Raghuvir Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Raghuvir Singh has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
Charu Singh
CSIR-National Metallurgical Laboratory
2 shared publications- Lalit Kumar Meena
CSIR-National Metallurgical Laboratory
2 shared publications Narendra B. Dahotre
Department of Materials Science and Engineering, The University of North Texas, Denton, USA
2 shared publicationsA. Kumar
The National Metallurgical Laboratory
1 shared publication- Amar Nath Bhagat
Tata Steel Ltd., Jamshedpur, India
1 shared publication - Amarendra Kumar Sarma
Indian Institute of Technology Guwahati
1 shared publication
Latest Publications
- Open Access
- 8 April 2024
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 77 (5) , 1247-1248
Special Issue on Corrosion and Coating Technology
- 8 April 2024
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 77 (5) , 1247-1248
Open AccessSpecial Issue on Corrosion and Coating Technology
- 31 January 2024
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 77 (5) , 1361-1371
Sour Service Domains of 13Cr Martensitic Stainless Steels: A Review of State-of-Art Knowledge vis-à-vis ANSI/NACE MR0175/ISO 15156
- 31 January 2024
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 77 (5) , 1361-1371
Sour Service Domains of 13Cr Martensitic Stainless Steels: A Review of State-of-Art Knowledge vis-à-vis ANSI/NACE MR0175/ISO 15156
- 6 January 2024
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 77 (5) , 1329-1342
Flow-Assisted Corrosion of API 5L X56 Steel: Effect of Flow Velocity and Dissolved Oxygen
- 6 January 2024
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 77 (5) , 1329-1342
Flow-Assisted Corrosion of API 5L X56 Steel: Effect of Flow Velocity and Dissolved Oxygen
- 30 September 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (3) , 935-954
Integrity of Additively Manufactured Alloys and Component to Environmental Degradation
- 30 September 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (3) , 935-954
Integrity of Additively Manufactured Alloys and Component to Environmental Degradation
- 5 May 2022
- Published by Springer Nature
- p. 355-368
Corrosion Behavior of Magnesium and Its Alloys and Mitigation by Wet Deposition Methods
- 5 May 2022
- Published by Springer Nature
- p. 355-368
Corrosion Behavior of Magnesium and Its Alloys and Mitigation by Wet Deposition Methods
- 3 April 2022
- Published by Springer Nature
- p. 35-52
Effects of Strontium Addition on Corrosion Properties of Al-12Si Alloy
- 3 April 2022
- Published by Springer Nature
- p. 35-52
Effects of Strontium Addition on Corrosion Properties of Al-12Si Alloy
- 1 July 2019
- Published by Elsevier in Applied Surface Science
- Vol. 483, 334-354
Effect of carbonate and phosphate conversion pretreatments and optimization on corrosion behaviour of subsequent electroless nickel coating on AZ91 alloy
- 1 July 2019
- Published by Elsevier in Applied Surface Science
- Vol. 483, 334-354
Effect of carbonate and phosphate conversion pretreatments and optimization on corrosion behaviour of subsequent electroless nickel coating on AZ91 alloy
- 5 December 2017
- Published by SAGE Publications in Surface Engineering
- Vol. 36 (12) , 1285-1293
Influence of laser scanning speed on nitrided Ti6Al4V surface
The influence of laser scan speed during nitriding in the range 30–150 cm min −1 on the physical properties, microstructure and corrosion behaviour of Ti6Al4V was studied. The surface energy of nitrided Ti6Al4V remained almost constant up to the scan speed of 60 cm min −1 followed by an increase in the maximum value at 80 cm min −1 . A gradual drop in the microhardness of the coating from the outermost surface was noticed for specimens nitrided up to 80 cm min −1 ; an abrupt decrease, however, was found at a scan speed ≥100 cm min −1 . The laser nitriding produced dendritic microstructure; an exponential decay in the secondary dendrite arm spacing (SDAS) with the increase in laser scan speed was revealed. The SDAS produced was smaller at the interphase and centre of the coating, compared to that at outermost surface. The passivation behaviour of Ti6Al4V at lower potentials shifted to the smaller current side after laser nitriding.
