Abolghasem Alighardashi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Abolghasem Alighardashi has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Amir Mohammad Ramezanianpour
University of Tehran
2 shared publicationsAli Torabian
A Faculty of Environment , University of Tehran , Tehran , Iran
1 shared publicationAmir Fouladitajar
1 shared publication- Artur Mennerich
B Faculty of Civil and Environmental Engineering , Ostfalia University of Applied Sciences , Suderburg , Germany
1 shared publication Azam Sadeghasadi
1 shared publication- Danial Goodarzi
Department of Civil, Water and Environmental Engineering, Shahid Beheshti University, Tehran, Iran
1 shared publication
Latest Publications
- 20 July 2021
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 41 (1) , e13715
Optimization of a three‐dimensional electrochemical process with granular activated carbon for diclofenac removal using response surface methodology
In this study, a three‐dimensional electrochemical process with aluminum electrodes in the presence of granular activated carbon derived from walnut shell (WGAC) was employed to remove Diclofenac from synthetic water. Optimum operating conditions were determined using response surface methodology, also, an empirical relationship was established between response and independent variables (activated carbon amount, contact time, pH, and electrolyte concentration). The results showed that activated carbon amount and NaCl concentration were the most influential factors on the removal efficiency, and the most significant factor affecting electrical energy was NaCl concentration. Additionally, three‐dimensional electrochemical process with granular activated carbon has the potential to work in the pH range from 1 to 9. The optimal conditions to gain maximum removal efficiency and minimum electrical energy were determined to be 4.36 g granular activated carbon, 40 min contact time, and 4390 ppm of NaCl. In addition, to show the physical characteristics of activated carbon, the field emission scanning electron microscopy and BET analysis were applied, and Spectrophotometric technique was used to determine diclofenac concentration. Considering high removal efficiency and low electrical energy consumption, the three‐dimensional electrochemical process with WGAC can be considered a cost‐effective and practicable method to remove diclofenac from water and wastewater.
- 20 July 2021
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 41 (1) , e13715
Optimization of a three‐dimensional electrochemical process with granular activated carbon for diclofenac removal using response surface methodology
In this study, a three‐dimensional electrochemical process with aluminum electrodes in the presence of granular activated carbon derived from walnut shell (WGAC) was employed to remove Diclofenac from synthetic water. Optimum operating conditions were determined using response surface methodology, also, an empirical relationship was established between response and independent variables (activated carbon amount, contact time, pH, and electrolyte concentration). The results showed that activated carbon amount and NaCl concentration were the most influential factors on the removal efficiency, and the most significant factor affecting electrical energy was NaCl concentration. Additionally, three‐dimensional electrochemical process with granular activated carbon has the potential to work in the pH range from 1 to 9. The optimal conditions to gain maximum removal efficiency and minimum electrical energy were determined to be 4.36 g granular activated carbon, 40 min contact time, and 4390 ppm of NaCl. In addition, to show the physical characteristics of activated carbon, the field emission scanning electron microscopy and BET analysis were applied, and Spectrophotometric technique was used to determine diclofenac concentration. Considering high removal efficiency and low electrical energy consumption, the three‐dimensional electrochemical process with WGAC can be considered a cost‐effective and practicable method to remove diclofenac from water and wastewater.
- 1 October 2019
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 7 (5)
CFD modeling and simulation of concentration polarization reduction by gas sparging cross-flow nanofiltration
- 1 October 2019
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 7 (5)
CFD modeling and simulation of concentration polarization reduction by gas sparging cross-flow nanofiltration
- 2 April 2019
- Published by Wiley in Water and Environment Journal
- Vol. 34 (3) , 432-440
Simulation of depth and wind effects on the hydraulic efficiency of sedimentation tanks
In this research, we aim to investigate the effects of the depth and wind effect on the surface of water on the hydraulic efficiency of the sedimentation tanks in water and wastewater treatments plants. A verified two‐dimensional numerical study was performed to evaluate hydraulic performance of series settling tanks by four different depths of 2.5, 3, 3.5 and 4 (m). Wind velocities of 5 and 7 (m/s) in co‐current and counter‐current direction of water flow in sedimentation tank were applied on the surface of the water. In this study, k–ε turbulent model and passive scalar tracer were used to perform the simulations. The research confirms that wind influence on the surface of water causes recirculation zones and increases the length of recirculation zones. In both windy and normal situation, the Real Hydraulic Retention Time and the effective volume of sedimentation tanks increases widely as the depth of the tank.
