Ali Zadhoush
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ali Zadhoush has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Mohammadreza Naeimirad
Department of Materials and Textile Engineering, Faculty of Engineering, Razi University, Kermanshah 67144-14971, Iran
7 shared publications M. Haghighat
Chemical Engineering Department, Isfahan University of Technology, Isfahan 84156, Iran
5 shared publications- Saeed Salimian
Department of Textile Engineering, Isfahan University of Technology, Isfahan, Iran
4 shared publications - Ashkan Heidarkhan Tehrani
Department of Textile Engineering, Isfahan University of Technology, 84156-83111, Isfahan, Iran
3 shared publications - Rasoul Esmaeely Neisiany
Department of Polymer Engineering, Hakim Sabzevari University, Sabzevar, Iran
3 shared publications - Saeed Karbasi
Department of Biomaterials, Nanotechnology and Tissue Engineering, School of Advanced Technologies in Medicine, Isfahan University of Medical Sciences, Isfahan, Iran
3 shared publications
Latest Publications
- 8 March 2021
- Published by Wiley in Polymer Composites
- Vol. 42 (5) , 2422-2431
Self‐healing performance of hybrid core‐shell nanofibers mat containing epoxy‐mercaptan at subroom temperature
Self‐healing epoxy composite working at subroom temperature could be useful in aerospace industry and wind turbine blades. In this research, hybrid core‐shell nanofibers mat containing epoxy resin and mercaptan was embedded in epoxy matrix to investigate repeated self‐healing ability of the fabricated composite at subroom temperature (10°C). The results of three‐point bending test illustrated that the release of epoxy resin and mercaptan into cracks and curing reaction between them could restore flexural properties of the composite. In fourth bending cycle, flexural modulus of composite reinforced by hybrid mat and unreinforced epoxy (without nanofiber) was reduced 6% and 24%, respectively. In addition, hybrid mat reinforced composite was broken at fifth bending cycle whereas for unreinforced epoxy specimen occurred at fourth bending cycle. Non‐isothermal differential scanning calorimetry thermograms after each three‐point bending cycle of hybrid mat reinforced composite showed an exothermic peak centered about 64°C. This peak is related to epoxy and mercaptan reaction that could confirm self‐healing ability of hybrid core‐shell nanofibers mat. Extraction results, FTIR analysis, and three‐point bending test showed the stability of epoxy and mercaptan into nanofibers during 8 months.
- 8 March 2021
- Published by Wiley in Polymer Composites
- Vol. 42 (5) , 2422-2431
Self‐healing performance of hybrid core‐shell nanofibers mat containing epoxy‐mercaptan at subroom temperature
Self‐healing epoxy composite working at subroom temperature could be useful in aerospace industry and wind turbine blades. In this research, hybrid core‐shell nanofibers mat containing epoxy resin and mercaptan was embedded in epoxy matrix to investigate repeated self‐healing ability of the fabricated composite at subroom temperature (10°C). The results of three‐point bending test illustrated that the release of epoxy resin and mercaptan into cracks and curing reaction between them could restore flexural properties of the composite. In fourth bending cycle, flexural modulus of composite reinforced by hybrid mat and unreinforced epoxy (without nanofiber) was reduced 6% and 24%, respectively. In addition, hybrid mat reinforced composite was broken at fifth bending cycle whereas for unreinforced epoxy specimen occurred at fourth bending cycle. Non‐isothermal differential scanning calorimetry thermograms after each three‐point bending cycle of hybrid mat reinforced composite showed an exothermic peak centered about 64°C. This peak is related to epoxy and mercaptan reaction that could confirm self‐healing ability of hybrid core‐shell nanofibers mat. Extraction results, FTIR analysis, and three‐point bending test showed the stability of epoxy and mercaptan into nanofibers during 8 months.
