Joseph D. Eifert
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Joseph D. Eifert has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
- Laura Kathryn Strawn
Department of Food Science and Technology, Virginia Tech, Blacksburg, VA 24061, USA
4 shared publications - Renee R. Boyer
Virginia Tech
4 shared publications Peter W. Bodnaruk
Tyson Foods, Inc. Chicago Illinois
3 shared publicationsRobert C. Williams
Department of Food Science and Technology Virginia Tech Blacksburg Virginia
3 shared publications- Anibal Concha-Meyer
Instituto de Ciencia y Tecnología de los Alimentos, Facultad de Ciencias Agrarias y Alimentarias, Universidad Austral de Chile, Campus Isla Teja s/n, Valdivia 5090000, Chile
2 shared publications - Gregory E. Welbaum
School of Plant and Environmental Sciences, Virginia Tech, Blacksburg, VA 24060, USA
2 shared publications
Latest Publications
- Open Access
- 11 September 2026
- Published by Qeios Ltd
Review of: "Food-Contact-Surface and Product-Test 𝘓𝘪𝘴𝘵𝘦𝘳𝘪𝘢 𝘮𝘰𝘯𝘰𝘤𝘺𝘵𝘰𝘨𝘦𝘯𝘦𝘴 Positivity in U.S. Ready-to-Eat Meat and Poultry Establishments: Concurrent, Cumulative, and Temporally Separated Associations in USDA-FSIS Sampling Data, 2015-2025"
The article provides a useful analysis of USDA-FSIS test results that demonstrate some relationships between food contact surface test results and product test results. This will always be a difficult area to show correlations because environmental...
- 11 September 2026
- Published by Qeios Ltd
Open AccessReview of: "Food-Contact-Surface and Product-Test 𝘓𝘪𝘴𝘵𝘦𝘳𝘪𝘢 𝘮𝘰𝘯𝘰𝘤𝘺𝘵𝘰𝘨𝘦𝘯𝘦𝘴 Positivity in U.S. Ready-to-Eat Meat and Poultry Establishments: Concurrent, Cumulative, and Temporally Separated Associations in USDA-FSIS Sampling Data, 2015-2025"
The article provides a useful analysis of USDA-FSIS test results that demonstrate some relationships between food contact surface test results and product test results. This will always be a difficult area to show correlations because environmental...
- Open Access
- 15 April 2026
- Published by Wiley in Veterinary Medicine and Science
- Vol. 12 (3) , e70941
Trends in Veterinary Drug Residues in US Cattle: Analysing USDA Sampling Data
Introduction: Cattle production is the leading agricultural industry in the United States, accounting for the largest portion of total cash receipts for agricultural commodities. The administration of veterinary drugs in food‐producing animals can lead to the presence of drug residues in food products. Methods: The primary purpose of this study is to evaluate US national residue monitoring data to identify the most frequently detected veterinary drugs across various cattle types including dairy cows, beef cows, calves, heifers, and other types. Veterinary drug residue sampling reports and datasets for the years 2021, 2022, and 2023 were evaluated using descriptive statistical analysis to rank the most frequently detected drug residues in cattle. Results: A total of 3391 positive veterinary drug residue samples (including both violative and non‐violative residues) were detected across all food animal species for the years 2021, 2022, and 2023 with cattle samples having the majority of positive detections (3107 samples; 92%). Across all three years, dairy cows accounted for the highest number of residue detections (1264), including both violative and non‐violative detections, compared with other cattle types, beef cows (505), bob veal (449), steers (384), and heifers (263). A Pearson's Chi‐squared test indicated that the distribution of residue detections varied among cattle types (χ 2 = 390.73, df = 11, p ‐value < 0.0001). Among the violative residues, desfuroylceftiofur was the most frequently detected analyte (351 detections), followed by penicillin (161), flunixin (122), sulfadimethoxine (94), and sulfamethazine (79). Conclusion: This study highlights consistent patterns in veterinary drug residue detections in cattle from 2021 to 2023 revealing major issues in residue control and compliance. These findings underscore the importance of addressing the persistent presence of certain veterinary drugs in cattle products, support the continued role of targeted residue monitoring programs, and inform future evaluations of drug use and surveillance priorities.