- 5 December 2017
- Published by SAGE Publications in Surface Engineering
- Vol. 36 (12) , 1285-1293
Influence of laser scanning speed on nitrided Ti6Al4V surface
The influence of laser scan speed during nitriding in the range 30–150 cm min −1 on the physical properties, microstructure and corrosion behaviour of Ti6Al4V was studied. The surface energy of nitrided Ti6Al4V remained almost constant up to the scan speed of 60 cm min −1 followed by an increase in the maximum value at 80 cm min −1 . A gradual drop in the microhardness of the coating from the outermost surface was noticed for specimens nitrided up to 80 cm min −1 ; an abrupt decrease, however, was found at a scan speed ≥100 cm min −1 . The laser nitriding produced dendritic microstructure; an exponential decay in the secondary dendrite arm spacing (SDAS) with the increase in laser scan speed was revealed. The SDAS produced was smaller at the interphase and centre of the coating, compared to that at outermost surface. The passivation behaviour of Ti6Al4V at lower potentials shifted to the smaller current side after laser nitriding.
- 10 June 2011
- Published by Springer Nature in Journal of Materials Science: Materials in Medicine
- Vol. 22 (8) , 1787-1796
Electrochemical and mechanical behavior of laser processed Ti–6Al–4V surface in Ringer’s physiological solution
Laser surface modification of Ti–6Al–4V with an existing calcium phosphate coating has been conducted to enhance the surface properties. The electrochemical and mechanical behaviors of calcium phosphate deposited on a Ti–6Al–4V surface and remelted using a Nd:YAG laser at varying laser power densities (25–50 W/mm2) have been studied and the results are presented. The electrochemical properties of the modified surfaces in Ringer’s physiological solution were evaluated by employing both potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) methods. The potentiodynamic polarizations showed an increase in the passive current density of Ti–6Al–4V after laser modification at power densities up to 35 W/mm2, after which it exhibited a decrease. A reduction in the passive current density (by more than an order) was observed with an increase in the laser power density from 25 to 50 W/mm2. EIS studies at the open circuit potential (OCP) and in the passive region at 1.19 V showed that the polarization resistance increased from 8.274 × 103 to 4.38 × 105 Ω cm2 with increasing laser power densities. However, the magnitudes remain lower than that of the untreated Ti–6Al–4V at OCP. The average hardness and modulus of the laser treated Ti–6Al–4V, evaluated by the nanoindentation method, were determined to be 5.4–6.5 GPa (with scatter <±0.976 GPa) and 124–155 GPa (with scatter <±13 GPa) respectively. The corresponding hardness and modulus of untreated Ti–6Al–4V were ~4.1 (±0.62) and ~148 (±7) GPa respectively. Laser processing at power densities >35 W/mm2 enhanced the surface properties (as passive current density is reduced) so that the materials may be suitable for the biomedical applications.
- 10 June 2011
- Published by Springer Nature in Journal of Materials Science: Materials in Medicine
- Vol. 22 (8) , 1787-1796
Electrochemical and mechanical behavior of laser processed Ti–6Al–4V surface in Ringer’s physiological solution
Laser surface modification of Ti–6Al–4V with an existing calcium phosphate coating has been conducted to enhance the surface properties. The electrochemical and mechanical behaviors of calcium phosphate deposited on a Ti–6Al–4V surface and remelted using a Nd:YAG laser at varying laser power densities (25–50 W/mm2) have been studied and the results are presented. The electrochemical properties of the modified surfaces in Ringer’s physiological solution were evaluated by employing both potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) methods. The potentiodynamic polarizations showed an increase in the passive current density of Ti–6Al–4V after laser modification at power densities up to 35 W/mm2, after which it exhibited a decrease. A reduction in the passive current density (by more than an order) was observed with an increase in the laser power density from 25 to 50 W/mm2. EIS studies at the open circuit potential (OCP) and in the passive region at 1.19 V showed that the polarization resistance increased from 8.274 × 103 to 4.38 × 105 Ω cm2 with increasing laser power densities. However, the magnitudes remain lower than that of the untreated Ti–6Al–4V at OCP. The average hardness and modulus of the laser treated Ti–6Al–4V, evaluated by the nanoindentation method, were determined to be 5.4–6.5 GPa (with scatter <±0.976 GPa) and 124–155 GPa (with scatter <±13 GPa) respectively. The corresponding hardness and modulus of untreated Ti–6Al–4V were ~4.1 (±0.62) and ~148 (±7) GPa respectively. Laser processing at power densities >35 W/mm2 enhanced the surface properties (as passive current density is reduced) so that the materials may be suitable for the biomedical applications.