- 2 May 2018
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 110 (1) , 89-99
Melt-spun PLA liquid-filled fibers: physical, morphological, and thermal properties
PLA hollow fibers with different internal diameters were produced as a media for liquid encapsulation via high-speed melt-spinning process, changing important parameters (e.g. material type, polymer throughput, extrusion temperature, quench flow rate, drawing ratio, and winding speed). Morphological analysis showed 300% increment (linear mode) for internal and outer diameters by increasing the polymer throughput from 14.6 to 87.6 ml/min while raising the winding speed from 500 to 1500 m/min resulted in decreasing 70 and 75% for internal and external diameters, respectively. Quench flow rate and extrusion temperature showed lower effect on just internal diameter. XRD patterns indicated that using higher drawing ratio led to increase in the fiber crystallinity. According to the physical studies, although the linear density was duplicated about 10 times by increasing the polymer throughput, but the winding speed reduced 300%. Adding the polymer throughput, as the main factor, caused the tensile strength, elongation at break, modulus, tenacity, and fracture toughness to be changed approximately +650%,+217%, –68%, –58%, and +1500%, respectively. Other parameters also influenced (described in text) on tensile performances. Thermal analysis showed lower thermal stability for the fibers extruded at higher temperature. DSC results also confirmed the same trend in the degree of crystallinity of the melt-spun fibers. Melt-spun fibers were filled with glycerol as a model liquid using the previously developed microfluidic approach. Biodegradable liquid-filled fibers were conducted on composting test. Successful biodegradation is a promising result for potential applications such as agriculture pesticide and medical drug delivery.
- 2 May 2018
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 110 (1) , 89-99
Melt-spun PLA liquid-filled fibers: physical, morphological, and thermal properties
PLA hollow fibers with different internal diameters were produced as a media for liquid encapsulation via high-speed melt-spinning process, changing important parameters (e.g. material type, polymer throughput, extrusion temperature, quench flow rate, drawing ratio, and winding speed). Morphological analysis showed 300% increment (linear mode) for internal and outer diameters by increasing the polymer throughput from 14.6 to 87.6 ml/min while raising the winding speed from 500 to 1500 m/min resulted in decreasing 70 and 75% for internal and external diameters, respectively. Quench flow rate and extrusion temperature showed lower effect on just internal diameter. XRD patterns indicated that using higher drawing ratio led to increase in the fiber crystallinity. According to the physical studies, although the linear density was duplicated about 10 times by increasing the polymer throughput, but the winding speed reduced 300%. Adding the polymer throughput, as the main factor, caused the tensile strength, elongation at break, modulus, tenacity, and fracture toughness to be changed approximately +650%,+217%, –68%, –58%, and +1500%, respectively. Other parameters also influenced (described in text) on tensile performances. Thermal analysis showed lower thermal stability for the fibers extruded at higher temperature. DSC results also confirmed the same trend in the degree of crystallinity of the melt-spun fibers. Melt-spun fibers were filled with glycerol as a model liquid using the previously developed microfluidic approach. Biodegradable liquid-filled fibers were conducted on composting test. Successful biodegradation is a promising result for potential applications such as agriculture pesticide and medical drug delivery.
- 26 March 2018
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 37 (11) , 738-769
A review on new mesostructured composite materials: Part II. Characterization and properties of polymer–mesoporous silica nanocomposite
Hybrid inorganic–organic materials are promising systems for a variety of applications due to their extraordinary properties with intricate composite architectures composed of nanoscale inorganic moieties with organic polymers synergistically intertwined to provide both useful functionality and mechanical integrity. These materials have a high potential for future applications and therefore attract considerable interest in polymer science research during the last years. Among the various explored inorganic nanostructures, the mesoporous silica has been considered as a fascinating material to construct novel ordered and well-dispersed nanocomposites due to their high surface areas, periodic and size-controllable pore channels. This review is written with the intention to give an overview of the characterization and material properties of polymer–mesoporous silica nanocomposites. Among polymer–mesoporous silica composites, various categories including polyaniline, polypyrrole, polystyrene, polypropylene, polyethylene, epoxy, rubber, and acrylate polymer were discussed in detail.
