of high strength, light weight and excellent corrosion resistance. These advantages, in conjunction with the various methods available for making curved FRP members, create a wide range of possibilities for innovating arch structures with FRP composites. However, this subject has received inadequate research attention despite the exciting prospects demonstrated by pioneer studies. This paper provides a review on this subject with the aim to build a holistic picture and engage wider research participation. The paper begins with an overview of four feasible manufacturing/forming methods (vacuum infusion, filament winding, pultrusion and active bending), with an emphasis on their capability of creating curved FRP members and potential applications in arch structures. A review is next made on previous arch projects and relevant novel concepts, which are classified into two categories (all-FRP arches and FRP-incorporating hybrid arches) with distinct functionality and targeted areas of application. On the basis of this review, directions for future development of each of the two categories are highlighted, with a number of challenges and potential solutions discussed.
- 7 June 2023
- Published by SAGE Publications in Advances in Structural Engineering
- Vol. 26  (13) , 2341-2358
Innovating arch structures with fiber-reinforced polymer composites: A review
Fiber-reinforced polymer (FRP) composites are a class of advanced non-metallic materials featuring advantages of high strength, light weight and excellent corrosion resistance. These advantages, in conjunction with the various methods available for making curved FRP members, create a wide range of possibilities for innovating arch structures with FRP composites. However, this subject has received inadequate research attention despite the exciting prospects demonstrated by pioneer studies. This paper provides a review on this subject with the aim to build a holistic picture and engage wider research participation. The paper begins with an overview of four feasible manufacturing/forming methods (vacuum infusion, filament winding, pultrusion and active bending), with an emphasis on their capability of creating curved FRP members and potential applications in arch structures. A review is next made on previous arch projects and relevant novel concepts, which are classified into two categories (all-FRP arches and FRP-incorporating hybrid arches) with distinct functionality and targeted areas of application. On the basis of this review, directions for future development of each of the two categories are highlighted, with a number of challenges and potential solutions discussed.
- 1 February 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 27  (1) , 04022103
Compressive Behavior of GFRP Tubes Filled with Self-Compacting Concrete
Self-compacting concrete (SCC) features excellent flow ability without the need of vibration for compaction during casting. This makes it particularly suitable for application in hybrid fiber-reinforced polymer (FRP)-concrete–steel double-skin tubular columns (DSTCs), a high-performance structural form evolved from concrete-filled FRP tubes (CFFTs). In a DSTC, the space between the inner steel tube and the outer FRP tube for filling concrete may be narrow and the application of vibration may be difficult. However, because of the large shrinkage of SCC compared to traditional concrete of normal flow ability, the integrity and composite action of DSTCs with SCC become a major concern. To clarify this issue, an understanding of the behavior of CFFTs filled with SCC is an essential prerequisite. While a large number of studies have been published on CFFTs with normal concrete (NC), only limited studies have been carried out on CFFTs with SCC. This paper presents a comprehensive investigation on the effect of SCC on the behavior of large-scale CFFTs. Axial compression tests were carried out on concrete-filled glass FRP (GFRP) tubes with diameters of 150, 200, 300, and 400 mm. The compressive behavior of the CFFT specimens filled with NC, a nonexpansive SCC, and an expansive SCC (ESCC) was compared and discussed. The results showed that the specimens with nonexpansive SCC behaved differently compared to those with NC as a result of larger shrinkage, especially for large specimens for which the confinement level was lower. This situation, however, improved in specimens where ESCC was used. Finally, the test results were further analyzed using a theoretical model recently proposed by the authors’ group. This paper investigates the compressive behavior of glass fiber–reinforced polymer (GFRP) tubes filled with self-compacting concrete (SCC). SCC is a type of concrete featuring excellent flow ability and larger shrinkage than normal concrete (NC). The detrimental effect of shrinkage can be counterbalanced by using expansive cement to form expansive SCC (ESCC). Compression tests were conducted on SCC-, NC-, and ESCC-filled GFRP tubes. Their compressive behavior was compared and analyzed. It was found that the NC- and ESCC-filled specimens behaved similarly, while the SCC-filled specimens showed a stronger dilation tendency under axial compression and less satisfactory performance than their NC- and ESCC-filled counterparts when the confinement level was relatively weak. Therefore, the use of an appropriate amount of expansive cement or a strong level of confinement is recommended when SCC is used as the concrete infill in practical confinement applications. The findings of this study are useful for applications of SCC in composite columns, especially in situations where only a narrow space is available for concrete casting, such as casting composite columns with a narrow ring section.