- 15 April 2026
- Published by Wiley in Veterinary Medicine and Science
- Vol. 12 (3) , e70941
Open AccessTrends in Veterinary Drug Residues in US Cattle: Analysing USDA Sampling Data
Introduction: Cattle production is the leading agricultural industry in the United States, accounting for the largest portion of total cash receipts for agricultural commodities. The administration of veterinary drugs in food‐producing animals can lead to the presence of drug residues in food products. Methods: The primary purpose of this study is to evaluate US national residue monitoring data to identify the most frequently detected veterinary drugs across various cattle types including dairy cows, beef cows, calves, heifers, and other types. Veterinary drug residue sampling reports and datasets for the years 2021, 2022, and 2023 were evaluated using descriptive statistical analysis to rank the most frequently detected drug residues in cattle. Results: A total of 3391 positive veterinary drug residue samples (including both violative and non‐violative residues) were detected across all food animal species for the years 2021, 2022, and 2023 with cattle samples having the majority of positive detections (3107 samples; 92%). Across all three years, dairy cows accounted for the highest number of residue detections (1264), including both violative and non‐violative detections, compared with other cattle types, beef cows (505), bob veal (449), steers (384), and heifers (263). A Pearson's Chi‐squared test indicated that the distribution of residue detections varied among cattle types (χ 2 = 390.73, df = 11, p ‐value < 0.0001). Among the violative residues, desfuroylceftiofur was the most frequently detected analyte (351 detections), followed by penicillin (161), flunixin (122), sulfadimethoxine (94), and sulfamethazine (79). Conclusion: This study highlights consistent patterns in veterinary drug residue detections in cattle from 2021 to 2023 revealing major issues in residue control and compliance. These findings underscore the importance of addressing the persistent presence of certain veterinary drugs in cattle products, support the continued role of targeted residue monitoring programs, and inform future evaluations of drug use and surveillance priorities.
- Open Access
- 7 January 2026
- Published by Wiley in Journal of Food Science
- Vol. 91 (1) , e70822
Microbial Contamination Risks From Adjacent and Nearby Land: Evidence and Implications for Produce Safety
Consumers’ demand for fresh produce is rising due to dietary preferences and public health campaigns. Fresh produce is often consumed raw or minimally processed to retain nutrient content. If contaminated, fresh produce can become a vehicle for pathogen transmission and potentially cause outbreaks. Contamination may occur within the farm border, but some evidence suggests different sources on adjacent and nearby land may be off‐farm contributors. Natural ecosystems (e.g., wildlife habitats, vegetation), agricultural activities (e.g., livestock operations, manure and compost application, wastewater discharge), residential and industrial activities (e.g., septic systems, waste discharge), and recreational uses (e.g., parks, campgrounds, golf courses) all represent potential contamination sources. Environmental pathogens from adjacent land can reach produce farms through diverse pathways influenced by meteorological drivers (e.g., rainfall, wind) or by human activities, equipment, and animal intrusion. These adjacent land inputs interact with each other and farming practices, creating complex contamination mechanisms. This paper explored microbial contamination sources from adjacent and nearby land and proposed a risk ranking model with implications for produce safety. It aimed to provide an overall understanding of the interaction between environmental and adjacent land sources as a basis for future risk assessment and management research.