- 26 March 2018
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 37 (11) , 738-769
A review on new mesostructured composite materials: Part II. Characterization and properties of polymer–mesoporous silica nanocomposite
Hybrid inorganic–organic materials are promising systems for a variety of applications due to their extraordinary properties with intricate composite architectures composed of nanoscale inorganic moieties with organic polymers synergistically intertwined to provide both useful functionality and mechanical integrity. These materials have a high potential for future applications and therefore attract considerable interest in polymer science research during the last years. Among the various explored inorganic nanostructures, the mesoporous silica has been considered as a fascinating material to construct novel ordered and well-dispersed nanocomposites due to their high surface areas, periodic and size-controllable pore channels. This review is written with the intention to give an overview of the characterization and material properties of polymer–mesoporous silica nanocomposites. Among polymer–mesoporous silica composites, various categories including polyaniline, polypyrrole, polystyrene, polypropylene, polyethylene, epoxy, rubber, and acrylate polymer were discussed in detail.
- 26 February 2018
- Published by Wiley in Polymer Composites
- Vol. 40 (S1) , E501-E510
Evaluation of surface modification impact on PP/MWCNT nanocomposites by rheological and mechanical characterization, assisted with morphological image processing
PP/MWCNT nanocomposites were prepared using polypropylene and modified carbon nanotubes (CNTs) via melt‐extrusion process. Pure PP was compared with maleic anhydride grafted polypropylene, reinforced with 0.5, 1, and 1.5 wt% COOH‐modified nanotubes (PPgCNT) and polypropylene/unmodified CNT nanocomposite (PPCNT) in 1 wt% content. Morphological analysis was performed using FTIR and SEM along with MATLAB and easy fit software‐assisted image processing. Image processing of SEM monographs for well‐distributed CNTs showed a distribution factor (β) close to 0 while β in agglomerated samples was close to 1. Mechanical properties showed that tensile strength and tensile modulus of nanocomposites were higher than pure PP, in contrast the tensile elongation at break was lower. In addition, nanocomposites with modified nanotubes showed higher tensile strength, tensile modulus, and lower elongation at break compare with unmodified CNT/PP nanocomposites. Capillary rheometries resulted that at high strain rate [100–1500 (s−1)], melting behavior of the samples is similar to the viscoplastic fluids, and Herschel‐Bulkley model is the best approach for prediction of the fluid's rheological behaviors. Adding the modified and unmodified CNTs only changed the model's parameters. Oscillating rheometry studies concluded that at 1% strain, molten nanocomposites followed the viscoelastic behavior while in higher shear rates flow behavior is different. According to the oscillatory rheometry results, storage modulus, loss modulus, complex modulus, and complex viscosity of PPgCNTs were higher than PP and PPCNT. It is concluded that by reduction of β, nanocomposites become more viscoplastic (in high shear rates). Finally, statistical analysis confirmed the rheological and mechanical results. POLYM. COMPOS., 40:E501–E510, 2019. © 2018 Society of Plastics Engineers
- 26 February 2018
- Published by Wiley in Polymer Composites
- Vol. 40 (S1) , E501-E510
Evaluation of surface modification impact on PP/MWCNT nanocomposites by rheological and mechanical characterization, assisted with morphological image processing
PP/MWCNT nanocomposites were prepared using polypropylene and modified carbon nanotubes (CNTs) via melt‐extrusion process. Pure PP was compared with maleic anhydride grafted polypropylene, reinforced with 0.5, 1, and 1.5 wt% COOH‐modified nanotubes (PPgCNT) and polypropylene/unmodified CNT nanocomposite (PPCNT) in 1 wt% content. Morphological analysis was performed using FTIR and SEM along with MATLAB and easy fit software‐assisted image processing. Image processing of SEM monographs for well‐distributed CNTs showed a distribution factor (β) close to 0 while β in agglomerated samples was close to 1. Mechanical properties showed that tensile strength and tensile modulus of nanocomposites were higher than pure PP, in contrast the tensile elongation at break was lower. In addition, nanocomposites with modified nanotubes showed higher tensile strength, tensile modulus, and lower elongation at break compare with unmodified CNT/PP nanocomposites. Capillary rheometries resulted that at high strain rate [100–1500 (s−1)], melting behavior of the samples is similar to the viscoplastic fluids, and Herschel‐Bulkley model is the best approach for prediction of the fluid's rheological behaviors. Adding the modified and unmodified CNTs only changed the model's parameters. Oscillating rheometry studies concluded that at 1% strain, molten nanocomposites followed the viscoelastic behavior while in higher shear rates flow behavior is different. According to the oscillatory rheometry results, storage modulus, loss modulus, complex modulus, and complex viscosity of PPgCNTs were higher than PP and PPCNT. It is concluded that by reduction of β, nanocomposites become more viscoplastic (in high shear rates). Finally, statistical analysis confirmed the rheological and mechanical results. POLYM. COMPOS., 40:E501–E510, 2019. © 2018 Society of Plastics Engineers
