Jan Setiawan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jan Setiawan has a total of 239 co-authors. Here are the top co-authors by number of shared publications:
Wisnu Ari Adi
8 shared publicationsYunasfi
8 shared publicationsDidin S. Winatapura
Research Center for Advanced Materials, National Research and Innovation Agency, Tangerang Selatan, Indonesia
6 shared publicationsYunasfi Yunasfi
Research Center for Energy Materials, National Research and Innovation Agency (BRIN), South Tangerang, Indonesia
6 shared publicationsMashadi
5 shared publicationsSlamet Pribadi
BATAN
5 shared publications
Latest Publications
- Open Access
- 28 August 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (12 (142)) , 6-24
Enhancing layered structural stability via mg doping at the Mn site to suppress irreversible oxygen redox activity in Li1.2Mn0.4–XMgXCo0.4O2 cathode materials
The object of the study is Mg-doped Li- and Mn-rich layered oxide cathode materials with the composition Li1.2Mn0.4–xMgxCo0.4O2, where x = 0, 0.02, 0.04, and 0.06. The materials were synthesized by solid-state reaction. Mg doping at the transition-metal/Mn site was carried out to improve the stability of the layered structure and suppress irreversible oxygen-redox activity during Li2MnO3 activation. All samples contained R-3m LiMO2-like and C2/m Li2MnO3-like phases, with the Li2MnO3-like phase fraction increasing from 46.014 wt. % in the undoped sample to 52.464 wt. % at x = 0.06, while the I(003)/I(104) ratio increased from 1.66 to 1.92 at x = 0.04. The undoped sample showed the highest initial charge capacity of 171.46 mAh g⁻1 and discharge capacity of 131.4 mAh g⁻1. The Mg-doped sample with x = 0.02 showed the highest discharge capacity among the doped samples, at 112.58 mAh g⁻1, and also exhibited the best Li⁺ diffusion, 1.60 × 10⁻15 cm2 s⁻1, whereas the sample with x = 0.06 showed a decrease to 4.85 × 10⁻16 cm2 s⁻1. Overall, the results show that Mg doping improved the ordering of the layered structure and suppressed irreversible oxygen activity during Li2MnO3 activation at 4.50–4.55 V. However, this suppression of the oxygen-redox process also caused the Mg-doped samples to have lower capacity than the undoped sample. The excessive Mg addition can reduce capacity and hinder Li⁺ transport. In this study, the composition x = 0.02 showed the best balance among capacity, structural stability, and Li⁺ diffusion. These results can serve as a reference for optimizing Mg content in Li- and Mn-rich layered oxide cathodes for Li-ion batteries operating at high voltage, where structural stability, oxygen-redox control, capacity, and Li⁺ transport need to be balanced
- 28 August 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (12 (142)) , 6-24
Open AccessEnhancing layered structural stability via mg doping at the Mn site to suppress irreversible oxygen redox activity in Li1.2Mn0.4–XMgXCo0.4O2 cathode materials
The object of the study is Mg-doped Li- and Mn-rich layered oxide cathode materials with the composition Li1.2Mn0.4–xMgxCo0.4O2, where x = 0, 0.02, 0.04, and 0.06. The materials were synthesized by solid-state reaction. Mg doping at the transition-metal/Mn site was carried out to improve the stability of the layered structure and suppress irreversible oxygen-redox activity during Li2MnO3 activation. All samples contained R-3m LiMO2-like and C2/m Li2MnO3-like phases, with the Li2MnO3-like phase fraction increasing from 46.014 wt. % in the undoped sample to 52.464 wt. % at x = 0.06, while the I(003)/I(104) ratio increased from 1.66 to 1.92 at x = 0.04. The undoped sample showed the highest initial charge capacity of 171.46 mAh g⁻1 and discharge capacity of 131.4 mAh g⁻1. The Mg-doped sample with x = 0.02 showed the highest discharge capacity among the doped samples, at 112.58 mAh g⁻1, and also exhibited the best Li⁺ diffusion, 1.60 × 10⁻15 cm2 s⁻1, whereas the sample with x = 0.06 showed a decrease to 4.85 × 10⁻16 cm2 s⁻1. Overall, the results show that Mg doping improved the ordering of the layered structure and suppressed irreversible oxygen activity during Li2MnO3 activation at 4.50–4.55 V. However, this suppression of the oxygen-redox process also caused the Mg-doped samples to have lower capacity than the undoped sample. The excessive Mg addition can reduce capacity and hinder Li⁺ transport. In this study, the composition x = 0.02 showed the best balance among capacity, structural stability, and Li⁺ diffusion. These results can serve as a reference for optimizing Mg content in Li- and Mn-rich layered oxide cathodes for Li-ion batteries operating at high voltage, where structural stability, oxygen-redox control, capacity, and Li⁺ transport need to be balanced