- 7 January 2026
- Published by Wiley in Journal of Food Science
- Vol. 91 (1) , e70822
Open AccessMicrobial Contamination Risks From Adjacent and Nearby Land: Evidence and Implications for Produce Safety
Consumers’ demand for fresh produce is rising due to dietary preferences and public health campaigns. Fresh produce is often consumed raw or minimally processed to retain nutrient content. If contaminated, fresh produce can become a vehicle for pathogen transmission and potentially cause outbreaks. Contamination may occur within the farm border, but some evidence suggests different sources on adjacent and nearby land may be off‐farm contributors. Natural ecosystems (e.g., wildlife habitats, vegetation), agricultural activities (e.g., livestock operations, manure and compost application, wastewater discharge), residential and industrial activities (e.g., septic systems, waste discharge), and recreational uses (e.g., parks, campgrounds, golf courses) all represent potential contamination sources. Environmental pathogens from adjacent land can reach produce farms through diverse pathways influenced by meteorological drivers (e.g., rainfall, wind) or by human activities, equipment, and animal intrusion. These adjacent land inputs interact with each other and farming practices, creating complex contamination mechanisms. This paper explored microbial contamination sources from adjacent and nearby land and proposed a risk ranking model with implications for produce safety. It aimed to provide an overall understanding of the interaction between environmental and adjacent land sources as a basis for future risk assessment and management research.
- Open Access
- 12 December 2024
- Published by Wiley in Journal of Food Safety
- Vol. 44 (6)
Recovery and Survival of Aerosolized Escherichia coli and Enterococcus faecium on Food‐Grade Rubber, HDPE Plastic, Stainless Steel, and Waxed Cardboard
Contamination of food contact surfaces by airborne transmission of pathogens from the environment has contributed to disease outbreaks. Therefore, this study evaluated the survival and recovery of aerosolized generic Escherichia coli and Enterococcus faecium from four food contact surfaces (food‐grade silicone rubber, high‐density polyethylene [HDPE] plastic, stainless steel, and waxed cardboard), after four contact times (10, 20, 40, and 60 min), two relative humidity (RH) levels (high: 80%–90%, low: 40%–50%), three distances from aerosolization source (0, 36.5, and 73 cm; E. coli only), and with and without airflow (E. coli only). ANOVA test with Tukey's HSD at α = 0.05 was used to determine how treatment combinations influenced recovery. At high humidity, E. coli recovery on all materials after 40 min was ~1.0 log lower than recovery after 10 min, and further reduced by 1.0 log at 60 min. At lower humidity, E. coli recovery on all materials was ~1.0 log lower at 10 and 20 min compared with high humidity. Distances exerted no significance, whereas airflow presence lowered E. coli recovery. E. coli survival on all materials declined from ~5.0 log CFU/coupon at 0 h to 3.5 log CFU/coupon at 6 h, and 2.0 log CFU/coupon at 24 h post‐inoculation. E. coli recovery was significantly lower (p < 0.05) on waxed cardboard. Low RH and longer contact time reduced E. coli recovery but not E. faecium. E. faecium recovery was consistent across treatment combinations, with changes < 0.5 log CFU/coupon. The findings are relevant for the survival of bacteria on common food contact surfaces and the potential of transmission to food products.
- 12 December 2024
- Published by Wiley in Journal of Food Safety
- Vol. 44 (6)
Open AccessRecovery and Survival of Aerosolized Escherichia coli and Enterococcus faecium on Food‐Grade Rubber, HDPE Plastic, Stainless Steel, and Waxed Cardboard
Contamination of food contact surfaces by airborne transmission of pathogens from the environment has contributed to disease outbreaks. Therefore, this study evaluated the survival and recovery of aerosolized generic Escherichia coli and Enterococcus faecium from four food contact surfaces (food‐grade silicone rubber, high‐density polyethylene [HDPE] plastic, stainless steel, and waxed cardboard), after four contact times (10, 20, 40, and 60 min), two relative humidity (RH) levels (high: 80%–90%, low: 40%–50%), three distances from aerosolization source (0, 36.5, and 73 cm; E. coli only), and with and without airflow (E. coli only). ANOVA test with Tukey's HSD at α = 0.05 was used to determine how treatment combinations influenced recovery. At high humidity, E. coli recovery on all materials after 40 min was ~1.0 log lower than recovery after 10 min, and further reduced by 1.0 log at 60 min. At lower humidity, E. coli recovery on all materials was ~1.0 log lower at 10 and 20 min compared with high humidity. Distances exerted no significance, whereas airflow presence lowered E. coli recovery. E. coli survival on all materials declined from ~5.0 log CFU/coupon at 0 h to 3.5 log CFU/coupon at 6 h, and 2.0 log CFU/coupon at 24 h post‐inoculation. E. coli recovery was significantly lower (p < 0.05) on waxed cardboard. Low RH and longer contact time reduced E. coli recovery but not E. faecium. E. faecium recovery was consistent across treatment combinations, with changes < 0.5 log CFU/coupon. The findings are relevant for the survival of bacteria on common food contact surfaces and the potential of transmission to food products.