- 2 April 2019
- Published by Wiley in Water and Environment Journal
- Vol. 34 (3) , 432-440
Simulation of depth and wind effects on the hydraulic efficiency of sedimentation tanks
In this research, we aim to investigate the effects of the depth and wind effect on the surface of water on the hydraulic efficiency of the sedimentation tanks in water and wastewater treatments plants. A verified two‐dimensional numerical study was performed to evaluate hydraulic performance of series settling tanks by four different depths of 2.5, 3, 3.5 and 4 (m). Wind velocities of 5 and 7 (m/s) in co‐current and counter‐current direction of water flow in sedimentation tank were applied on the surface of the water. In this study, k–ε turbulent model and passive scalar tracer were used to perform the simulations. The research confirms that wind influence on the surface of water causes recirculation zones and increases the length of recirculation zones. In both windy and normal situation, the Real Hydraulic Retention Time and the effective volume of sedimentation tanks increases widely as the depth of the tank.
- 1 November 2018
- Published by Elsevier in Environmental Technology & Innovation
- Vol. 12, 148-159
Fixed-bed column and batch reactors performance in removal of diazinon pesticide from aqueous solutions by using walnut shell-modified activated carbon
- 1 November 2018
- Published by Elsevier in Environmental Technology & Innovation
- Vol. 12, 148-159
Fixed-bed column and batch reactors performance in removal of diazinon pesticide from aqueous solutions by using walnut shell-modified activated carbon
- 6 October 2018
- Published by Springer Nature in Asian Journal of Civil Engineering
- Vol. 20 (1) , 49-56
Material design and characterization of pervious concrete reactive barrier containing nano-silica and fine pumice aggregate
- 6 October 2018
- Published by Springer Nature in Asian Journal of Civil Engineering
- Vol. 20 (1) , 49-56
Material design and characterization of pervious concrete reactive barrier containing nano-silica and fine pumice aggregate
- 22 August 2018
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 25 (29) , 29481-29492
Pervious concrete reactive barrier containing nano-silica for nitrate removal from contaminated water
In this research, the effectiveness of using pervious concrete as a reactive barrier to decrease the concentration of nitrates in polluted water was investigated. Parameters of concrete mix design including water to cement ratio (W/C), aggregate to cement ratio (A/C), the amount of nano-silica (NS), and fine aggregates (FA) were studied based on Taguchi method. Properties of concrete such as compressive strength, density, permeability, and porosity, as well as pH measurement and the column method were carried out to assess the nitrate removal capacity of pervious concrete. Also, SEM-EDX, XRD, and FTIR were used to analyze the results. It was found that the optimum mix design in terms of nitrate removal corresponded to the mix with W/C = 0.26, A/C = 5, NS = 6%, and FA = 20%. Based on the results, it can be said that adding NS (up to 6%) and FA (up to 20%) to pervious concrete had the best influence on nitrate removal and compressive strength. Addition of NS increased the nitrate removal capacity due to increase in surface positive charges and provision of new surface functional groups.
- 22 August 2018
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 25 (29) , 29481-29492
Pervious concrete reactive barrier containing nano-silica for nitrate removal from contaminated water
In this research, the effectiveness of using pervious concrete as a reactive barrier to decrease the concentration of nitrates in polluted water was investigated. Parameters of concrete mix design including water to cement ratio (W/C), aggregate to cement ratio (A/C), the amount of nano-silica (NS), and fine aggregates (FA) were studied based on Taguchi method. Properties of concrete such as compressive strength, density, permeability, and porosity, as well as pH measurement and the column method were carried out to assess the nitrate removal capacity of pervious concrete. Also, SEM-EDX, XRD, and FTIR were used to analyze the results. It was found that the optimum mix design in terms of nitrate removal corresponded to the mix with W/C = 0.26, A/C = 5, NS = 6%, and FA = 20%. Based on the results, it can be said that adding NS (up to 6%) and FA (up to 20%) to pervious concrete had the best influence on nitrate removal and compressive strength. Addition of NS increased the nitrate removal capacity due to increase in surface positive charges and provision of new surface functional groups.
- 23 May 2018
- Published by Springer Nature in International Journal of Environmental Research
- Vol. 12 (4) , 451-458
Improvement of Carbamazepine Degradation by a Three-Dimensional Electrochemical (3-EC) Process
- 23 May 2018
- Published by Springer Nature in International Journal of Environmental Research
- Vol. 12 (4) , 451-458
Improvement of Carbamazepine Degradation by a Three-Dimensional Electrochemical (3-EC) Process
- 18 April 2017
- Published by Taylor & Francis in Environmental Technology
- Vol. 39 (8) , 1017-1024
Improving biogas production from continuous co-digestion of oily wastewater and waste-activated sludge by hydrodynamic cavitation pre-treatment
Hydrodynamic cavitation (HC) was evaluated as a pretreatment for synthetic oily wastewater (OWW) to be co-digested with waste-activated sludge (WAS). The main objective of the present research was the enhancement of biogas production by the application of HC pretreatment. HC was applied to the OWW, and the OWW and WAS were added to a 50 L continuous digestion reactor. As a control system, an identical digestion reactor was set up for co-digestion of the WAS and the OWW without pretreatment. The reactors were initially filled with inoculum and the hydraulic retention time (HRT) was set to 22 d. The HRT was gradually reduced to 19, 16, and finally 13 d, but the substrate quality was kept constant. The loading rate, accordingly, increased from 0.86 to 1.46 g TVS/(L d). The biogas volume was recorded online and its quality was analyzed regularly. The HC improved biogas production up to 43% at 22 d of HRT. Reducing the HRT decreased biogas production from the main reactor while that of the control reactor was more or less constant. HC also increased the biogas methane content; the methane concentration of the main reactor was about 3% higher than the methane concentration of the control reactor. The main reactor experienced no clogging or accumulation of fatty materials.