- 6 August 2026
- Published by Springer Nature in Bulletin of Materials Science
- Vol. 49 (3)
Tuning absorption bandwidth of single-phase Co–Zn–Ti ferrite via Fe3+ doping for microwave absorption
- 6 August 2026
- Published by Springer Nature in Bulletin of Materials Science
- Vol. 49 (3)
Tuning absorption bandwidth of single-phase Co–Zn–Ti ferrite via Fe3+ doping for microwave absorption
- 6 February 2026
- Published by Springer Nature in Journal of Materials Science
- Vol. 61 (10) , 6841-6855
Enhanced thermoelectric performance in Fe₂CrAl1−2xNixSnx Heusler alloys through co-doping and electronic structure optimization
- 6 February 2026
- Published by Springer Nature in Journal of Materials Science
- Vol. 61 (10) , 6841-6855
Enhanced thermoelectric performance in Fe₂CrAl1−2xNixSnx Heusler alloys through co-doping and electronic structure optimization
- 16 January 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 83
Structural and synergistic effect of SnO₂-carbon interfaces for improved lithium-ion battery anode performance
- 16 January 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 83
Structural and synergistic effect of SnO₂-carbon interfaces for improved lithium-ion battery anode performance
- Open Access
- 5 December 2025
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 8 (3) , 640-652
Synthesis and Characterization of Hybrid Teak Wood/Water Hyacinth Reinforced Polyester Composites for Eco-Friendly Motorcycle-Brake Pad Application
Non-asbestos materials are developed to replace asbestos as brake pad due to the dangers to human health. Therefore, this study aimed to explore the development of hybrid reinforced polyester composites using natural fibers such as teak wood and water hyacinth for brake pad application. Natural fibers were prepared by drying, cutting, and filtering through a 30-mesh sieve. The quantity of polyester/catalyst resin was fixed at 30 g, while teak wood and water hyacinth fibers were varied (15, 10, and 5 g). Fillers and composites were investigated using Fourier transform infrared (FTIR) and composites were further analyzed through scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), thermogravimetric analysis-differential scanning calorimetry (TGA-DSC), hardness, and wear resistance testing. The results of FTIR spectra showed that a 5TW-15WH sample had the lowest lignin content, while surface morphology of composites was inhomogeneous with few voids and cracks. Based on EDS investigation, carbon (C) and oxygen (O) were the two most abundant elements, indicating lignin, cellulose, and hemicellulose as the main components in composites. TGA measurement showed that 15TW-5WH sample had lower weight loss compared to others. Increasing water hyacinth caused a significant improvement in material performance, with 5 g teak wood-15 g water hyacinth in the composite, showing the highest hardness at 71.2 Shore D and lowest wear rate of 5.373 × 10-6 mm2/kg.
- 5 December 2025
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 8 (3) , 640-652
Open AccessSynthesis and Characterization of Hybrid Teak Wood/Water Hyacinth Reinforced Polyester Composites for Eco-Friendly Motorcycle-Brake Pad Application
Non-asbestos materials are developed to replace asbestos as brake pad due to the dangers to human health. Therefore, this study aimed to explore the development of hybrid reinforced polyester composites using natural fibers such as teak wood and water hyacinth for brake pad application. Natural fibers were prepared by drying, cutting, and filtering through a 30-mesh sieve. The quantity of polyester/catalyst resin was fixed at 30 g, while teak wood and water hyacinth fibers were varied (15, 10, and 5 g). Fillers and composites were investigated using Fourier transform infrared (FTIR) and composites were further analyzed through scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), thermogravimetric analysis-differential scanning calorimetry (TGA-DSC), hardness, and wear resistance testing. The results of FTIR spectra showed that a 5TW-15WH sample had the lowest lignin content, while surface morphology of composites was inhomogeneous with few voids and cracks. Based on EDS investigation, carbon (C) and oxygen (O) were the two most abundant elements, indicating lignin, cellulose, and hemicellulose as the main components in composites. TGA measurement showed that 15TW-5WH sample had lower weight loss compared to others. Increasing water hyacinth caused a significant improvement in material performance, with 5 g teak wood-15 g water hyacinth in the composite, showing the highest hardness at 71.2 Shore D and lowest wear rate of 5.373 × 10-6 mm2/kg.