- 3 April 2023
- Published by Oxford University Press (OUP) in Letters in Applied Microbiology
- Vol. 76 (4) , 1-6
Delmopinol hydrochloride inhibitsCampylobacter jejunion skinless poultry meat, stainless steel, and high-density polyethylene food contact surfaces
Delmopinol hydrochloride (delmopinol) is a cationic surfactant that is effective for treating and preventing gingivitis and periodontitis. This study evaluated the effectiveness of delmopinol for reducing attachment of Campylobacter jejuni to chicken meat, stainless steel and high-density polyethylene (HDPE). These test materials were spot-inoculated with a C. jejuni culture. After 10 min, samples were sprayed with 0.5% or 1.0% delmopinol, 0.01% sodium hypochlorite, or distilled water. After a 1, 10, or 20 min contact time, samples were rinsed which were serially diluted onto Campy-Cefex Agar. For additional samples, solutions were applied before inoculation with C. jejuni. Cultures remained undisturbed for 1, 10, or 20 min. Samples were then rinsed and plated as above. When C. jejuni was inoculated before treatments, 1% delmopinol application led to mean log reductions of 1.26, 3.70, and 3.72 log cfu ml−1, greater than distilled water alone, for chicken, steel and HDPE respectively. When C. jejuni was inoculated after spray treatments, 1% delmopinol reduced C. jejuni by 2.72, 3.20, and 3.99 mean log cfu ml−1 more than distilled water for chicken, steel and HDPE respectively. Application of 1% delmopinol, resulted in a significantly (P < 0.05) greater log reduction than a 0.01% sodium hypochlorite or distilled water application.
- 3 April 2023
- Published by Oxford University Press (OUP) in Letters in Applied Microbiology
- Vol. 76 (4) , 1-6
Delmopinol hydrochloride inhibitsCampylobacter jejunion skinless poultry meat, stainless steel, and high-density polyethylene food contact surfaces
Delmopinol hydrochloride (delmopinol) is a cationic surfactant that is effective for treating and preventing gingivitis and periodontitis. This study evaluated the effectiveness of delmopinol for reducing attachment of Campylobacter jejuni to chicken meat, stainless steel and high-density polyethylene (HDPE). These test materials were spot-inoculated with a C. jejuni culture. After 10 min, samples were sprayed with 0.5% or 1.0% delmopinol, 0.01% sodium hypochlorite, or distilled water. After a 1, 10, or 20 min contact time, samples were rinsed which were serially diluted onto Campy-Cefex Agar. For additional samples, solutions were applied before inoculation with C. jejuni. Cultures remained undisturbed for 1, 10, or 20 min. Samples were then rinsed and plated as above. When C. jejuni was inoculated before treatments, 1% delmopinol application led to mean log reductions of 1.26, 3.70, and 3.72 log cfu ml−1, greater than distilled water alone, for chicken, steel and HDPE respectively. When C. jejuni was inoculated after spray treatments, 1% delmopinol reduced C. jejuni by 2.72, 3.20, and 3.99 mean log cfu ml−1 more than distilled water for chicken, steel and HDPE respectively. Application of 1% delmopinol, resulted in a significantly (P < 0.05) greater log reduction than a 0.01% sodium hypochlorite or distilled water application.
