Shizhong Cui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shizhong Cui has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Jianxin He
Zhongyuan University of Technology
3 shared publications - Kun Qi
Research Institute of Textile and Clothing Industries
2 shared publications - Liwei Mi
Zhongyuan University of Technology
2 shared publications - Weihua Chen
Zhengzhou University
2 shared publications - Bin Ding
Innovation Center for Textile Science and Technology Donghua University Shanghai China
1 shared publication - Chuntai Liu
Zhengzhou University
1 shared publication
Latest Publications
- 24 May 2021
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 3 (6) , 3093-3102
Superwettable Amidoximed Polyacrylonitrile-Based Nanofibrous Nonwovens for Rapid and Highly Efficient Separation of Oil/Water Emulsions
- 24 May 2021
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 3 (6) , 3093-3102
Superwettable Amidoximed Polyacrylonitrile-Based Nanofibrous Nonwovens for Rapid and Highly Efficient Separation of Oil/Water Emulsions
- Open Access
- 11 January 2021
- Published by SAGE Publications in Journal of Engineered Fibers and Fabrics
- Vol. 16
Methods for improving the accuracy of CIE tristimulus values of object color by calculation Part II: Improvement on measurement wavelength ranges
The previous paper (part I) analyzed test errors of the spectrophotometer and their reasons, then systematically investigated the algorithms to reduce measuring bandpass error and intervals error. This paper (part II) focuses on the influence of measurement wavelength ranges and their truncation errors, and some algorithms to overcome the truncation errors. CIE recommends that tristimulus values are calculated over a range of 360–830 nm. However, most spectrophotometers do not meet it. The reduction of measurement range will result in a measurement range error or a truncation error. In this study, five ranges commonly employed in practice are selected for investigating the truncation errors, and three extrapolation methods are used to extend the data to compensate for the measurement range loss. Results are obtained by employing 1301 Munsell color chips under illuminant D65 and CIE 1964 standard observer. For the standard 1-nm intervals, the narrower the range, the larger the truncation error. For the usual-measured 10-nm intervals, bandpass error and intervals error should be handled at the same time, 380–780 nm Table LWL gives the highest accurate outcomes, which even improve the accuracy of the range 360–750 nm to an acceptable level. Whereas, ranges of 360–700 nm and 400–700 nm still need extrapolation to reduce their truncation errors even with Table LWL. Three extrapolation methods of nearest, linear and second-order all reduce the truncation error, but for different ranges, algorithms and illuminants, the optimal method of extrapolation varies.
- 11 January 2021
- Published by SAGE Publications in Journal of Engineered Fibers and Fabrics
- Vol. 16
Open AccessMethods for improving the accuracy of CIE tristimulus values of object color by calculation Part II: Improvement on measurement wavelength ranges
The previous paper (part I) analyzed test errors of the spectrophotometer and their reasons, then systematically investigated the algorithms to reduce measuring bandpass error and intervals error. This paper (part II) focuses on the influence of measurement wavelength ranges and their truncation errors, and some algorithms to overcome the truncation errors. CIE recommends that tristimulus values are calculated over a range of 360–830 nm. However, most spectrophotometers do not meet it. The reduction of measurement range will result in a measurement range error or a truncation error. In this study, five ranges commonly employed in practice are selected for investigating the truncation errors, and three extrapolation methods are used to extend the data to compensate for the measurement range loss. Results are obtained by employing 1301 Munsell color chips under illuminant D65 and CIE 1964 standard observer. For the standard 1-nm intervals, the narrower the range, the larger the truncation error. For the usual-measured 10-nm intervals, bandpass error and intervals error should be handled at the same time, 380–780 nm Table LWL gives the highest accurate outcomes, which even improve the accuracy of the range 360–750 nm to an acceptable level. Whereas, ranges of 360–700 nm and 400–700 nm still need extrapolation to reduce their truncation errors even with Table LWL. Three extrapolation methods of nearest, linear and second-order all reduce the truncation error, but for different ranges, algorithms and illuminants, the optimal method of extrapolation varies.
- 26 July 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 53 (22) , 15735-15745
Novel method for preparation of continuously twisted nanofiber yarn based on a combination of stepped airflow electrospinning and friction twisting
- 26 July 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 53 (22) , 15735-15745
Novel method for preparation of continuously twisted nanofiber yarn based on a combination of stepped airflow electrospinning and friction twisting
- 24 April 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 5 (20) , 10027-10038
Synergistic effect induced ultrafine SnO2/graphene nanocomposite as an advanced lithium/sodium-ion batteries anode
A synergistic effect induced ultrafine-SnO2/graphene nanocomposite is synthesized via a simple method as an advanced lithium/sodium-ion batteries anode material.
- 24 April 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 5 (20) , 10027-10038
Synergistic effect induced ultrafine SnO2/graphene nanocomposite as an advanced lithium/sodium-ion batteries anode
A synergistic effect induced ultrafine-SnO2/graphene nanocomposite is synthesized via a simple method as an advanced lithium/sodium-ion batteries anode material.
- 6 January 2016
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 45 (8) , 3305-3309
An N-doped three dimensional flexible carbon/sulfur cathode for lithium sulfur battery design
Nitrogen-doped flexible carbon foam was used to fabricate a lithium sulfur battery.
- 6 January 2016
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 45 (8) , 3305-3309
An N-doped three dimensional flexible carbon/sulfur cathode for lithium sulfur battery design
Nitrogen-doped flexible carbon foam was used to fabricate a lithium sulfur battery.
- 17 October 2013
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 23 (1) , 13-25
Fabrication of nanofibers by a modified air-jet electrospinning method
- 17 October 2013
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 23 (1) , 13-25
Fabrication of nanofibers by a modified air-jet electrospinning method