- 18 April 2017
- Published by Taylor & Francis in Environmental Technology
- Vol. 39 (8) , 1017-1024
Improving biogas production from continuous co-digestion of oily wastewater and waste-activated sludge by hydrodynamic cavitation pre-treatment
Hydrodynamic cavitation (HC) was evaluated as a pretreatment for synthetic oily wastewater (OWW) to be co-digested with waste-activated sludge (WAS). The main objective of the present research was the enhancement of biogas production by the application of HC pretreatment. HC was applied to the OWW, and the OWW and WAS were added to a 50 L continuous digestion reactor. As a control system, an identical digestion reactor was set up for co-digestion of the WAS and the OWW without pretreatment. The reactors were initially filled with inoculum and the hydraulic retention time (HRT) was set to 22 d. The HRT was gradually reduced to 19, 16, and finally 13 d, but the substrate quality was kept constant. The loading rate, accordingly, increased from 0.86 to 1.46 g TVS/(L d). The biogas volume was recorded online and its quality was analyzed regularly. The HC improved biogas production up to 43% at 22 d of HRT. Reducing the HRT decreased biogas production from the main reactor while that of the control reactor was more or less constant. HC also increased the biogas methane content; the methane concentration of the main reactor was about 3% higher than the methane concentration of the control reactor. The main reactor experienced no clogging or accumulation of fatty materials.
- 1 December 2016
- Published by IWA Publishing in Water Practice & Technology
- Vol. 11 (4) , 784-795
Removal of nitrate from synthetic aqueous solution and groundwater in a continuous pilot system using chemical activated carbon derived from walnut shell
Excessive nitrate in the water impose a danger to human health and contribute to eutrophication. The present continuous fixed bed pilot study was carried out using granular activated carbon made from walnut shell for removal of nitrate from aqueous solution and natural groundwater. The carbon was characterized using SEM, FTIR and BET. The BET specific surface area and average pore size before nitrate adsorption were 1434.6 m2g−1 and 2.08 nm, respectively, and after were 633.28 m2g−1 and 2.04 nm, respectively. Optimum removal of nitrate was achieved at a contact time of 2 min, pH of 6.5 and a nitrate concentration of 200 mg/l. The hydraulic loading rate was calculated to be 10 m3/h.m2 and the maximum adsorption capacity using the Langmuir adsorption isotherm model (R2 = 0.99) was 10 mg NO3/g. These experiments were also carried out using groundwater and the removal of nitrate decreased from 68% to 60% because of competition with other cations and anions.
- 1 December 2016
- Published by IWA Publishing in Water Practice & Technology
- Vol. 11 (4) , 784-795
Removal of nitrate from synthetic aqueous solution and groundwater in a continuous pilot system using chemical activated carbon derived from walnut shell
Excessive nitrate in the water impose a danger to human health and contribute to eutrophication. The present continuous fixed bed pilot study was carried out using granular activated carbon made from walnut shell for removal of nitrate from aqueous solution and natural groundwater. The carbon was characterized using SEM, FTIR and BET. The BET specific surface area and average pore size before nitrate adsorption were 1434.6 m2g−1 and 2.08 nm, respectively, and after were 633.28 m2g−1 and 2.04 nm, respectively. Optimum removal of nitrate was achieved at a contact time of 2 min, pH of 6.5 and a nitrate concentration of 200 mg/l. The hydraulic loading rate was calculated to be 10 m3/h.m2 and the maximum adsorption capacity using the Langmuir adsorption isotherm model (R2 = 0.99) was 10 mg NO3/g. These experiments were also carried out using groundwater and the removal of nitrate decreased from 68% to 60% because of competition with other cations and anions.
- 11 October 2016
- Published by Springer Nature in Paddy and Water Environment
- Vol. 15 (2) , 371-380
Risk assessment of pesticides in paddy fields and the Safīdrūd River in Gīlān, Iran
- 11 October 2016
- Published by Springer Nature in Paddy and Water Environment
- Vol. 15 (2) , 371-380
Risk assessment of pesticides in paddy fields and the Safīdrūd River in Gīlān, Iran