- 14 February 2018
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (21)
Recent advances in core/shell bicomponent fibers and nanofibers: A review
There has been a steady progress in developing synthetic fibers in the past few years. Bicomponent fibers and nanofibers in a core/shell (C/S) configuration, including two dissimilar materials have presented unusual potential for use in many novel applications. These fibers can be produced using a variety of materials via different techniques i.e., coaxial melt spinning and electrospinning. In this review, we discuss the recent advances in C/S fibers and nanofibers’ production. The first part has been assigned to the bicomponent fibers manufacturing technology, while production and applications of C/S nanofibers have been described in the second part. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci.2018,135, 46265.
- 14 February 2018
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (21)
Recent advances in core/shell bicomponent fibers and nanofibers: A review
There has been a steady progress in developing synthetic fibers in the past few years. Bicomponent fibers and nanofibers in a core/shell (C/S) configuration, including two dissimilar materials have presented unusual potential for use in many novel applications. These fibers can be produced using a variety of materials via different techniques i.e., coaxial melt spinning and electrospinning. In this review, we discuss the recent advances in C/S fibers and nanofibers’ production. The first part has been assigned to the bicomponent fibers manufacturing technology, while production and applications of C/S nanofibers have been described in the second part. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci.2018,135, 46265.
- 10 January 2018
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 37 (7) , 441-459
A review on new mesostructured composite materials: Part I. synthesis of polymer-mesoporous silica nanocomposite
Mesoporous silicas are inorganic materials with large surface areas, uniform framework structures and readily controlled pore diameters which are synthesized in the presence of surfactants as structure-directing agents, followed by the removal of the surfactant by extraction or calcination. Due to their characteristics, such as ordered structure, high surface area, and favorable interfacial interactions between silica surface and the polymer, they have found excellent potential application for use as reinforcing agents for several engineering polymer systems. While a large number of different synthesis approaches for the preparation of mesoporous silica-polymer nanocomposites has been reported in literature, there is nevertheless a growing need for verified synthesis methods of mesoporous silica-polymer materials. This paper presents a review of the literature on the methods for synthesizing polymer-mesoporous silica nanocomposites and discusses some unique properties of these composites.
- 10 January 2018
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 37 (7) , 441-459
A review on new mesostructured composite materials: Part I. synthesis of polymer-mesoporous silica nanocomposite
Mesoporous silicas are inorganic materials with large surface areas, uniform framework structures and readily controlled pore diameters which are synthesized in the presence of surfactants as structure-directing agents, followed by the removal of the surfactant by extraction or calcination. Due to their characteristics, such as ordered structure, high surface area, and favorable interfacial interactions between silica surface and the polymer, they have found excellent potential application for use as reinforcing agents for several engineering polymer systems. While a large number of different synthesis approaches for the preparation of mesoporous silica-polymer nanocomposites has been reported in literature, there is nevertheless a growing need for verified synthesis methods of mesoporous silica-polymer materials. This paper presents a review of the literature on the methods for synthesizing polymer-mesoporous silica nanocomposites and discusses some unique properties of these composites.
