Carlos Couso
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Carlos Couso has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Marc Porti
Departament dEnginyeria Electrnica, Universitat Autnoma de Barcelona, Barcelona, Spain
10 shared publications - Montserrat Nafria
Departament dEnginyeria Electrnica, Universitat Autnoma de Barcelona, Barcelona, Spain
10 shared publications - Javier Martin-Martinez
Department of Electronic Engineering, Universitat Autónoma of Barcelona, 08193 Bellaterra, Spain
7 shared publications - Maria Jesus Martin
Departamento de Física Aplicada, Universidad de Salamanca, Salamanca, Castilla y León, SPAIN
5 shared publications - Raúl Rengel
Departamento de Fisica Aplicada, University of Salamanca, Plaza de la Merced s/n, 37008 Salamanca, Salamanca, SPAIN
4 shared publications - Antonio Jesus García Loureiro
CiTIUS, University of Santiago de Compostela, Santiago de Compostela, Spain
3 shared publications
Latest Publications
- Open Access
- 23 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 90568-90576
Methodology for the Simulation of the Variability of MOSFETs With Polycrystalline High-k Dielectrics Using CAFM Input Data
In this work, a simulation methodology, whose inputs are Conductive Atomic Force Microscope (CAFM) experimental data, is proposed to evaluate the impact of nanoscale variability sources related to the polycrystallization of high-k dielectrics (i.e., oxide thickness, t ox , and charge density, ρ ox , fluctuations in the nanometer range) on the Metal-Oxide-Semiconductor Field Effect Transistor (MOSFET) variability. To simulate this variability, a Thickness And Charge MAp Generator (TACMAG) has been developed and used in combination with an in-house-built 3D device simulator (VENDES). From CAFM experimental data (topography and current) obtained on a small area of a given polycrystalline dielectric, the TACMAG generates a high amount of t ox and ρ ox configurations of the gate dielectric, with identical statistical characteristics to those experimentally measured. These dielectrics are then introduced into the device simulator, with which the impact of the t ox and ρ ox fluctuations in the dielectric on the variability of MOSFETs (i.e., threshold voltage) is analyzed. Finally, the impact of different nanoscale parameters, such as the Grain size and Grain Boundaries depth (of polycrystalline dielectrics) on such variability has been evaluated.
- 23 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 90568-90576
Open AccessMethodology for the Simulation of the Variability of MOSFETs With Polycrystalline High-k Dielectrics Using CAFM Input Data
In this work, a simulation methodology, whose inputs are Conductive Atomic Force Microscope (CAFM) experimental data, is proposed to evaluate the impact of nanoscale variability sources related to the polycrystallization of high-k dielectrics (i.e., oxide thickness, t ox , and charge density, ρ ox , fluctuations in the nanometer range) on the Metal-Oxide-Semiconductor Field Effect Transistor (MOSFET) variability. To simulate this variability, a Thickness And Charge MAp Generator (TACMAG) has been developed and used in combination with an in-house-built 3D device simulator (VENDES). From CAFM experimental data (topography and current) obtained on a small area of a given polycrystalline dielectric, the TACMAG generates a high amount of t ox and ρ ox configurations of the gate dielectric, with identical statistical characteristics to those experimentally measured. These dielectrics are then introduced into the device simulator, with which the impact of the t ox and ρ ox fluctuations in the dielectric on the variability of MOSFETs (i.e., threshold voltage) is analyzed. Finally, the impact of different nanoscale parameters, such as the Grain size and Grain Boundaries depth (of polycrystalline dielectrics) on such variability has been evaluated.
- 4 March 2019
- Published by AIP Publishing in Applied Physics Letters
- Vol. 114 (9) , 093502
Workfunction fluctuations in polycrystalline TiN observed with KPFM and their impact on MOSFETs variability
A more realistic approach to evaluate the impact of polycrystalline metal gates on the MOSFET variability is presented. 2D experimental workfunction maps of a polycrystalline TiN layer were obtained by Kelvin Probe Force Microscopy with a nanometer resolution. These data were the input of a device simulator, which allowed us to evaluate the effect of the workfunction fluctuations on MOSFET performance variability. We have demonstrated that in the modelling of TiN workfunction variability not only the different workfunctions of the grains but also the grain boundaries should be included.
- 4 March 2019
- Published by AIP Publishing in Applied Physics Letters
- Vol. 114 (9) , 093502
Workfunction fluctuations in polycrystalline TiN observed with KPFM and their impact on MOSFETs variability
A more realistic approach to evaluate the impact of polycrystalline metal gates on the MOSFET variability is presented. 2D experimental workfunction maps of a polycrystalline TiN layer were obtained by Kelvin Probe Force Microscopy with a nanometer resolution. These data were the input of a device simulator, which allowed us to evaluate the effect of the workfunction fluctuations on MOSFET performance variability. We have demonstrated that in the modelling of TiN workfunction variability not only the different workfunctions of the grains but also the grain boundaries should be included.