- Open Access
Microbubbles Remove Listeria monocytogenes from the Surface of Stainless Steel, Cucumber, and Avocado
Fresh produce may be contaminated by bacterial pathogens, including Listeria monocytogenes, during harvesting, packaging, or transporting. A low-intensity cavitation process with air being injected into water was studied to determine the microbubbles’ efficiency when detaching L. monocytogenes from stainless steel and the surface of fresh cucumber and avocado. Stainless steel coupons (1″ × 2″), cucumber, and avocado surfaces were inoculated with L. monocytogenes (LCDC strain). After 1, 24 or 48 h, loosely attached cells were washed off, and inoculated areas were targeted by microbubbles (~0.1–0.5 mm dia.) through a bubble diffuser (1.0 L air/min) for 1, 2, 5, or 10 min. For steel, L. monocytogenes (48 h drying) detachment peaked at 2.95 mean log reduction after 10 min of microbubbles when compared to a no-bubble treatment. After 48 h pathogen drying, cucumbers treated for 10 min showed a 1.78 mean log reduction of L. monocytogenes. For avocados, L. monocytogenes (24 h drying) detachment peaked at 1.65 log reduction after 10 min of microbubbles. Microbubble applications may be an effective, economical, and environmentally friendly way to remove L. monocytogenes, and possibly other bacterial pathogens, from food contact surfaces and the surfaces of whole, intact fresh produce.
Open AccessMicrobubbles Remove Listeria monocytogenes from the Surface of Stainless Steel, Cucumber, and Avocado
Fresh produce may be contaminated by bacterial pathogens, including Listeria monocytogenes, during harvesting, packaging, or transporting. A low-intensity cavitation process with air being injected into water was studied to determine the microbubbles’ efficiency when detaching L. monocytogenes from stainless steel and the surface of fresh cucumber and avocado. Stainless steel coupons (1″ × 2″), cucumber, and avocado surfaces were inoculated with L. monocytogenes (LCDC strain). After 1, 24 or 48 h, loosely attached cells were washed off, and inoculated areas were targeted by microbubbles (~0.1–0.5 mm dia.) through a bubble diffuser (1.0 L air/min) for 1, 2, 5, or 10 min. For steel, L. monocytogenes (48 h drying) detachment peaked at 2.95 mean log reduction after 10 min of microbubbles when compared to a no-bubble treatment. After 48 h pathogen drying, cucumbers treated for 10 min showed a 1.78 mean log reduction of L. monocytogenes. For avocados, L. monocytogenes (24 h drying) detachment peaked at 1.65 log reduction after 10 min of microbubbles. Microbubble applications may be an effective, economical, and environmentally friendly way to remove L. monocytogenes, and possibly other bacterial pathogens, from food contact surfaces and the surfaces of whole, intact fresh produce.
- 30 November 2020
- Published by Wiley in Journal of Food Safety
- Vol. 43 (2)
Practical application of bacteriophage in food manufacturing facilities for the control of Listeria sp.