- 1 February 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 27  (1) , 04022103
Compressive Behavior of GFRP Tubes Filled with Self-Compacting Concrete
Self-compacting concrete (SCC) features excellent flow ability without the need of vibration for compaction during casting. This makes it particularly suitable for application in hybrid fiber-reinforced polymer (FRP)-concrete–steel double-skin tubular columns (DSTCs), a high-performance structural form evolved from concrete-filled FRP tubes (CFFTs). In a DSTC, the space between the inner steel tube and the outer FRP tube for filling concrete may be narrow and the application of vibration may be difficult. However, because of the large shrinkage of SCC compared to traditional concrete of normal flow ability, the integrity and composite action of DSTCs with SCC become a major concern. To clarify this issue, an understanding of the behavior of CFFTs filled with SCC is an essential prerequisite. While a large number of studies have been published on CFFTs with normal concrete (NC), only limited studies have been carried out on CFFTs with SCC. This paper presents a comprehensive investigation on the effect of SCC on the behavior of large-scale CFFTs. Axial compression tests were carried out on concrete-filled glass FRP (GFRP) tubes with diameters of 150, 200, 300, and 400 mm. The compressive behavior of the CFFT specimens filled with NC, a nonexpansive SCC, and an expansive SCC (ESCC) was compared and discussed. The results showed that the specimens with nonexpansive SCC behaved differently compared to those with NC as a result of larger shrinkage, especially for large specimens for which the confinement level was lower. This situation, however, improved in specimens where ESCC was used. Finally, the test results were further analyzed using a theoretical model recently proposed by the authors’ group. This paper investigates the compressive behavior of glass fiber–reinforced polymer (GFRP) tubes filled with self-compacting concrete (SCC). SCC is a type of concrete featuring excellent flow ability and larger shrinkage than normal concrete (NC). The detrimental effect of shrinkage can be counterbalanced by using expansive cement to form expansive SCC (ESCC). Compression tests were conducted on SCC-, NC-, and ESCC-filled GFRP tubes. Their compressive behavior was compared and analyzed. It was found that the NC- and ESCC-filled specimens behaved similarly, while the SCC-filled specimens showed a stronger dilation tendency under axial compression and less satisfactory performance than their NC- and ESCC-filled counterparts when the confinement level was relatively weak. Therefore, the use of an appropriate amount of expansive cement or a strong level of confinement is recommended when SCC is used as the concrete infill in practical confinement applications. The findings of this study are useful for applications of SCC in composite columns, especially in situations where only a narrow space is available for concrete casting, such as casting composite columns with a narrow ring section.
- Open Access
- 9 September 2022
- Published by Termedia Sp. z.o.o. in Archives of Medical Science
Association of the IL-4R Q576R polymorphism with asthma: A meta-analysis
Introduction: Several articles have examined the relationship of IL-4 receptor gene (IL-4R) polymorphisms with asthma, yet the results remain inconsistent. This may be attributed to the small sample sizes and polymorphism’s small effect size that fail to offer potent statistical power....
- 9 September 2022
- Published by Termedia Sp. z.o.o. in Archives of Medical Science
Open AccessAssociation of the IL-4R Q576R polymorphism with asthma: A meta-analysis
Introduction: Several articles have examined the relationship of IL-4 receptor gene (IL-4R) polymorphisms with asthma, yet the results remain inconsistent. This may be attributed to the small sample sizes and polymorphism’s small effect size that fail to offer potent statistical power....
- 1 August 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 26  (4) , 04022035
Path-Dependent Stress–Strain Model for FRP-Confined Recycled Brick Aggregate Concrete
Fiber-reinforced polymer (FRP) confinement has shown promise as an alternative method aimed at enabling the structural use of recycled brick aggregate concrete (RBAC) in columns. To facilitate practical applications, an existing stress–strain model for FRP-confined normal concrete is modified in this paper to extend its applicability to FRP-confined RBAC. The modification was based on a rigorous approach involving a direct examination of the path-independent assumption, which was made possible by conducting companion tests on actively confined and FRP-confined RBAC. Comparisons of the stress–strain and dilation responses obtained from the two confinement schemes showed that the axial strain of RBAC can be considered path-independent while the axial stress of RBAC tends to be path-dependent. The underlying cause is probably that the weak resistance of recycled brick aggregate (RBA) makes itself a medium for crack propagation. The effect of path dependence is accounted for in the modified model by purposefully weakening the stress–strain response of actively confined RBAC to correct the overestimate found in the axial stresses of FRP-confined RBAC, which originates from adopting the path-independent assumption.