- Open Access
- 9 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 6 (1) , 55-62
Performance and Power Consumption Trade-Off in UTBB FDSOI Inverters Operated at NTV for IoT Applications
Power consumption and I on /I off ratio of an ultra-thin body and buried oxide fully depleted silicon on insulator CMOS inverter circuit has been calculated at near-threshold voltage operation from TCAD simulations. TCAD outputs (current, voltage, and capacitance) were used as parameters to solve the inverter circuit. Besides, a bias operation point (V OP ) has been proposed, which provides a good trade-off between the I on /I off ratio and the energy consumption. Variations of this operation point, due to the presence of interface traps, have been also analyzed.
- 9 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 6 (1) , 55-62
Open AccessPerformance and Power Consumption Trade-Off in UTBB FDSOI Inverters Operated at NTV for IoT Applications
Power consumption and I on /I off ratio of an ultra-thin body and buried oxide fully depleted silicon on insulator CMOS inverter circuit has been calculated at near-threshold voltage operation from TCAD simulations. TCAD outputs (current, voltage, and capacitance) were used as parameters to solve the inverter circuit. Besides, a bias operation point (V OP ) has been proposed, which provides a good trade-off between the I on /I off ratio and the energy consumption. Variations of this operation point, due to the presence of interface traps, have been also analyzed.
- 1 June 2017
- Published by Elsevier in Microelectronic Engineering
- Vol. 178, 66-70
Efficient methodology to extract interface traps parameters for TCAD simulations
- 1 June 2017
- Published by Elsevier in Microelectronic Engineering
- Vol. 178, 66-70
Efficient methodology to extract interface traps parameters for TCAD simulations
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 87-90
Dependence of MOSFETs threshold voltage variability on channel dimensions
The dependence of the MOSFET threshold voltage variability on device geometry (width (W) and length (L)) has been studied from experimental data. Our results evidence, in agreement with other works, deviations from the Pelgrom's rule, especially in smaller technologies. TCAD simulations were also performed which further support the experimental data and provide physical information regarding the origin of such deviation. Finally, a new empirical model that assumes different impact of W and L in the device variability has been proposed, which reproduces the experimental results.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 87-90
Dependence of MOSFETs threshold voltage variability on channel dimensions
The dependence of the MOSFET threshold voltage variability on device geometry (width (W) and length (L)) has been studied from experimental data. Our results evidence, in agreement with other works, deviations from the Pelgrom's rule, especially in smaller technologies. TCAD simulations were also performed which further support the experimental data and provide physical information regarding the origin of such deviation. Finally, a new empirical model that assumes different impact of W and L in the device variability has been proposed, which reproduces the experimental results.
- 9 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (5) , 637-640
Local Defect Density in Polycrystalline High-k Dielectrics: CAFM-Based Evaluation Methodology and Impact on MOSFET Variability
A methodology to determine with nanometer resolution the defect density in polycrystalline HfO2 layers has been developed. This methodology is based on experimental data measured with conductive atomic force microscopy and the obtained results have been validated using Kelvin prove force microscopy measurements. The local defect density ( ρox ) and thickness (t ox ) of the gate dielectric have been included into a device simulator to evaluate their impact on the I D V G curves of MOSFETs.
- 9 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (5) , 637-640
Local Defect Density in Polycrystalline High-k Dielectrics: CAFM-Based Evaluation Methodology and Impact on MOSFET Variability
A methodology to determine with nanometer resolution the defect density in polycrystalline HfO2 layers has been developed. This methodology is based on experimental data measured with conductive atomic force microscopy and the obtained results have been validated using Kelvin prove force microscopy measurements. The local defect density ( ρox ) and thickness (t ox ) of the gate dielectric have been included into a device simulator to evaluate their impact on the I D V G curves of MOSFETs.
- Open Access
- 1 March 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 37 (5) , 640-643
Conductance of Threading Dislocations in InGaAs/Si Stacks by Temperature-CAFM Measurements
The stacks of III-V materials, grown on the Si substrate, that are considered for the fabrication of highly scaled devices tend to develop structural defects, in particular threading dislocations (TDs), which affect device electrical properties. We demonstrate that the characteristics of the TD sites can be analyzed by using the conductive atomic force microscopy technique with nanoscale spatial resolution within a wide temperature range. In the studied InGaAs/Si stacks, electrical conductance through the TD sites was found to be governed by the Poole-Frenkel emission, while the off-TDs conductivity is dominated by the thermionic emission process.