- 17 October 2025
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 23 (1)
Synthesis of SiC–SiO 2 nanocomposites using a simple mechanical milling and their microwave absorption performance
The combination of silicon carbide (SiC) and silicon dioxide (SiO 2 ) holds significant potential for advancing modern technologies, particularly the development of microwave‐absorbing materials (MAMs) due to their unique dielectric properties. In this study, a simple and cost‐effective method has been used to synthesize SiC–SiO 2 nanocomposites from silicon and graphite powders using high‐energy milling at room temperature in air atmosphere, without any heat treatment. X‐ray diffraction, Fourier‐transform infrared spectroscopy, scanning electron microscopy with energy‐dispersive X‐ray spectroscopy, and high‐magnification transmission electron microscopy characterizations confirmed the formation of pure SiC–SiO 2 nanocomposites after milling for 20 h, with particle sizes reduced to sub‐100 nm. Vector network analyzer measurement revealed the composites’ enhancement in microwave absorption performance at a thickness of only 1.50 mm from a minimum reflection loss (RL) of ‒4.00 dB at 10.88 GHz (∼60% absorption) before milling to ‒12.15 dB at 11.50 GHz (∼93% absorption) after 20 h of milling, with further improvement to ‒13.80 dB at 11.50 GHz (∼96% absorption) after 40 h. The effective absorption bandwidth is also enhanced from 0.84 to 1.54 GHz after 20 and 40 h of milling, respectively. The enhanced microwave absorption is attributed to the nano‐size effect, interfacial polarization, and multiple internal reflection. These findings may pave the way for realizing the industrial‐scale production of SiC‐based MAMs.
- 17 October 2025
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 23 (1)
Synthesis of SiC–SiO 2 nanocomposites using a simple mechanical milling and their microwave absorption performance
The combination of silicon carbide (SiC) and silicon dioxide (SiO 2 ) holds significant potential for advancing modern technologies, particularly the development of microwave‐absorbing materials (MAMs) due to their unique dielectric properties. In this study, a simple and cost‐effective method has been used to synthesize SiC–SiO 2 nanocomposites from silicon and graphite powders using high‐energy milling at room temperature in air atmosphere, without any heat treatment. X‐ray diffraction, Fourier‐transform infrared spectroscopy, scanning electron microscopy with energy‐dispersive X‐ray spectroscopy, and high‐magnification transmission electron microscopy characterizations confirmed the formation of pure SiC–SiO 2 nanocomposites after milling for 20 h, with particle sizes reduced to sub‐100 nm. Vector network analyzer measurement revealed the composites’ enhancement in microwave absorption performance at a thickness of only 1.50 mm from a minimum reflection loss (RL) of ‒4.00 dB at 10.88 GHz (∼60% absorption) before milling to ‒12.15 dB at 11.50 GHz (∼93% absorption) after 20 h of milling, with further improvement to ‒13.80 dB at 11.50 GHz (∼96% absorption) after 40 h. The effective absorption bandwidth is also enhanced from 0.84 to 1.54 GHz after 20 and 40 h of milling, respectively. The enhanced microwave absorption is attributed to the nano‐size effect, interfacial polarization, and multiple internal reflection. These findings may pave the way for realizing the industrial‐scale production of SiC‐based MAMs.
- 13 September 2025
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 36 (9)
Degradation of Crosslinked PVC /Titanium Oxide Nanocomposites Under Gamma Irradiation
This study investigates the gamma radiation resistance of crosslinked polyvinyl chloride/titanium dioxide (XLPVC/TiO 2 ) nanocomposites (3–5 wt% TiO 2 ) for electrical cable insulation. Samples irradiated up to 700 kGy were characterized using Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy‐energy dispersive spectroscopy (SEM‐EDS), atomic force microscopes (AFMs), thermogravimetric analysis‐differential scanning calorimetry (TGA‐DSC), resistivity, density, hardness, and tensile strength measurements. Key findings include reduced particle agglomeration, decreased surface roughness with increasing radiation dose, and altered FTIR spectra post‐irradiation. The XLPVC + 3% TiO 2 composite demonstrated superior stability, maintaining consistent crystallinity (54% at 100 kGy, 47% at 400 kGy, 51% at 700 kGy) and exhibiting the highest end‐of‐life dose (479 kGy), while the 4% composite showed 512 kGy radiation tolerance. Overall, XLPVC + 3% TiO 2 exhibited optimal radiation resistance, warranting further research on combined radiation–thermal aging to elucidate degradation mechanisms.