- 1 August 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 26  (4) , 04022035
Path-Dependent Stress–Strain Model for FRP-Confined Recycled Brick Aggregate Concrete
Fiber-reinforced polymer (FRP) confinement has shown promise as an alternative method aimed at enabling the structural use of recycled brick aggregate concrete (RBAC) in columns. To facilitate practical applications, an existing stress–strain model for FRP-confined normal concrete is modified in this paper to extend its applicability to FRP-confined RBAC. The modification was based on a rigorous approach involving a direct examination of the path-independent assumption, which was made possible by conducting companion tests on actively confined and FRP-confined RBAC. Comparisons of the stress–strain and dilation responses obtained from the two confinement schemes showed that the axial strain of RBAC can be considered path-independent while the axial stress of RBAC tends to be path-dependent. The underlying cause is probably that the weak resistance of recycled brick aggregate (RBA) makes itself a medium for crack propagation. The effect of path dependence is accounted for in the modified model by purposefully weakening the stress–strain response of actively confined RBAC to correct the overestimate found in the axial stresses of FRP-confined RBAC, which originates from adopting the path-independent assumption.
- 1 June 2022
- Published by British Institute of Non-Destructive Testing (BINDT) in Insight - Non-Destructive Testing and Condition Monitoring
- Vol. 64  (6) , 334-340
Experimental Analysis of the Piezomagnetic Properties of Ferromagnetic Steels Subjected To Cyclic Tensile Stress
The objective of this research is to investigate the evolution of the piezomagnetic field of 30CrNiMo8 steel under cyclic tensile stress with variable amplitudes and asymmetrical cyclic tensile stress. The piezomagnetic field signal of an initially undemagnetised 30CrNiMo8 steel specimen was recorded simultaneously during the whole loading process. It was found that the magnetic field variation is in contrast to the variation of the applied stress during the elastic stage. However, the magnetic field variation started to be consistent with the variation of the applied stress when approaching and entering the plastic stage. A reasonable explanation was given for understanding this phenomenon. The Villari reversal point and the tail reversal point occurred during the plastic stage, which can be used to characterise the transition state from the elastic to plastic stage. The variations of the Villari reversal point and the tail reversal point under cyclic tensile stress with variable amplitudes were slightly different from those under asymmetrical cyclic tensile stress.
- 1 June 2022
- Published by British Institute of Non-Destructive Testing (BINDT) in Insight - Non-Destructive Testing and Condition Monitoring
- Vol. 64  (6) , 334-340
Experimental Analysis of the Piezomagnetic Properties of Ferromagnetic Steels Subjected To Cyclic Tensile Stress
The objective of this research is to investigate the evolution of the piezomagnetic field of 30CrNiMo8 steel under cyclic tensile stress with variable amplitudes and asymmetrical cyclic tensile stress. The piezomagnetic field signal of an initially undemagnetised 30CrNiMo8 steel specimen was recorded simultaneously during the whole loading process. It was found that the magnetic field variation is in contrast to the variation of the applied stress during the elastic stage. However, the magnetic field variation started to be consistent with the variation of the applied stress when approaching and entering the plastic stage. A reasonable explanation was given for understanding this phenomenon. The Villari reversal point and the tail reversal point occurred during the plastic stage, which can be used to characterise the transition state from the elastic to plastic stage. The variations of the Villari reversal point and the tail reversal point under cyclic tensile stress with variable amplitudes were slightly different from those under asymmetrical cyclic tensile stress.
- 15 July 2020
- Published by Springer Nature in Earthquake Engineering and Engineering Vibration
- Vol. 19  (3) , 649-668
Novel uniaxial concrete constitutive model considering bond-slip effect
- 15 July 2020
- Published by Springer Nature in Earthquake Engineering and Engineering Vibration
- Vol. 19  (3) , 649-668
Novel uniaxial concrete constitutive model considering bond-slip effect
- 1 June 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 24  (3)
Erratum for “Compressive Behavior of CFRP-Confined Recycled Aggregate Concrete in Different-Sized Circular Sections” by G. M. Chen, J. J. Zhang, T. Jiang, C. J. Lin, and Y. H. He
- 1 June 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 24  (3)
Erratum for “Compressive Behavior of CFRP-Confined Recycled Aggregate Concrete in Different-Sized Circular Sections” by G. M. Chen, J. J. Zhang, T. Jiang, C. J. Lin, and Y. H. He