- 1 March 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 37 (5) , 640-643
Open AccessConductance of Threading Dislocations in InGaAs/Si Stacks by Temperature-CAFM Measurements
The stacks of III-V materials, grown on the Si substrate, that are considered for the fabrication of highly scaled devices tend to develop structural defects, in particular threading dislocations (TDs), which affect device electrical properties. We demonstrate that the characteristics of the TD sites can be analyzed by using the conductive atomic force microscopy technique with nanoscale spatial resolution within a wide temperature range. In the studied InGaAs/Si stacks, electrical conductance through the TD sites was found to be governed by the Poole-Frenkel emission, while the off-TDs conductivity is dominated by the thermionic emission process.
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19308876,p. 230-233
Threshold voltage and on-current Variability related to interface traps spatial distribution
Interface traps can be a source of variability in MOSFETs, leading to statistically distributed electrical characteristics of devices. This work discusses, from 3D TCAD simulations, the effect of the spatial distribution of interface traps on the variability of the threshold voltage and the on-current of MOSFETs. The results suggest that threshold voltage is mainly influenced by the trap distribution along the channel of the device, whereas on-current is also influenced by the alignment of the traps along the device width. Implications for device electrical symmetry are discussed.
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19308876,p. 230-233
Threshold voltage and on-current Variability related to interface traps spatial distribution
Interface traps can be a source of variability in MOSFETs, leading to statistically distributed electrical characteristics of devices. This work discusses, from 3D TCAD simulations, the effect of the spatial distribution of interface traps on the variability of the threshold voltage and the on-current of MOSFETs. The results suggest that threshold voltage is mainly influenced by the trap distribution along the channel of the device, whereas on-current is also influenced by the alignment of the traps along the device width. Implications for device electrical symmetry are discussed.
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. CD.4.1-CD.4.6
Threading dislocations in III-V semiconductors: Analysis of electrical conduction
The implementation of devices with high mobility substrates requires growing III-V semiconductors over the underlying silicon substrates. However, due to the lattice mismatch, III-V materials tend to develop a significant density of structural defects, which may affect the device electrical characteristics. In this study, Threading Dislocation (TD) defects, which may propagate through the III-V layers, were studied using Conductive Atomic force Microscopy (CAFM). This technique is shown to be effective for identification and analysis at the nanoscale of the pre- and post-electrically stressed TD. The TD conduction studied at different temperatures (T) is shown to be consistent with the Poole-Frenkel (PF) emission process.
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. CD.4.1-CD.4.6
Threading dislocations in III-V semiconductors: Analysis of electrical conduction
The implementation of devices with high mobility substrates requires growing III-V semiconductors over the underlying silicon substrates. However, due to the lattice mismatch, III-V materials tend to develop a significant density of structural defects, which may affect the device electrical characteristics. In this study, Threading Dislocation (TD) defects, which may propagate through the III-V layers, were studied using Conductive Atomic force Microscopy (CAFM). This technique is shown to be effective for identification and analysis at the nanoscale of the pre- and post-electrically stressed TD. The TD conduction studied at different temperatures (T) is shown to be consistent with the Poole-Frenkel (PF) emission process.
- Open Access
- 20 March 2015
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 33 (3)
Conductive-AFM topography and current maps simulator for the study of polycrystalline high-k dielectrics
In this work, a simulator of conductive atomic force microscopy (C-AFM) was developed to reproduce topography and current maps. In order to test the results, the authors used the simulator to investigate the influence of the C-AFM tip on topography measurements of polycrystalline high-k dielectrics, and compared the results with experimental data. The results show that this tool can produce topography images with the same morphological characteristics as the experimental samples under study. Additionally, the current at each location of the dielectric stack was calculated. The quantum mechanical transmission coefficient and tunneling current were obtained from the band diagram by applying the Airy wavefunction approach. Good agreement between experimental and simulation results indicates that the tool can be very useful for evaluating how the experimental parameters influence C-AFM measurements.
- 20 March 2015
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 33 (3)
Open AccessConductive-AFM topography and current maps simulator for the study of polycrystalline high-k dielectrics
In this work, a simulator of conductive atomic force microscopy (C-AFM) was developed to reproduce topography and current maps. In order to test the results, the authors used the simulator to investigate the influence of the C-AFM tip on topography measurements of polycrystalline high-k dielectrics, and compared the results with experimental data. The results show that this tool can produce topography images with the same morphological characteristics as the experimental samples under study. Additionally, the current at each location of the dielectric stack was calculated. The quantum mechanical transmission coefficient and tunneling current were obtained from the band diagram by applying the Airy wavefunction approach. Good agreement between experimental and simulation results indicates that the tool can be very useful for evaluating how the experimental parameters influence C-AFM measurements.