- 13 September 2025
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 36 (9)
Degradation of Crosslinked PVC /Titanium Oxide Nanocomposites Under Gamma Irradiation
This study investigates the gamma radiation resistance of crosslinked polyvinyl chloride/titanium dioxide (XLPVC/TiO 2 ) nanocomposites (3–5 wt% TiO 2 ) for electrical cable insulation. Samples irradiated up to 700 kGy were characterized using Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy‐energy dispersive spectroscopy (SEM‐EDS), atomic force microscopes (AFMs), thermogravimetric analysis‐differential scanning calorimetry (TGA‐DSC), resistivity, density, hardness, and tensile strength measurements. Key findings include reduced particle agglomeration, decreased surface roughness with increasing radiation dose, and altered FTIR spectra post‐irradiation. The XLPVC + 3% TiO 2 composite demonstrated superior stability, maintaining consistent crystallinity (54% at 100 kGy, 47% at 400 kGy, 51% at 700 kGy) and exhibiting the highest end‐of‐life dose (479 kGy), while the 4% composite showed 512 kGy radiation tolerance. Overall, XLPVC + 3% TiO 2 exhibited optimal radiation resistance, warranting further research on combined radiation–thermal aging to elucidate degradation mechanisms.
- 28 August 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (12) , 11626-11639
The High Dielectric Loss Tangent of Zinc-Doped Cobalt Titanate and Its Correlation with Microwave Absorption Performance in the S-Band Frequency
- 28 August 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (12) , 11626-11639
The High Dielectric Loss Tangent of Zinc-Doped Cobalt Titanate and Its Correlation with Microwave Absorption Performance in the S-Band Frequency
- 25 July 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (2)
The Addition of Yttrium Ions Doping to Increase the Stability of Particle Size and its Effect on the Magnetic Properties and Reflection Loss in the Co 0.5 Ni 0.5 Ti (1− x ) Y x O 3
Yttrium‐doped nickel cobalt titanate with a nominal composition of Ni 0.5 Co 0.5 Ti (2‐ x ) Y x O 3 ( x = 0.0; 0.025; 0.050 and 0.075) is synthesized by the solid‐state reaction method using mechanical milling from NiO, Co 3 O 4 , Y 2 O 3 , and TiO 2 powders as raw materials in a mole ratio. The effect of Y 3+ doping on particle size stability, structural, magnetic properties, and microwave absorption characteristics of the perovskite Ni 0.5 Co 0.5 Ti (2‐ x ) Y x O 3 has been studied in this research. All samples are investigated using X‐ray diffraction, scanning electron microscope, energy dispersive spectroscopy, vibration sample magnetometer, and vector network analyzer. It is found that all samples show a single phase with a hexagonal structure. The presence of Y 3+ ions dopant can inhibit polygonal particles, and it is able to maintain the particle size stable. In contrast, this material's magnetic properties and microwave absorption capabilities do not experience significant changes with the presence of Y 3+ ions dopant.
- 25 July 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (2)
The Addition of Yttrium Ions Doping to Increase the Stability of Particle Size and its Effect on the Magnetic Properties and Reflection Loss in the Co 0.5 Ni 0.5 Ti (1− x ) Y x O 3
Yttrium‐doped nickel cobalt titanate with a nominal composition of Ni 0.5 Co 0.5 Ti (2‐ x ) Y x O 3 ( x = 0.0; 0.025; 0.050 and 0.075) is synthesized by the solid‐state reaction method using mechanical milling from NiO, Co 3 O 4 , Y 2 O 3 , and TiO 2 powders as raw materials in a mole ratio. The effect of Y 3+ doping on particle size stability, structural, magnetic properties, and microwave absorption characteristics of the perovskite Ni 0.5 Co 0.5 Ti (2‐ x ) Y x O 3 has been studied in this research. All samples are investigated using X‐ray diffraction, scanning electron microscope, energy dispersive spectroscopy, vibration sample magnetometer, and vector network analyzer. It is found that all samples show a single phase with a hexagonal structure. The presence of Y 3+ ions dopant can inhibit polygonal particles, and it is able to maintain the particle size stable. In contrast, this material's magnetic properties and microwave absorption capabilities do not experience significant changes with the presence of Y 3+ ions dopant.