Listeria monocytogenes is a foodborne pathogen with the ability to persist and form biofilm matrices in processing environments of food manufacturing facilities. Bacteriophages are bacterial viruses with host specific lethality. Published research on the application of phage to control Listeria sp. in manufacturing environments is limited. In this study, we have assessed the capacity of bacteriophage P100 (Listex™) to reduce incidence of Listeria sp. in the ready‐to‐eat (RTE) environment of refrigerated (4°C) and ambient (20°C) temperature facilities using two different application strategies. A moderate application applied as a single treatment every 24 hr over three days (2 × 107 PFU/ml) and an intensified application applied once every 6 hr over a 24 hr period (1 × 108 PFU/ml). Environmental nonfood contact surface (NFCS) samples were collected and analyzed for the presence of Listeria sp. before and after treatment. When the moderate treatment protocol was applied the incidence of positives decreased from 51.3 to 17.5% in the 4°C environment and from 67.5 to 23.1% in the 20°C production area. For the intensified phage treatment method, the initial positive rate in the 4°C environment ranged from 5 to 47.5%, with an overall 43% reduction in Listeria sp. In the 20°C facility, initial environmental Listeria sp. ranged from 15 to 50%, with an overall reduction of 32% after treatment with phage P100. Data indicate the application of Listeria specific phage P100 in RTE food production environments by either the moderate or intensified application method can reduce incidence and be considered an additional intervention strategy for controlling this pathogen on NFCS.
- 30 November 2020
- Published by Wiley in Journal of Food Safety
- Vol. 43 (2)
Practical application of bacteriophage in food manufacturing facilities for the control of Listeria sp.
Listeria monocytogenes is a foodborne pathogen with the ability to persist and form biofilm matrices in processing environments of food manufacturing facilities. Bacteriophages are bacterial viruses with host specific lethality. Published research on the application of phage to control Listeria sp. in manufacturing environments is limited. In this study, we have assessed the capacity of bacteriophage P100 (Listex™) to reduce incidence of Listeria sp. in the ready‐to‐eat (RTE) environment of refrigerated (4°C) and ambient (20°C) temperature facilities using two different application strategies. A moderate application applied as a single treatment every 24 hr over three days (2 × 107 PFU/ml) and an intensified application applied once every 6 hr over a 24 hr period (1 × 108 PFU/ml). Environmental nonfood contact surface (NFCS) samples were collected and analyzed for the presence of Listeria sp. before and after treatment. When the moderate treatment protocol was applied the incidence of positives decreased from 51.3 to 17.5% in the 4°C environment and from 67.5 to 23.1% in the 20°C production area. For the intensified phage treatment method, the initial positive rate in the 4°C environment ranged from 5 to 47.5%, with an overall 43% reduction in Listeria sp. In the 20°C facility, initial environmental Listeria sp. ranged from 15 to 50%, with an overall reduction of 32% after treatment with phage P100. Data indicate the application of Listeria specific phage P100 in RTE food production environments by either the moderate or intensified application method can reduce incidence and be considered an additional intervention strategy for controlling this pathogen on NFCS.
- 11 February 2020
- Published by Wiley in Journal of Food Safety
- Vol. 40 (3)
Fate of Listeria on various food contact and noncontact surfaces when treated with bacteriophage
Study objective was to determine efficacy of a bacteriophage suspension against Listeria spp. when applied to three common types of materials used in food manufacturing facilities. Materials included two food contact materials (stainless steel and polyurethane thermoplastic belting) and one noncontact material (epoxy flooring). Coupons of each material were inoculated with a cocktail containing L. monocytogenes and L. innocua (4 to 5‐log10 CFU/cm2). Two phage concentrations and a control, 0, 2 × 107 and 1 × 108 PFU/cm2 were evaluated. Treated samples were held at 4 or 20°C for 1 and 3 hr to determine the effect of temperature and treatment time. Reductions in Listeria populations ranged from 1.27 to 3.33 log10 CFU/cm2 on stainless steel, from 1.17 to 2.76 log10 CFU/cm2 on polyurethane thermoplastic belting, and from 1.19 to 1.76 log10 CFU/cm2 on epoxy resin flooring. Higher phage concentration (1 × 108 PFU/cm2), longer treatment time (3 hr), and processing area temperature of 20°C showed a greater (p ≤ .05) reduction of Listeria on the stainless‐steel and polyurethane thermoplastic belting coupons. Overall, Listeria reduction by phage treatment occurred on all three materials tested, under all conditions.