- 14 November 2017
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 27 (1) , 1-11
Hybrid silane-treated glass fabric/epoxy composites: tensile properties by micromechanical approach
- 14 November 2017
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 27 (1) , 1-11
Hybrid silane-treated glass fabric/epoxy composites: tensile properties by micromechanical approach
- 15 May 2017
- Published by Wiley in Polymer Composites
- Vol. 39 (10) , 3383-3408
A review on aerogel: 3D nanoporous structured fillers in polymer‐based nanocomposites
There have been a number of review papers on layered silicate and carbon nanotube reinforced polymer nanocomposites, in which the fillers have high aspect ratios. Particulate‐polymer nanocomposites containing aerogel with extremely low density, large open pores, and high surface area are also an important class of polymer nanocomposites. Thus, this article provides an overview on the effect of aerogel on mechanical and thermal properties of polymer‐based nanocomposites. Moreover, the preparation, history, classification, and characteristics of the aerogel are addressed. Among the polymer‐aerogel nanocomposites, various categories including silica and carbon aerogel‐polymer nanocomposites were discussed in detail. POLYM. COMPOS., 39:3383–3408, 2018. © 2017 Society of Plastics Engineers
- 15 May 2017
- Published by Wiley in Polymer Composites
- Vol. 39 (10) , 3383-3408
A review on aerogel: 3D nanoporous structured fillers in polymer‐based nanocomposites
There have been a number of review papers on layered silicate and carbon nanotube reinforced polymer nanocomposites, in which the fillers have high aspect ratios. Particulate‐polymer nanocomposites containing aerogel with extremely low density, large open pores, and high surface area are also an important class of polymer nanocomposites. Thus, this article provides an overview on the effect of aerogel on mechanical and thermal properties of polymer‐based nanocomposites. Moreover, the preparation, history, classification, and characteristics of the aerogel are addressed. Among the polymer‐aerogel nanocomposites, various categories including silica and carbon aerogel‐polymer nanocomposites were discussed in detail. POLYM. COMPOS., 39:3383–3408, 2018. © 2017 Society of Plastics Engineers
- 23 February 2017
- Published by Wiley in Polymer Composites
- Vol. 39 (9) , 3073-3080
Influence of porosity and aspect ratio of nanoparticles on the interface modification of glass/epoxy composites
Various nanostructured particles including colloidal silica nanoparticles, mesoporous silica aerogel, silicon carbide nanoparticles, and nanowhiskers were used to modify the glass fibers surface. The influence of porosity and aspect ratio of nanoscale particles on the mechanical properties of modified glass fiber/epoxy composite samples were investigated. Fiber surfaces treated with nanoscale particles exhibited much higher coefficient of friction and roughness than unmodified fiber surfaces. Surface modified composites by silica aerogel showed the maximum increase in interfacial shear strength (IFSS) by 31%. An increase of 61% in shear punch stress was obtained by samples treated with silica aerogel and 27% for samples treated with silica nanoparticles. Improvement of 23% and 63% in tensile and flexural strength of composite samples treated with 0.5 wt% of SiC nanowhiskers and 7% and 18% for samples treated with the same content of SiC nanoparticles were observed. POLYM. COMPOS., 39:3073–3080, 2018. © 2017 Society of Plastics Engineers
- 23 February 2017
- Published by Wiley in Polymer Composites
- Vol. 39 (9) , 3073-3080
Influence of porosity and aspect ratio of nanoparticles on the interface modification of glass/epoxy composites
Various nanostructured particles including colloidal silica nanoparticles, mesoporous silica aerogel, silicon carbide nanoparticles, and nanowhiskers were used to modify the glass fibers surface. The influence of porosity and aspect ratio of nanoscale particles on the mechanical properties of modified glass fiber/epoxy composite samples were investigated. Fiber surfaces treated with nanoscale particles exhibited much higher coefficient of friction and roughness than unmodified fiber surfaces. Surface modified composites by silica aerogel showed the maximum increase in interfacial shear strength (IFSS) by 31%. An increase of 61% in shear punch stress was obtained by samples treated with silica aerogel and 27% for samples treated with silica nanoparticles. Improvement of 23% and 63% in tensile and flexural strength of composite samples treated with 0.5 wt% of SiC nanowhiskers and 7% and 18% for samples treated with the same content of SiC nanoparticles were observed. POLYM. COMPOS., 39:3073–3080, 2018. © 2017 Society of Plastics Engineers