- 11 February 2020
- Published by Wiley in Journal of Food Safety
- Vol. 40 (3)
Fate of Listeria on various food contact and noncontact surfaces when treated with bacteriophage
Study objective was to determine efficacy of a bacteriophage suspension against Listeria spp. when applied to three common types of materials used in food manufacturing facilities. Materials included two food contact materials (stainless steel and polyurethane thermoplastic belting) and one noncontact material (epoxy flooring). Coupons of each material were inoculated with a cocktail containing L. monocytogenes and L. innocua (4 to 5‐log10 CFU/cm2). Two phage concentrations and a control, 0, 2 × 107 and 1 × 108 PFU/cm2 were evaluated. Treated samples were held at 4 or 20°C for 1 and 3 hr to determine the effect of temperature and treatment time. Reductions in Listeria populations ranged from 1.27 to 3.33 log10 CFU/cm2 on stainless steel, from 1.17 to 2.76 log10 CFU/cm2 on polyurethane thermoplastic belting, and from 1.19 to 1.76 log10 CFU/cm2 on epoxy resin flooring. Higher phage concentration (1 × 108 PFU/cm2), longer treatment time (3 hr), and processing area temperature of 20°C showed a greater (p ≤ .05) reduction of Listeria on the stainless‐steel and polyurethane thermoplastic belting coupons. Overall, Listeria reduction by phage treatment occurred on all three materials tested, under all conditions.
- Open Access
- 29 April 2019
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 4 (4) , 043603
Bubble impact on a tilted wall: Removing bacteria using bubbles
Dynamics of a bubble impacting and sliding on a tilted surface has been investigated through experimental and computational methods. In experiments, bubble-wall interaction has been characterized with an air bubble of about 550 in radius and a rising speed of about 30 cm/s as it impacts a solid substrate of a wall angle between and . Specifically, shear stress generated on the wall has been calculated and compared with bacterium adhesion force in order to evaluate a potential sanitization function. We numerically solved a force balance including buoyancy, hydrodynamic inertia and drag, and lift and thin film force to determine the bubble motion. Results showed that the shear stress increases with the wall inclination. The maximum shear stress goes up to more than 300 Pa as a single bubble impacts and scrubs a tilted wall. We found that such a high shear stress is attributed to a rapid change in thin film curvature (flipping bubble-water interface) during the bouncing stage. Later, during the sliding stage, a smaller shear stress up to around 45 Pa is generated for a longer period. We also showed that the shear stress generated during the bouncing and sliding stages is high enough to remove bacteria from a surface as a potential method for removing bacteria from tilted surfaces.- 29 April 2019
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 4 (4) , 043603
Open AccessBubble impact on a tilted wall: Removing bacteria using bubbles
Dynamics of a bubble impacting and sliding on a tilted surface has been investigated through experimental and computational methods. In experiments, bubble-wall interaction has been characterized with an air bubble of about 550 in radius and a rising speed of about 30 cm/s as it impacts a solid substrate of a wall angle between and . Specifically, shear stress generated on the wall has been calculated and compared with bacterium adhesion force in order to evaluate a potential sanitization function. We numerically solved a force balance including buoyancy, hydrodynamic inertia and drag, and lift and thin film force to determine the bubble motion. Results showed that the shear stress increases with the wall inclination. The maximum shear stress goes up to more than 300 Pa as a single bubble impacts and scrubs a tilted wall. We found that such a high shear stress is attributed to a rapid change in thin film curvature (flipping bubble-water interface) during the bouncing stage. Later, during the sliding stage, a smaller shear stress up to around 45 Pa is generated for a longer period. We also showed that the shear stress generated during the bouncing and sliding stages is high enough to remove bacteria from a surface as a potential method for removing bacteria from tilted surfaces. - Open Access
- 19 September 2018
- Published by Frontiers Media SA in Frontiers in Sustainable Food Systems
- Vol. 2
Cavitation Bubbles Remove and Inactivate Listeria and Salmonella on the Surface of Fresh Roma Tomatoes and Cantaloupes
Raw produce has frequently been identified as the source of bacterial pathogens that can cause human illnesses, including listeriosis and salmonellosis. Microbial pathogens may attach and form biofilms on raw fruit surfaces and can be difficult to remove. A cavitation process (injection of bubbles into water) was studied for its effectiveness for removal and inactivation of Listeria monocytogenes and Salmonella Newport from the surfaces of fresh Roma tomatoes and cantaloupes. Individual fruit were separately inoculated with each pathogen, then submerged in a water tank and treated with a bubble flow through an air stone using one airflow rate (0–14 liters/min.) for up to 60 s. As airflow increased, L. monocytogenes reduction on tomato and cantaloupe surfaces increased up to 1.2 and 0.8 log CFU/fruit greater than with water alone (no bubbles), respectively. With a 14 L/min flow rate, Salmonella reduction on tomato and cantaloupe surfaces increased up to 0.9 and 0.7 log CFU/fruit greater than when no bubbles applied, respectively. Also, with the bubble treatments, additional pathogen reduction (detached organisms) was observed in the tank water. Therefore, these bubble streams can be used to enhance the detachment of bacteria from fruit surfaces and to inactivate a proportion of these detached microorganisms. Additionally, recoveries of Salmonella from inoculated Roma tomatoes and cantaloupe were determined for treatment water that contained 50 or 150 ppm sodium hypochlorite. Combining both cavitating bubbles and 150 ppm chlorine in the tank water resulted in greater efficacy of removing or inactivating S. Newport from the surface of cantaloupe (2.9 log CFU) than with cavitation (2.5 log CFU) or chlorine (1.9 log CFU) alone. The physical force of a bubble stream on raw produce can effectively detach and inactivate surface bacteria, and has the potential to reduce antimicrobial chemical use and water use in post-harvest packing operations.
- 19 September 2018
- Published by Frontiers Media SA in Frontiers in Sustainable Food Systems
- Vol. 2
Open AccessCavitation Bubbles Remove and Inactivate Listeria and Salmonella on the Surface of Fresh Roma Tomatoes and Cantaloupes
Raw produce has frequently been identified as the source of bacterial pathogens that can cause human illnesses, including listeriosis and salmonellosis. Microbial pathogens may attach and form biofilms on raw fruit surfaces and can be difficult to remove. A cavitation process (injection of bubbles into water) was studied for its effectiveness for removal and inactivation of Listeria monocytogenes and Salmonella Newport from the surfaces of fresh Roma tomatoes and cantaloupes. Individual fruit were separately inoculated with each pathogen, then submerged in a water tank and treated with a bubble flow through an air stone using one airflow rate (0–14 liters/min.) for up to 60 s. As airflow increased, L. monocytogenes reduction on tomato and cantaloupe surfaces increased up to 1.2 and 0.8 log CFU/fruit greater than with water alone (no bubbles), respectively. With a 14 L/min flow rate, Salmonella reduction on tomato and cantaloupe surfaces increased up to 0.9 and 0.7 log CFU/fruit greater than when no bubbles applied, respectively. Also, with the bubble treatments, additional pathogen reduction (detached organisms) was observed in the tank water. Therefore, these bubble streams can be used to enhance the detachment of bacteria from fruit surfaces and to inactivate a proportion of these detached microorganisms. Additionally, recoveries of Salmonella from inoculated Roma tomatoes and cantaloupe were determined for treatment water that contained 50 or 150 ppm sodium hypochlorite. Combining both cavitating bubbles and 150 ppm chlorine in the tank water resulted in greater efficacy of removing or inactivating S. Newport from the surface of cantaloupe (2.9 log CFU) than with cavitation (2.5 log CFU) or chlorine (1.9 log CFU) alone. The physical force of a bubble stream on raw produce can effectively detach and inactivate surface bacteria, and has the potential to reduce antimicrobial chemical use and water use in post-harvest packing operations.